RS2258 Second-Side Regulation Current Mode PWM Power Switcher DESCRIPTION RS2258 combines a dedicated current mode PWM controller with a high voltage power MOSFET. It is optimized for high performance, low standby power, and cost effective off‐line flyback converter applications in sub 27W range. RS2258 offers complete protection coverage with automatic self‐recovery feature including Cycle‐by‐Cycle current limiting (OCP), over load protection (OLP), VDD over voltage clamp and under voltage lockout (UVLO). Excellent EMI performance is achieved with Orister proprietary frequency Jiggling technique together with soft switching control at the totem pole gate drive output. The tone energy at below 20KHz is minimized in the design and audio noise is eliminated during operation. RS2258 is offered in DIP‐8 package. APPLICATIONS • • • • • • • Battery Charger Digital Cameras and camcorder Adaptor PDA power supplies VCR, SVR, STB, DVD & DVCD Player SMPS Set‐Top Box (STB) Power Auxiliary Power Supply for PC and Server Open‐frame SMPS FEATURES • Power on Soft Start Reducing MOSFET VDS Stress • Frequency Jiggling to reduce EMI • Burst Mode Control For Improved Efficiency and Minimum • Standby power Design • Audio Noise Free Operation • Fixed 50KHz Switching Frequency • Internal Synchronized Slope Compensation • Low VDD Startup Current and Low Operating Current • Leading Edge Blanking on Current Sense Input • Good Protection Coverage With Auto Self‐Recovery - VDD Over Voltage Clamp and Under Voltage Lockout with Hysteresis (UVLO) - Line Input Compensated Cycle‐by‐Cycle Over‐current Threshold Setting For Constant Output Power Limiting Over Universal Input Voltage Range - Overload Protection (OLP) - Over Voltage Protection (OVP) • DIP‐8 Package • RoHS Compliant and 100% Lead (Pb)‐Free and Green (Halogen NFree with Commercial Standard) BLOCK DIAGRAM Tel: 886-66296288‧Fax: 886-29174598‧ http://www.princeton.com.tw‧2F, No. 233-1, Baociao Rd., Sindian Dist., New Taipei City 23145, Taiwan RS2258 APPLICATION CIRCUIT 1 1 L1 4 - + 2 AC IN C1 C4 T1 D1 C2 R5 R2 VOUT D4 C5 R1 3 2 Np D2 R3 C3 Ns C6 R6 D3 Naux GND U2 U1 VDDG VDD FB GND GND 4 1 3 2 R7 R9 C8 DRAIN SENSE DRAIN D5 RS2258 R4 C7 RS431 R8 R10 ORDER INFORMATION Device RS2258 Y Z V1.0 Device Code Y is package designator : P: DIP-8 Z is Lead Free designator : P: Commercial Standard, Lead (Pb) Free and Phosphorous (P) Free Package G: Green (Halogen Free with Commercial Standard) 2 January 2013 RS2258 PIN CONFIGURATION PIN DESCRIPTION Symbol VDDG VDD FB SENSE DRAIN GND V1.0 Description Internal Gate Driver Power Supply Pin DC Power Supply Input Pin Feedback input Pin. The PWM duty cycle is determined by voltage level into this pin and the current-sense signal at Pin 4 Current Sense Input Pin HV MOSFET Drain Pin. The Drain pin is connected to the primary lead of the transformer Ground Pin 3 Pin 1 2 3 4 5, 6 7, 8 January 2013 RS2258 FUNCTION DESCRIPTION DETAIL DESCRIPTION The RS2258 is a low power off-line SMPS Switcher optimized for off-line flyback converter applications in sub 10W power range. The burst mode control greatly reduces the standby power consumption and helps the design easily to meet the international power conservation requirements. STARTUP CURRENT AND START UP CONTROL Startup current of RS2258 is designed to be very low so that VDD could be charged up above UVLO threshold level and device starts up quickly. A large value startup resistor can therefore be used to minimize the power loss yet achieve a reliable startup in application. For AC/DC adaptor with universal input range design, a 2MΩ, 1/8W startup resistor could be used together with a VDD capacitor to provide a fast startup and yet low power dissipation design solution. OPERATION CURRENT The Operation current of RS2258 is low at 2mA. Good efficient is achieved with RS2258 low operating current together with the ‘Extended burst mode’ control features. SOFT START RS2258 features an internal 4 ms soft start to soften the electrical stress occurring in the power supply during startup. It is activated during the power on sequence. As soon as VDD reaches UVLO(OFF), the peak current is gradually increased from nearly zero to the maximum level of 0.77V. Every restart up is followed by a soft start. FREQUENCY JIGGLING MODE FOR EMI IMPROVEMENT The frequency Jiggling Mode (switching frequency modulation) is implemented in RS2258. The oscillation frequency is modulated so that the tone energy is spread out. The spread spectrum minimizes the conduction band EMI and therefore eases the system design. EXTENDED BURST MODE OPERATION At light load or zero load condition, most of the power dissipation in a switching mode power supply is from switching loss on the MOSFET, the core loss of the transformer and the loss on the snubber circuit. The magnitude of power loss is in proportion to the switching frequency. Lower switching frequency leads to the reduction on the power loss and thus conserves the energy. The switching frequency is internally adjusted at no load or light load condition. The switch frequency reduces at light/no load condition to improve the conversion efficiency. At light load or no load condition, the FB input drops below burst mode threshold level and device enters Burst Mode control. The Gate drive output switches only when VDD voltage drops below a preset level and FB input is active to output an on state to minimize the switching loss and reduce the standby power consumption to the greatest extend. The switching frequency control also eliminates the audio noise at any loading conditions. V1.0 4 January 2013 RS2258 OSCILLATOR OPERATION The switching frequency of RS2258 is internally fixed at 50 KHz. No external frequency setting components are required for PCB design simplification. CURRENT SENSING AND LEADING EDGE BLANKING Cycle-by-Cycle current limiting is offered in RS2258 current mode PWM control. The switch current is detected by sense resistor into the sense pin. An internal leading edge blank circuit chops off the sensed voltage spike at initial internal power MOSFET on state due to snubber diode reverse recovery and surge gate current of internal power MOSFET so that the external RC filtering on sense input is no longer needed. The current limiting comparator is disabled and cannot turn off the internal power MOSFET during the blanking period. The PWM duty cycle is determined by the current sense input voltage and the FB input voltage. INTERNAL SYNCHRONIZED SLOPE COMPENSATION Built‐in slope compensation circuit adds voltage ramp onto the current sense input voltage for PWM generation. This greatly improves the close loop stability at CCM and prevents the sub‐harmonic oscillation and thus reduces the output ripple voltage. DRIVE The internal power MOSFET in RS2258 is driven by a dedicated gate driver for power switch control. Too weak the gate driving strength results in higher conduction and switch loss of MOSFET while too strong gate drive results the compromise of EMI. A good tradeoff is achieved through the built‐in totem pole gate design with right output strength and dead time control. The low idle loss and good EMI system design is easier to achieve with this dedicated control scheme. In addition to the gate drive control scheme mentioned, the gate drive strength can also be adjusted externally by a resistor connected between VDD and VDDG, the falling edge of the Drain output can be well controlled. It provides great flexibility for system EMI design. PROTECTION CONTROLS Good power supply system reliability is achieved with its rich protection features including Cycle‐by‐Cycle current limiting (OCP), Over Load Protection (OLP) and over voltage clamp, Under Voltage Lockout on VDD (UVLO). With Orister Proprietary technology, the OCP is line voltage compensated to achieve constant output power limit over the universal input voltage range. At overload condition when FB input voltage exceeds power limit threshold value for more than TD_PL, control circuit reacts to shut down the switcher. Switcher restarts when VDD voltage drops below UVLO limit. VDD is supplied by transformer auxiliary winding output. It is clamped when VDD is higher than 30V. The output of RS2258 is shut down when VDD drops below UVLO(ON) limit and Switcher enters power on start‐up sequence thereafter. V1.0 5 January 2013 RS2258 ABSOLUTE MAXIMUM RATINGS Parameter Drain Voltage (off state) VDD Voltage VDDG Input Voltage VDD Clamp Continuous Current FB Input Voltage Sense Input Voltage Operating Ambient Temperature Storage Temperature Lead Temperature (soldering, 10sec) Symbol VDRAIN VDD VDDG IN IVDD CLAMP VFB IN VSENSE IN TOPR TSTG - Ratings -0.3 to 650 -0.3 to 30 -03 to 30 10 -0.3 to 7 -0.3 to 7 -40 to +85 -40 to +150 +260 Units V V V mA V V o C o C o C Note: 1. Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and function operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute‐maximum–rated conditions for extended periods may affect device reliability. 2. Caution: Stress above the listed absolute maximum rating may cause permanent damage to the device. * HBM B: 2000V to 3999V OUTPUT POWER TABLE 230VAC ±15% Open Frame (Note) 21W DIP-8 Package 85 to 265VAC Open Frame (Note) 18W o Note: Maximum practical continuous power in an open frame design with sufficient drain pattern as a heat sink, at 50 C ambient. V1.0 6 January 2013 RS2258 ELECTRICAL CHARACTERISTICS (Unless stated otherwise, PVH=12V, Test bandwidth=22~22KHz) Parameter Symbol Test Conditions Supply Voltage (VDD) VDD=14.5V, Measure Leakage VDD Start up Current Istartup current into VDD Operation Current IVDD VFB=3V VDD Under Voltage Lockout Enter UVLO(ON) VDD Under Voltage Lockout UVLO(OFF) Exit(Recovery) CS=0V, FB=3V Ramp up VDD Over voltage protection voltage OVP(ON) until gate clock is off VDD Zener clamp Voltage VDD CLAMP IDD=10mA Feedback Input Section(FB pin) VFB Open Loop Voltage VFB OPEN Short FB pin to GND and FB pin short circuit current IFB_SHORT measure current Zero Duty Cycle FB Threshold VTH_0D Voltage Power Limiting FB Threshold VTH_PL Voltage Power Limiting Debounce Time TD PL Input Impedance ZFB IN Current Sense Input(Sense Pin) Soft start time TSOFTSTART Leading edge blanking time TBLANKING Input Impedance ZSENSE IN From Over Current Occurs till Over Current Detection and TD_OC the Gate drive output start to turn Control Delay off Internal Current Limiting VTH_OC FB=3.3V Threshold Voltage Oscillator Normal Oscillation Frequency FOSC Frequency Temperature Stability ΔFTEMP Frequency Voltage Stability ΔF_VDD Maximum duty cycle DMAX FB=3.3V, CS=0V Burst Mode Base Frequency FBURST Power MOSFET Section MOSFET Drain Source VGS=0V, IDS=250uA B_VDSS Breakdown Voltage Static Drain to Source On RDS(ON) VGS=10V, IDS=1A Resistance Frequency Frequency Modulation range ΔF_VDD /Base frequency V1.0 7 Min Typ. Max Unit - 3.0 20 μA 8.5 2.0 9.0 9.5 mA V 14.2 15.8 16.0 V 27.0 28.5 30.0 V - 30 - V 5.4 5.6 6.0 V - 1.55 - mA - 0.8 - V - 3.7 - V - 50 4 - ms KΩ - 4 300 40 - ms ns KΩ - 120 - ns 0.76 0.8 0.82 V 45 70 - 50 5 5 80 22 55 90 - KHz % % % KHz 620 650 - V - 3.0 3.6 Ω -4 - 4 % January 2013 RS2258 PACKAGE INFORMATION 8 PINS, DIP Notes:. 1. All dimensions are in millimeters. 2. Refer to JEDEC MS‐001 V1.0 8 January 2013 RS2258 IMPORTANT NOTICE Princeton Technology Corporation (PTC) reserves the right to make corrections, modifications, enhancements, improvements, and other changes to its products and to discontinue any product without notice at any time. PTC cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a PTC product. No circuit patent licenses are implied. Princeton Technology Corp. 2F, 233-1, Baociao Road, Sindian, Taipei 23145, Taiwan Tel: 886-2-66296288 Fax: 886-2-29174598 http://www.princeton.com.tw V1.0 9 January 2013