Ka-Band 700 W High Power Amplifier Built for Outdoor Applications Rugged, compact and lightweight amplifier designed for outdoor use. Typically provides 600 W of CW power at the flange in standard bands within the 27 to 31 GHz frequency range (24.75 to 25.25 GHz optional). Cost Effective and Efficient Mounting at the antenna improves performance by reducing IFL losses and saves cost in system design. Provides up to 365 W of linear power at the amplifier flange. Rugged, Easy to Maintain, Simple to Operate Built-in fault diagnostic capability via remote monitor and control. Easy access enclosure for improved serviceability. CAN-Bus architecture improves reliability and improves noise immunity. User-friendly microprocessor-controlled logic with integrated Ethernet computer interface. Meets Global Requirements Meets International Safety Standard EN-60215, Electromagnetic Compatibility 2004/108/EC and Harmonic Standard EN-61000-3-2 to satisfy worldwide requirements. CE certified. Model C07KO 700 watt Ka-band outdoor TWTA for satellite uplink applications OPTIONS •Remote control panel •Integral linearizer •Integrated 1:1 switch control and drive •Redundant and power combined subsystems •RS 422/485 serial interface •Integral single or multi-band, L-band block upconverter (BUC). Contact CPI for specifications •TWT LifeExtender™ Worldwide Support Backed by over three decades of satellite communications experience, and CPI’s worldwide 24-hour customer support network that includes more than 20 regional factory service centers. 811 Hansen Way, PO Box 51625 Palo Alto, CA 94303 USA tel: +1 (650) 846-3803 fax: +1 (650) 424-1744 e-mail:[email protected] website:www.cpii.com/satcom Ka-Band Specifications 700 W Ka-Band High Power Amplifier Specification Output Frequency Range Model C07KO 27.0 to 31.0 GHz; 27.35 to 30.0 GHz, 28.35 to 30.50 GHz; 29.0 to 31.0 GHz; 30.0 to 31.0 GHz; 24.75 to 25.25 GHz; others available (contact CPI) TWT Output Power 700 W min. (58.5 dBm) Flange CW Power 580 W min. (57.6 dBm) Intermodulation - with respect to the sum of two carriers -25 dBc max. at total output power of 365 W with optional linearizer Intermodulation - with respect to each of two equal carriers 5 MHz apart -25 dBc max. at total output power of 260 W with optional linearizer Gain RF Level Adjust Range Gain Stability 70 dB min; 73 dB typ. at 7 dB backoff from rated power 0 to 30 dB (via PIN diode attenuator) typ, 0.1 dB steps ±0.25 dB/24 hour max, at constant drive and temperature Small Signal Gain Slope Small Signal Gain Variation 0.05 dB/MHz max. 4.0 dB pk-pk max. across any 2000 MHz band Input/Output VSWR 1.3:1 max. Load VSWR 2.0:1 max. operational; any value for operation without damage Phase Noise -12 dB below IESS-308 continuous mask; -47 dBc AC fundamental; -50 dBc sum of all spurs AM/PM Conversion 2.0˚/dB max. for a single-carrier up to 7 dB OBO (up to 3 dB OBO with optional linearizer) Harmonic Outputs Noise Density Noise Power Ratio Spectral Regrowth Group Delay (over 40 MHz) Primary Power -65 dB max. (RF); -60 dB max. (IF) <-150 dBW/4 kHz below 21.2 GHz; <-70 dBW/4 kHz max. in passband 19 dB at 4 dB OBO (235 W) with linearizer; 22 dB at 5 dB OBO with linearizer; 25 dB at 6 dB OBO with linearizer; 32 dB at 10 dB OBO with linearizer -30 dBc max. at 2.5 dB OBO (330 W) with linearizer 0.01 ns/MHz linear max; 0.001 ns/MHz2 parabolic max; 1.5 ns pk-pk ripple max. Voltage: Single phase, 100-240 VAC ±10%; Frequency: 47-63 Hz Power Consumption 2.5 kVA max. Power Factor 0.95 min; 0.99 typ. Amplitude and Phase Linearity Ambient Temperature Exceeds MIL-STD-188-164A -40˚C to +55˚C operating in direct sunlight (to +60˚C out of direct sunlight); -50˚C to +71˚C non-operating Relative Humidity Altitude Shock and Vibration 100% condensing 10,000 ft. with standard adiabatic derating of 2˚C/1000 ft. operating; 50,000 ft. non-operating 20 G at 11 ms (1/2 sine pulse in non-operating condition); 2.1 g rms, 50 to 500 MHz Cooling RF Input Connection RF Output Connection Forced Air with integral blower WR-28 cover flange waveguide (WR-34 cover flange optional); WR-34 flange required for 24.75 to 25.25 GHz operation WR-34 grooved waveguide with grooved UT-1530/U waveguide flange (WR-28 optional); WR-34 grooved waveguide required for 24.75 to 25.25 GHz operation RF Monitor M&C Interface Dimensions, W x H x D 2.9 mm coaxial, female Ethernet (RS232/422/485 serial optional) 12.75 x 11.5 x 22.25 inches (324 x 292 x 566 mm) Weight 79 lbs (35.9 kg) max. with no options Heat Dissipation 1800 W max. Acoustic noise 65 dBA (as measured at 3 ft.) nom. Quality Management System - ISO 9001:2008 For more detailed information, please refer to the corresponding CPI technical description if one has been published, or contact CPI. Specifications may change without notice as a result of additional data or product refinement. Please contact CPI before using this information for system design. MKT 332, ISSUE 14 dated AUG 2015