TL02KO - Communications & Power Industries

Ka-Band
250 W SuperLinear® Outdoor TWT BUC
Built for Outdoor Applications
Provides 250 watts of peak power in a rugged and compact
weatherproof package, digital ready, for wideband singleand multi-carrier satellite service over up to 3.5 GHz within
the Ka-band frequency band. Ideal for both transportable
and fixed earth station applications.
Cost Effective and Highly Efficient
As part of the SuperLinear TWTA product line, this is the
most efficient and compact amplifer in its class. Both the
tube and HPA are optimized for efficient operation at linear
power output levels.
Rugged and Easy to Maintain
Built-in fault diagnostic capability via remote monitor and
control. Easy access enclosure for improved serviceability.
CAN-Bus architecture improves reliability and improves
noise immunity.
Meets Global Requirements
Meets International Safety Standard EN-60215,
Electromagnetic Compatibility 2004/108/EC
and Harmonic Standard EN-61000-3-2 to satisfy worldwide
requirements. CE certified. Meets EMI per MIL-STD-461F
RE102 and CS114-116 Army Ground Profile.
Model TL02KO
250 watt Ka-band outdoor TWTB for
satellite uplink applications
OPTIONS
•Remote control panel
•Internal 1:1 switch control and drive
•Redundant or power combined
subsystems
•Integral single- or multi-band L-Band Block
Upconverter (BUC) - contact CPI or consult
document TD-193 for specifications when
BUC is included
•RS-422/485 serial interface
•This product is also available without
a block upconverter - contact CPI for
specifications
Worldwide Support
Backed by over three decades of satellite communications
experience, and CPI’s worldwide 24-hour customer
support network that includes more than 20 regional
factory service centers.
811 Hansen Way, PO Box 51625
Palo Alto, CA 94303 USA
tel:
+1 (650) 846-3803
fax:
+1 (650) 424-1744
e-mail:[email protected]
website:www.cpii.com/satcom
Ka-Band
Specifications 250 W SuperLinear Ka-Band Outdoor TWTB
Specification
Model TL02KO
Output Frequency
Up to 3500 MHz instantaneous bandwidth within the 27.0 to 31.0 GHz frequency band (multi-band BUC option allows for two
different, factory-set frequency ranges, each up to 1 GHz - contact CPI for more information)
TWT Peak Power1
250 W (54.0 dBm)
Flange Peak Power1
220 W (53.4 dBm)
Linear Power at Flange1
110 W (50.4 dBm) min with linearizer
CW Power at Flange
Intermodulation - with respect
to the sum of two carriers
130 W (51.1 dBm)
-25 dBc max. at total output power of 50 W (at 110 W with linearizer)
Gain
RF Level Adjust Range
Gain Stability
64 dB min. (67 dB typ. at small signal)
0 to 30 dB (via PIN diode attenuator) typ, 0.1 dB steps
±0.25 dB/24 hour max,max. at constant drive and temperature, after 30 minute warmup
±2.0 dB max. from -40˚C to +60˚C
Small Signal Gain Slope
Small Signal Gain Variation
±0.04 dB/MHz max.
1.0 dB pk-pk max. across any 80 MHz segment; 3.0 dB pk-pk max. across 1 GHz segment
Input/Output VSWR
Load VSWR
1.5:1 max/1.3:1 max.
2.0:1 max. continuous operation, any value operation without damage
MUXed External 10 MHz
Reference Phase Noise
Required (L-Band Input 950
to 1700 MHz)
-120 dBc/Hz at 10 Hz
-140 dBc/Hz at 100 Hz
-145 dBc/Hz at 1 kHz
-150 dBc/Hz at �10 kHz
Single Sideband Phase Noise
-33 dBc at 10 Hz offset; -63 dBc at 100 Hz offset;
-73 dBc at 1 kHz offset; -83 dBc at 10 kHz offset;
-93 dBc at 100 kHz offset; -103 dBc at 1 MHz offset;
-113 dBc at �10 MHz offset
Spurious
-60 dBc max.
AM/PM Conversion
2.0˚/dB max. with optional linearizer
Harmonic Output
Noise Density
-60 dBc with optional filter
<-150 dBW/4 kHz below 21.2 GHz; <-65 dBW/4 kHz max. in passband; <-60 dBW/4 kHz max. in passband with linearizer option
Spectral Regrowth
Group Delay (over 40 MHz)
Primary Power
-30 dBc max. @ 1 symbol rate
0.01 ns/MHz linear max; 0.001 ns/MHz2 parabolic max; 0.5 ns pk-pk ripple max.
100 to 240 VAC +/-10% single phase, 47-63 Hz
Power Consumption
700 VA max; 600 VA typ.
Power Factor
0.95 min; 0.99 typ.
Amplitude and Phase Linearity
Ambient Temperature
Exceeds MIL-STD-188-164B
-40˚C to +60˚C operating in direct sunlight (to +65˚C out of direct sunlight); -54˚C to +71˚C non-operating
Relative Humidity
Altitude
Shock and Vibration
100% condensing
10,000 ft. with standard adiabatic derating of 2˚C/1000 ft. operating; 50,000 ft. non-operating
20 G at 11 ms (1/2 sine pulse in non-operating condition); 2.1 g rms, 50 to 500 MHz
Cooling
Connections
Forced Air with integral blower
L-Band RF Input: N-type female; RF output: WR-34G (WR-28G optional); RF output monitor: 2.9mm SMA Female
M&C Interface
Dimensions, W x H x D
Ethernet (RS422/485 serial optional)
10.5 x 8.5 x 17.0 inches (267 x 216 x 432 mm)
Weight
32 lbs (14.6 kg) with no options
Acoustic noise
Note 1
65 dBA (as measured at 3 ft.) nom.
Peak power specs are provided so that desired backoff can more easily be calculated. The amplifier’s actual guaranteed minimum output at the flange,
CW power, is 110 W.
Quality Management
System - ISO 9001:2008
For more detailed information, please refer to the corresponding CPI technical description if one has been
published, or contact CPI. Specifications may change without notice as a result of additional data or product
refinement. Please contact CPI before using this information for system design.
MKT 323B, ISSUE 9 dated AUG 2015