T02KO B - Communications & Power Industries

250 W Peak Power Outdoor TWT BUC
for Satellite Uplink Communications
Ka- Band
The T02KO
B-Series
250 Watt Ka-band TWT
High Power Amplifier with
Block Up Converter—
Environmentally sealed
compact design for
outdoor operation
Ka-Band
Global Applications
Rugged, compact and lightweight amplifier
designed for outdoor use.
Meets Electromagnetic Compatibility
2004/108/EC and Harmonic
Standard EN-61000-3-2 to satisfy
worldwide requirements.
Efficient and Cost Effective
Mounting at the antenna improves
performance through minimized cable losses
and saves cost in system design. Employs
a high efficiency helix traveling wave tube,
reducing operating costs. Includes integral
block upconverter (BUC) as standard.
Worldwide Support
Backed by over three decades of satellite
communications experience, and CPI’s
worldwide 24-hour customer support network
that includes sixteen regional factory
service centers.
Simple to Operate
User-friendly microprocessor-controlled logic
with integrated RS422/485 computer interface.
Digital metering is standard.
811 Hansen Way
P.O. Box 51625, Palo Alto, CA 94303
Easy to Maintain
Modular design and built-in fault diagnostic
capability via remote monitor and control.
tel: +1 (650) 846-3803
fax: +1 (650) 424-1744
e-mail: [email protected]
www.cpii.com/satcom
250 W Peak Power Outdoor TWT Amplifier
Plays in the Rain
Ka -B a n d
SPECIFICATIONS,
250 W Ka-band Outdoor LPA
Electrical
OPTIONS:
• 1 RU Remote
Control Panel
• Integrated 1:1
Switch Control
• Redundant and
Power Combined
Subsystems
• Integral
Linearizer
Model Number
Frequency
Output Power
TWT
at Flange (CW)2
Bandwidth
Gain
at rated power
at small signal
RF Level Adjust Range
Attenuator Step Size
Small Signal Gain Slope
Small Signal Gain Variation
Gain Stability (at constant
drive and temperature)
T02KO B Series (includes Block Upconverter as standard)
User-specified frequency range within the 27.5 to 31.0 GHz band, as limited by bandwidth capability of amplifier1
250 W peak power (54.0 dBm), options for 125 W average (51.0 dBm) or 175 W average (52.3 dBm)
200 W peak power (53.0 dBm), options for 100 W average (50.0 dBm) or 145 W average (51.6 dBm)
1000 - 2500 MHz, depending on desired frequency range1
70 dB min.
75 dB min, 70 dB min. with linearizer option
0 to 25 dB
0.1 dB
±0.04 dB/MHz max.
1.0 dB pk-pk (across any 40 MHz segment within the passband)
4.5 dB pk-pk (across any 1000 MHz)
±0.4 dB/24 hours max. (after 30 minute warm-up)
±3.0 dB from -5˚C to +60˚C
VSWR
Phase Noise
AM/PM Conversion
Noise Density
(at rated gain)
Spectral Regrowth
Intermodulation
1.3:1 Input; 1.3:1 Output; 1.5: 1 max. Load --- no degradation, infinite VSWR without damage
3 dB below IESS 308 continuous mask; AC Fundamentals -36 dBc; Sum of All Spurs -41 dBc
2.5˚ /dB max. for a single carrier up to 6 dB OBO (1.0˚ /dB max. up to 3 dB OBO with linearizer option)
<-150 dBW/4 kHz, below 21.2 GHz
<-65 dBW/4 kHz, passband
-30 dBc at 7.0 dB backoff (at 4.0 dB backoff with linearizer option)
-24 dBc or better with two equal carriers at total output power level 7.0 dB
below rated single carrier output (-23 dBc or better at 4.0 dB backoff with linearizer option)
Group Delay
Linear
Parabolic
Ripple
Primary Power
Power Consumption
Power Factor
(in any 40 MHz band)
0.02 nsec/MHz max.
0.007 nsec/MHz sq. max.
1.0 nsec pk-pk max.
100 - 240 VAC ± 10%, 47-63 Hz
750 VA typ, at saturated RF output power; 800 VA max.
0.95 min.
Environmental (operating)
Ambient Temperature
Relative Humidity
Altitude
Shock and Vibration
-40˚ to +60˚ C with extra margin for solar loading
100% condensing
10,000 ft with standard adiabatic derating of 2˚ C/1000 ft
20 g peak, 11 msec, 1/2 sin; 2.1 grms, 5 to 500 Hz
Mechanical
Cooling
RF Connection
RF Output Monitor
Dimensions (WxHxD)
Weight
Forced air with integral blower
Type N Female
2.9 mm SMA Female
13.25 x 9.5 x 20 inches with BUC option (337 x 242 x 508 mm)
58 lbs (26.4 kg)
Heat and Acoustic
Heat Dissipation
Acoustic
600 W typ.
65 dBA typ.
Note 1. Please consult CPI representative to confirm that desired bandwidth is available over desired frequency range.
Note 2. This amplifier does not provide 200 W of power at the flange. The peak power specification is provided so that the desired
backoff level can be more easily calculated.
Mounting hardware is provided with each amplifier.
Certificate Number: 30515
For more detailed information, please refer to the corresponding CPI Technical Description.
Note: Specifications may change without notice as a result of additional data or product refinement.
Please contact CPI before using this information for system design.
MKT 218, ISSUE 3
04/11
PDF