Outdoor TWTAs Ku-Band 750 W SuperLinear® Outdoor TWT Amplifier Built for Outdoor Applications Provides up to 325 watts of linear power in a rugged and compact weatherproof package, digital ready, for satellite uplinks in the 13.75 - 14.50 and 12.75 - 14.50 GHz frequency bands. Cost Effective and Efficient CPI SuperLinear® TWTAs are among the most power efficient in the industry. Also employs a high efficiency, dualdepressed collector helix traveling wave tube, further reducing operating costs. Reliable Designed and built to survive in extremely adverse environmental conditions and features increased cooling margin for longer life. CAN-Bus architecture improves reliability and noise immunity. Optional LifeExtender™ significantly increases TWT lifetime. Simple to Operate User-friendly microprocessor-controlled logic with integrated Ethernet computer interface. Digital metering, pin diode attenuation and optional integrated linearizer for improved intermodulation performance. Standard SNMP facilitates high level M&C integration. Easy to Maintain Modular design and built-in fault diagnostic capability via remote monitor and control. Model TL07UO 750 watt Ku-band SuperLinear® ODU for satellite uplink applications OPTIONS •1 RU and 3 RU remote control panels •Serial interface •Extended frequencies: 12.75 to 14.50, 12.75 to 13.25 and 13.0 to 14.8 GHz* (*contact CPI for specifications) •Redundant and hybrid power combined sub-systems •Integrated 1:1 switch control and drive •Single or multiband L-band block upconverters (BUCs) •Integral linearizer •External receive band reject filter (increases loss by a minimum of 60 dB up to 12.7 GHz) •LifeExtender/LifePredictor to extend TWT life Meets Global Requirements Meets International Safety Standard EN-60215, Electromagnetic Compatibility 2004/108/EC and Harmonic Standard EN-61000-3-2 to satisfy worldwide requirements. CE certified. Worldwide Support Backed by over three decades of satellite communications experience, and CPI’s worldwide 24-hour customer support network that includes more than 20 regional factory service centers. 811 Hansen Way, PO Box 51625 Palo Alto, CA 94303 USA tel: +1 (650) 846-3803 fax: +1 (650) 424-1744 e-mail:[email protected] website:www.cpii.com/satcom Ku-Band Specifications 750 W Ku-Band SuperLinear Outdoor TWT Amplifier ® Specification Model TL07UO Output Frequency 13.75 to 14.50 GHz or 12.75 to 14.50 GHz Input Frequency 950 to 1700 MHz with BUC option Output Power (min.) TWT Flange Peak Power Maximum Power at Flange CW Power at Flange Note on Output Power 750 W (58.75 dBm) min. 650 W (58.13 dBm) min. 365 W (55.62 dBm) min. 325 W (55.12 dBm) min. This amplifier guarantees 325 W of CW power at the flange. The peak power specifications are provided so that desired backoff may be more easily calculated. Gain RF Level Adjust Range Gain Stability Over temp, constant drive 70 dB min. 0 to 30 dB (via PIN diode attenuator) typ, 0.1 dB steps ±0.25 dB/24 hour max,max. at constant drive and temperature, after 30 minute warmup ±1.0 dB typ. over operating temperature range Small Signal Gain Slope Small Signal Gain Variation Input/Output VSWR Load VSWR Phase Noise AM/PM Conversion Harmonic Output Noise Density Intermodulation - with respect to each of 2 equal carriers 5 MHz apart Group Delay Primary Power ±0.02 dB/MHz max. 1.0 dB pk-pk max. across any 80 MHz ; 3.5 dB pk-pk max. across 750 MHz (4.5 dB pk-pk max. across 750 MHz with linearizer); 4.5 dB pk-pk max. across 1750 MHz; (5.5 dB pk-pk max. across 1750 MHz with linearizer) 1.3:1 max. (1.5:1 max. with BUC option) 2.0:1 continuous operation; 1.2:1 for full spec. compliance; any value operation without damage 12 dB below IESS-308/309 phase noise profile (3 dB below profile with BUC option) 2.0˚/dB max. for a single-carrier at 8 dB below rated power (at 3 dB OBO with optional linearizer) -60 dBc at rated power, second and third harmonics <-130 dBW/4 kHz, 10.70 to 12.75 GHz; <-65 dBW/4 kHz passband; <-60 dBW/4 kHz passband with linearizer option -24 dBc max. at output power level of 51.1 dbm (-25 dBc max. at output power level of 55.1 dBm with optional linearizer) 0.01 ns/MHz linear max; 0.001 ns/MHz2 parabolic max; 0.5 ns pk-pk ripple max. (1.5 ns pk-pk ripple max. with BUC option) Voltage: Single phase, 120 VAC ±10%; Frequency: 47-63 Hz (180 to 264 VAC optional) Power Consumption 1.4 kVA typ; 1.65 kVA max. Power Factor 0.95 min; 0.99 typ. Inrush Current Ambient Temperature 200% max. -40˚C to +60˚C operating, -40˚C to +70˚C non-operating Relative Humidity Altitude Shock and Vibration 100% condensing 10,000 ft. with standard adiabatic derating of 2˚C/1000 ft. operating; 50,000 ft. non-operating 20 G at 11 ms (1/2 sine pulse in non-operating condition); 2.1 G rms, 5 to 500 MHz Cooling Connections M&C Interface Dimensions, W x H x D Forced Air with integral blower RF Input: Type N Female; RF output: WR-75 grooved waveguide flange; RF output monitor: Type N Female RJ45 Ethernet, includes embedded GUI control and SNMP; RS422/485, RS232 serial interface optional 10.25 x 10.5 x 20.5 inches (260 x 267 x 521 mm) Weight 55 lbs (25.0 kg) typ. Heat Dissipation 1300 watts max. Acoustic noise 68 dBA (as measured at 3 ft.) nom. Quality Management System - ISO 9001:2008 For more detailed information, please refer to the corresponding CPI technical description if one has been published, or contact CPI. Specifications may change without notice as a result of additional data or product refinement. Please contact CPI before using this information for system design. MKT 327, ISSUE 17 dated AUG 2015