MDB26 - Bruckewell Semi

MDB26
Product profile
Single Phase Ultra Low VF Schottky Bridge Rectifier
General description
Schottky Rectifiers 2 Amp 60V
Features
•
Ideal for printed circuit board.
•
High current capability
•
Reliable low cost construction utilizing molded
plastic technique.
•
Low forward voltage drop
•
Low power loss, high efficiency
•
High surge current capability
•
High temperature soldering guaranteed
260°C /10sec/0.375" lead length at 5 lbs tension
•
Mechanical data
Small size, simple installation.
Case: Molded plastic
Epoxy: UL 94V-0 rate flame retardant
Lead: MIL-STD- 202E, Method 208 guaranteed
Polarity: As marked
Maximum Ratings (Tc=25°C unless otherwise noted)
Parameter
Symbol
MDB26
Unit
Maximum repetitive peak reverse voltage
VRRM
60
V
RMS Voltage (Max.)
VRMS
50
V
Working peak reverse voltage
VRWM
60
V
Total Device
IF(AV)
2
A
8.3ms single half sine-wave superimposed
IFSM
60
A
TJ
-55 to +150
°C
TSTG
-55 to +150
°C
Maximum average forward rectified current
Peak forward surge current
on rated load (JEDEC Method)
Operating junction temperature range
Storage temperature range
THERMAL CHARACTERISTICS
Parameter
Symbol
Value
Unit
Typical thermal resistance
RθJA
85
°C/W
Notes:
(1) Pulse test: 300 μs pulse width, 1 % duty cycle
(2) Pulse test: Pulse width ≤ 40 ms
Publication Order Number: MDB26
©Bruckewell Technology Corporation Rev. A -2014
MDB26
Electrical characteristics (Tc=25°C unless otherwise noted)
OFF CHARACTERISTICS
Parameter
Symbol
Value
Unit
Typical
Max
0.50
0.56
0.46
0.51
Instantaneous forward voltage
at IF=2A, Tj=25°C
VF
at IF=2A, Tj=125°C
Maximum reverse current Tj=25°C
V
200
u'A
50
m'A
165
pF
IR
at working peak reverse voltage Tj=125°C
Junction Capacitance @ DC 5V
CJ
DEVICE MARK
MDB26
Publication Order Number: MDB26
©Bruckewell Technology Corporation Rev. A -2014
MDB26
Characteristic Curves
Publication Order Number: MDB26
©Bruckewell Technology Corporation Rev. A -2014
MDB26
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE
WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Bruckewell Technology Inc., its affiliates, agents, and employees, and all persons acting on its or
their behalf (collectively, “Bruckewell”), disclaim any and all liability for any errors, inaccuracies or
incompleteness contained in any datasheet or in any other disclosure relating to any product.
Bruckewell makes no warranty, representation or guarantee regarding the suitability of the products
for any particular purpose or the continuing production of any product. To the maximum extent
permitted by applicable law, Bruckewell disclaims
(i) Any and all liability arising out of the application or use of any product.
(ii) Any and all liability, including without limitation special, consequential or incidental damages.
(iii) Any and all implied warranties, including warranties of fitness for particular purpose,
non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on
Bruckewell’s knowledge of typical requirements that are often placed on Bruckewell products in
generic applications.
Such statements are not binding statements about the suitability of products for a particular
application. It is the customer’s responsibility to validate that a particular product with the properties
described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance
may vary over time.
Product specifications do not expand or otherwise modify Bruckewell’s terms and conditions of
purchase, including but not limited to the warranty expressed therein.
Publication Order Number: MDB26
©Bruckewell Technology Corporation Rev. A -2014