Fair-Rite Product's Catalog Part Data Sheet, 2744041447 Printed: 2014-06-11 Fair-Rite Products Corp. PO Box J,One Commercial Row, Wallkill, NY 12589-0288 Phone: (888) 324-7748 www.fair-rite.com Application: Suppression Components Where Used: Board Component Part Type: SM Beads (Common-Mode) Fair-Rite Product's Catalog Part Data Sheet, 2744041447 Printed: 2014-06-11 Fair-Rite Products Corp. PO Box J,One Commercial Row, Wallkill, NY 12589-0288 Phone: (888) 324-7748 www.fair-rite.com Frequency Range: Broadband Frequencies 10-300 MHz (44 material) Application: Suppression Components Where Used: Board Component Part Type: SM Beads (Common-Mode) Part Type Information Surface mount common-mode beads are available from Fair-Rite in several materials and sizes. The common-mode bead provides a common magnetic path for the flux generated by the current to the load and the return current from the load. The current compensation results in zero magnetic flux in the bead. -SM Beads on 12 mm tape width are supplied taped and reeled per EIA 481 and IEC 60286-3 standards. SM Beads on 16 and 24 mm tape widths are supplied taped and reeled per EIA 481 and IEC 60286-3 standards. Taped and reeled parts are supplied on a 13'' reel. -SM Beads can also be supplied not taped and reeled and then are bulk packed. This packing method will change the last digit of the part number to a '6'. -Wires are oxygen free high conductivity copper with 100% matte tin plating over a nickel undercoating. -SM Beads meet the solderability specifications when tested in accordance with MIL-STD-202, method 208. After dipping the mounting site of the bead, the solder surface shall be at least 95% covered with a smooth solder coating. The edges of the copper strip are not specified as solderable surfaces. -After preheating the beads to within 100 oC of the soldering temperature, the parts meet the resistance to soldering requirements of EIA-186-10E, temperature 260±5 oC and time 10±1 seconds. -Suggested land patterns are in accordance with the latest revision of IPC-7351. -SM Beads are controlled for impedance limits only. Minimum impedance values are specified for the + marked frequencies. The minimum impedance is typically the listed value less 20%. SM Beads in 44 materials are measured for impedance on the 4193 Vector Impedance Analyzer. The 52 SM Beads are tested for impedance on the 4291A RF Impedance Analyzer. -Recommended storage and operation temperature is -55 oC to 125 oC. -The maximum current rating for these SM Beads is 5 amps. -For any SM Bead requirement not listed, please contact our customer service group for availability and pricing. -Our Surface Mount Bead Kit' (part number 0199000025) is available for prototype evaluation. -Explanation of Part Numbers: Digits 1&2 = product class, 3&4 = material grade, last digit 6 = bulk packed, 7 = taped and reeled. Fair-Rite Product's Catalog Part Data Sheet, 2744041447 Printed: 2014-06-11 Fair-Rite Products Corp. PO Box J,One Commercial Row, Wallkill, NY 12589-0288 Phone: (888) 324-7748 www.fair-rite.com Part Number: 2744041447 Description: 44 COMMON MODE SM BEAD Figure: 1 Preferred Part: Weight: .300 (g) Mechanical Specifications Land Patterns V Dim mm A B C D E F G H J K 2.85 5.60 5.00 1.35 2.54 - mm nominal inch tol inch misc. ±0.20 ±0.20 -0.60 ±0.50 ±0.25 - 0.112 0.220 0.185 0.053 0.100 - - Electrical Specifications Typical Impedance ( ) 10 MHz 12 25 MHz+ 20 100 MHz+ 33 250 MHz 41 300 MHz _ W X Y Z 1.800 0.071 3.000 0.118 2.540 0.100 ref 1.000 0.040 4.000 0.158 Winding Information Turns Wire 1st Wire 2nd Wire Tested Size Length Length - - - - Reel Information Tape Width Pitch Parts 7 '' Parts 13 '' Parts 14 '' mm mm Reel Reel Reel 12 8 - 2400 - Package Size Pkg Size (-) Connector Plate # Holes # Rows - - Electrical Properties Max Rdc(m ) 1.10 Legend + Test frequency Preferred parts, the suggested choice for new designs,have shorter lead times and are more readily available. The column H(Oe) gives for each bead the calculated dc bias field in oersted for 1 turn and 1 ampere direct current. The actual dc H field in the application is this value of H times the actual NI (ampere-turn) product. For the effect of the dc bias on the impedance of the bead material, see figures 18-23 in the application note How to choose Ferrite Components for EMI Suppression. A ½ turn is defined as a single pass through a hole. l/A - Core Constant Ae : Effective Cross-Sectional Area L AL - Inductance Factor (__ N 2) N/AWG - Number of Turns/Wire Size for Test Coil l e : Effective Path Length Ve : Effective Core Volume Nl - Value of dc Ampere-turns Fair-Rite Product's Catalog Part Data Sheet, 2744041447 Printed: 2014-06-11 Fair-Rite Products Corp. PO Box J,One Commercial Row, Wallkill, NY 12589-0288 Phone: (888) 324-7748 www.fair-rite.com Fair-Rite Product's Catalog Part Data Sheet, 2744041446 Printed: 2014-06-11 Fair-Rite Products Corp. PO Box J,One Commercial Row, Wallkill, NY 12589-0288 Phone: (888) 324-7748 www.fair-rite.com Part Number: 2744041446 Description: 44 COMMON MODE SM BEAD Figure: 1 Preferred Part: Weight: .300 (g) Mechanical Specifications Land Patterns V Dim mm A B C D E F G H J K 2.85 5.60 5.00 1.35 2.54 - mm nominal inch tol inch misc. ±0.20 ±0.20 -0.60 ±0.50 ±0.25 - 0.112 0.220 0.185 0.053 0.100 - - Electrical Specifications Typical Impedance ( ) 10 MHz 12 25 MHz+ 20 100 MHz+ 33 250 MHz 41 300 MHz _ W X Y Z 1.800 0.071 3.000 0.118 2.540 0.100 ref 1.000 0.040 4.000 0.158 Winding Information Turns Wire 1st Wire 2nd Wire Tested Size Length Length - - - - Reel Information Tape Width Pitch Parts 7 '' Parts 13 '' Parts 14 '' mm mm Reel Reel Reel - - - - - Package Size Pkg Size (-) Connector Plate # Holes # Rows - - Electrical Properties Max Rdc(m ) 1.10 Legend + Test frequency Preferred parts, the suggested choice for new designs,have shorter lead times and are more readily available. The column H(Oe) gives for each bead the calculated dc bias field in oersted for 1 turn and 1 ampere direct current. The actual dc H field in the application is this value of H times the actual NI (ampere-turn) product. For the effect of the dc bias on the impedance of the bead material, see figures 18-23 in the application note How to choose Ferrite Components for EMI Suppression. A ½ turn is defined as a single pass through a hole. l/A - Core Constant Ae : Effective Cross-Sectional Area L AL - Inductance Factor (__ N 2) N/AWG - Number of Turns/Wire Size for Test Coil l e : Effective Path Length Ve : Effective Core Volume Nl - Value of dc Ampere-turns Fair-Rite Product's Catalog Part Data Sheet, 2744041446 Printed: 2014-06-11 Fair-Rite Products Corp. PO Box J,One Commercial Row, Wallkill, NY 12589-0288 Phone: (888) 324-7748 www.fair-rite.com Fair-Rite Product's Catalog Part Data Sheet, 2744045447 Printed: 2014-06-11 Fair-Rite Products Corp. PO Box J,One Commercial Row, Wallkill, NY 12589-0288 Phone: (888) 324-7748 www.fair-rite.com Part Number: 2744045447 Description: 44 COMMON MODE SM BEAD Figure: 1 Preferred Part: Weight: .530 (g) Mechanical Specifications Land Patterns V Dim mm A B C D E F G H J K 2.85 5.60 8.90 1.35 2.54 - mm nominal inch tol inch misc. ±0.20 ±0.20 -0.80 ±0.50 ±0.25 - 0.112 0.220 0.335 0.053 0.100 - - Electrical Specifications Typical Impedance ( ) 10 MHz 23 25 MHz+ 38 100 MHz+ 60 250 MHz 78 300 MHz _ W X Y Z 1.800 0.071 3.000 0.118 2.540 0.100 ref 4.000 0.158 7.000 0.276 Winding Information Turns Wire 1st Wire 2nd Wire Tested Size Length Length - - - - Reel Information Tape Width Pitch Parts 7 '' Parts 13 '' Parts 14 '' mm mm Reel Reel Reel 16 8 - 2400 - Package Size Pkg Size (-) Connector Plate # Holes # Rows - - Electrical Properties Max Rdc(m ) 1.40 Legend + Test frequency Preferred parts, the suggested choice for new designs,have shorter lead times and are more readily available. The column H(Oe) gives for each bead the calculated dc bias field in oersted for 1 turn and 1 ampere direct current. The actual dc H field in the application is this value of H times the actual NI (ampere-turn) product. For the effect of the dc bias on the impedance of the bead material, see figures 18-23 in the application note How to choose Ferrite Components for EMI Suppression. A ½ turn is defined as a single pass through a hole. l/A - Core Constant Ae : Effective Cross-Sectional Area L AL - Inductance Factor (__ N 2) N/AWG - Number of Turns/Wire Size for Test Coil l e : Effective Path Length Ve : Effective Core Volume Nl - Value of dc Ampere-turns Fair-Rite Product's Catalog Part Data Sheet, 2744045447 Printed: 2014-06-11 Fair-Rite Products Corp. PO Box J,One Commercial Row, Wallkill, NY 12589-0288 Phone: (888) 324-7748 www.fair-rite.com Fair-Rite Product's Catalog Part Data Sheet, 2744045446 Printed: 2014-06-11 Fair-Rite Products Corp. PO Box J,One Commercial Row, Wallkill, NY 12589-0288 Phone: (888) 324-7748 www.fair-rite.com Part Number: 2744045446 Description: 44 COMMON MODE SM BEAD Figure: 1 Preferred Part: Weight: .530 (g) Mechanical Specifications Land Patterns V Dim mm A B C D E F G H J K 2.85 5.60 8.90 1.35 2.54 - mm nominal inch tol inch misc. ±0.20 ±0.20 -0.80 ±0.50 ±0.25 - 0.112 0.220 0.335 0.053 0.100 - - Electrical Specifications Typical Impedance ( ) 10 MHz 23 25 MHz+ 38 100 MHz+ 60 250 MHz 78 300 MHz _ W X Y Z 1.800 0.071 3.000 0.118 2.540 0.100 ref 4.000 0.158 7.000 0.276 Winding Information Turns Wire 1st Wire 2nd Wire Tested Size Length Length - - - - Reel Information Tape Width Pitch Parts 7 '' Parts 13 '' Parts 14 '' mm mm Reel Reel Reel - - - - - Package Size Pkg Size (-) Connector Plate # Holes # Rows - - Electrical Properties Max Rdc(m ) 1.40 Legend + Test frequency Preferred parts, the suggested choice for new designs,have shorter lead times and are more readily available. The column H(Oe) gives for each bead the calculated dc bias field in oersted for 1 turn and 1 ampere direct current. The actual dc H field in the application is this value of H times the actual NI (ampere-turn) product. For the effect of the dc bias on the impedance of the bead material, see figures 18-23 in the application note How to choose Ferrite Components for EMI Suppression. A ½ turn is defined as a single pass through a hole. l/A - Core Constant Ae : Effective Cross-Sectional Area L AL - Inductance Factor (__ N 2) N/AWG - Number of Turns/Wire Size for Test Coil l e : Effective Path Length Ve : Effective Core Volume Nl - Value of dc Ampere-turns Fair-Rite Product's Catalog Part Data Sheet, 2744045446 Printed: 2014-06-11 Fair-Rite Products Corp. PO Box J,One Commercial Row, Wallkill, NY 12589-0288 Phone: (888) 324-7748 www.fair-rite.com Fair-Rite Product's Catalog Part Data Sheet, 2744051447 Printed: 2014-06-11 Fair-Rite Products Corp. PO Box J,One Commercial Row, Wallkill, NY 12589-0288 Phone: (888) 324-7748 www.fair-rite.com Part Number: 2744051447 Description: 44 COMMON MODE SM BEAD Figure: 2 Preferred Part: Weight: 1.000 (g) Mechanical Specifications Land Patterns V Dim mm A B C D E F G H J K 4.50 6.65 12.00 2.50 3.00 - mm nominal inch tol inch misc. Max Max Max ±0.50 ±0.10 - 0.177 0.262 0.472 0.098 0.118 - Max Max Max - Electrical Specifications Typical Impedance ( ) 10 MHz 60 25 MHz+ 100 100 MHz+ 230 250 MHz _ 300 MHz 275 W X Y Z 1.000 0.040 5.000 0.197 3.000 0.118 ref 4.000 0.158 9.000 0.354 Winding Information Turns Wire 1st Wire 2nd Wire Tested Size Length Length - - - - Reel Information Tape Width Pitch Parts 7 '' Parts 13 '' Parts 14 '' mm mm Reel Reel Reel 24 12 - 1000 - Package Size Pkg Size (-) Connector Plate # Holes # Rows - - Electrical Properties Max Rdc(m ) 4.00 Legend + Test frequency Preferred parts, the suggested choice for new designs,have shorter lead times and are more readily available. The column H(Oe) gives for each bead the calculated dc bias field in oersted for 1 turn and 1 ampere direct current. The actual dc H field in the application is this value of H times the actual NI (ampere-turn) product. For the effect of the dc bias on the impedance of the bead material, see figures 18-23 in the application note How to choose Ferrite Components for EMI Suppression. A ½ turn is defined as a single pass through a hole. l/A - Core Constant Ae : Effective Cross-Sectional Area L AL - Inductance Factor (__ N 2) N/AWG - Number of Turns/Wire Size for Test Coil l e : Effective Path Length Ve : Effective Core Volume Nl - Value of dc Ampere-turns Fair-Rite Product's Catalog Part Data Sheet, 2744051447 Printed: 2014-06-11 Fair-Rite Products Corp. PO Box J,One Commercial Row, Wallkill, NY 12589-0288 Phone: (888) 324-7748 www.fair-rite.com Fair-Rite Product's Catalog Part Data Sheet, 2744051446 Printed: 2014-06-11 Fair-Rite Products Corp. PO Box J,One Commercial Row, Wallkill, NY 12589-0288 Phone: (888) 324-7748 www.fair-rite.com Part Number: 2744051446 Description: 44 COMMON MODE SM BEAD Figure: 2 Preferred Part: Weight: 1.000 (g) Mechanical Specifications Land Patterns V Dim mm A B C D E F G H J K 4.50 6.65 12.00 2.50 3.00 - mm nominal inch tol inch misc. Max Max Max ±0.50 ±0.10 - 0.177 0.262 0.472 0.098 0.118 - Max Max Max - Electrical Specifications Typical Impedance ( ) 10 MHz 60 25 MHz+ 100 100 MHz+ 230 250 MHz _ 300 MHz 275 W X Y Z 1.000 0.040 5.000 0.197 3.000 0.118 ref 4.000 0.158 9.000 0.354 Winding Information Turns Wire 1st Wire 2nd Wire Tested Size Length Length - - - - Reel Information Tape Width Pitch Parts 7 '' Parts 13 '' Parts 14 '' mm mm Reel Reel Reel - - - - - Package Size Pkg Size (-) Connector Plate # Holes # Rows - - Electrical Properties Max Rdc(m ) 4.00 Legend + Test frequency Preferred parts, the suggested choice for new designs,have shorter lead times and are more readily available. The column H(Oe) gives for each bead the calculated dc bias field in oersted for 1 turn and 1 ampere direct current. The actual dc H field in the application is this value of H times the actual NI (ampere-turn) product. For the effect of the dc bias on the impedance of the bead material, see figures 18-23 in the application note How to choose Ferrite Components for EMI Suppression. A ½ turn is defined as a single pass through a hole. l/A - Core Constant Ae : Effective Cross-Sectional Area L AL - Inductance Factor (__ N 2) N/AWG - Number of Turns/Wire Size for Test Coil l e : Effective Path Length Ve : Effective Core Volume Nl - Value of dc Ampere-turns Fair-Rite Product's Catalog Part Data Sheet, 2744051446 Printed: 2014-06-11 Fair-Rite Products Corp. PO Box J,One Commercial Row, Wallkill, NY 12589-0288 Phone: (888) 324-7748 www.fair-rite.com Fair-Rite Product's Catalog Part Data Sheet, 2744065447 Printed: 2014-06-11 Fair-Rite Products Corp. PO Box J,One Commercial Row, Wallkill, NY 12589-0288 Phone: (888) 324-7748 www.fair-rite.com Part Number: 2744065447 Description: 44 COMMON MODE SM BEAD Figure: 2 Preferred Part: Weight: 1.800 (g) Mechanical Specifications Land Patterns V Dim mm A B C D E F G H J K 5.30 7.00 14.80 2.50 3.00 - mm nominal inch tol inch misc. Max Max Max ±0.50 ±0.10 - 0.209 0.275 0.582 0.098 0.118 - Max Max Max - Electrical Specifications Typical Impedance ( ) 10 MHz 95 25 MHz+ 145 100 MHz+ 255 250 MHz _ 300 MHz 315 W X Y Z 1.100 0.043 5.000 0.197 3.000 0.118 ref 6.800 0.268 11.800 0.465 Winding Information Turns Wire 1st Wire 2nd Wire Tested Size Length Length - - - - Reel Information Tape Width Pitch Parts 7 '' Parts 13 '' Parts 14 '' mm mm Reel Reel Reel 24 12 - 1000 - Package Size Pkg Size (-) Connector Plate # Holes # Rows - - Electrical Properties Max Rdc(m ) 4.10 Legend + Test frequency Preferred parts, the suggested choice for new designs,have shorter lead times and are more readily available. The column H(Oe) gives for each bead the calculated dc bias field in oersted for 1 turn and 1 ampere direct current. The actual dc H field in the application is this value of H times the actual NI (ampere-turn) product. For the effect of the dc bias on the impedance of the bead material, see figures 18-23 in the application note How to choose Ferrite Components for EMI Suppression. A ½ turn is defined as a single pass through a hole. l/A - Core Constant Ae : Effective Cross-Sectional Area L AL - Inductance Factor (__ N 2) N/AWG - Number of Turns/Wire Size for Test Coil l e : Effective Path Length Ve : Effective Core Volume Nl - Value of dc Ampere-turns Fair-Rite Product's Catalog Part Data Sheet, 2744065447 Printed: 2014-06-11 Fair-Rite Products Corp. PO Box J,One Commercial Row, Wallkill, NY 12589-0288 Phone: (888) 324-7748 www.fair-rite.com Fair-Rite Product's Catalog Part Data Sheet, 2744065446 Printed: 2014-06-11 Fair-Rite Products Corp. PO Box J,One Commercial Row, Wallkill, NY 12589-0288 Phone: (888) 324-7748 www.fair-rite.com Part Number: 2744065446 Description: 44 COMMON MODE SM BEAD Figure: 2 Preferred Part: Weight: 1.800 (g) Mechanical Specifications Land Patterns V Dim mm A B C D E F G H J K 5.30 7.00 14.80 2.50 3.00 - mm nominal inch tol inch misc. Max Max Max ±0.50 ±0.10 - 0.209 0.275 0.582 0.098 0.118 - Max Max Max - Electrical Specifications Typical Impedance ( ) 10 MHz 95 25 MHz+ 145 100 MHz+ 255 250 MHz _ 300 MHz 315 W X Y Z 1.100 0.043 5.000 0.197 3.000 0.118 ref 6.800 0.268 11.800 0.465 Winding Information Turns Wire 1st Wire 2nd Wire Tested Size Length Length - - - - Reel Information Tape Width Pitch Parts 7 '' Parts 13 '' Parts 14 '' mm mm Reel Reel Reel - - - - - Package Size Pkg Size (-) Connector Plate # Holes # Rows - - Electrical Properties Max Rdc(m ) 4.10 Legend + Test frequency Preferred parts, the suggested choice for new designs,have shorter lead times and are more readily available. The column H(Oe) gives for each bead the calculated dc bias field in oersted for 1 turn and 1 ampere direct current. The actual dc H field in the application is this value of H times the actual NI (ampere-turn) product. For the effect of the dc bias on the impedance of the bead material, see figures 18-23 in the application note How to choose Ferrite Components for EMI Suppression. A ½ turn is defined as a single pass through a hole. l/A - Core Constant Ae : Effective Cross-Sectional Area L AL - Inductance Factor (__ N 2) N/AWG - Number of Turns/Wire Size for Test Coil l e : Effective Path Length Ve : Effective Core Volume Nl - Value of dc Ampere-turns Fair-Rite Product's Catalog Part Data Sheet, 2744065446 Printed: 2014-06-11 Fair-Rite Products Corp. PO Box J,One Commercial Row, Wallkill, NY 12589-0288 Phone: (888) 324-7748 www.fair-rite.com