Texas Instruments Line Transformers for the (DMT) Chipset • Central office or remote applications • Suitable for 8mbps/800kbps ADSL applications • Designed to meet IEC-950 isolation and insulation requirements • Meets ANSI T1.413 Issue 2, Category 1&2, and ITU G.Lite standards • Designed to optimize performance with the TI TNETD3000C/P, TNET4000R, TNET5000 series chipsets • Designed to interface with line drivers THS6002, 6012, 6022, and line receiver THS6062 • UL94V-0 materials • ISO 9001 certified supplier • UL/BABT Safety Agency Approvals Specifications Schott P/N OCL +/5% mH Turns Ratio Chip:Line +/- 2% Leakage uH Max IWC Pf Max 33817 1.500 1:1.423 18.0 35 0.70 35625 1.500 1:1.423 18.0 35 32824 1.500 1:1.423 18.0 36539 1.500 1:1.423 33818 1.500 32828 Dielectric Strength Vrms Min Config / Schematic App Notes 4.00 1500* EP13 THD CP 5 0.80 2.70 1500** EP13 THD CP 6 35 0.70 4.00 1500* EP13 SMD CP 5 18.0 35 0.80 2.70 1500** EP13 SMD CP 6 1:1.95 15.0 35 0.55 2.00 1500** EP13 THD CO/CP 6 1.500 1:1.95 15.0 35 0.55 2.00 1500* EP13 SMD CO/CP 5 37039 1.500 1:1.95 15.0 35 0.75 1.80 1500** EP13 SMD CO/CP 6 36313 0.375 1:1:1:1 6.00 40 0.68 2.00 1500** EP10 SMD CO/CP 6 37513 0.400 1:1.92 7.50 40 1.10 0.5 1500 EP10 SMD CO 7 DCR Chip DCR Line Max Ohms Max Ohms Parts availability subject to Schott manufacturing schedules and leadtimes. Not all parts available from stock. Please contact us for more details and availability. The Adobe Acrobat Reader is required to view these linked documents. Electrical Specifications Test Criteria 1. These transformers are designed for operating within a temperature range of -40°C to +85°C. All electrical characteristics are reported for operating at 25°C. 2. Inductance is measured at 10 kHz, 0.1 Vrms, leakage inductance at 100 kHz, 0.1 Vrms. 3. */**Designed to meet UL 1950/EN60950 isolation and insulation requirements. (See notes 5 & 6 below) 4. For complete parameters of components listed above, request individual specification sheets. 5. 33817, 32824, 32828 have UL1950 approval at 120 Vrms, 200Vpk/s, and BABT EN60950 approval at 250 Vrms. 6. 33818, 35625,36539,36313,37039 have UL1950/EN60950/BABT approval at 250 Vrms and are recommended for new designs. 7. Safety Agency approval is pending. Recommended for new designs. All data is believed to be accurate at time of printing. Schott Corporation reserves the right to make changes without notification. “Schott” is a trade name of Schott Corporation. All other trademarks and trade names are the property of their respective holder. © 2001 Schott Corporation 1000 Parkers Lake Road, Wayzata, Minnesota 55391 U.S.A. Tel: + (952) 475-1173 Fax: + (952) 475-1786 Email: [email protected] Web: http://www.schottcorp.com .590 MAX (14.99) EP10 SMD REF: PWB LAYOUT 4 5 1 8 .080 (2.03) .500 MAX (12.70) inches (mm) .035 (0.89) .098 (2.50) Tape and Reel Carrier Tape Width = 32mm –.03m m .615–.010 (15.62) 1 8 3 2 6 7 4 5 Tray Parts per tray = 70 .008 (0.20) .435 MAX (11.05) LINE .098 (2.50) .492 –.006 (12.50) .024 (0.61) CHIP EP13 SMD REF PWB LAYOUT .670 –.010 (17.02) .063 (1.60) 5 6 1 10 .560 MAX (14.22) inches (mm) .035 (0.89) .098 (2.50) Tape and Reel Carrier Tape Width = 32mm –.03m m .710 18.03) 1 .008 (0.20) .500 MAX (12.70) LINE .606 – .006 (15.39) .098 –.010 (2.50) Tray Parts per tray = 78 10 CHIP 4 7 .028 (0.70) EP13 THD .560 MAX (14.22) 5 6 1 10 inches (mm) .560 MAX (14.22) Tray Parts per tray = 78 NOTCH PIN1 .500 MAX (12.70) .110 MIN (2.79) 1 10 LINE .400 –.010 (10.16) .100 –.010 (2.54) CHIP 4 7 .02 Sq. (0.51) All statements and technical information contained herein are believed to be accurate, but the accuracy and completeness thereof is not guaranteed. If any product is found to be defective, Schott Corporation’s (Seller) only obligation shall be to replace such quantity of the product proved to be defective. User shall determine the suitability of the product for the intended use, and user assumes all risk and liability whatsoever in connection herewith. Seller shall not be liable for any direct, consequential, or incidental loss or damage. Conditions not specifically stated herein shall be governed by established trade customs. Schott Corporation reserves the right to makes changes without notification. “Schott” is a trade name of Schott Corporation. All other trademarks and trade names are the property of their respective holder. ©2001 Schott Corporation Schott Corporation 1000 Parkers Lake Road Wayzata, Minnesota 55391 U.S.A. Tel: + (952) 475-1173 Fax: + (952) 475-1786 Email: [email protected] Web: http://www.schottcorp.com