® MDW1000 SERIES DC/DC CONVERTER 2W, DIP-Package FEATURES ►Industrial Standard DIP-16 Package ►Wide 2:1 Input Voltage Range ►Fully Regulated Output Voltage ►I/O Isolation 1500 VDC ►Operating Ambient Temp. Range -40°C to +80°C ►Overload and Short Circuit Protection ►Designed-in Conducted EMI meets EN55022 Class A & FCC Level A ►UL/cUL/IEC/EN 60950-1 Safety Approval PRODUCT OVERVIEW The MINMAX MDW1 series is a range of isolated 2W DC/DC converter modules featuring fully regulated output voltages and wide 2:1 input voltage ranges. The products come in a compact DIP-16 package with a low height of just 8.0 mm (0.31 inch). An excellent efficiency allows an operating temperature range of –40°C to +80°C. These DC/DC converters offer an economical solution for many cost critical applications in battery-powered equipment and instrumentation. Model Selection Guide Model Number MDW1011 MDW1012 MDW1013 MDW1014 MDW1015 MDW1016 MDW1017 MDW1021 MDW1022 MDW1023 MDW1024 MDW1025 MDW1026 MDW1027 MDW1031 MDW1032 MDW1033 MDW1034 MDW1035 MDW1036 MDW1037 MDW1041 MDW1042 MDW1043 MDW1044 MDW1045 MDW1046 MDW1047 Input Voltage (Range) VDC Output Voltage VDC 3.3 5 12 15 ±5 ±12 ±15 3.3 5 12 15 ±5 ±12 ±15 3.3 5 12 15 ±5 ±12 ±15 3.3 5 12 15 ±5 ±12 ±15 5 (4.5 ~ 9) 12 (9 ~ 18) 24 (18 ~ 36) 48 (36 ~ 75) E-mail:[email protected] 2015/07/31 REV:8 Output Current Max. mA 500 400 167 134 ±200 ±83 ±67 500 400 167 134 ±200 ±83 ±67 500 400 167 134 ±200 ±83 ±67 500 400 167 134 ±200 ±83 ±67 Tel:886-6-2923150 Page 1 of 4 Min. mA 125 100 42 33 ±50 ±21 ±17 125 100 42 33 ±50 ±21 ±17 125 100 42 33 ±50 ±21 ±17 125 100 42 33 ±50 ±21 ±17 Input Current @Max. Load mA(typ.) 471 548 534 582 667 615 598 184 217 209 220 242 224 226 96 109 109 108 119 112 110 49 57 53 55 62 57 57 @No Load mA(typ.) Reflected Ripple Current mA(typ.) 40 100 20 25 10 15 8 10 Max. capacitive Load μF 2200 1000 170 110 470# 100# 47# 2200 1000 170 110 470# 100# 47# 2200 1000 170 110 470# 100# 47# 2200 1000 170 110 470# 100# 47# # For each output Efficiency (typ.) @Max. Load % 70 73 75 73 64 69 71 73 77 80 80 73 78 78 72 77 80 81 74 78 80 71 73 79 79 71 77 77 ® MDW1000 SERIES DC/DC CONVERTER 2W, DIP-Package Input Specifications Parameter Input Surge Voltage (1 sec. max.) Start-Up Voltage Under Voltage Shutdown Model Min. Typ. 5V Input Models -0.7 --- Max. 11 12V Input Models -0.7 --- 25 24V Input Models -0.7 --- 50 48V Input Models 5V Input Models 12V Input Models 24V Input Models 48V Input Models 5V Input Models 12V Input Models 24V Input Models 48V Input Models -0.7 3.5 4.5 8 16 ----------- --4 7 12 24 3.5 6.5 11 22 --- 100 Short Circuit Input Power All Models Input Filter 4.5 9 18 36 4 8.5 17 34 1500 Unit VDC mW Internal Pi Type Compliance to EN 55022,class A and FCC part 15,class A Conducted EMI Output Specifications Parameter Conditions Output Voltage Setting Accuracy Min. Typ. Max. Unit --- --- ±2.0 %Vnom. % Output Voltage Balance Dual Output, Balanced Loads Line Regulation Vin=Min. to Max. @Full Load ----- ±1.0 ±0.3 ±2.0 ±0.5 Load Regulation Io=25% to 100% --- ±0.5 ±0.75 % Ripple & Noise 0-20 MHz Bandwidth --- 30 50 mV P-P --- 100 300 μsec Transient Recovery Time 25% Load Step Change Transient Response Deviation % --- ±3 ±5 % Temperature Coefficient --- ±0.01 ±0.02 %/℃ Short Circuit Protection Continuous, Automatic Recovery General Specifications Parameter I/O Isolation Voltage Conditions Min. Typ. Max. Unit 60 Seconds 1500 --- --- VDC 1 Second 1800 --- --- VDC I/O Isolation Resistance 500 VDC 1000 --- --- MΩ I/O Isolation Capacitance 100KHz, 1V --- 250 420 pF --- 300 --- KHz Switching Frequency MTBF (calculated) MIL-HDBK-217F@25℃, Ground Benign Safety Approvals 1,000,000 Hours UL/cUL 60950-1 recognition(CSA certificate), IEC/EN 60950-1(CB-report) Environmental Specifications Parameter Operating Ambient Temperature Range (See Power Derating Curve) Conditions Min. Max. Unit Natural Convection -40 +80 ℃ Case Temperature --- +90 ℃ Storage Temperature Range -55 --- +105 95 ℃ % rel. H 260 ℃ Humidity (non condensing) Cooling Natural Convection Lead Temperature (1.5mm from case for 10Sec.) E-mail:[email protected] 2015/07/31 REV:8 Tel:886-6-2923150 Page 2 of 4 --- ® MDW1000 SERIES DC/DC CONVERTER 2W, DIP-Package Power Derating Curve 100 Natural Convection 20LFM Output Power (%) 80 400LFM 60 40 20 0 ~ -40 0 20 40 60 80 100 110 Ambient Temperature C Notes 1 Specifications typical at Ta=+25℃, resistive load, nominal input voltage and rated output current unless otherwise noted. 2 Transient recovery time is measured to within 1% error band for a step change in output load of 75% to 100%. 3 4 These power converters require a minimum output loading to maintain specified regulation, operation under no-load conditions will not damage these modules; however, they may meet allbyspecifications listed.in the input supply line. We recommend to protect thenot converter a slow blow fuse 5 Other input and output voltage may be available, please contact factory. 6 That “natural convection” is about 20LFM but is not equal to still air (0 LFM). 7 Specifications are subject to change without notice. Package Specifications 3.8 8.0 [0.31] Pin Connections Pin Single Output 1 -Vin 7 NC 8 NC 9 +Vout 10 -Vout 16 +Vin [0.15] 0.5 [0.02] Mechanical Dimensions 0.50 [0.02] Dual Output -Vin NC Common +Vout -Vout +Vin NC: No Connection 8 10 9 16 3.0 [0.12] 15.24 [0.60] 2.54 [0.10] 23.8 [0.94] 13.7 [0.54] Bottom View 1.77 10.16 [0.40] 7 [0.07] 1 Physical Characteristics Case Size : 23.8x13.7x8.0 mm (0.94x0.54x0.31 inches) Case Material : Non-Conductive Black Plastic (flammability to UL 94V-0 rated) Pin Material : Phosphor bronze Weight : 5.1g E-mail:[email protected] 2015/07/31 REV:8 Tel:886-6-2923150 Page 3 of 4 ►All dimensions in mm (inches) ►Tolerance: X.X±0.25 (X.XX±0.01) X.XX±0.13 ( X.XXX±0.005) ►Pin diameter 0.5 ±0.05 (0.02±0.002) ® MDW1000 SERIES DC/DC CONVERTER 2W, DIP-Package Test Setup Input Reflected-Ripple Current Test Setup Input reflected-ripple current is measured with a inductor Lin (4.7μH) and Cin (220μF, ESR < 1.0Ω at 100 KHz) to simulate source impedance. Capacitor Cin, offsets possible battery impedance. Current ripple is measured at the input terminals of the module, measurement bandwidth is 0-500 KHz. To Oscilloscope + + Battery +Vin Lin Current Probe Cin +Out DC / DC Converter -Vin Load -Out Peak-to-Peak Output Noise Measurement Test Use a Cout 0.47μF ceramic capacitor. Scope measurement should be made by using a BNC socket, measurement bandwidth is 0-20 MHz. Position the load between 50 mm and 75 mm from the DC/DC Converter. +Vin +Out Copper Strip Single Output DC / DC Converter -Vin Cout -Out Scope Resistive Load Copper Strip +Vin +Out Copper Strip Dual Output DC / DC Converter Com. Copper Strip -Vin -Out Copper Strip Scope Cout Cout Resistive Load Scope Technical Notes Maximum Capacitive Load The MDW1000 series has limitation of maximum connected capacitance on the output. The power module may operate in current limiting mode during start-up, affecting the ramp-up and the startup time. The maximum capacitance can be found in the data sheet. Overcurrent Protection To provide protection in a fault (output overload) condition, the unit is equipped with internal current limiting circuitry and can endure current limiting for an unlimited duration. At the point of current-limit inception, the unit shifts from voltage control to current control. The unit operates normally once the output current is brought back into its specified range. Input Source Impedance The power module should be connected to a low ac-impedance input source. Highly inductive source impedances can affect the stability of the power module. In applications where power is supplied over long lines and output loading is high, it may be necessary to use a capacitor on the input to insure startup. By using a good quality low Equivalent Series Resistance (ESR < 1.0Ω at 100 kHz) capacitor of a 8.2uF for the 5V input devices, a 3.3μF for the 12V input devices and a 1.5μF for the 24V and 48V devices, capacitor mounted close to the power module helps ensure stability of the unit. + DC Power Source +Vin + +Out DC / DC Converter Load Cin - -Vin -Out Output Ripple Reduction A good quality low ESR capacitor placed as close as practicable across the load will give the best ripple and noise performance. recommended to use 3.3μF capacitors at the output. + +Vin - +Out Single Output DC / DC Converter DC Power Source -Vin + Cout Load -Out +Vin - +Out Dual Output DC / DC Com. Converter DC Power Source To reduce output ripple, it is -Vin -Out Cout Load Load Cout Thermal Considerations Many conditions affect the thermal performance of the power module, such as orientation, airflow over the module and board spacing. To avoid exceeding the maximum temperature rating of the components inside the power module, the case temperature must be kept below 90℃. The derating curves are determined from measurements obtained in a test setup. Position of air velocity probe and thermocouple 15mm / 0.6in 50mm / 2in Air Flow DUT 18, Sin Sin Road, An-Ping Industrial District, Tainan 702, Taiwan Tel: 886-6-2923150 Fax: 886-6-2923149 E-mail: [email protected] Minmax Technology Co., Ltd. 2015/07/31 REV:8 Page 4 of 4