® MIW3100 SERIES DC/DC CONVERTER 6W, DIP-Package FEATURES ►DIP-24 Plastic Package ►Wide 2:1 Input Range ►High Efficiency up to 86% ►Operating Ambient Temp. Range –40°C to +85°C ►Short Circuit Protection ►I/O-isolation 1500VDC ►Cost optimized Design PRODUCT OVERVIEW The MINMAX MIW3100 series is a range of isolated 6W DC/DC converter modules featuring fully regulated output voltages and wide 2:1 input voltage ranges. The product comes in a DIP-24 plastic package with industry standard pinout. An excellent efficiency allows an operating temperature range of –40°C to +85°C.These DC/DC converters offer an economical solution for many cost critical applications in battery-powered equipment and instrumentation. Model Selection Guide Model Input Output Output Number Voltage Voltage Current (Range) VDC MIW3121 MIW3122 MIW3123 MIW3126 MIW3127 MIW3131 MIW3132 MIW3133 MIW3136 MIW3137 12 (9 ~ 18) 24 (18 ~ 36) VDC 3.3 5 12 ±12 ±15 3.3 5 12 ±12 ±15 Input Current Reflected Max. capacitive Ripple Load Max. Min. @Max. Load @No Load Current mA 1200 1000 500 ±250 ±200 1200 1000 500 ±250 ±200 mA 60 50 25 ±12.5 ±10 60 50 25 ±12.5 ±10 mA(typ.) 429 514 595 595 595 209 251 291 291 291 mA(typ.) mA(typ.) 20 25 (typ.) @Max. Load uF 6800 1000# 6800 5 Efficiency 15 1000# % 77 81 84 84 84 79 83 86 86 86 # For each output Input Specifications Parameter Model 12V Input Models 24V Input Models 12V Input Models 24V Input Models 12V Input Models 24V Input Models Input Surge Voltage (1 sec. max.) Start-Up Voltage Under Voltage Shutdown Reverse Polarity Input Current Short Circuit Input Power Internal Power Dissipation Input Filter Conducted EMI (with suffix A only) E-mail:[email protected] 2015/07/31 REV:3 All Models Tel:886-6-2923150 Page 1 of 4 Min. -0.7 -0.7 Typ. Max. Unit 25 --50 --4.5 6 8 VDC 8 12 16 ----8 ----16 ----1 A --1000 3000 mW ----2500 mW Internal Pi Type Compliance to EN 55022,class A and FCC part 15,class A ® MIW3100 SERIES DC/DC CONVERTER 6W, DIP-Package Output Specifications Parameter Output Voltage Setting Accuracy Output Voltage Balance Line Regulation Load Regulation Ripple & Noise Transient Recovery Time Transient Response Deviation Temperature Coefficient Over Current Protection Short Circuit Protection Conditions Dual Output, Balanced Loads Vin=Min. to Max. @Full Load Io=20% to 100% 0-20 MHz Bandwidth 25% Load Step Change Foldback Min. Typ. --±0.5 --±0.5 --±0.1 --±0.3 --50 --150 --±2 --±0.01 120 150 Continuous, Automatic Recovery Max. ±1.0 ±2.0 ±0.3 ±1.0 75 300 ±6 ±0.02 --- Unit %Vnom. % % % mV P-P uS % %/℃ % General Specifications Parameter I/O Isolation Voltage Conditions Min. Typ. Max. Unit 60 Seconds 1500 --- --- VDC 1 Seconds 1800 --- --- VDC I/O Isolation Resistance 500 VDC 1000 --- --- MΩ I/O Isolation Capacitance 100KHz, 1V --- 380 500 pF 300 --- Switching Frequency --- MTBF (calculated) MIL-HDBK-217F@25℃, Ground Benign Safety Approvals 1,000,000 KHz Hours UL/cUL 60950-1 recognition(CSA certificate), IEC/EN 60950-1(CB-scheme) Environmental Specifications Parameter Operating Ambient Temperature Range (See Power Derating Curve) Conditions Min. Max. Unit Natural Convection -40 +85 ℃ ℃ Case Temperature --- +90 Storage Temperature Range -50 +125 ℃ Humidity (non condensing) --- 95 % rel. H 260 ℃ Cooling Natural Convection Lead Temperature --- (1.5mm from case for 10Sec.) Output Power (%) Power Derating Curve E-mail:[email protected] 2015/07/31 REV:3 Tel:886-6-2923150 Page 2 of 4 ® MIW3100 SERIES DC/DC CONVERTER 6W, DIP-Package Notes 1 Specifications typical at Ta=+25℃, resistive load, nominal input voltage and rated output current unless otherwise noted. 2 Transient recovery time is measured to within 1% error band for a step change in output load of 75% to 100%. 3 These power converters require a minimum output loading to maintain specified regulation, operation under no-load conditions will not damage these modules; 4 We recommend to protect the converter by a slow blow fuse in the input supply line. 5 Other input and output voltage may be available, please contact factory. 6 Specifications are subject to change without notice. however they may not meet all specifications listed. Package Specifications Pin Connections 3 9 11 Bottom View 23 22 16 15.24 [0.60] 2.54 [0.10] 31.8 [1.25] Single Output Dual Output 2 -Vin -Vin 3 -Vin -Vin 9 No Pin Common 11 NC -Vout 14 +Vout +Vout 16 -Vout Common 22 +Vin +Vin 23 +Vin +Vin NC: No Connection 14 5.08 4.5 [0.20][0.18] 2.54 [0.10] 2 Pin 20.3 [0.80] 0.50 [0.02] 15.22 [0.60] 4.1 [0.16] 10.2 [0.40] Mechanical Dimensions ►All dimensions in mm (inches) ►Tolerance: X.X±0.25 (X.XX±0.01) X.XX±0.13 ( X.XXX±0.005) ►Pin diameter 0.5 ±0.05 (0.02±0.002) Physical Characteristics ase Size : 31.8x20.3x10.2mm (1.25x0.80x0.40 Inches) Case Material : Non-Conductive Black Plastic (flammability to UL 94V-0 rated) Weight : 16.9g Order Code Table Standard With EMI MIW3121 MIW3121A MIW3122 MIW3122A MIW3123 MIW3123A MIW3126 MIW3126A MIW3127 MIW3127A MIW3131 MIW3131A MIW3132 MIW3132A MIW3133 MIW3133A MIW3136 MIW3136A MIW3137 MIW3137A E-mail:[email protected] 2015/07/31 REV:3 Tel:886-6-2923150 Page 3 of 4 ® MIW3100 SERIES DC/DC CONVERTER 6W, DIP-Package Test Configurations Input Reflected-Ripple Current Test Setup Input reflected-ripple current is measured with a inductor Lin (4.7uH) and Cin (220uF, ESR < 1.0Ω at 100 KHz) to simulate source impedance. Capacitor Cin, offsets possible battery impedance. Current ripple is measured at the input terminals of the module, measurement bandwidth is 0-500 KHz. To Oscilloscope + + Battery +Vin Lin DC / DC Converter Current Probe Cin +Out -Vin Load -Out Peak-to-Peak Output Noise Measurement Test Use a Cout 0.47uF ceramic capacitor. Scope measurement should be made by using a BNC socket, measurement bandwidth is 0-20 MHz. Position the load between 50 mm and 75 mm from the DC/DC Converter. +Vin +Out Copper Strip Single Output DC / DC Converter -Vin Cout -Out Scope Resistive Load Copper Strip +Vin +Out Copper Strip Dual Output DC / DC Converter Com. Copper Strip -Vin -Out Scope Cout Resistive Load Cout Scope Copper Strip Design & Feature Considerations Overcurrent Protection To provide protection in a fault (output overload) condition, the unit is equipped with internal current limiting circuitry and can endure current limiting for an unlimited duration. At the point of current-limit inception, the unit shifts from voltage control to current control. The unit operates normally once the output current is brought back into its specified range. Input Source Impedance The power module should be connected to a low ac-impedance input source. Highly inductive source impedances can affect the stability of the power module. In applications where power is supplied over long lines and output loading is high, it may be necessary to use a capacitor at the input to ensure startup. Capacitor mounted close to the power module helps ensure stability of the unit, it is recommended to use a good quality low Equivalent Series Resistance (ESR < 1.0Ω at 100 KHz) capacitor of a 3.3uF for the 12V input devices and a 2.2uF for the 24V devices. + DC Power Source +Vin + +Out DC / DC Converter Load Cin - -Vin -Out Output Ripple Reduction A good quality low ESR capacitor placed as close as practicable across the load will give the best ripple and noise performance. To reduce output ripple, it is recommended to use 3.3uF capacitors at the output. + +Vin DC Power Source - +Out Single Output DC / DC Converter -Vin + Cout Load -Out +Vin DC Power Source - +Out Dual Output DC / DC Com. Converter -Vin -Out Cout Load Load Cout Maximum Capacitive Load MIW3100 series have limitation of maximum connected capacitance at the output. The power module may be operated in current limiting mode during start-up, affecting the ramp-up and the startup time. For optimum performance we recommend 1000uF maximum capacitive load for dual outputs and 6800uF capacitive load for single outputs. The maximum capacitance can be found in the data sheet. Thermal Considerations Many conditions affect the thermal performance of the power module, such as orientation, airflow over the module and board spacing. To avoid exceeding the maximum temperature rating of the components inside the power module, the case temperature must be kept below 90℃. The derating curves are determined from measurements obtained in a test setup. Position of air velocity probe and thermocouple 15mm / 0.6in 50mm / 2in Air Flow DUT 18, Sin Sin Road, An-Ping Industrial District, Tainan 702, Taiwan Tel: 886-6-2923150 Fax: 886-6-2923149 E-mail: [email protected] Minmax Technology Co., Ltd. 2015/07/31 REV:3 Page 4 of 4