PreliminaryData Sheet 2SC3356 R09DS0021EJ0300 Rev.3.00 NPN Silicon RF Transistor Jun 28, 2011 NPN Epitaxial Silicon RF Transistor for Microwave Low-Noise Amplification 3-pin Minimold FEATURES • Low noise and high gain : NF = 1.1 dB TYP., Ga = 11 dB TYP. @ VCE = 10 V, IC = 7 mA, f = 1 GHz • High power gain : MAG = 13 dB TYP. @ VCE = 10 V, IC = 20 mA, f = 1 GHz <R> ORDERING INFORMATION Part Number 2SC3356 Order Number 2SC3356-A 2SC3356-T1B 2SC3356-T1B-A Package 3-pin Minimold (Pb-Free) Quantity Supplying Form 50 pcs (Non reel) • 8 mm wide embossed taping 3 kpcs/reel • Pin 3 (Collector) face the perforation side of the tape Remark To order evaluation samples, please contact your nearby sales office. The unit sample quantity is 50 pcs. ABSOLUTE MAXIMUM RATINGS (TA = +25°C) Parameter Symbol Ratings Unit Collector to Base Voltage VCBO 20 V Collector to Emitter Voltage VCEO 12 V Emitter to Base Voltage VEBO 3.0 V IC 100 mA 200 mW Collector Current Total Power Dissipation Ptot Note Junction Temperature Tj 150 °C Storage Temperature Tstg −65 to +150 °C Note Free air CAUTION Observe precautions when handling because these devices are sensitive to electrostatic discharge. The mark <R> shows major revised points. The revised points can be easily searched by copying an "<R>" in the PDF file and specifying it in the "Find what:" field. R09DS0021EJ0300 Rev.3.00 Jun 28, 2011 Page 1 of 7 2SC3356 ELECTRICAL CHARACTERISTICS (TA = +25°C) Parameter Symbol Test Conditions MIN. TYP. MAX. Unit DC Characteristics Collector Cut-off Current ICBO VCB = 10 V, IE = 0 – – 1.0 μA Emitter Cut-off Current IEBO VEB = 1.0 V, IC = 0 – – 1.0 μA VCE = 10 V, IC = 20 mA 50 120 250 – VCE = 10 V, IC = 20 mA – 7 – GHz ⏐S21e⏐ VCE = 10 V, IC = 20 mA, f = 1 GHz – 11.5 – dB NF VCE = 10 V, IC = 7 mA, f = 1 GHz – 1.1 2.0 dB VCB = 10 V, IE = 0, f = 1 MHz − 0.55 1.0 pF DC Current Gain hFE Note 1 RF Characteristics Gain Bandwidth Product fT 2 Insertion Power Gain Noise Figure Reverse Transfer Capacitance Cre Note 2 Notes 1. Pulse measurement: PW ≤ 350 μs, Duty Cycle ≤ 2% 2. Collector to base capacitance when the emitter grounded <R> hFE CLASSIFICATION Rank Q/YQ R/YR S/YS Marking R23 R24 R25 hFE Value 50 to 100 80 to 160 125 to 250 R09DS0021EJ0300 Rev.3.00 Jun 28, 2011 Page 2 of 7 2SC3356 TYPICAL CHARACTERISTICS (TA = +25°C, unless otherwise specified) TOTAL POWER DISSIPATION vs. AMBIENT TEMPERATURE REVERSE TRANSFER CAPACITANCE vs. COLLECTOR TO BASE VOLTAGE Reverse Transfer Capacitance Cre (pF) Total Power Dissipation Ptot (mW) 250 Free air 200 150 100 50 0 25 50 75 100 125 150 1 0.5 0.3 0.2 0.5 1 2 5 10 20 30 Collector to Base Voltage VCB (V) DC CURRENT GAIN vs. COLLECTOR CURRENT GAIN BANDWIDTH PRODUCT vs. COLLECTOR CURRENT 10 Gain Bandwidth Product fT (GHz) VCE = 10 V 100 50 20 10 0.5 1 5 10 VCE = 10 V 5 2 1 0.5 0.2 0.1 0.1 50 0.5 1 5 10 50 100 Collector Current IC (mA) Collector Current IC (mA) INSERTION POWER GAIN, MAG vs. FREQUENCY INSERTION POWER GAIN vs. COLLECTOR CURRENT 25 15 Insertion Power Gain |S21e|2 (dB) DC Current Gain hFE f = 1 MHz Ambient Temperature TA (˚C) 200 Insertion Power Gain |S21e|2 (dB) Maximum Available Power Gain MAG (dB) 2 MAG 20 |S21e|2 15 10 5 VCE = 10 V IC = 20 mA 0 0.05 0.1 0.2 0.5 1 2 Frequency f (GHz) VCE = 10 V f = 1 GHz 10 5 0 0.5 1 5 10 50 70 Collector Current IC (mA) Remark The graphs indicate nominal characteristics. R09DS0021EJ0300 Rev.3.00 Jun 28, 2011 Page 3 of 7 2SC3356 NOISE FIGURE vs. COLLECTOR CURRENT f = 1 GHz IC = 20 mA Noise Figure NF (dB) Noise Figure NF (dB) 6 5 4 3 2 15 5 VCE = 10 V f = 1 GHz 4 12 |S21e|2 3 9 2 6 NF 1 3 1 0 0.5 1 5 10 50 70 Collector Current IC (mA) 0 2 4 6 8 Insertion Power Gain |S21e|2 (dB) 7 NOISE FIGURE, INSERTION POWER GAIN vs. COLLECTOR TO EMITTER VOLTAGE 0 10 Collector to Emitter Voltage VCE (V) Remark The graphs indicate nominal characteristics. R09DS0021EJ0300 Rev.3.00 Jun 28, 2011 Page 4 of 7 2SC3356 SMITH CHART S11e, S22e-FREQUENCY CONDITION : VCE = 10 V, 200 MHz Step 1.4 1.2 1.6 0.7 0.6 0.1 0.3 7 3 1.8 2 .0 T EN 0.4 4 0. 0 3. 30 C 0.6 O 0.8 0 1. 6.0 0.6 10 0.4 0.1 20 10 5.0 4.0 3.0 1.8 2.0 1.6 1.4 0.7 0.8 0.6 0.5 0.4 0.3 1.2 2.0 GHz IC = 20 mA 50 0.9 1.0 ) 10 IC = 5 mA 0.2 GHz 8 0. 0 IC = 20 mA 1. 5.0 1.0 E NC TA X AC −J––O– RE –Z ) 4.0 ( 0.8 0 0.6 IC = 5 mA NE G 5 0.4 2.0 1.8 1.6 1.4 0.35 0.15 −70 1.2 4 0.3 6 0.1 0.2 0.36 0.14 −80 1.0 0 0.8 3 0.3 7 −6 0.9 0.1 0.7 32 18 0. 0. 0 0. −5 0.6 0. 3 −4 0.1 1 0 9 E IV AT 3. 0.2 GHz 0.3 0.2 0 0 0.38 0.39 0.12 0.11 −100 −90 0.37 0.13 0 −11 0.40 0.10 0. 4 0. 3 0 −1 7 30 0.4 0.0 2 8 0 −1 2 0.4 1 0.0 9 4 0. 0.27 0.2 0 .2 8 3 0 0 .2 .29 2 −20 0.2 1 −3 0 S22e 0.6 0.2 −10 0.4 0.26 0.24 20 ( 50 0 REACTANCE COMPONENT R –––– 0.2 ZO 0.25 0.25 0.2 20 0.2 0.3 0.2 0.8 S11e 0.24 0.23 0.26 2 0.2 0.27 8 10 0.2 20 4.0 0 1. 2.0 GHz 1 0.2 9 0.2 ( –Z–+–J–XTANCE CO ) MPO N 0. 5 0. 18 32 0. 50 0 0.2 0 0.3 WAVELE N 60 40 GTHS 0 0.01 0.49 0.02 TOWARD 0.48 0 0.49 0.0 GENE 0.01 7 0.48 3 RA 0.4 0.0W2ARD LOADLECTION COEF FCIENT 0.4 0.0TOR 3 HS TO LE OF REF 6 I 7 .0 N DEG 0NGT ANG 4 0.4 REE 0 E 0.4 6 L 0 S .0W4AVE −1 6 0.0 0 5 15 0 0.4 5 0.4 5 0 15 0 − . 5 0 0. 4 0 4 POS 0.1 14 0.4 6 0. 06 ENT ITIV 40 ON 0 ER 4 MP 0. −1 E O A C 0.1 6 0.3 4 70 0.2 0.1 0.3 0.15 0.35 19 0. 31 0. 2 0.4 20 1 07 0. 3 4 0. 0 13 1.0 0 0.14 0.36 80 90 0.9 .08 0.13 0.37 0.12 0.38 0.11 0.39 100 0.10 0.40 110 0.8 9 0.0 1 0.4 S21e-FREQUENCY S12e-FREQUENCY CONDITION : VCE = 10 V, IC = 20 mA CONDITION : VCE = 10 V, IC = 20 mA 90˚ 90˚ 120˚ 2.0 GHz 60˚ 120˚ 60˚ 0.2 GHz S12e 150˚ 30˚ S21e 150˚ 30˚ 0.2 GHz 180˚ 2.0 GHz 5 10 15 –150˚ 20 0˚ 180˚ –30˚ –60˚ –120˚ –90˚ R09DS0021EJ0300 Rev.3.00 Jun 28, 2011 0.05 0.1 0.15 –150˚ 0.2 0.25 0˚ –30˚ –60˚ –120˚ –90˚ Page 5 of 7 2SC3356 S-PARAMETERS S-parameters and noise parameters are provided on our Web site in a format (S2P) that enables the direct import of the parameters to microwave circuit simulators without the need for keyboard inputs. Click here to download S-parameters. [RF and Microwave] → [Device Parameters] URL http://www2.renesas.com/microwave/en/download.html R09DS0021EJ0300 Rev.3.00 Jun 28, 2011 Page 6 of 7 2SC3356 PACKAGE DIMENSIONS 3-PIN MINIMOLD (UNIT: mm) 0.65+0.1 –0.15 1 3 0.4+0.1 –0.05 0.95 2 0.95 1.5 Marking 0 to 0.1 1.1 to 1.4 0.16+0.1 –0.05 0.3 2.9±0.2 0.4+0.1 –0.05 2.8±0.2 PIN CONNECTIONS 1. Emitter 2. Base 3. Collector R09DS0021EJ0300 Rev.3.00 Jun 28, 2011 Page 7 of 7 Revision History Rev. − 3.00 Date Jun 2004 Jun 28, 2011 2SC3356 Data Sheet Description Summary Page − p.1 p.2 Previous No. :PU10209EJ02V0DS Modification of ORDERING INFORMATION Modification of hFE CLASSIFICATION All trademarks and registered trademarks are the property of their respective owners. C-1 Notice 1. All information included in this document is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas Electronics products listed herein, please confirm the latest product information with a Renesas Electronics sales office. Also, please pay regular and careful attention to additional and different information to be disclosed by Renesas Electronics such as that disclosed through our website. 2. Renesas Electronics does not assume any liability for infringement of patents, copyrights, or other intellectual property rights of third parties by or arising from the use of Renesas Electronics products or technical information described in this document. No license, express, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights of Renesas Electronics or others. 3. You should not alter, modify, copy, or otherwise misappropriate any Renesas Electronics product, whether in whole or in part. 4. Descriptions of circuits, software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples. You are fully responsible for the incorporation of these circuits, software, and information in the design of your equipment. Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the use of these circuits, software, or information. 5. When exporting the products or technology described in this document, you should comply with the applicable export control laws and regulations and follow the procedures required by such laws and regulations. You should not use Renesas Electronics products or the technology described in this document for any purpose relating to military applications or use by the military, including but not limited to the development of weapons of mass destruction. Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable domestic or foreign laws or regulations. 6. Renesas Electronics has used reasonable care in preparing the information included in this document, but Renesas Electronics does not warrant that such information is error free. Renesas Electronics 7. Renesas Electronics products are classified according to the following three quality grades: "Standard", "High Quality", and "Specific". The recommended applications for each Renesas Electronics product assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein. depends on the product's quality grade, as indicated below. You must check the quality grade of each Renesas Electronics product before using it in a particular application. You may not use any Renesas Electronics product for any application categorized as "Specific" without the prior written consent of Renesas Electronics. Further, you may not use any Renesas Electronics product for any application for which it is not intended without the prior written consent of Renesas Electronics. Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for an application categorized as "Specific" or for which the product is not intended where you have failed to obtain the prior written consent of Renesas Electronics. The quality grade of each Renesas Electronics product is "Standard" unless otherwise expressly specified in a Renesas Electronics data sheets or data books, etc. "Standard": Computers; office equipment; communications equipment; test and measurement equipment; audio and visual equipment; home electronic appliances; machine tools; personal electronic equipment; and industrial robots. "High Quality": Transportation equipment (automobiles, trains, ships, etc.); traffic control systems; anti-disaster systems; anti-crime systems; safety equipment; and medical equipment not specifically designed for life support. "Specific": Aircraft; aerospace equipment; submersible repeaters; nuclear reactor control systems; medical equipment or systems for life support (e.g. artificial life support devices or systems), surgical implantations, or healthcare intervention (e.g. excision, etc.), and any other applications or purposes that pose a direct threat to human life. 8. You should use the Renesas Electronics products described in this document within the range specified by Renesas Electronics, especially with respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. Renesas Electronics shall have no liability for malfunctions or damages arising out of the use of Renesas Electronics products beyond such specified ranges. 9. Although Renesas Electronics endeavors to improve the quality and reliability of its products, semiconductor products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. Further, Renesas Electronics products are not subject to radiation resistance design. Please be sure to implement safety measures to guard them against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas Electronics product, such as safety design for hardware and software including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. Because the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or system manufactured by you. 10. Please contact a Renesas Electronics sales office for details as to environmental matters such as the environmental compatibility of each Renesas Electronics product. Please use Renesas Electronics products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. Renesas Electronics assumes no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations. 11. This document may not be reproduced or duplicated, in any form, in whole or in part, without prior written consent of Renesas Electronics. 12. Please contact a Renesas Electronics sales office if you have any questions regarding the information contained in this document or Renesas Electronics products, or if you have any other inquiries. (Note 1) "Renesas Electronics" as used in this document means Renesas Electronics Corporation and also includes its majority-owned subsidiaries. (Note 2) "Renesas Electronics product(s)" means any product developed or manufactured by or for Renesas Electronics. http://www.renesas.com SALES OFFICES Refer to "http://www.renesas.com/" for the latest and detailed information. Renesas Electronics America Inc. 2880 Scott Boulevard Santa Clara, CA 95050-2554, U.S.A. Tel: +1-408-588-6000, Fax: +1-408-588-6130 Renesas Electronics Canada Limited 1101 Nicholson Road, Newmarket, Ontario L3Y 9C3, Canada Tel: +1-905-898-5441, Fax: +1-905-898-3220 Renesas Electronics Europe Limited Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K Tel: +44-1628-585-100, Fax: +44-1628-585-900 Renesas Electronics Europe GmbH Arcadiastrasse 10, 40472 Düsseldorf, Germany Tel: +49-211-65030, Fax: +49-211-6503-1327 Renesas Electronics (China) Co., Ltd. 7th Floor, Quantum Plaza, No.27 ZhiChunLu Haidian District, Beijing 100083, P.R.China Tel: +86-10-8235-1155, Fax: +86-10-8235-7679 Renesas Electronics (Shanghai) Co., Ltd. Unit 204, 205, AZIA Center, No.1233 Lujiazui Ring Rd., Pudong District, Shanghai 200120, China Tel: +86-21-5877-1818, Fax: +86-21-6887-7858 / -7898 Renesas Electronics Hong Kong Limited Unit 1601-1613, 16/F., Tower 2, Grand Century Place, 193 Prince Edward Road West, Mongkok, Kowloon, Hong Kong Tel: +852-2886-9318, Fax: +852 2886-9022/9044 Renesas Electronics Taiwan Co., Ltd. 13F, No. 363, Fu Shing North Road, Taipei, Taiwan Tel: +886-2-8175-9600, Fax: +886 2-8175-9670 Renesas Electronics Singapore Pte. Ltd. 1 harbourFront Avenue, #06-10, keppel Bay Tower, Singapore 098632 Tel: +65-6213-0200, Fax: +65-6278-8001 Renesas Electronics Malaysia Sdn.Bhd. Unit 906, Block B, Menara Amcorp, Amcorp Trade Centre, No. 18, Jln Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia Tel: +60-3-7955-9390, Fax: +60-3-7955-9510 Renesas Electronics Korea Co., Ltd. 11F., Samik Lavied' or Bldg., 720-2 Yeoksam-Dong, Kangnam-Ku, Seoul 135-080, Korea Tel: +82-2-558-3737, Fax: +82-2-558-5141 © 2011 Renesas Electronics Corporation. All rights reserved. Colophon 1.1