MAXIM MAXQ618X

19-5778; Rev 1; 7/12
MAXQ618
16-Bit Microcontroller with Infrared Module
General Description
Features
The MAXQ618 is a low-power, 16-bit MAXQ® microcontroller designed for low-power applications including universal remote controls, consumer electronics, and white
goods. The device combines a powerful 16-bit RISC
microcontroller and integrated peripherals including two
universal synchronous/asynchronous receiver-transmitters (USARTs) and an SPI master/slave communications
port, along with an IR module with carrier frequency
generation and flexible port I/O capable of multiplexed
keypad control.
SHigh-Performance, Low-Power, 16-Bit RISC Core
The device includes 80KB of flash memory and 2KB of data
SRAM. The MAXQ61C is a ROM version of this device.
S16 x 16-Bit General-Purpose Working Registers
For the ultimate in low-power battery-operated performance, the device includes an ultra-low-power stop mode
(0.2µA typ). In this mode, the minimum amount of circuitry
is powered. Wake-up sources include external interrupts,
the power-fail interrupt, and a timer interrupt. The microcontroller runs from a wide 1.70V to 3.6V operating voltage.
Applications
Remote Controls
Battery-Powered Portable Equipment
Consumer Electronics
Home Appliances
White Goods
Block Diagram
SDC to 12MHz Operation Across Entire Operating Range
S1.70V to 3.6V Operating Voltage
S33 Total Instructions for Simplified Programming
SThree Independent Data Pointers Accelerate Data
Movement with Automatic Increment/Decrement
SDedicated Pointer for Direct Read from Code Space
S16-Bit Instruction Word, 16-Bit Data Bus
SMemory Features

80KB Flash Memory

2KB Data SRAM
SAdditional Peripherals

Power-Fail Warning

Power-On Reset (POR)/Brownout Reset

Automatic IR Carrier Frequency Generation
and Modulation

Two 16-Bit Programmable Timers/Counters
with Prescaler and Capture/Compare

One SPI Port and Two USART Ports

Programmable Watchdog Timer

8kHz Nanopower Ring Oscillator Wake-Up Timer

Up to 32 General-Purpose I/Os
SLow Power Consumption

0.2µA (typ), 2.0µA (max) in Stop Mode,
TA = +25NC, Power-Fail Monitor Disabled

2.0mA (typ) at 12MHz in Active Mode
MAXQ618
REGULATOR
16-BIT MAXQ
RISC CPU
IR DRIVER
VOLTAGE
MONITOR
CLOCK
80KB FLASH
MEMORY
IR TIMER
GPIO
WATCHDOG
1.5KB
UTILITY ROM
SPI
2x
16-BIT TIMER
8kHz NANO
RING
2KB
DATA SRAM
2 x USART
Ordering Information appears at end of data sheet.
For related parts and recommended products to use with this part,
refer to www.maxim-ic.com/MAXQ618.related.
MAXQ is a registered trademark of Maxim Integrated Products, Inc.
Note: Some revisions of this device may incorporate deviations from published specifications known as errata. Multiple revisions of any device may
be simultaneously available through various sales channels. For information about device errata, go to: www.maxim-ic.com/errata.
For pricing, delivery, and ordering information, please contact Maxim Direct
at 1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
1
MAXQ618
16-Bit Microcontroller with Infrared Module
TABLE OF CONTENTS
General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Recommended Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
SPI Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Pin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Pin Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Detailed Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Microprocessor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Stack Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Utility ROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Watchdog Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
IR Carrier Generation and Modulation Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Carrier Generation Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
IR Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
IR Transmit—Independent External Carrier and Modulator Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
IR Receive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Carrier Burst-Count Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
16-Bit Timers/Counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
USART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Serial Peripheral Interface (SPI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
General-Purpose I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
On-Chip Oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Power-Fail Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Applications Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Grounds and Bypassing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Additional Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Deviations from the MAXQ610 User’s Guide for the MAXQ618 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Development and Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Ordering Information/Selector Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Package Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
2
MAXQ618
16-Bit Microcontroller with Infrared Module
LIST OF FIGURES
Figure 1. IR Transmit Frequency Shifting Example (IRCFME = 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Figure 2. IR Transmit Carrier Generation and Carrier Modulator Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Figure 3. IR Transmission Waveform (IRCFME = 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Figure 4. External IRTXM (Modulator) Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Figure 5. IR Capture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Figure 6. Receive Burst-Count Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Figure 7. SPI Master Communication Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Figure 8. SPI Slave Communication Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Figure 9. On-Chip Oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Figure 10. Power-Fail Detection During Normal Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Figure 11. Stop Mode Power-Fail Detection States with Power-Fail Monitor Enabled . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Figure 12. Stop Mode Power-Fail Detection with Power-Fail Monitor Disabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
LIST OF TABLES
Table 1. Watchdog Interrupt Timeout (Sysclk = 12MHz, CD[1:0] = 00) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Table 2. USART Mode Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Table 3. Power-Fail Detection States During Normal Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Table 4. Stop Mode Power-Fail Detection States with Power-Fail Monitor Enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Table 5. Stop Mode Power-Fail Detection States with Power-Fail Monitor Disabled . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3
MAXQ618
16-Bit Microcontroller with Infrared Module
ABSOLUTE MAXIMUM RATINGS
(All voltages with respect to GND.)
Voltage Range on VDD..........................................-0.3V to +3.6V
Voltage Range on Any Lead Except VDD.-0.3V to (VDD + 0.5V)
Continuous Power Dissipation (TA = +70NC)
TQFN (single-layer board)
(derate 27mW/NC above +70NC)..........................2162.2mW
TQFN (multilayer board)
(derate 37mW/NC above +70NC).............................2963mW
Operating Temperature Range.............................. 0NC to +70NC
Storage Temperature Range............................. -65NC to +150NC
Lead Temperature (excluding dice; soldering, 10s).......+300NC
Soldering Temperature (reflow).......................................+260NC
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
RECOMMENDED OPERATING CONDITIONS
(VDD = VRST to 3.6V, TA = 0NC to +70NC, unless otherwise noted.) (Note 1)
PARAMETER
Supply Voltage
1.8V Internal Regulator
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
VDD
VRST
3.6
V
VREG18
1.62
1.8
1.98
V
Power-Fail Warning Voltage for
Supply
VPFW
Monitors VDD (Note 2)
1.75
1.8
1.85
V
Power-Fail Reset Voltage
VRST
Monitors VDD (Note 3)
1.64
1.67
1.70
V
POR Voltage
VPOR
Monitors VDD
1.0
1.42
V
RAM Data-Retention Voltage
VDRV
(Note 4)
1.0
Active Current
IDD_1
Sysclk = 12MHz (Note 5)
V
2.5
3.75
TA = +25NC
0.15
2.0
TA = 0°C +70NC
0.15
8
22
31
27.6
38
mA
IS1
Power-Fail Off
IS2
Power-Fail On
Current Consumption During
Power-Fail
IPFR
(Note 6)
[(3 x IS2) +
((PCI - 3) x (IS1 +
INANO))]/PCI
FA
Power Consumption During
POR
IPOR
(Note 7)
100
nA
Stop-Mode Current
Stop-Mode Resume Time
TA = +25NC
TA = 0°C to +70NC
tON
375 + (8192 x tHFXIN)
Fs
Power-Fail Monitor Startup Time
tPFM_ON
Power-Fail Warning Detection
Time
tPFW
Input Low Voltage for IRTX,
IRRX, RESET, and All Port Pins
VIL
VGND
0.3 x VDD
V
Input High Voltage for IRTX,
IRRX, RESET, and All Port Pins
VIH
0.7 x VDD
VDD
V
Input Hysteresis (Schmitt)
VIHYS
(Note 4)
FA
(Notes 4, 8)
150
10
Fs
300
VDD = 3.3V, TA = +25NC
Fs
mV
Input Low Voltage for HFXIN
VIL_HFXIN
VGND
0.3 x VDD
V
Input High Voltage for HFXIN
VIH_HFXIN
0.7 x VDD
VDD
V
IRRX Input Filter Pulse-Width
Reject
tIRRX_R
50
ns
4
MAXQ618
16-Bit Microcontroller with Infrared Module
RECOMMENDED OPERATING CONDITIONS (continued)
(VDD = VRST to 3.6V, TA = 0NC to +70NC, unless otherwise noted.) (Note 1)
PARAMETER
SYMBOL
IRRX Input Filter Pulse-Width
Accept
tIRRX_A
Output Low Voltage for IRTX
VOL_IRTX
CONDITIONS
MIN
TYP
300
VDD = 3.6V, IOL = 25mA (Note 4)
1.0
VDD = 2.35V, IOL = 10mA (Note 4)
1.0
0.4
0.5
VDD = 2.35V, IOL = 8mA (Note 4)
0.4
0.5
VDD = 1.85V, IOL = 4.5mA
0.4
0.5
VOL
Output High Voltage for IRTX
and All Port Pins
VOH
IOH = -2mA
Input/Output Pin Capacitance
for All Port Pins
CIO
(Note 4)
Input Pullup Resistor for
RESET, IRTX, IRRX, P0, P1, P2
IL
RPU
Internal pullup disabled
V
1.0
VDD = 3.6V, IOL = 11mA (Note 4)
Output Low Voltage for RESET
and All Port Pins (Note 9)
UNITS
ns
VDD = 1.85V, IOL = 4.5mA
Input Leakage Current
MAX
VDD - 0.5
-100
V
VDD
V
15
pF
+100
nA
VDD = 3.0V, VOL = 0.4V (Note 4)
16
28
39
VDD = 2.0V, VOL = 0.4V
17
30
41
kW
EXTERNAL CRYSTAL/RESONATOR
Crystal/Resonator
fHFXIN
Crystal/Resonator Period
tHFXIN
1/fHFXIN
ns
tXTAL_RDY
8192 x
tHFXIN
ms
Crystal/Resonator Warmup
Time
Oscillator Feedback Resistor
ROSCF
DC
From initial oscillation
(Note 4)
0.5
12
1.0
MHz
1.5
MW
12
MHz
EXTERNAL CLOCK INPUT
External Clock Frequency
fXCLK
External Clock Period
tXCLK
External Clock Duty Cycle
DC
1/fXCLK
tXCLK_DUTY (Note 4)
System Clock Frequency
fCK
System Clock Period
tCK
45
ns
55
fHFXIN
HFXOUT = GND
%
MHz
fXCLK
1/fCK
ns
NANOPOWER RING
TA = +25NC
3.0
8.0
TA = +25NC, VDD = POR voltage
(Note 4)
1.7
2.4
tNANO
(Note 4)
40
INANO
Typical at VDD = 1.64V,
TA = +25°C (Note 4)
Nanopower Ring Frequency
fNANO
Nanopower Ring Duty Cycle
Nanopower Ring Current
40
20.0
kHz
60
%
400
nA
FLASH MEMORY
System Clock During Flash
Programming/Erase
fFPSYSCLK
6
MHz
5
MAXQ618
16-Bit Microcontroller with Infrared Module
RECOMMENDED OPERATING CONDITIONS (continued)
(VDD = VRST to 3.6V, TA = 0NC to +70NC, unless otherwise noted.) (Note 1)
PARAMETER
SYMBOL
Flash Erase Time
Flash Programming Time per
Word
CONDITIONS
MIN
TYP
MAX
tME
Mass erase
20
40
tERASE
Page erase
20
40
tPROG
(Note 10)
20
100
Write/Erase Cycles
Data Retention
TA = +25NC
UNITS
ms
Fs
20,000
Cycles
100
Years
WAKE-UP TIMER
Wake-Up Timer Interval
tWAKEUP
1/fNANO
65,535/
fNANO
s
fCK/2
Hz
MAX
UNITS
IR
Carrier Frequency
fIR
(Note 4)
SPI ELECTRICAL CHARACTERISTICS
(VDD = VRST to 3.6V, TA = 0NC to +70NC, unless otherwise noted.) (Note 11)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
SPI Master Operating Frequency
1/tMCK
fCK/2
MHz
SPI Slave Operating Frequency
1/tSCK
fCK/4
MHz
SPI I/O Rise/Fall Time
tSPI_RF
23.6
ns
SCLK Output Pulse-Width High/
Low
tMCH,
tMCL
tMCK/2 tSPI_RF
ns
MOSI Output Hold Time After
SCLK Sample Edge
tMOH
tMCK/2 tSPI_RF
ns
MOSI Output Valid to Sample Edge
tMOV
tMCK/2 tSPI_RF
ns
MISO Input Valid to SCLK Sample
Edge Rise/Fall Setup
tMIS
25
ns
MISO Input to SCLK Sample Edge
Rise/Fall Hold
tMIH
0
ns
SCLK Inactive to MOSI Inactive
tMLH
tMCK/2 tSPI_RF
ns
SCLK Input Pulse-Width High/Low
CL = 15pF, pullup = 560W
8.3
tSCH, tSCL
tSCK/2
ns
SSEL Active to First Shift Edge
tSSE
tSPI_RF
ns
MOSI Input to SCLK Sample Edge
Rise/Fall Setup
tSIS
tSPI_RF
ns
MOSI Input from SCLK Sample
Edge Transition Hold
tSIH
tSPI_RF
ns
MISO Output Valid After SCLK Shift
Edge Transition
tSOV
2tSPI_RF
ns
6
MAXQ618
16-Bit Microcontroller with Infrared Module
SPI ELECTRICAL CHARACTERISTICS (continued)
(VDD = VRST to 3.6V, TA = 0NC to +70NC, unless otherwise noted.) (Note 11)
PARAMETER
SYMBOL
CONDITIONS
MIN
SSEL Inactive
tSSH
tCK +
tSPI_RF
SCLK Inactive to SSEL Rising
tSD
tSPI_RF
MISO Output Disabled After SSEL
Edge Rise
tSLH
TYP
MAX
UNITS
ns
ns
2tCK +
2tSPI_RF
ns
Note 1: Specifications to 0NC are guaranteed by design and are not production tested. Typical = +25NC, VDD = +3.3V, unless otherwise noted.
Note 2:VPFW can be programmed to the following nominal voltage trip points: 1.8V, 1.9V, 2.55V, and 2.75V ±3%. The values
listed in the Recommended Operating Conditions table are for the default configuration of 1.8V typical.
Note 3: The power-fail reset and POR detectors are designed to operate in tandem to ensure that one or both of these signals
is active at all times when VDD < VRST, ensuring the device maintains the reset state until minimum operating voltage is
achieved.
Note 4: Guaranteed by design and not production tested.
Note 5: Measured on the VDD pin and the device not in reset. All inputs are connected to GND or VDD. Outputs do not source/
sink any current. The device is executing code from flash memory.
Note 6: The power-check interval (PCI) can be set to always on, or to 1024, 2048, or 4096 nanopower ring clock cycles.
Note 7: Current consumption during POR when powering up while VDD is less than the POR release voltage.
Note 8: The minimum amount of time that VDD must be below VPFW before a power-fail event is detected; refer to the MAXQ610
User’s Guide for details.
Note 9: The maximum total current, IOH(MAX) and IOL(MAX), for all listed outputs combined should not exceed 32mA to satisfy the
maximum specified voltage drop. This does not include the IRTX output.
Note 10:Programming time does not include overhead associated with utility ROM interface.
Note 11:AC electrical specifications are guaranteed by design and are not production tested.
7
MAXQ618
16-Bit Microcontroller with Infrared Module
P1.0/INT0
P2.7/TDO
P2.6/TMS
P2.5/TDI
P2.4/TCK
GND
N.C.
N.C.
P3.7/INT15
P3.6/INT14
P3.5/INT13
32
31
30
29
28
27
26
25
24
23
TOP VIEW
33
Pin Configuration
P1.1/INT1
34
22
P3.4/INT12
P1.2/INT2
35
21
P3.3/INT11
P1.3/INT3
36
20
P3.2/INT10
P1.4/INT4
37
19
P3.1/INT9
P1.5/INT5
38
18
P3.0/INT8
P1.6/INT6
39
17
HFXOUT
P1.7/INT7
40
16
HFXIN
GND
41
15
GND
IRTX
42
14
REGOUT
IRRX
43
13
VDD
P0.0/IRTXM
44
12
RESET
MAXQ618
EP
5
6
7
8
9
10
11
P0.5/TBA0/TBA1
P0.6/TBB0
P0.7/TBB1
P2.0/MOSI
P2.1/MISO
P2.2/SCLK
P2.3/SSEL
3
P0.3/RX1
4
2
P0.2/TX0
P0.4/TX1
1
P0.1/RX0
+
TQFN
(7mm × 7mm)
NOTE: CONTACT FACTORY FOR BARE DIE PAD CONFIGURATION.
Pin Description
PIN
NAME
FUNCTION
BARE DIE
TQFN-EP
14
13
VDD
Supply Voltage
16
15
GND
Ground. Connect directly to the ground plane.
27, 43
28, 41
GND
Ground. For low-current applications (< 10mA of GPIO current, exclusive of IRTX sink
current), these pins can be left unconnected. If used, they should be connected directly
to the ground plane.
15
14
REGOUT
1.8V Regulator Output. This pin must be connected to ground through a 1.0FF external
ceramic-chip capacitor. The capacitor must be placed as close to this pin as possible.
No devices other than the capacitor should be connected to this pin.
POWER PINS
8
MAXQ618
16-Bit Microcontroller with Infrared Module
Pin Description (continued)
PIN
BARE DIE
TQFN-EP
NAME
FUNCTION
RESET PINS
13
12
RESET
Digital, Active-Low Reset Input/Output. The device remains in reset as long as this pin
is low and begins executing from the utility ROM at address 8000h when this pin returns
to a high state. The pin includes pullup current source; if this pin is driven by an external
device, it should be driven by an open-drain source capable of sinking in excess of
4mA. This pin can be left unconnected if there is no need to place the device in a reset
state using an external signal. This pin is driven low as an output when an internal reset
condition occurs.
CLOCK PINS
17
16
HFXIN
18
17
HFXOUT
High-Frequency Crystal Input. Connect an external crystal or resonator between
HFXIN and HFXOUT for use as the high-frequency system clock. Alternatively, HFXIN
is the input for an external, high-frequency clock source when HFXOUT is connected to
ground.
IR FUNCTION PINS
44
42
IRTX
IR Transmit Output. IR transmission pin capable of sinking 25mA. This pin defaults
to a high-impedance input with the weak pullup disabled during all forms of reset.
Software must configure this pin after release from reset to remove the high-impedance
input condition.
45
43
IRRX
IR Receive Input. This pin defaults to a high-impedance input with the weak pullup
disabled during all forms of reset. Software must configure this pin after release from
reset to remove the high-impedance input condition.
GENERAL-PURPOSE I/O AND SPECIAL FUNCTION PINS
Port 0 General-Purpose, Digital I/O Pins. These port pins function as general-purpose
I/O pins with their input and output states controlled by the PD0, PO0, and PI0 registers.
All port pins default to high-impedance mode after a reset. Software must configure
these pins after release from reset to remove the high-impedance condition. All special
functions must be enabled from software before they can be used.
GPIO PORT PIN
SPECIAL FUNCTION
IR Modulator Output
1
44
P0.0/IRTXM
P0.0
2
1
P0.1/RX0
P0.1
USART 0 Receive
3
2
P0.2/TX0
P0.2
USART 0 Transmit
4
3
P0.3/RX1
P0.3
USART 1 Receive
5
4
P0.4/TX1
P0.4
USART 1 Transmit
6
5
P0.5/TBA0/
TBA1
P0.5
Type B Timer 0 Pin A or
Type B Timer 1 Pin A
7
6
P0.6/TBB0
P0.6
Type B Timer 0 Pin B
8
7
P0.7/TBB1
P0.7
Type B Timer 1 Pin B
9
MAXQ618
16-Bit Microcontroller with Infrared Module
Pin Description (continued)
PIN
BARE DIE
TQFN-EP
NAME
FUNCTION
Port 1 General-Purpose, Digital I/O Pins with Interrupt Capability. These port pins
function as general-purpose I/O pins with their input and output states controlled by
the PD1, PO1, and PI1 registers. All port pins default to high-impedance mode after a
reset. Software must configure these pins after release from reset to remove the highimpedance condition. All external interrupts must be enabled from software before they
can be used.
33
35
36
38
39
40
41
42
33
34
35
36
37
38
39
40
P1.0/INT0
P1.1/INT1
P1.2/INT2
P1.3/INT3
P1.4/INT4
P1.5/INT5
P1.6/INT6
P1.7/INT7
GPIO PORT PIN
P1.0
P1.1
P1.2
P1.3
P1.4
P1.5
P1.6
P1.7
EXTERNAL INTERRUPT
INT0
INT1
INT2
INT3
INT4
INT5
INT6
INT7
Port 2 General-Purpose, Digital I/O Pins. These port pins function as general-purpose
I/O pins with their input and output states controlled by the PD2, PO2, and PI2 registers.
All port pins default to high-impedance mode after a reset. Software must configure
these pins after release from reset to remove the high-impedance condition. All special
functions must be enabled from software before they can be used.
9
10
11
12
28
29
30
31
8
9
10
11
29
30
31
32
P2.0/MOSI
P2.1/MISO
P2.2/SCLK
P2.3/SSEL
P2.4/TCK
P2.5/TDI
P2.6/TMS
P2.7/TDO
GPIO PORT PIN
P2.0
P2.1
P2.2
P2.3
P2.4
P2.5
P2.6
P2.7
SPECIAL FUNCTION
SPI: Master Out-Slave In
SPI: Master In-Slave Out
SPI: Slave Clock
SPI: Active-Low Slave Select
JTAG: Test Clock
JTAG: Test Data In
JTAG: Test Mode Select
JTAG: Test Data Out
Port 3 General-Purpose, Digital I/O Pins with Interrupt Capability. These port pins
function as general-purpose I/O pins with their input and output states controlled by
the PD3, PO3, and PI3 registers. All port pins default to high-impedance mode after a
reset. Software must configure these pins after release from reset to remove the highimpedance condition. All external interrupts must be enabled from software before they
can be used.
19
20
21
22
23
24
25
26
18
19
20
21
22
23
24
25
P3.0/INT8
P3.1/INT9
P3.2/INT10
P3.3/INT11
P3.4/INT12
P3.5/INT13
P3.6/INT14
P3.7/INT15
GPIO PORT PIN
P3.0
P3.1
P3.2
P3.3
P3.4
P3.5
P3.6
P3.7
EXTERNAL INTERRUPT
INT8
INT9
INT10
INT11
INT12
INT13
INT14
INT15
10
MAXQ618
16-Bit Microcontroller with Infrared Module
Pin Description (continued)
PIN
NAME
FUNCTION
BARE DIE
TQFN-EP
32, 34, 37
—
DNC
Do Not Connect. Do not bond out for normal operation.
—
26, 27
N.C.
No Connection. Not internally connected.
NO CONNECTION PINS
EXPOSED PAD
—
—
EP
Exposed Pad. For low-current applications (< 10mA of GPIO current, exclusive of IRTX
sink current), these pins can be left unconnected. If used, they should be connected
directly to the ground plane.
Detailed Description
The MAXQ618 provides integrated, low-cost solutions
that simplify the design of IR communications equipment
such as universal remote controls. Standard features
include the highly optimized, single-cycle, MAXQ, 16-bit
RISC core; 80KB flash memory; 2KB data RAM; soft
stack; 16 general-purpose registers; and three data
pointers. The MAXQ core has the industry’s best MIPS/
mA rating, allowing developers to achieve the same performance as competing microcontrollers at substantially
lower clock rates. Lower active-mode current combined
with the even lower MAXQ618 stop-mode current (0.2FA
typ) results in increased battery life. Application-specific
peripherals include flexible timers for generating IR carrier frequencies and modulation. A high-current IR drive
pin capable of sinking up to 25mA current and output
pins capable of sinking up to 5mA are ideal for IR applications. It also includes general-purpose I/O pins ideal
for keypad matrix input, and a power-fail-detection circuit
to notify the application when the supply voltage is nearing the microcontroller’s minimum operating voltage.
At the heart of the device is the MAXQ 16-bit, RISC core.
Operating from DC to 12MHz, almost all instructions execute in a single clock cycle (83.3ns at 12MHz), enabling
nearly 12MIPS true-code operation. When active device
operation is not required, an ultra-low-power stop mode
can be invoked from software, resulting in quiescent
current consumption of less than 0.2FA (typ) and 2.0FA
(max). The combination of high-performance instructions
and ultra-low stop-mode current increases battery life
over competing microcontrollers. An integrated POR circuit with brownout support resets the device to a known
condition following a power-up cycle or brownout condition. Additionally, a power-fail warning flag is set, and a
power-fail interrupt can be generated when the system
voltage falls below the power-fail warning voltage, VPFW.
The power-fail warning feature allows the application to
notify the user that the system supply is low and appropriate action should be taken.
Microprocessor
The device is based on Maxim’s low-power, 16-bit
MAXQ20S family of RISC cores. The core supports the
Harvard memory architecture with separate 16-bit program and data address buses. A fixed 16-bit instruction
word is standard, but data can be arranged in 8 or 16
bits. The MAXQ core in the device is implemented as
a pipelined processor with performance approaching
1MIPS per MHz. The 16-bit data path is implemented
around register modules, and each register module contributes specific functions to the core. The accumulator
module consists of sixteen 16-bit registers and is tightly
coupled with the arithmetic logic unit (ALU). A configurable soft stack supports program flow.
Execution of instructions is triggered by data transfer between functional register modules or between a
functional register module and memory. Because data
movement involves only source and destination modules,
circuit switching activities are limited to active modules
only. For power-conscious applications, this approach
localizes power dissipation and minimizes switching
noise. The modular architecture also provides a maximum of flexibility and reusability that are important for a
microprocessor used in embedded applications.
The MAXQ instruction set is highly orthogonal. All arithmetical and logical operations can use any register in
conjunction with the accumulator. Data movement is supported from any register to any other register. Memory
is accessed through specific data-pointer registers with
autoincrement/decrement support.
11
MAXQ618
16-Bit Microcontroller with Infrared Module
Memory
The microcontroller incorporates several memory types:
only, and are generally of no use to the end-application developer
• User-callable routines for buffer copying and fast
table lookup (more information on these routines can
be found in the MAXQ610 User’s Guide)
• 80KB flash memory
• 2KB SRAM data memory
• 1.5KB utility ROM
• Soft stack
Stack Memory
The device provides a soft stack that can be used to store
program return addresses (for subroutine calls and interrupt handling) and other general-purpose data. This soft
stack is located in the 2KB SRAM data memory, which
means that the SRAM data memory must be shared
between the soft stack and general-purpose application
data storage. However, the location and size of the soft
stack is determined by the user, providing maximum
flexibility when allocating resources for a particular application. The stack is used automatically by the processor
when the CALL, RET, and RETI instructions are executed
and when an interrupt is serviced. An application can
also store and retrieve values explicitly using the stack by
means of the PUSH, POP, and POPI instructions.
The SP pointer indicates the current top of the stack,
which initializes by default to the top of the SRAM data
memory. As values are pushed onto the stack, the SP
pointer decrements, which means that the stack grows
downward towards the bottom (lowest address) of the
data memory. Popping values off the stack causes the
SP pointer value to increase. Refer to the MAXQ610
User’s Guide for more details.
Utility ROM
The utility ROM is a 1.5KB block of internal ROM memory
located in program space beginning at address 8000h.
This ROM includes the following routines:
• Production test routines (internal memory tests, memory loader, etc.), which are used for internal testing
Following any reset, execution begins in the utility ROM
at address 8000h. At this point, unless test mode has
been invoked (which requires special programming
through the JTAG interface), the utility ROM in the device
always automatically jumps to location 0000h, which is
the beginning of user application code.
Watchdog Timer
The internal watchdog timer greatly increases system
reliability. The timer resets the device if software execution is disturbed. The watchdog timer is a free-running
counter designed to be periodically reset by the application software. If software is operating correctly, the
counter is periodically reset and never reaches its maximum count. However, if software operation is interrupted,
the timer does not reset, triggering a system reset and
optionally a watchdog timer interrupt. This protects the
system against electrical noise or electrostatic discharge
(ESD) upsets that could cause uncontrolled processor
operation. The internal watchdog timer is an upgrade to
older designs with external watchdog devices, reducing
system cost and simultaneously increasing reliability.
The watchdog timer functions as the source of both the
watchdog timer timeout and the watchdog timer reset.
The timeout period can be programmed in a range of
215 to 224 system clock cycles. An interrupt is generated when the timeout period expires if the interrupt
is enabled. All watchdog timer resets follow the programmed interrupt timeouts by 512 system clock cycles.
If the watchdog timer is not restarted for another full
interval in this time period, a system reset occurs when
the reset timeout expires. See Table 1.
Table 1. Watchdog Interrupt Timeout (Sysclk = 12MHz, CD[1:0] = 00)
WATCHDOG INTERRUPT TIMEOUT
WATCHDOG RESET AFTER
WATCHDOG INTERRUPT (μs)
Sysclk/215
2.7ms
42.7
01
Sysclk/218
21.9ms
42.7
10
Sysclk/221
174.7ms
42.7
11
Sysclk/224
1.4s
42.7
WD[1:0]
WATCHDOG CLOCK
00
12
MAXQ618
16-Bit Microcontroller with Infrared Module
IR Carrier Generation and
Modulation Timer
The dedicated IR timer/counter module simplifies lowspeed infrared (IR) communication. The IR timer implements two pins (IRTX and IRRX) for supporting IR transmit and receive, respectively. The IRTX pin has no corresponding port pin designation, so the standard PD, PO,
and PI port control status bits are not present. However,
the IRTX pin output can be manipulated high or low using
the PWCN.IRTXOUT and PWCN.IRTXOE bits when the IR
timer is not enabled (i.e., IREN = 0).
The IR timer is composed of a carrier generator and a
carrier modulator. The carrier generation module uses
the 16-bit IR carrier register (IRCA) to define the high
and low time of the carrier through the IR carrier high
byte (IRCAH) and IR carrier low byte (IRCAL). The carrier
modulator uses the IR data bit (IRDATA) and IR modulator time register (IRMT) to determine whether the carrier
or the idle condition is present on IRTX.
The IR timer is enabled when the IR enable bit (IREN) is
set to 1. The IR Value register (IRV) defines the beginning value for the carrier modulator. During transmission,
the IRV register is initially loaded with the IRMT value
and begins down counting towards 0000h, whereas in
receive mode it counts upward from the initial IRV register value. During the receive operation, the IRV register
can be configured to reload with 0000h when capture
occurs on detection of selected edges or can be allowed
to continue free-running throughout the receive operation. An overflow occurs when the IR timer value rolls over
from 0FFFFh to 0000h. The IR overflow flag (IROV) is set
to 1 and an interrupt is generated if enabled (IRIE = 1).
Carrier Generation Module
The IRCAH byte defines the carrier high time in terms of
the number of IR input clocks, whereas the IRCAL byte
defines the carrier low time.
• IR Input Clock (fIRCLK) = fSYS/2IRDIV[2:0]
• Carrier Frequency (fCARRIER) = fIRCLK/(IRCAH + IRCAL + 2)
frequency shifting is possible from one interval to the
next, which is illustrated in Figure 1.
Figure 2 illustrates the basic carrier generation and its
path to the IRTX output pin. The IR transmit polarity bit
(IRTXPOL) defines the starting/idle state and the carrier
polarity of the IRTX pin when the IR timer is enabled.
IR Transmission
During IR transmission (IRMODE = 1), the carrier generator creates the appropriate carrier waveform, while the
carrier modulator performs the modulation. The carrier
modulation can be performed as a function of carrier
cycles or IRCLK cycles dependent on the setting of the
IRCFME bit. When IRCFME = 0, the IRV down counter is
clocked by the carrier frequency and thus the modulation is a function of carrier cycles. When IRCFME = 1, the
IRV down counter is clocked by IRCLK, allowing carrier
modulation timing with IRCLK resolution.
The IRTXPOL bit defines the starting/idle state as well as
the carrier polarity for the IRTX pin. If IRTXPOL = 1, the
IRTX pin is set to a logic-high when the IR timer module is
enabled. If IRTXPOL = 0, the IRTX pin is set to a logic-low
when the IR timer is enabled.
A separate register bit, IR data (IRDATA), is used to determine
whether the carrier generator output is output to the IRTX pin
for the next IRMT carrier cycles. When IRDATA = 1, the carrier waveform (or inversion of this waveform if IRTXPOL = 1)
is output on the IRTX pin during the next IRMT cycles. When
IRDATA = 0, the idle condition, as defined by IRTXPOL, is
output on the IRTX pin during the next IRMT cycles.
The IR timer acts as a down counter in transmit mode.
An IR transmission starts when the IREN bit is set to 1
when IRMODE = 1; when the IRMODE bit is set to 1 when
IREN = 1; or when IREN and IRMODE are both set to 1 in
the same instruction. The IRMT and IRCA registers, along
with the IRDATA and IRTXPOL bits, are sampled at the
beginning of the transmit process and every time the IR
timer value reload its value. When the IRV reaches 0000h
value, on the next carrier clock, it does the following:
1) Reloads IRV with IRMT.
• Carrier High Time = IRCAH + 1
2) Samples IRCA, IRDATA, and IRTXPOL.
• Carrier Low Time = IRCAL + 1
3) Generates IRTX accordingly.
• Carrier Duty Cycle = (IRCAH + 1)/(IRCAH + IRCAL + 2)
4) Sets IRIF to 1.
During transmission, the IRCA register is latched for each
IRV down-count interval, and is sampled along with the
IRTXPOL and IRDATA bits at the beginning of each new
IRV down-count interval so that duty-cycle variation and
5) Generates an interrupt to the CPU if enabled (IRIE = 1).
To terminate the current transmission, the user can
switch to receive mode (IRMODE = 0) or clear IREN to 0.
Carrier Modulation Time = IRMT + 1 carrier cycles
13
MAXQ618
16-Bit Microcontroller with Infrared Module
IRCA
IRCA = 0202h
IRCA = 0002h
IRMT
IRMT = 3
IRMT = 5
IRCA, IRMT, IRDATA SAMPLED AT END OF IRV
DOWN-COUNT INTERVAL
3
2
1
0
5
4
3
2
1
0
CARRIER OUTPUT
(IRV)
IRDATA
0
1
0
IR INTERRUPT
IRTX
IRTXPOL = 1
IRTX
IRTXPOL = 0
Figure 1. IR Transmit Frequency Shifting Example (IRCFME = 0)
IRTXPOL
0
CARRIER GENERATION
IRCLK
IRTX PIN
1
CARRIER
IRCAH + 1
IRCAL + 1
IRCFME
0
1
IRDATA
IRMT
SAMPLE
IRDATA ON
IRV = 0000h
IR INTERRUPT
CARRIER MODULATION
Figure 2. IR Transmit Carrier Generation and Carrier Modulator Control
14
MAXQ618
16-Bit Microcontroller with Infrared Module
IR Transmit—Independent External Carrier
and Modulator Outputs
IRTXPOL = 0) on each IRV down-count interval boundary
just as if it were being used to internally modulate the carrier frequency. If IRTXPOL = 1, the inverse of the IRDATA
bit is output to the IRTXM pin on the IRV interval downcount boundaries. See Figure 4. When the envelope
mode is enabled, it is possible to output either the modulated (IRENV[1:0] = 01b) or unmodulated (IRENV[1:0] =
10b) carrier to the IRTX pin.
The normal transmit mode modulates the carrier based
upon the IRDATA bit. However, the user has the option
to input the modulator (envelope) on an external pin if
desired. If the IRENV[1:0] bits are configured to 01b or
10b, the modulator/envelope is output to the IRTXM pin.
The IRDATA bit is output directly to the IRTXM pin (if
IRMT = 3
CARRIER OUTPUT
(IRV)
3
2
1
0
3
2
1
0
IRDATA
0
1
0
IR INTERRUPT
IRTX
IRTXPOL = 1
IRTX
IRTXPOL = 0
Figure 3. IR Transmission Waveform (IRCFME = 0)
IRTXM
IRTXPOL = 1
IRTXM
IRTXPOL = 0
IRDATA
1
0
1
0
1
0
1
0
IR INTERRUPT
IRV INTERVAL
IRMT
IRMT
IRMT
IRMT
Figure 4. External IRTXM (Modulator) Output
15
MAXQ618
16-Bit Microcontroller with Infrared Module
CARRIER GENERATION
CARRIER MODULATION
IRCLK
IRCAH + 1
0
IRCAL + 1
IR TIMER OVERFLOW
1
IRCFME
INTERRUPT TO CPU
0000h
IRV
IR INTERRUPT
COPY IRV TO IRMT
ON EDGE DETECT
IRXRL
IRRX PIN
RESET IRV TO 0000h
EDGE DETECT
IRDATA
Figure 5. IR Capture
IR Receive
When configured in receive mode (IRMODE = 0), the
IR hardware supports the IRRX capture function. The
IRRXSEL[1:0] bits define which edge(s) of the IRRX pin
should trigger the IR timer capture function.
The IR module starts operating in the receive mode when
IRMODE = 0 and IREN = 1. Once started, the IR timer
(IRV) starts up counting from 0000h when a qualified
capture event as defined by IRRXSEL happens. The IRV
register is, by default, counting carrier cycles as defined
by the IRCA register. However, the IR carrier frequency
detect (IRCFME) bit can be set to 1 to allow clocking of
the IRV register directly with the IRCLK for finer resolution. When IRCFME = 0, the IRCA defined carrier is
counted by IRV. When IRCFME = 1, the IRCLK clocks
the IRV register.
On the next qualified event, the IR module does the
following:
1) Captures the IRRX pin state and transfers its value to
IRDATA. If a falling edge occurs, IRDATA = 0. If a rising edge occurs, IRDATA = 1.
2) Transfers its current IRV value to the IRMT.
3) Resets IRV content to 0000h (if IRXRL = 1).
4) Continues counting again until the next qualified event.
If the IR timer value rolls over from 0FFFFh to 0000h
before a qualified event happens, the IR timer overflow
(IROV) flag is set to 1 and an interrupt is generated, if
enabled. The IR module continues to operate in receive
mode until it is stopped by switching into transmit mode
(IRMODE = 1) or clearing IREN = 0.
Carrier Burst-Count Mode
A special mode reduces the CPU processing burden
when performing IR learning functions. Typically, when
operating in an IR learning capacity, some number of
carrier cycles are examined for frequency determination. Once the frequency has been determined, the IR
receive function can be reduced to counting the number
of carrier pulses in the burst and the duration of the
combined mark-space time within the burst. To simplify
this process, the receive burst-count mode (as enabled
by the RXBCNT bit) can be used. When RXBCNT = 0,
the standard IR receive capture functionality is in place.
When RXBCNT = 1, the IRV capture operation is disabled and the interrupt flag associated with the capture
no longer denotes a capture. In the carrier burst-count
mode, the IRMT register only counts qualified edges.
The IRIF interrupt flag (normally used to signal a capture
when RXBCNT = 0) now becomes set if two IRCA cycles
elapse without getting a qualified edge. The IRIF interrupt
flag thus denotes absence of the carrier and the beginning of a space in the receive signal. When the RXBCNT
bit is changed from 0 to 1, the IRMT register is set to
0001h. The IRCFME bit is still used to define whether the
IRV register is counting system IRCLK clocks or IRCAdefined carrier cycles. The IRXRL bit defines whether
the IRV register is reloaded with 0000h on detection of
16
MAXQ618
16-Bit Microcontroller with Infrared Module
CARRIER FREQUENCY
CALCULATION
IRMT = PULSE COUNTING
IRV = CARRIER CYCLE COUNTING
IRMT = PULSE COUNTING
IRRX
IRV
IRMT
1
2
3
4
6
7
8
5
1 TO 4
9
CAPTURE INTERRUPT (IRIF = 1).
IRV ≥ IRMT.
IRV = 0 (IF IRXRL = 1).
5
SOFTWARE SETS IRCA = CARRIER FREQUENCY.
SOFTWARE SETS RXBCNT = 1 (WHICH CLEARS IRMT = 0001 IN HARDWARE).
SOFTWARE CLEARS IRCFME = 0 SO THAT IRV COUNTS CARRIER CYCLES. IRV IS RESET TO 0 ON QUALIFIED EDGE DETECTION IF IRXRL = 1.
SOFTWARE ADDS TO IRMT THE NUMBER OF PULSES USED FOR CARRIER MEASUREMENT.
IRCA x 2x COUNTER FOR SPACE CAN BEGIN IMMEDIATELY (QUALIFIED EDGE RESETS).
6
QUALIFIED EDGE DETECTED: IRMT++
IRV RESET TO 0 IF IRXRL = 1.
7
IRCA x 2 PERIOD ELAPSES: IRIF = 1; CARRIER ABSENCE = SPACE.
BURST MARK = IRMT PULSES.
SOFTWARE CLEARS RXBCNT = 0 SO THAT WE CAPTURE ON THE NEXT QUALIFIED EDGE.
8
9
QUALIFIED EDGE DETECTED: IRIF = 1, CAPTURE IRV IRMT AS THE BURST SPACE (PLUS UP TO ONE CARRIER CYCLE).
SOFTWARE SET RXBCNT = 1 AS IN (5).
CONTINUE (5) TO (8) UNTIL LEARNING SPACE EXCEEDS SOME DURATION. IRV ROLLOVERS CAN BE USED.
Figure 6. Receive Burst-Count Example
a qualified edge (per the IRXSEL[1:0] bits). Figure 6
and the descriptive sequence embedded in the figure
illustrate the expected usage of the receive burst-count
mode.
16-Bit Timers/Counters
The microcontroller provides two timers/counters that
support the following functions:
• 16-bit up/down autoreload
• Counter function of external pulse
• 16-bit timer with capture
• 16-bit timer with compare
• Input/output enhancements for pulse-width modulation
• Set/reset/toggle output state on comparator match
• Prescaler with 2n divider (for n = 0, 2, 4, 6, 8, 10)
• 16-bit timer/counter
17
MAXQ618
16-Bit Microcontroller with Infrared Module
USART
Serial Peripheral Interface (SPI)
The device provides two USART peripherals with the following features:
The integrated SPI provides an independent serial
communication channel that communicates synchronously with peripheral devices in a multiple master or
multiple slave system. The interface allows access to
a 4-wire, full-duplex serial bus, and can be operated in
either master mode or slave mode. Collision detection
is provided when two or more masters attempt a data
transfer at the same time.
• 2-wire interface
• Full-duplex operation for asynchronous data transfers
• Half-duplex operation for synchronous data transfers
• Programmable interrupt when transmit or receive data
operation completes
The maximum SPI master transfer rate is Sysclk/2. When
operating as an SPI slave, the device can support up to
Sysclk/4 SPI transfer rate. Data is transferred as an 8-bit
or 16-bit value, MSB first. In addition, the SPI module
supports configuration of an active SSEL state (active low
or active high) through the slave active select.
• Independent programmable baud-rate generator
• Optional 9th bit parity support
• Start/stop bit support
Table 2. USART Mode Details
MODE
TYPE
START BITS
DATA BITS
STOP BITS
Mode 0
Synchronous
N/A
8
N/A
Mode 1
Asynchronous
1
8
1
Mode 2
Asynchronous
1
8+1
1
Mode 3
Asynchronous
1
8+1
1
SHIFT
SAMPLE
SHIFT
SAMPLE
SSEL
SCLK
CKPOL/CKPHA
0/1 OR 1/0
tMCK
tMCH
tMCL
SCLK
CKPOL/CKPHA
0/0 OR 1/1
tMOH
tMOV
MSB
MOSI
MSB
tMLH
LSB
MSB-1
tMIS
MISO
tRF
tMIH
MSB-1
LSB
Figure 7. SPI Master Communication Timing
18
MAXQ618
16-Bit Microcontroller with Infrared Module
SHIFT
SSEL
SAMPLE
SHIFT
SAMPLE
tSSH
tSSE
tSD
tSCK
SCLK
CKPOL/CKPHA
0/1 OR 1/0
tSCH
SCLK
CKPOL/CKPHA
0/0 OR 1/1
tSCL
tSIS
tSIH
MSB
MOSI
MSB-1
LSB
tSOV
MSB
MISO
tRF
tSLH
MSB-1
LSB
Figure 8. SPI Slave Communication Timing
General-Purpose I/O
VDD
The microcontroller provides port pins for general-purpose I/O that have the following features:
HFXIN
CLOCK CIRCUIT
STOP
• CMOS output drivers
• Schmitt trigger inputs
RF
• Optional weak pullup to VDD when operating in input
mode
While the microcontroller is in a reset state, all port pins
become high impedance with both weak pullups and
input buffers disabled, unless otherwise noted.
From a software perspective, each port appears as a
group of peripheral registers with unique addresses.
Special function pins can also be used as general-purpose I/O pins when the special functions are disabled.
For a detailed description of the special functions available for each pin, refer to the MAXQ610 User’s Guide.
On-Chip Oscillator
An external quartz crystal or a ceramic resonator can be
connected between HFXIN and HFXOUT, as illustrated
in Figure 9.
HFXOUT
C1
C2
RF = 1MI Q50%
C1 = C2 = 12pF
Figure 9. On-Chip Oscillator
Noise at HFXIN and HFXOUT can adversely affect onchip clock timing. It is good design practice to place the
crystal and capacitors near the oscillator circuitry and
connect HFXIN and HFXOUT to ground with a direct
short trace. The typical values of external capacitors vary
with the type of crystal to be used and should be initially
selected based on load capacitance as suggested by
the manufacturer.
19
MAXQ618
16-Bit Microcontroller with Infrared Module
Operating Modes
The lowest power mode of operation is stop mode. In this
mode, CPU state and memories are preserved, but the
CPU is not actively running. Wake-up sources include
external I/O interrupts, the power-fail warning interrupt,
wake-up timer, or a power-fail reset. Any time the microcontroller is in a state where code does not need to be
executed, the user software can put the device into stop
mode. The nanopower ring oscillator is an internal ultralow-power (400nA) 8kHz ring oscillator that can be used
to drive a wake-up timer that exits stop mode. The wakeup timer is programmable by software in steps of 125Fs
up to approximately 8s.
The power-fail monitor is always on during normal operation. However, it can be selectively disabled during stop
mode to minimize power consumption. This feature is
enabled using the power-fail monitor disable (PFD) bit
in the PWCN register. The reset default state for the PFD
bit is 1, which disables the power-fail monitor function
during stop mode. If power-fail monitoring is disabled
(PFD = 1) during stop mode, the circuitry responsible
for generating a power-fail warning or reset is shut down
and neither condition is detected. Thus, the VDD < VRST
condition does not invoke a reset state.
VDD
t < tPFW
t ≥ tPFW
Power-Fail Detection
Figures 10, 11, and 12 show the power-fail detection and
response during normal and stop-mode operation. If a
reset is caused by a power-fail, the power-fail monitor
can be set to one of the following intervals:
• Always on—continuous monitoring
• 211 nanopower ring oscillator clocks (~256ms)
• 212 nanopower ring oscillator clocks (~512ms)
• 213 nanopower ring oscillator clocks (~1.024s)
In the case where the power-fail circuitry is periodically
turned on, the power-fail detection is turned on for two
nanopower ring-oscillator cycles. If VDD > VRST during
detection, VDD is monitored for an additional nanopower
ring-oscillator period. If VDD remains above VRST for the
third nanopower ring period, the CPU exits the reset state
and resumes normal operation from utility ROM at 8000h
after satisfying the crystal warmup period.
If a reset is generated by any other event, such as the
RESET pin being driven low externally or the watchdog timer, the power-fail, internal regulator, and crystal
remain on during the CPU reset. In these cases, the CPU
exits the reset state in less than 20 crystal cycles after the
reset source is removed.
t ≥ tPFW
t ≥ tPFW
C
VPFW
G
VRST
E
F
B
H
D
VPOR
I
A
INTERNAL RESET
(ACTIVE HIGH)
Figure 10. Power-Fail Detection During Normal Operation
20
MAXQ618
16-Bit Microcontroller with Infrared Module
Table 3. Power-Fail Detection States During Normal Operation
STATE
POWER-FAIL
INTERNAL
REGULATOR
CRYSTAL
OSCILLATOR
SRAM
RETENTION
A
On
Off
Off
—
VDD < VPOR.
B
On
On
On
—
VPOR < VDD < VRST.
Crystal warmup time, tXTAL_RDY.
CPU held in reset.
C
On
On
On
—
VDD > VRST.
CPU normal operation.
D
On
On
On
—
Power drop too short.
Power-fail not detected.
—
VRST < VDD < VPFW.
PFI is set when VRST < VDD < VPFW and
maintains this state for at least tPFW, at which
time a power-fail interrupt is generated (if
enabled).
CPU continues normal operation.
E
On
On
On
F
On
(Periodically)
Off
Off
Yes
G
On
On
On
—
H
On
(Periodically)
Off
Off
Yes
I
Off
Off
Off
—
COMMENTS
VPOR < VDD < VRST.
Power-fail detected.
CPU goes into reset.
Power-fail monitor turns on periodically.
VDD > VRST.
Crystal warmup time, tXTAL_RDY.
CPU resumes normal operation from 8000h.
VPOR < VDD < VRST.
Power-fail detected.
CPU goes into reset.
Power-fail monitor turns on periodically.
VDD < VPOR.
Device held in reset. No operation allowed.
21
MAXQ618
16-Bit Microcontroller with Infrared Module
VDD
t < tPFW
A
t ≥ tPFW
t ≥ tPFW
VPFW
D
VRST
B
C
E
VPOR
F
STOP
INTERNAL RESET
(ACTIVE HIGH)
Figure 11. Stop Mode Power-Fail Detection States with Power-Fail Monitor Enabled
Table 4. Stop Mode Power-Fail Detection States with Power-Fail Monitor Enabled
STATE
POWER-FAIL
INTERNAL
REGULATOR
CRYSTAL
OSCILLATOR
SRAM
RETENTION
A
On
Off
Off
Yes
Application enters stop mode.
VDD > VRST.
CPU in stop mode.
B
On
Off
Off
Yes
Power drop too short.
Power-fail not detected.
COMMENTS
C
On
On
On
Yes
VRST < VDD < VPFW.
Power-fail warning detected.
Turn on regulator and crystal.
Crystal warmup time, tXTAL_RDY.
Exit stop mode.
D
On
Off
Off
Yes
Application enters stop mode.
VDD > VRST.
CPU in stop mode.
E
On
(Periodically)
Off
Off
Yes
VPOR < VDD < VRST.
Power-fail detected.
CPU goes into reset.
Power-fail monitor turns on periodically.
F
Off
Off
Off
—
VDD < VPOR.
Device held in reset. No operation allowed.
22
MAXQ618
16-Bit Microcontroller with Infrared Module
VDD
A
D
VPFW
B
VRST
C
E
VPOR
F
STOP
INTERNAL RESET
(ACTIVE HIGH)
INTERRUPT
Figure 12. Stop Mode Power-Fail Detection with Power-Fail Monitor Disabled
Table 5. Stop Mode Power-Fail Detection States with Power-Fail Monitor Disabled
STATE
POWER-FAIL
INTERNAL
REGULATOR
CRYSTAL
OSCILLATOR
SRAM
RETENTION
A
Off
Off
Off
Yes
Application enters stop mode.
VDD > VRST.
CPU in stop mode.
B
Off
Off
Off
Yes
VDD < VPFW.
Power-fail not detected because power-fail
monitor is disabled.
Yes
VRST < VDD < VPFW.
An interrupt occurs that causes the CPU to
exit stop mode.
Power-fail monitor is turned on, detects a
power-fail warning, and sets the power-fail
interrupt flag.
Turn on regulator and crystal.
Crystal warmup time, tXTAL_RDY.
On stop mode exit, CPU vectors to the
higher priority of power-fail and the interrupt
that causes stop mode exit.
C
On
On
On
COMMENTS
23
MAXQ618
16-Bit Microcontroller with Infrared Module
Table 5. Stop Mode Power-Fail Detection States with Power-Fail Monitor Disabled
(continued)
STATE
POWER-FAIL
INTERNAL
REGULATOR
CRYSTAL
OSCILLATOR
SRAM
RETENTION
D
Off
Off
Off
Yes
Application enters stop mode.
VDD > VRST.
CPU in stop mode.
COMMENTS
E
On
(Periodically)
Off
Off
Yes
VPOR < VDD < VRST.
An interrupt occurs that causes the CPU to
exit stop mode.
Power-fail monitor is turned on, detects a
power-fail, and puts CPU in reset.
Power-fail monitor is turned on periodically.
F
Off
Off
Off
—
VDD < VPOR.
Device held in reset. No operation allowed.
Applications Information
The low-power, high-performance RISC architecture of
this device makes it an excellent fit for many portable or
battery-powered applications. It is ideally suited for applications such as universal remote controls that require the
cost-effective integration of IR transmit/receive capability.
purpose I/O pins. Negative voltage spikes on power pins
are especially problematic as they directly couple to the
internal power buses. Devices such as keypads can conduct electrostatic discharges directly into the microcontroller and seriously damage the device. System designers must protect components against these transients
that can corrupt system memory.
Grounds and Bypassing
Additional Documentation
Careful PCB layout significantly minimizes system-level
digital noise that could interact with the microcontroller
or peripheral components. The use of multilayer boards
is essential to allow the use of dedicated power planes.
The area under any digital components should be a continuous ground plane if possible. Keep bypass capacitor
leads short for best noise rejection and place the capacitors as close to the leads of the devices as possible.
CMOS design guidelines for any semiconductor require
that no pin be taken above VDD or below GND. Violation
of this guideline can result in a hard failure (damage to
the silicon inside the device) or a soft failure (unintentional modification of memory contents). Voltage spikes
above or below the device’s absolute maximum ratings
can potentially cause a devastating IC latchup.
Microcontrollers commonly experience negative voltage spikes through either their power pins or general-
Designers must have the following documents to fully
use all the features of this device. This data sheet
contains pin descriptions, feature overviews, and electrical specifications. Errata sheets contain deviations
from published specifications. The user’s guides offer
detailed information about device features and operation. The following documents can be downloaded from
www.maxim-ic.com/microcontrollers.
• This MAXQ618 data sheet, which contains electrical/
timing specifications, pin descriptions, and package
information.
• The MAXQ618 revision-specific
(www.maxim-ic.com/errata).
errata
sheet
• The MAXQ610 User’s Guide, which contains detailed information on features and operation, including programming.
24
MAXQ618
16-Bit Microcontroller with Infrared Module
Deviations from the MAXQ610 User’s Guide
for the MAXQ618
The MAXQ610 User’s Guide contains all the information that is needed to develop application code for the
MAXQ618 microcontroller. However, even though the
MAXQ610 and the MAXQ618 are largely code-compatible, there are certain differences between the two
devices that must be kept in mind when referring to the
MAXQ610 User’s Guide.
Development and
Technical Support
Maxim and third-party suppliers provide a variety of
highly versatile, affordably priced development tools for
this microcontroller, including the following:
• Compilers
• In-circuit emulators
The following registers on the MAXQ610 (which are
described in the MAXQ610 User’s Guide) do not exist
on the MAXQ618, and all references to them should be
disregarded:
• Integrated Development Environments (IDEs)
• Port 4 Output Register (PO4)
A partial list of development tool vendors can be found at
www.maxim-ic.com/MAXQ_tools.
• Port 4 Direction Register (PD4)
• Serial-to-JTAG and USB-to-JTAG interface boards for
programming and debugging (for microcontrollers
with rewritable memory)
For technical support, go to https://support.maxim-ic.
com/micro.
• Port 4 Input Register (PI4)
Ordering Information/Selector Guide
TEMP RANGE
OPERATING
VOLTAGE (V)
PROGRAM
MEMORY (KB)
DATA
MEMORY (KB)
GPIO
MAXQ618J-0000+
0NC to +70NC
1.7 to 3.6
80 Flash
2
32
44 TQFN-EP*
MAXQ618X-0000+
0NC to +70NC
1.7 to 3.6
80 Flash
2
32
Bare die
PART
PIN-PACKAGE
Note: The 4-digit suffix “-0000” indicates a microcontroller in the default state with the flash memory unprogrammed. Any value
other than 0000 indicates a device preprogrammed at Maxim with proprietary customer-supplied software. For more information on
factory preprogramming of these devices, contact Maxim at https://support.maxim-ic.com/micro. Information on masked ROM
devices is also available.
+Denotes a lead(Pb)-free/RoHS-compliant package.
*EP = Exposed pad.
Package Information
For the latest package outline information and land patterns (footprints), go to www.maxim-ic.com/packages. Note that a “+”, “#”, or
“-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains
to the package regardless of RoHS status.
PACKAGE TYPE
PACKAGE CODE
OUTLINE NO.
LAND PATTERN NO.
44 TQFN-EP
T4477+2
21-0144
90-0127
25
MAXQ618
16-Bit Microcontroller with Infrared Module
Revision History
REVISION
NUMBER
REVISION
DATE
0
3/11
Initial release
7/12
Added the continuous power dissipation information to the Absolute Maximum
Ratings section; removed the ESR reference from the REGOUT description in the
Pin Description table; changed the MAXQ core reference to MAXQ20S core in the
Microprocessor section; updated the IRDIV bit range from [1:0] to [2:0] in the Carrier
Generation Module section
1
DESCRIPTION
PAGES
CHANGED
—
4, 8, 11, 13
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied.
Maxim reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in the Electrical
Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.
Maxim Integrated Products, Inc. 160 Rio Robles, San Jose, CA 95134 USA 1-408-601-1000
© 2012
Maxim Integrated Products 26
Maxim is a registered trademark of Maxim Integrated Products, Inc.