规格书编号 SPEC NO: 产品 规 格书 SPECIFICATION CUSTOMER 客 户: PRODUCT 产 品: SAW FILTER MODEL NO 型 号: HDF4621 PREPARED 编 制: CHECKED 审 核: APPROVED 批 准: D A T E 日 期: 2006-7-10 客户确认 CUSTOMER RECEIVED: 审核 CHECKED 批准 APPROVED 日期 DATE 无锡市好达电子有限公司 Shoulder Electronics Limited www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 1 of 11 SAW FILTER HDF4621 更改历史记录 History Record 更改日期 Date www.shoulder.cn 规格书编号 Spec. No. 产品型号 Part No. 客户产品型号 Customer No. Tel:0755-82916880 Fax:0755-82916881 更改内容描述 Modify Content E-mail:[email protected] 备注 Remark Page 2 of 11 SAW FILTER HDF4621 1. Features _ RF bandpass filter _ High attenuation _ Usable bandwidth 5MHz _ No matching 50Ω single-ended operation _ Ceramic Surface Mounted Device (SMD) Package 2. ELECTRICAL SPECIFICATION Parameter Operating Temperature Range Storage Temperature Range DC Voltage VDC Power Handling Capability Electronic Characteristics 2-1.Typical frequency response www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 Rating -30~85 -40~85 10 27 E-mail:[email protected] Unit °C °C V dBm Page 3 of 11 SAW FILTER HDF4621 2-2 Input / Output VSWR Charts www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 4 of 11 SAW FILTER HDF4621 2-3Input / Output Smith Charts www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 5 of 11 SAW FILTER HDF4621 2-2.Electrical characteristics Minimum Center Frequency ( F0 ) MHz Insertion Loss (F0 +/- 2.5 MHz) Amplitude Ripple (F0 +/- 2.5 MHz) dB dB VSWR (F0 +/- 2.5 MHz) Relative Attenuation 0.3 MHz ~ 450.0 MHz 450.0 MHz ~ 455.0 MHz 482.0 MHz ~ 1200 MHz 1200 MHz ~ 1700 MHz 1700 MHz ~ 2000 MHz Input/Output Impedance - Typical 462.5 Maximum - - 3.0 3.5 - 1.0 2.0 - 1.5 2.0 - dB Ω Temperature Coefficient of Frequency ppm/°C 48 38 37 35 25 - 55 40 42 40 30 50 - - -32 - 3. TEST CIRCUIT 4. DIMENSION www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 6 of 11 SAW FILTER HDF4621 5. Environmental Performance Characteristics Item High temperature Low temperature Humidity Thermal shock Resistance to Soldering heat www.shoulder.cn Condition The specimen shall be store at a temperature of 85±2℃ for 96±4h. Then it shall be subjected to standard atmospheric conditions for 1h, after which measurement shall be made within 1h. The specimen shall be store at a temperature of -30±3℃ for 96±4h. Then it shall be subjected to standard atmospheric conditions for 1h, after which measurement shall be made within 1h. The specimen shall be store at a temperature of 40±2℃ with relative humidity of 90% to 96% for 96±4h. Then it shall be subjected to standard atmospheric conditions for 1h, after which measurement shall be made within 1h. The specimen shall be subjected to 8 continuous cycles each as shown below. Then it shall be subjected to standard atmospheric conditions for 1h, after which measurement shall be made within 1h. Temperature Duration 1 +25℃=>-40℃ 0.5h 2 -40℃ 4h 3 -40℃=>+85℃ 2h 4 +85℃ 4h 5 +85℃=>+25℃ 0.5h 6 +25℃ 1h Reflow soldering method Peak: 255 ±5 ℃, 220 ±5℃, 40s At electrode temperature of the specimen. Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Specifications Mechanical characteristics and specifications in electrical characteristics shall be satisfied. There shall be no excessive change in appearance. Page 7 of 11 SAW FILTER Solder ability HDF4621 The specimen shall be passed through the reflow furnace with the condition shown in the above profile for 1 time. The specimen shall be stored at standard atmospheric conditions for 1h, after which the measurement shall be made. Test board shall be 1.6 mm thick. Base material shall be glass fabric base epoxy resin. Immerse the pins melt solder at 260℃+5/-0℃ More then 95% of for 5 sec. total area of the pins should be covered with solder 6. Mechanical Test Items Vibration Drop Lead pull Lead bend Conditions 600-3300rpm amplitude 1.5mm 3 directions 2 H each On maple plate from 1m high 3 times Pull with 1kg force for 30 seconds 90o bending with 500g weigh 2 times Specifications There shall be no damage. 7. REMARK 7.1 Static voltage Static voltage between signal load & ground may cause deterioration &destruction of the component. Please avoid static voltage. 7.2 Ultrasonic cleaning Ultrasonic vibration may cause deterioration & destruction of the component. Please avoid ultrasonic cleaning 7.3 Soldering Only leads of component may be soldered. Please avoid soldering another part of component. www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 8 of 11 SAW FILTER HDF4621 8. Packing 8.1 Dimensions (1) Carrier Tape: Figure 1 (2) Reel: Figure 2 (3) The product shall be packed properly not to be damaged during transportation and storage. 8.2 Reeling Quantity 1000 pcs/reel 7’’ 3000 pcs/reel 13’’ 8.3 Taping Structure (1) The tape shall be wound around the reel in the direction shown below. (2) Label Device Name User Product Name Quantity Lot No. (3) Leader part and vacant position specifications. www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 9 of 11 SAW FILTER HDF4621 9. TAPE SPECIFICATIONS 9.1 Tensile Strength of Carrier Tape: 4.4N/mm width 9.2 Top Cover Tape Adhesion (See the below figure) (1) pull off angle: 0~15º (2) speed: 300mm/min. (3) force: 20~70g [Figure 1] Carrier Tape Dimensions [Unit:mm] W F E P0 P1 P2 D0 D1 t1 t2 A B 12.00 ±0.30 5.50 ±0.10 1.75 ±0.10 4.00 ±0.10 8.00 ±0.10 2.00 ±0.10 Ø1.50 Ø1.0 ±0.25 0.25 ±0.05 1.65 ±0.10 4.04 ±0.10 4.10 ±0.10 www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 10 of 11 SAW FILTER HDF4621 [Figure 2] [Unit:mm] A B C D E W t r Ø330 ±1.0 Ø100 ±0.5 Ø13 ±0.5 Ø21 ±0.8 2 ±0.5 13 ±0.3 3 max. 1.0 max. www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 11 of 11