规格书编号 SPEC NO : 产品 规 格书 SPECIFICATION CUSTOMER 客 户: PRODUCT 产 品: SAW FILTER MODEL NO 型 号: HDF56A F11 PREPARED 编 制: CHECKED 审 核: APPROVED 批 准: D A T E 日 期: 2006-5-11 客户确认 CUSTOMER RECEIVED: 审核 CHECKED 批准 APPROVED 日期 DATE 无锡市好达电子有限公司 Shoulder Electronics Limited www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 1 of 6 SAW FILTER HDF56A F11 更改历史记录 History Record 更改日期 Date www.shoulder.cn 规格书编号 Spec. No. 产品型号 Part No. 客户产品型号 Customer No. Tel:0755-82916880 Fax:0755-82916881 更改内容描述 Modify Content E-mail:[email protected] 备注 Remark Page 2 of 6 SAW FILTER HDF56A F11 1.SCOPE This specification shall cover the characteristics of SAW Filter with F56A used for the cordlessphone. 2.ELECTRICAL SPECIFICATION 2.1 Maximum Rating (Ta = 25 ℃) Characteristics Ratings Input signal voltage 5 between input between output Between others DC voltage AC voltage: 50-60 Hz Operating temperature rang Storage temperature range Unit Vp-p 3 15 V 10 Vp-p -20 – 70 -55 – 85 ℃ ℃ 2.2 Electrical Characteristics www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 3 of 6 SAW FILTER HDF56A F11 Description Center frequency(3dB) Fo Insertion loss 3dB Pass width Stop band attenuation 46.00~52.00MHz 60.00~66.00MHz min 55.80 type 56.00 max 56.2 4.0 +/-160 unit MHz dB kHz 25.0 20.0 dB dB 3. ENVIRONMENTAL PERFORMANCE CHARACTERISTICS Item Test condition Allowable change of absolute Level in pass band(dB) High temperature test 85℃ 500H < 1.0 Low temperature test -40℃ 500H <1.0 Humidity test 40℃ 90-95% 500H <1.0 Thermal shock -20℃==25℃==80℃ 5 cycle 30M 10M 30M <1.0 Solder temperature test Sold temp.260℃ for 10 sec. Soldering Immerse the pins melt solder at 260℃+5/-0℃ for 5 sec. www.shoulder.cn <1.0 More then 95% of total area of the pins should be covered with solder Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 4 of 6 SAW FILTER HDF56A F11 4.MECHANICAL TEST Item Test condition Allowable change of absolute Level in pass band(dB) Vibration test 600-3300rpm amplitude 1.5mm 3 directions 2 H each Drop test On maple plate from 1m high 3 times Lead pull test Pull with 1 kg force For 30 seconds Lead bend test 90°bending.with 500g weigh 2times <1.0 <1.0 <1.0 <1.0 5. VOLTAGE DISCHARGE TEST Item Test condition Allowable Chang of absolute Level in pass band(dB) Surge test Between any two electrode www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 <1.0 E-mail:[email protected] Page 5 of 6 SAW FILTER HDF56A F11 6.DIMENSION www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 6 of 6