Surface Mount Polymer ESD Suppressors ESD0201LC05N15 Description ESD0201LC05N15 is applied to electrostatic discharge (ESD) protection. It is designed to protect the high-speed data lines against ESD transients. It has very low capacitance and fast turn on times makes it ideal for data and transmission lines with high data rates. It can apply to HDMI, USB3.0, Display port, Thunderbolt, etc. Features u Protection against ESD voltages and currents (IEC61000-4-2 Level 4) u Equivalent Circuits Extremely quick response time (<1ns) present ideal ESD protection u Extremely low capacitance (0.05pF typical) u Bi-directional device u SMD (Surface Mount Device) u Zero signal distortion Electrical Characteristics Symbol Unit Min Typical Rated Voltage VDC V Trigger Voltage VT V 300 Clamping Voltage VC V 20 Capacitance, @1MHz CP pF 0.05 15 Response time ns ESD Voltage Capability, Contact Discharge Mode KV 8 ESD Voltage Capability, Air Discharge Mode KV 15 Pulses 1000 ESD Pulse Withstand Max. 1 VT - Measurement by using Transmission Line Pulse (TLP) VC - Measurement by using Transmission Line Pulse (TLP) CP - Device Capacitance measured with 1Vrms SOCAY Electronics Co., Ltd. Revision November 08, 2013 www.socay.com 1/4 @SOCAY Electronics Co., Ltd. 2013 Specifications are subject to change without notice. Please refer to www.socay.com for current information. Surface Mount Polymer ESD Suppressors ESD0201LC05N15 Explanation of Part Number ESD 0210 LC 05 N 15 (1) (2) (3) (4) (5) (6) (1) Series Type: ESD Guard TM Series (2) Chip Size (EIA): 0402 (3) Series Type: Extremely low capacitance CEMI / ESD Protection (4) Capacitance: Value - xx, 05=0.05pF (5) Capacitance Tolerance: N - ±30%, M - ±20% (6) Rated Voltage, VDC Construction & Dimensions Unit: mm Substrate Ceramic (Alumina) Symbol Spec. Encapsulate Polymer L 0.63±0.05 End termination Ag / Ni / Sn W 0.30±0.03 H 0.24±0.03 B 0.165±0.05 A 0.35±0.05 C 0.50±0.05 D 0.35±0.05 Recommended pad outline SOCAY Electronics Co., Ltd. Revision November 08, 2013 www.socay.com 2/4 @SOCAY Electronics Co., Ltd. 2013 Specifications are subject to change without notice. Please refer to www.socay.com for current information. Surface Mount Polymer ESD Suppressors ESD0201LC05N15 Temperature Specifications Environmental Specifications Item Thermal Shock Specifications Test Condition IL≤ 10μA -40°C to +85°C，30 min. cycle, 5 cycles High Temperature IL≤ 10μA Solder leach Resistance IL≤ 10μA Reference JIS C0025 (1998)Test Na Rated Voltage, 85°C, 1000hrs MIL-STD-202G Method 108 260°C, 10s MIL-STD-202G Method 210F Parameter Value Unit Operating Temperature -55 to +85 °C Storage Temperature --55 to +85 °C Storage Temperature 5 to 40 °C Relative Humidity <65 %RH Storage Time 12 Max Month Taping Package Storage Condition IL - Leakage current at rated voltage, the maximum leakage current was measured after reliability test. Construction & Dimensions Unit: mm Reflow Condition Pb free assembly TP Ramp-up Critical Zone TL to TP -Temperature Min (Ts(min)) +150°C -Temperature Max (Ts(max)) +200°C -Time (min to max) (TS) 60 -180 Seconds TL Pre Heat Temperature TS(max) Ramp-down TS(min) Average ramp up rate ( Liquidus Temp TL) to peak 3°C/Second Max TS(max) to TL - Ramp-up Rate 3°C/Second Max Preheat 25 Time to peak temperature (t 25℃ to peak) Time - Temperature (TL) (Liquidus) +217°C - Time (min to max) (TL) 60 -150 Seconds Reflow Precaution for soldering Note that this product will be easily damaged by rapid heating, rapid cooling or local heating. Do not give heat shock over 100°C in the process of soldering. We recommend to take preheating and gradual cooling Soldering gun procedure Note the follows, in case of using solder gun for replacement. 1) The tip temperature must be less than 280 for the period within 3 seconds by using soldering gun under 30W 2) The soldering gun tip shall not touch this product directly. Peak Temperature (TP) 260 +0/-5°C Time within 5°C of actual peak Temperature (TP) 20-40 Seconds Ramp-down Rate 6°C/Second Max Time 25°C to peak Temperature (TP) 8 minutes Max Soldering volume Note that excess of soldering volume will easily get crack the body of this product. SOCAY Electronics Co., Ltd. Revision November 08, 2013 www.socay.com 3/4 @SOCAY Electronics Co., Ltd. 2013 Specifications are subject to change without notice. Please refer to www.socay.com for current information. Surface Mount Polymer ESD Suppressors ESD0201LC05N15 Packaging Information Carrier Tape Dimensions Unit: mm Packaging method - Products shall be heat-sealed in the chip pocket, spacing Symbol 0201 A 8.00±0.30 B 3.50±0.05 C 1.75±0.10 D 2.00±0.05 E 4.00±0.10 F 1.50±0.10 L 0.69±0.03 W 0.39±0.03 T 0.42±0.03 pitch 2-mm of paper carrier tape with cover tape, and carrier tape shall be reeled to the reel. - Tape material to be paper. - Cover Tape adhesion to be 40±15 grams. Taping Reel Dimensions Taping Specifications Unit: mm There Shall be the portion having no product in both the head and the end of taping, and there shall be the cover tape in the heat of taping. Quantity of products in the taping package Standard Quantity 0201 15,000PCS / Reel Shipping quantity is a multiple of standard quantity SOCAY Electronics Co., Ltd. Revision November 08, 2013 www.socay.com 4/4 @SOCAY Electronics Co., Ltd. 2013 Specifications are subject to change without notice. Please refer to www.socay.com for current information.