M291 1 Form A 50V / 100mΩ MOSFET Output Solid State Relay Description Features The M291 is a bi-directional, single-pole, single-throw, normally open multipurpose solid-state relay in a miniature 4-pin small outline package. It is designed to be a costeffective replacement of reed relays in low voltage applications. The M291 has an extremely low on resistance of 70m (TYP) and a very high continuous load current rating of up to 2A. The combination of low onresistance, small package outline and high load current capabilities make the M291 a unique, unparalleled solid state relay. The M291 comes standard in a 4 pin SOP package. Low On Resistance (70m TYP) High Continuous Load Current (2A MAX) High Input-to-Output Isolation (1500V MIN) Ultra Miniature 4SOP Package Long Life / High Reliability RoHS / Pb-Free / REACH Compliant Agency Approvals UL/C-UL: VDE: File # E201932 File # 40035191 (EN 60747-5-2) Applications Reed Relay Replacement Security Systems Absolute Maximum Ratings Meter Reading Equipment Data Acquisition Battery Monitoring Multiplexers The values indicated are absolute stress ratings. Functional operation of the device is not implied at these or any conditions in excess of those defined in electrical characteristics section of this document. Exposure to absolute Maximum Ratings may cause permanent damage to the device and may adversely affect reliability. Schematic Diagram Storage Temperature …………………………..-55 to +125°C Operating Temperature …………………………-40 to +85°C Continuous Input Current ………………………………..50mA Transient Input Current ………………….……………..500mA Reverse Input Control Voltage …………..…………………5V Input Power Dissipation …………………………………40mW Total Power Dissipation ……………………………..400mW Solder Temperature – Wave (10sec)……………….….260°C Solder Temperature – IR Reflow (10sec)….…………..260°C Ordering Information Part Number M291 M291-TR Description 4 pin SOP, (100/Tube) 4 pin SOP, Tape and Reel (2000/Reel) NOTE: Suffixes listed above are not included in marking on device for part number identification © 2013 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 Page 1 of 7 M291/TR Rev 1.00 (03/06/2013) 001559 M291 1 Form A 50V / 100mΩ MOSFET Output Solid State Relay Electrical Characteristics, TA = 25°C (unless otherwise specified) Parameter Symbol Min. Typ. Max. 1.8 Units Test Conditions V IF = 10mA Input Specifications LED Forward Voltage VF - 1.4 LED Reverse Voltage BVR 5 - - V IR = 10μA Input Reverse Current IR - - 10 A VR = 5V Turn-On Current IF - 1 5 mA VO = 20V, IO = 100mA (within 5mS) VB 50 - - V IO=1A Output Specifications Blocking Voltage Continuous Load Current IO - - 2 On Resistance RON - 70 100 Leakage Current IOleak - 0.05 Output Capacitance A IF=5mA mΩ IF=5mA, IO=2A 1 A IF=0mA, VO=50V COUT - 20 - pF VO=25V, f=1.0MHz VOFFSET - - 0.2 mV IF=10mA Turn-On Time TON - 1 5 mS IF=5mA, VO=10V, IO=2A Turn-Off Time TOFF - 0.05 0.5 mS IF=0mA, VO=10V, IO=2A Offset Voltage Coupled Specifications Coupled Capacitance Contact Transient Ratio CCOUPLED - 2 - pF - 2,000 7,000 0 V/S VISO 1500 - - VRMS RH ≤ 50%, t=1min - VI-O = 500VDC dV = 50V Isolation Specifications Isolation Voltage Input-Output Resistance © 2013 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 RI-O - 10 Page 2 of 7 12 M291/TR Rev 1.00 (03/06/2013) 001559 M291 1 Form A 50V / 100mΩ MOSFET Output Solid State Relay M291 Performance & Characteristics Plots, TA = 25°C (unless otherwise specified) IF=5mA IO=2A IF=5mA IO=2A © 2013 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 Page 3 of 7 M291/TR Rev 1.00 (03/06/2013) 001559 M291 1 Form A 50V / 100mΩ MOSFET Output Solid State Relay M291 Solder Reflow Temperature Profile Recommendations (1) Infrared Reflow: Refer to the following figure as an example of an optimal temperature profile for single occurrence infrared reflow. Soldering process should not exceed temperature or time limits expressed herein. Surface temperature of device package should not exceed 250ºC: G F D E H B A C Process Step A B C D E F G H Description Preheat Start Temperature (ºC) Preheat Finish Temperature (ºC) Preheat Time (s) Melting Temperature (ºC) Time above Melting Temperature (s) Peak Temperature, at Terminal (ºC) Dwell Time at Peak Temperature (s) Cool-down (ºC/s) Parameter 150ºC 180ºC 90 - 120s 230ºC 30s 260ºC 10s <6ºC/s (2) Wave Solder: Maximum Temperature: Maximum Time: Pre-heating: Single Occurrence 260ºC (at terminal) 10s 100 - 150ºC (30 - 90s) (3) Hand Solder: Maximum Temperature: Maximum Time: Single Occurrence © 2013 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 350ºC 3s (at tip of soldering iron) Page 4 of 7 M291/TR Rev 1.00 (03/06/2013) 001559 M291 1 Form A 50V / 100mΩ MOSFET Output Solid State Relay M291 Package Dimensions 4 PIN SOP Package © 2013 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 Note: All dimensions in inches with millimeters [mm] in parenthesis () Page 5 of 7 M291/TR Rev 1.00 (03/06/2013) 001559 M291 1 Form A 50V / 100mΩ MOSFET Output Solid State Relay M291 Packaging Specifications Tape & Reel Specifications (T&R) © 2013 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 Note: Page 6 of 7 All dimensions in millimeters [mm] M291/TR Rev 1.00 (03/06/2013) 001559 M291 1 Form A 50V / 100mΩ MOSFET Output Solid State Relay M291 Package Marking M291 YYWW Date Code Pin 1 DISCLAIMER Solid State Optronics (SSO) makes no warranties or representations with regards to the completeness and accuracy of this document. SSO reserves the right to make changes to product description, specifications at any time without further notices. SSO shall not assume any liability arising out of the application or use of any product or circuit described herein. Neither circuit patent licenses nor indemnity are expressed or implied. Except as specified in SSO’s Standard Terms & Conditions, SSO disclaims liability for consequential or other damage, and we make no other warranty, expressed or implied, including merchantability and fitness for particular use. LIFE SUPPORT POLICY SSO does not authorize use of its devices in life support applications wherein failure or malfunction of a device may lead to personal injury or death. Users of SSO devices in life support applications assume all risks of such use and agree to indemnify SSO against any and all damages resulting from such use. Life support devices are defined as devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when used properly in accordance with instructions for use can be reasonably expected to result in significant injury to the user, or (d) a critical component of a life support device or system whose failure can be reasonably expected to cause failure of the life support device or system, or to affect its safety or effectiveness. © 2013 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 Page 7 of 7 M291/TR Rev 1.00 (03/06/2013) 001559