AD2C111 - Solid State Optronics

AD2C111
1 Form A
Solid State Relay
DESCRIPTION
The AD2C111 is a bi-directional, single-pole, single-throw, normally open multipurpose solid-state relay. It is designed to replace
electromechanical relays in general purpose switching applications. The relay consists of IR LED optically coupled to a IC that drives two
rugged source-to-source enhancement type DMOS transistors. The 4 pin DIP package offers the combination of reduced package size,
with 5kV input to output isolation.
FEATURES
APPLICATIONS
•
Small 4 pin DIP package outline - reduces board space
•
Reed relay replacement
•
High input-output isolation (5kVrms)
•
Meter reading systems
•
Low input control power consumption (2mA TYP)
•
Medical Equipment
•
130mA maximum continuous load current
•
Battery Monitoring
•
30 ohms maximum on-resistance
•
Multiplexers
•
Long life/high reliability
•
RoHS / Pb-Free / REACH Compliant
OPTIONS/SUFFIXES*
ABSOLUTE MAXIMUM RATINGS*
•
-S
Surface Mount Leadform Option (65pcs / tube)
•
-TR
Tape and Reel Packing Option (2,000 pcs / reel)
NOTE: Suffixes listed above are not included in marking on
device for part number identification.
SCHEMATIC DIAGRAM
+ INPUT
1
4
2
3
- INPUT
LOAD
LOAD
PARAMETER
UNIT
MIN
Storage Temperature
°C
-40
125
Operating Temperature
°C
-40
85
Continuous Input Current
mA
50
Transient Input Current
(1us)
mA
1
Reverse Input Control
Voltage
V
5
mW
500
Solder Temperature Wave (10s)
°C
260
Solder Temperature - IR
Reflow (10s)
°C
260
Output Power Dissipation
TYP
MAX
*The values indicated are absolute stress ratings. Functional operation of the
device is not implied at these or any conditions in excess of those defined in
electrical characteristics section of this document. Exposure to Absolute
Ratings may cause permanent damage to the device and may adversely
affect reliability.
APPROVALS
• UL / C-UL Approved: File # E201932
© 2011 Solid State Optronics • San José, CA
www.ssousa.com • +1.408.293.4600
Page 1 of 5
AD2C111
rev 1.43 (2/4/2011)
AD2C111
1 Form A
Solid State Relay
ELECTRICAL CHARACTERISTICS - 25°C
PARAMETER
UNIT
MIN
TYP
MAX
TEST CONDITIONS
1.8
2
If = 10mA
2
5
Io = 100mA, Vo=20V T=10ms
INPUT SPECIFICATIONS
LED Forward Voltage
V
Turn-On Current
mA
Turn-Off Current
mA
0.2
Blocking Voltage
V
400
Continuous Load Current
mA
On-Resistance
OUTPUT SPECIFICATIONS
Io = 1uA
130
If = 5mA
Ω
17
30
Io = 130mA
Output Off-State Leakage Current
µA
0.2
1
Vo = 400V
I/O Capacitance
pF
6
If=0, f = 1.0MHz
COUPLED SPECIFICATIONS
Isolation Voltage
V
Turn-On Time
ms
Turn-Off Time
ms
Isolation Resistance
© 2011 Solid State Optronics • San José, CA
www.ssousa.com • +1.408.293.4600
GΩ
5000
T = 1 min
1
2
If = 5mA, Io = 130mA
0.05
1
If = 0mA, Io = 130mA
100
Page 2 of 5
AD2C111
rev 1.43 (2/4/2011)
AD2C111
1 Form A
Solid State Relay
AD2C111
AD2C111
Typical Turn-On Time Distribution
N = 100, Ambient Temperature = 25°C
Typical Turn-Off Time Distribution
N = 100, Ambient Temperature = 25°C
50
60
50
40
30
20
10
0
Device Cou
40
30
20
10
0
0.6
0.8
1
1.2
1.4
1.6
1.8
0.02
0.03
0.06
0.07
0.08
AD2C111
Typical On-Resistance Distribution
N = 100, Ambient Temperature = 25°C
Typical Leakage Current Distribution
N = 100, Ambient Temperature = 25°C
50
40
40
30
20
10
0
15
16
17
18
19
20
30
20
10
0
21
0.04
0.045
On-Resistance (ohm s)
0.05
0.055
0.06
0.065
0.07
0.075
Leakage Current (uA)
AD2C111
AD2C111
Typical Blocking Voltage Distribution
N = 100, Ambient Temperature = 25°C
Maximum Load Current vs. Temperature
Blocking Voltage (V)
© 2011 Solid State Optronics • San José, CA
www.ssousa.com • +1.408.293.4600
100
50
80
60
0
0
-4
0
380 400 420 440 460 480 500 520
150
-2
0
60
50
40
30
20
10
0
Load Current (m
Device Cou
0.05
AD2C111
50
14
0.04
Turn-Off Tim e (m s)
Device Cou
Device Cou
Turn-On Tim e (m s)
40
0.4
20
Device Cou
PERFORMANCE DATA
Tem perature (C)
Page 3 of 5
AD2C111
rev 1.43 (2/4/2011)
AD2C111
1 Form A
Solid State Relay
MECHANICAL DIMENSIONS
4 PIN DUAL IN-LINE PACKAGE
4 PIN SURFACE MOUNT DEVICE
END VIEW
END VIEW
TOP VIEW
TOP VIEW
BOTTOM VIEW
BOTTOM VIEW
© 2011 Solid State Optronics • San José, CA
www.ssousa.com • +1.408.293.4600
Page 4 of 5
AD2C111
rev 1.43 (2/4/2011)
AD2C111
1 Form A
Solid State Relay
DISCLAIMER
Solid State Optronics (SSO) makes no warranties or representations with regards to the completeness and accuracy of this document. SSO
reserves the right to make changes to product description, specifications at any time without further notice.
SSO shall not assume any liability arising out of the application or use of any product or circuit described herein. Neither circuit patent
licenses nor indemnity are expressed or implied.
Except as specified in SSO's Standard Terms & Conditions, SSO disclaims liability for consequential or other damage, and we make no other
warranty, expressed or implied, including merchantability and fitness for particular use.
LIFE SUPPORT POLICY
SSO does not authorize use of its devices in life support applications wherein failure or malfunction of a device may lead to personal injury or
death. Users of SSO devices in life support applications assume all risks of such use and agree to indemnify SSO against any and all
damages resulting from such use. Life support devices are defined as devices or systems which, (a) are intended for surgical implant into the
body, or (b) support or sustain life, and (c) whose failure to perform when used properly in accordance with instructions for use can be
reasonably expected to result in significant injury to the user, or (d) a critical component in any component of a life support device or system
whose failure can be reasonably expected to cause failure of the life support device or system, or to affect its safety or effectiveness.
© 2011 Solid State Optronics • San José, CA
www.ssousa.com • +1.408.293.4600
Page 5 of 5
AD2C111
rev 1.43 (2/4/2011)