TD3052 Random Switching Triac Driver DESCRIPTION The TD3052 consists of an AlGaAs LED optically coupled to a Random Phase triac driver chip. The TD3052 provides high input-tooutput isolation and is designed to drive high-powered triacs. Typical uses include interfacing logic level control signals to equipment powered from 110Vac and 220Vac lines. FEATURES APPLICATIONS • Random phase switching • Home appliances • 600V blocking voltage • Motor control • High input-to-output isolation (5kV MIN) • Solid state relays • 10mA turn-on (trigger) current • Valve control • High reliability • Solenoids • Dimmers • High Power Triacs OPTIONS/SUFFIXES* ABSOLUTE MAXIMUM RATINGS* • -H 0.4" Lead spacing (see mechanical dimensio • -S Surface Mount Leadform Option • -TR Tape and Reel Option • -V Signifies VDE approval NOTE: Suffixes listed above are not included in marking on device for part number identification. SCHEMATIC DIAGRAM 1 6 2 5 3 4 + Input - Input +/- AC Output Do Not Use -/+ AC Output PARAMETER UNIT MIN Storage Temperature °C -55 125 Operating Temperature °C -40 85 Continuous Input Current mA 40 Transient Input Current mA 400 Reverse Input Control Voltage V Output Power Dissipation mW TYP MAX 6 500 *The values indicated are absolute stress ratings. Functional operation of the device is not implied at these or any conditions in excess of those defined in electrical characteristics section of this document. Exposure to Absolute Ratings may cause permanent damage to the device and may adversely affect reliability. APPROVALS © 2004 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 • UL / C-UL Approved File #E201932 • VDE Approved, Lic # 40011225 Page 1 of 5 TD3052 rev 1.40 (10/25/2004) TD3052 Random Switching Triac Driver ELECTRICAL CHARACTERISTICS - 25°C PARAMETER UNIT MIN TYP MAX 1.2 1.5 TEST CONDITIONS INPUT SPECIFICATIONS LED Forward Voltage V LED Reverse Voltage 6 V 12 Turn-On Current mA 5 Turn-Off Current mA 0.5 If = 10mA Ir = 10uA 10 Io = 100mA OUTPUT SPECIFICATIONS Blocking Voltage V Continuous Load Current mA Holding Current µA Leakage Current µA On-State Voltage V Critical Rate of Rise V/ 600 Io = 1uA 100 Iin = 5mA 1 Vo =600V 3 Iin = 5mA 250 2 µs 1000 1500 COUPLED SPECIFICATIONS Isolation Voltage V Coupled Capacitance pF 5000 T = 1 minute 2 STATIC dV/dt TEST CIRCUIT 400V Vdc RTEST R = 1 kΩ CTEST 200pF PULSE INPUT MERCURY WETTED RELAY D.U.T. X100 SCOPE PROBE Vmax = 400 V APPLIED VOLTAGE WAVEFORM 252 V dv/dt = 0 VOLTS 0.63 Vmax RC = 252 RC RC © 2004 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 Page 2 of 5 TD3052 rev 1.40 (10/25/2004) TD3052 Random Switching Triac Driver TD3052 TD3052 Maximum Load Current vs. Temperature Typical Blocking Voltage Distribution N = 100, Ambient Temperature = 25°C 60 50 40 30 20 10 0 600 610 620 630 640 650 660 670 80 60 40 20 0 -2 0 Device Count 120 100 80 60 40 20 0 -4 0 Load Current (mA) PERFORMANCE DATA Blocking Voltage (V) Tem perature (C) TD3052 On-State Characteristics ITM,ON-STATE CURRENT (mA) IDRM1,PEAK BLOCKING CURRENT (nA) TD3052; Leakage with LED Off vs. Temperature Ta,AMBIENT TEMPERATURE (°C) VTM, ON-STATE VOLTAGE(VOLTS) IFT , NORMALIZED TD3052: Trigger Current vs. Temperature Ta,AMBIENT TEMPERATURE (°C) © 2004 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 Page 3 of 5 TD3052 rev 1.40 (10/25/2004) TD3052 Random Switching Triac Driver MECHANICAL DIMENSIONS 6 PIN DUAL-IN-LINE PACKAGE (Through-hole) 6 PIN SURFACE MOUNT DEVICE (SMD) TOLERANCE :+ 0.25mm -H Suffix (0.4" / 10mm Lead Spacing) Unit (mm) © 2004 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 Page 4 of 5 TD3052 rev 1.40 (10/25/2004) TD3052 Random Switching Triac Driver DISCLAIMER Solid State Optronics (SSO) makes no warranties or representations with regards to the completeness and accuracy of this document. SSO reserves the right to make changes to product description, specifications at any time without further notice. SSO shall not assume any liability arising out of the application or use of any product or circuit described herein. Neither circuit patent licenses nor indemnity are expressed or implied. Except as specified in SSO's Standard Terms & Conditions, SSO disclaims liability for consequential or other damage, and we make no other warranty, expressed or implied, including merchantability and fitness for particular use. LIFE SUPPORT POLICY SSO does not authorize use of its devices in life support applications wherein failure or malfunction of a device may lead to personal injury or death. Users of SSO devices in life support applications assume all risks of such use and agree to indemnify SSO against any and all damages resulting from such use. Life support devices are defined as devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when used properly in accordance with instructions for use can be reasonably expected to result in significant injury to the user, or (d) a critical component in any component of a life support device or system whose failure can be reasonably expected to cause failure of the life support device or system, or to affect its safety or effectiveness. © 2004 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 Page 5 of 5 TD3052 rev 1.40 (10/25/2004)