AD6C211-L 1 Form A, Current Limiting 400V / 25 Ω MOSFET Output Solid State Relay Description Features The AD6C211-L is a bi-directional, single-pole, singlethrow, normally open solid-state relay. It provides a load current of 150mA, a high blocking voltage of 400V, and current limiting circuitry in a compact 6 pin DIP package. Current limiting circuitry provides a level of protection against increased load currents or transient current spikes by active current reduction across the device, thereby protecting itself and downstream components. High Isolation Voltage (3750VRMS) Low Input Control Current (3mA TYP) 150mA Maximum Continuous Load Current 25 Maximum On-Resistance Active Current Limiting Protection Long Life / High Reliability RoHS / Pb-Free / REACH Compliant The AD6C211-L comes standard in a miniature 6 pin DIP package making it ideal for high-density board applications. Agency Approvals Applications UL / C-UL: VDE: Reed Relay Replacement Multiplexers Meter Reading Systems Medical Equipment Battery Monitoring Absolute Maximum Ratings The values indicated are absolute stress ratings. Functional operation of the device is not implied at these or any conditions in excess of those defined in electrical characteristics section of this document. Exposure to absolute Maximum Ratings may cause permanent damage to the device and may adversely affect reliability. Schematic Diagram (+) Input 1 (-) Input 2 File # E201932 File # 40035191 (EN 60747-5-2) 6 -/+ Load 5 DC Connection 4 -/+ Load Storage Temperature …………………………..-55 to +125°C Operating Temperature …………………………-40 to +85°C Continuous Input Current ………………………………..50mA Transient Input Current ………………….……………..500mA Reverse Input Control Voltage …………..…………………6V Input Power Dissipation …………………………………40mW Output Power Dissipation ……………………………..800mW Solder Temperature – Wave (10sec)……………….….260°C Solder Temperature – IR Reflow (10sec)….…………..260°C ILIMIT Do Not Use 3 Ordering Information Part Number AD6C211-L AD6C211-L AD6C211-LS AD6C211-LSTR Description 6 pin DIP, (50/Tube) 6 pin SMD, (50/Tube) 6 pin SMD, Tape and Reel (1000/Reel) NOTE: Suffixes listed above are not included in marking on device for part number identification © 2012 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 Page 1 of 9 AD6C211-L/S/TR Rev 2.00 (08/28/2012) 001521 AD6C211-L 1 Form A, Current Limiting 400V / 25 Ω MOSFET Output Solid State Relay Electrical Characteristics, TA = 25°C (unless otherwise specified) Parameter Symbol Min. Typ. Max. Units Test Conditions Input Specifications LED Forward Voltage VF - 1.2 1.5 V IF = 10mA LED Reverse Voltage BVR 6 - - V IR = 10μA Turn-On Current IF - 3 5 mA IO = 150mA Turn-Off Current IFOFF - 0.5 - mA - Blocking Voltage VB 400 - - V IO=1A Continuous Load Current IO - - 150 mA IF=5mA Current Limit (AC or DC connection) ILIMIT 180 300 - mA IF=5mA On Resistance RON - 18 25 Ω IF=5mA, IO=150mA Leakage Current IOleak - 0.2 1 A IF=0mA, VO=400V Output Specifications Output Capacitance COUT - 25 50 pF IF=0mA, f=1.0MHz VOFFSET - - 0.2 mV IF=5mA Turn-On Time TON - 1.5 5.0 mS IF=5mA, IO=150mA Turn-Off Time TOFF - 0.5 1.0 mS IF=0mA, IO=150mA Offset Voltage Coupled Specifications Coupled Capacitance Contact Transient Ratio CCOUPLED - 3 - pF - 2,000 7,000 0 V/S VISO 3,750 - - VRMS RH ≤ 50%, t=1min - VI-O = 500VDC dV = 50V Isolation Specifications Isolation Voltage Input-Output Resistance © 2012 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 RI-O - 10 Page 2 of 9 12 AD6C211-L/S/TR Rev 2.00 (08/28/2012) 001521 AD6C211-L 1 Form A, Current Limiting 400V / 25 Ω MOSFET Output Solid State Relay AD6C211-L Current Limiting Connection Diagrams, TA = 25°C (unless otherwise specified) Connection Diagrams Comments Option A: Normal AC Load Configuration On Resistance: RTYP Current Limit: ILIMIT Option B: Separate Loads & Load Voltages On Resistance: Load1 Load2 Current Limit: Load1 Load2 ~ (RTYP / 2) + 3 RTYP / 2 ILIMIT N/A - Sum power of loads not to exceed maximum package power dissipation Option C: DC Load with Minimal Resistance and No Current Limit On Resistance: Current Limit: © 2012 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 Page 3 of 9 RTYP / 4 None AD6C211-L/S/TR Rev 2.00 (08/28/2012) 001521 AD6C211-L 1 Form A, Current Limiting 400V / 25 Ω MOSFET Output Solid State Relay AD6C211-L Performance & Characteristics Plots, TA = 25°C (unless otherwise specified) I =5mA F I =150mA O I =5mA F I =150mA O © 2012 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 Page 4 of 9 AD6C211-L/S/TR Rev 2.00 (08/28/2012) 001521 AD6C211-L 1 Form A, Current Limiting 400V / 25 Ω MOSFET Output Solid State Relay AD6C211-L Solder Temperature Profile Recommendations (1) Infrared Reflow: Refer to the following figure as an example of an optimal temperature profile for single occurrence infrared reflow. Soldering process should not exceed temperature or time limits expressed herein. Surface temperature of device package should not exceed 250ºC: G F D E H B A C Figure 1 Process Step A B C D E F G H Description Preheat Start Temperature (ºC) Preheat Finish Temperature (ºC) Preheat Time (s) Melting Temperature (ºC) Time above Melting Temperature (s) Peak Temperature, at Terminal (ºC) Dwell Time at Peak Temperature (s) Cool-down (ºC/s) Parameter 150ºC 180ºC 90 - 120s 230ºC 30s 260ºC 10s <6ºC/s (2) Wave Solder: Maximum Temperature: Maximum Time: Pre-heating: Single Occurrence 260ºC (at terminal) 10s 100 - 150ºC (30 - 90s) (3) Hand Solder: Maximum Temperature: Maximum Time: Single Occurrence © 2012 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 350ºC 3s (at tip of soldering iron) Page 5 of 9 AD6C211-L/S/TR Rev 2.00 (08/28/2012) 001521 AD6C211-L 1 Form A, Current Limiting 400V / 25 Ω MOSFET Output Solid State Relay AD6C211-L Package Dimensions 6 PIN DIP Package © 2012 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 Note: Page 6 of 9 All dimensions in inches [“] with millimeters in parenthesis () Device Weight: 0.45g AD6C211-L/S/TR Rev 2.00 (08/28/2012) 001521 AD6C211-L 1 Form A, Current Limiting 400V / 25 Ω MOSFET Output Solid State Relay AD6C211-L Package Dimensions 6 PIN SMD Surface Mount Package (-S) © 2012 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 Note: Page 7 of 9 All dimensions in inches [“] with millimeters in parenthesis () Device Weight: 0.45g AD6C211-L/S/TR Rev 2.00 (08/28/2012) 001521 AD6C211-L 1 Form A, Current Limiting 400V / 25 Ω MOSFET Output Solid State Relay AD6C211-L Package Dimensions 6 PIN SMD Tape & Reel (-STR) © 2012 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 Note: Page 8 of 9 All dimensions in millimeters AD6C211-L/S/TR Rev 2.00 (08/28/2012) 001521 AD6C211-L 1 Form A, Current Limiting 400V / 25 Ω MOSFET Output Solid State Relay AD6C211-L Package Marking AD6C211-L YYWW Date Code Pin 1 DISCLAIMER Solid State Optronics (SSO) makes no warranties or representations with regards to the completeness and accuracy of this document. SSO reserves the right to make changes to product description, specifications at any time without further notices. SSO shall not assume any liability arising out of the application or use of any product or circuit described herein. Neither circuit patent licenses nor indemnity are expressed or implied. Except as specified in SSO’s Standard Terms & Conditions, SSO disclaims liability for consequential or other damage, and we make no other warranty, expressed or implied, including merchantability and fitness for particular use. LIFE SUPPORT POLICY SSO does not authorize use of its devices in life support applications wherein failure or malfunction of a device may lead to personal injury or death. Users of SSO devices in life support applications assume all risks of such use and agree to indemnify SSO against any and all damages resulting from such use. Life support devices are defined as devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when used properly in accordance with instructions for use can be reasonably expected to result in significant injury to the user, or (d) a critical component of a life support device or system whose failure can be reasonably expected to cause failure of the life support device or system, or to affect its safety or effectiveness. © 2012 Solid State Optronics • San José, CA www.ssousa.com • +1.408.293.4600 Page 9 of 9 AD6C211-L/S/TR Rev 2.00 (08/28/2012) 001521