TECHNICAL DATA SL33193 Automotive Direction Indicator The SL33193 is a new generation industry standard UAA1041 “Flasher”. It has been developed for enhanced EMI sensitivity, system reliability, and improved wiring simplification. The SL33193 is pin compatible with the UAA1041 and UAA1041B in the standard application configuration as shown in Figure 9, without lamp short circuit detection and using a 20 mΩ shunt resistor. The SL33193 has a standby mode of operation requiring very low standby supply current and can be directly connected to the vehicle’s battery. It includes an RF filter on the Fault detection pin (Pin 7) for EMI purposes. Fault detection thresholds are reduced relative to those of the UAA1041, allowing a lower shunt resistance value (20 mW) to be used. ORDERING INFORMATION SL33193N DIP SL33193D SOIC TA = -40° to 125°C for all packages • Pin Compatible with the UAA1041 • Defective Lamp Detection Threshold • RF Filter for EMI Purposes • Load Dump Protection • Double Battery Capability for Jump Start PIN CONNECTIONS Vss 1 8 Starter Vсс 2 7 Fault Detector Relay 3 Oscillator 4 6 Enable 5 Oscillator Simplified Block Diagram 1 SW2 8 Starter SW1 2 3 Detector 24V 33V Reference Voltage RF Filter 7 6 Relay Driver Lamp Fault Detector 4 5 Oscillator This Device contains 60 active transistors. SLS System Logic Semiconductor 1 SL33193 MAXIMUM RATINGS* Rating Simbol Value Unit Pin1 Positive Current (Continious/Pulse) I1+ 150 to 500 mA Pin1 Negative Current (Continious/Pulse) I1- -35 to -500 mA Current (Continious/Pulse) I2 ±350 to ±1900 mA Current (Continious/Pulse) I3 ±300 to ±1400 mA Current (Continious/Pulse) I8 ±25 to ±50 mA ESD(Aii Pins Except Pin4 for Negative Pulse) VESD ±2000 °V ESD(Pin 4 Negative Pulse) VESD4- -1000 °V Jinction Temperature TJ 150 °C Operation Ambient Temperature Range TA -40 to +125 °C TSTG -65 to +150 °C Storage Temperature Range ELECTRICAL CHARACTERISTICS (-45OC ≤ TA ≤ +125 OC, 8.0 V ≤ VCC ≤ 18.0 V, unless otherwise noted. Typical values reflect approximate mean at TA= 25 OC, VCC = 14 V at the time of initial device characterization.) Characteristic Battery Voltage Range (Normal Operation) Overvoltage Detector Threshold (VPin2 – VPin1) Clamping Voltage (R2 = 220 Ω) Output Voltage [I = -250 mA (VPin2 – VPin3)] Starter Resistance (Rst = R2 +RLamp) Oscillator Constant (Normal Operation, TA= 25 OC) Temperature Coefficient of Kn Duty Cycle (Normal Operation) Oscillator Constant (One 21 W Lamp Defect, TA= 25OC) Duty Cycle(One 21 W Lamp Defect) Oscillator Constant (TA= 25 OC) Standby Current (Ignition «Off») Current Consumption (Relay «Off», Enable Pin 6 High) Vbat = 13.5 V, R3 = 220 Ω Current Consumption (Relay «On») Vbat = 13.5 V, R3 = 220 Ω Defect Lamp Detector [R3 = 220 Ω, (VPin2 – VPin7)] Vbat = 13.5 V SLS Symbol Vb Vih Vcl Vsat Rst Kn TCKn Kf K1 K2 ICC ICC Min 8.0 19 27 1.3 45 0.59 35 0.150 0.200 - Max 18 22 34 1.5 3.6 1.75 55 0.75 45 0.240 0.290 100 3.5 Unit V V V V kΩ ICC - 6.0 mA VS 42.5 56 mV 1/ OC % % µA mA System Logic Semiconductor 2 SL33193 Vbat Vbat «On»«Off» «On» «Off» tf t1 tn Ft=1/tf Fn=1/tn TIME Figure 1 - Normal Operation Oscillator Timing Diagram TIME Figure 2 - One Defective Lamp Oscillator Timing Diagram INTRODUCTION The SL33193 is designed to drive the direction indicator flasher relay. It is a new generation industry standard UAA1041 “Flasher”. It consists of the following functions: • Supply and Protections • On–Chip Relay Driver • Oscillator • Starter Functions • Lamp Fault Detector with Internal RF Filter • Standby Mode Supply and Protection Systems Pin 1 is connected to ground via resistor R3 which limits he current in the event of any high voltage transients. Pin 2 (VCC) is the positive supply and may be connected directly to the vehicle’s battery voltage. Overvoltage and Double Battery Protection: When the applied VCC to VSS voltage is greater than 22 V, the overvoltage detector circuit turns the relay driver off. Both the device and the lamps are protected if two 12 V batteries are connected in series and used to jump start the vehicle.Load Dump Overvoltage Protection: A 29 V overvoltage detector protects the circuits against high voltage transients due to load dumps and other low energy spikes. The relay driver is automatically turned on whenever the VCC to VSS voltage is greater than 34 V. Overvoltage Protection, High Voltage Transients: The Enable and the Starter pins are protected against positive and negative transients by internal on–chip diodes. On–Chip Relay Driver The device directly drives the flasher relay. The output structure is an Emitter of an NPN transistor. It contains the free wheeling diode circuitry necessary to protect the device whenever the relay is switched off. Oscillator The device uses a sawtooth oscillator (Figure 1). The frequency is determined by the external components C1 and R1. In the normal operating mode, the flashing frequency is: Fn = 1/R1*C1*Kn. With a defective (open) 21 W lamp (Figure 2), the flashing frequency changes to: Fn = 2.2*Fn. The typical first flash delay (the time between the moment when the indicator switch is closed and the first lamp flash occurs) is: t1 = K1*R1*C1 The fault detection delay is from the time relay R1 is on and fault detection is enabled. Where a 21 W lamp opens, the delay is expressed as: t2 = K2*R1*C1 SLS System Logic Semiconductor 3 SL33193 Starter Pin 8 is connected through a 3.3 kW resistor to the flashing lamp. Pin 8 is the input to the Starter function and senses the use of S1 by sensing ground through the lamp (Figures 9 and 10). Lamp Fault Detector with Internal RF Filter A Lamp defect is sensed by the lamp fault detector’s monitoring of the voltage developed across the external shunt resistor RS via the RF filter. The RS voltage drop is compared to a Vbat dependent internal reference voltage (Vref) to validate the comparison over the full battery voltage range. A detected fault causes the oscillator to change frequency (Figure 2). Standby Mode When the ignition key and warning switches are open; Enable is in a low state and the internal switches, SW1 and SW2, are open and no current passes through the circuit. In this condition, the device’s current consumption is zero (ICC = 0). When ignition key and warning switches are closed; Enable is in a high state with SW1 and SW2 being closed and the circuit is powered on. Main differences between UAA1041B & SL33193 The SL33193 is pin compatible with the UAA1041. Supply Current Supply current is more stable on the SL33193 when the device is in “on” or “off” state. In “on” state the supply current is only 40% higher than when in the “off” state, as compared to a ratio of 3 times for the UAA1041. This results in a lowern voltage drop across the ground resistor R3 (see On–Chip Relay Driver). Short Circuit Detection The SL33193 has no short circuit detection. Standby Mode (Pin 6) The UAA1041 has no standby mode. Pin 6 is used as an Enable/Disable for the short circuit detection. The SL33193 uses Pin 6 to set the device in standby mode. If Pin 6 is connected to ground, the SL33193 is in the standby mode. In this mode, standby current is very low and Pin 8’s starter resistor R2 and a 2.0 kW internal resistor are switched off. As soon as Pin 6 is at a high level (typical threshold = 2Vbe) the device becomes active. In the application, the SL33193 can be connected directly to the battery and awakened whenever Pin 6 is connected to the vehicle’s battery by way of a protection resistor and the ignition key switch. Lamp Defect Detection (Pin 7) The UAA1041 operates with a 30 mW shunt resistor to sense the lamp current. It’s lamp defect detection threshold of Pin 7 is typically 85 mV. The SL33193 is designed to operate with 20 mW shunt resistor and at a reduced threshold of 50 mV. This reduces power generation in the flasher module. In addition, the SL33193 incorporates an RF filter to enhance RFI immunity. Load Dump and Overvoltage Behavior The UAA1041 and SL33193 both behave the same in this regard. Both have double battery detection and lamp turn–off protection in the event of a jump start. During load dump, both devices are protected by an internal 30 V zener diode with the relay activated during a load dump. Relay Driver Drive capability of both devices is the same. Free wheeling diode protection is internal to both devices. The free wheeling voltage is 2Vbe for the UAA1041 and 3Vbe for the SL33193. This results in a higher clamp voltage across the relay and thus in a faster turn–off. In addition, the lower “on” state supply current is lower on the SL33193 and thus the voltage drop across the ground resistor R3 is reduced. This results in an even higher clamp voltage across the relay. Oscillator Phase The oscillator phase is opposite on the SL33193 as compared to the UAA1041. The Oscillator voltage is falling during “on” state and rising during “off” state for the SL33193. SLS System Logic Semiconductor 4 SL33193 Vcl, CLAMPING VOLTAGE (V) Vih, OVERVOLTAGE DETECT THRESHOLD (V) TA, AMBIENT TEMPERATURE (OC) TA, AMBIENT TEMPERATURE (OC) Figure 3 – Clamping Voltage versus Temperature Figure 4 – Overvoltage Detector versus Temperature ICC, SUPPLY CURRENT (mA) Vsat, OUTPUT VOLTAGE (V) Vbat = 13.5B R2 = 220 Ω Vbat = 13.5V I = 250 mA Relay Relay «Off» TA, AMBIENT TEMPERATURE (OC) TA, AMBIENT TEMPERATURE (OC) Figure 5 – Supply Current versus Temperature Figure 6 – Output Voltage versus Temperature LAMP DEFECT DETECTION THRESHOLD (mV) Kf, OSCILLATOR CONSTANT (TIMES) Vbat = 13.5V R2 = 220 Ω TA, AMBIENT TEMPERATURE (OC) TA, AMBIENT TEMPERATURE (OC) Figure 7 – Defect Lamp Detection versus Temperature Figure 8 – Oscillator Constant versus Temperature SLS System Logic Semiconductor 5 SL33193 1 8 2 Rs 7 IL33193 SL33193 C1 6 3 Vbat R2 4 5 R3 R1 Relay S1 L6 L2 L3 L4 L5 Rs = 20 mΩ R1 = 75 kΩ C1 = 5.6 µF R2 = 3.3 kΩ R3 = 200 Ω L2, L3, L4, L5 = 21 W Tum Signal Lamps Figure 9 - SL33193 Typical Application Application Information NOTES: 1. In the above application, the SL33193 is compatible with the UAA1041 and UAA1041B except for the shunt resistor value (Rs = 20 mΩ). 2. The flashing cycle is started by the closing of switch S1. 3. The position of switch S1 is sensed across resistor R2 and RLamp by the input, Pin 8. SLS System Logic Semiconductor 6 SL33193 Vbat Rs 1 SW2 R3 2 8 Starter SW1 Detector 24V 33V Reference Voltage RF Filter 7 Ignition Key С1 3 Relay Driver R4 6 Lamp Fault Detector R5 4 5 Waming Oscillator R2 R1 Relay 1 Relay 2 EXTERNAL COMPONENTS Rs = 20 mΩ R1 = 75 kΩ C1 = 5.6 µF R2 = 2.2 kΩ R3 = 220 Ω 10 kΩ ≤ R4 ≤ 47 kΩ 10 kΩ ≤ R5 ≤ 47 kΩ Relay 1 L1, L2, L3, L4 = 21W LD Dashboard Indicator Left LD L1 L2 S1 Direction Indicator Right L3 L4 LD Figure 10. SL33193 Typical Application Application Information Notes: 1.The flashing cycle is started by the dosing of switch S1. 2.The S1 switch position is sensed across the resistor R2 and RLAMP by the input (Pin8). 3. If the logic state at Pin6 is [0], the current through R2 is off. SLS System Logic Semiconductor 7 SL33193 N SUFFIX PLASTIC DIP (MS – 001BA) A Dimension, mm 5 8 B 1 4 F Symbol MIN MAX A 8.51 10.16 B 6.1 7.11 5.33 C L C D 0.36 0.56 F 1.14 1.78 -T- SEATING PLANE N G M K 0.25 (0.010) M J H D T NOTES: 1. Dimensions “A”, “B” do not include mold flash or protrusions. Maximum mold flash or protrusions 0.25 mm (0.010) per side. G 2.54 H 7.62 J 0° 10° K 2.92 3.81 L 7.62 8.26 M 0.2 0.36 N 0.38 D SUFFIX SOIC (MS - 012AA) Dimension, mm A 8 5 B H 1 G P 4 D K SEATING PLANE J F 0.25 (0.010) M T C M NOTES: 1. Dimensions A and B do not include mold flash or protrusion. 2. Maximum mold flash or protrusion 0.15 mm (0.006) per side for A; for B ‑ 0.25 mm (0.010) per side. SLS MIN MAX A 4.8 5 B 3.8 4 C 1.35 1.75 D 0.33 0.51 F 0.4 1.27 R x 45 C -T- Symbol M G 1.27 H 5.72 J 0° 8° K 0.1 0.25 M 0.19 0.25 P 5.8 6.2 R 0.25 0.5 System Logic Semiconductor 8