DATA SHEET SE2613T: 2.4 GHz Wireless LAN/BT Front-End Applications Product Description The SE2613T is a complete 802.11 b/g/n WLAN RF front-end module with a Bluetooth port. The device provides all the functionality of the power amplifier, power detector, harmonic filtering, switch, low noise amplifier, and associated matching. The SE2613T provides a complete 2.4 GHz WLAN RF solution from the output of the transceiver to the antenna, and from the antenna to the input of the transceiver, in an ultra compact form factor. IEEE802.11b DSSS WLAN IEEE802.11g,n OFDM WLAN Embedded applications with Bluetooth (Mobile) Features Dual Mode IEEE802.11b & IEEE802.11g Integrated PA, Harmonic Filter, LNA and BT port Integrated Positive Slope Power Detector 17.5 dBm @ 4.0 % EVM, 802.11g, 54 Mbps Direct connection to battery with 3.6 V nominal supply Lead free, Halogen free and RoHS compliant Compact package, 3 x 3 x 0.6 mm, MSL 1 The SE2613T is designed for ease of use, with all the critical matching and harmonic filtering integrated, also offering a simple 50 Ω interface to the antenna. The SE2613T includes a low noise amplifier to increase the receive sensitivity of embedded solutions to improve range or to overcome the insertion loss of cellular filters often included for mobile applications. Ordering Information Part No. Package Remark SE2613T SE2613T-R SE2613T-EK1 16 pin QFN 16 pin QFN N/A Samples Tape and Reel Evaluation kit The SE2613T also includes a transmitter power detector with 20 dB of dynamic range and a digital enable control for transmitter power ramp on/off control. DET Functional Block Diagram VCC2 VCC1 TX PEN BT ANT VDD LEN CBT CRX RX Figure 1: Functional Block Diagram Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202406A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 24, 2012 1 DATA SHEET SE2613T: 2.4 GHz Wireless LAN/BT Front-End 7 8 GND RX 12 11 CBT 6 CRX 10 GND 5 BT LEN 9 ANT 2 1 13 PEN TX 14 NC VCC1 15 3 DET 16 4 VCC2 NC Pin Out Diagram VDD Figure 2: SE2613T Pin out (Top View through Package) Pin Out Description Pin No. Name Description 1 Vcc2 PA Positive Power supply 2 DET Power Detector Output 3 Vcc1 PA Positive Power supply 4 TX Transmit port 5 NC Not connected 6 PEN PA enable control input 7 GND Ground 8 RX 9 VDD Receive port LNA and Switch Positive Power supply 10 LEN LNA enable control input 11 CRX Receive antenna switch control 12 BT Bluetooth port 13 CBT Bluetooth antenna switch control 14 GND Ground 15 ANT Antenna port 16 NC Not connected Die paddle GND Ground Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202406A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 24, 2012 2 DATA SHEET SE2613T: 2.4 GHz Wireless LAN/BT Front-End Absolute Maximum Ratings These are stress ratings only. Exposure to stresses beyond these maximum ratings (one rating applied at a time) for extended periods may cause permanent damage to, or affect the reliability of the device. Avoid operating the device outside the recommended operating conditions defined below. This device is ESD sensitive. Handling and assembly of this device should be at ESD protected workstations. Symbol Definition Min. Max. Unit VCC PA Supply Voltage on VCC1, VCC2 -0.3 6.0 V VDD LNA and Switch Supply Voltage -0.3 3.6 V DC input on control pins -0.3 3.6 V - 5 dBm Operating Temperature Range -40 85 °C Storage Temperature Range -40 150 °C VIN PTXIN TA TSTG ESD HBM TX Input Power, ANT terminated in 50Ω match JEDEC JESD22-A114 All pins V 1000 Recommended Operating Conditions Symbol Parameter Min. Typ. Max. Unit TA Ambient temperature -40 25 85 °C VCC PA Supply voltage, relative to GND = 0 V 2.7 3.6 4.8 V VDD LNA supply voltage, relative to GND = 0 V 2.7 3.3 3.6 V DC Electrical Characteristics Conditions: VCC = 3.6V, PEN = VDD= 3.3 V, TA = 25 °C, as measured on Skyworks Solutions’ SE2613T-EK1 evaluation board (de-embedded to device), all unused ports terminated with 50 ohms, unless otherwise noted Symbol Parameter Conditions Min. Typ. ICC-G Total Supply Current POUT = 17.5 dBm, 54 Mbps OFDM signal, 64QAM - 140 mA ICC-B Total Supply Current POUT = 20 dBm, 11 Mbps CCK signal, BT = 0.45 - 160 mA Quiescent Current No RF - 110 mA ICC_OFF Total Supply Current PEN = 0 V, No RF Applied, CBT = PEN =CRX= 0 V - IDD_OFF Total Supply Current PEN = 0 V, No RF Applied, CBT = PEN =CRX= 0 V - Icc_LNA LNA Supply Current LEN =3.3V - Icc_LNA_ LNA bypass supply current LEN=0 ICQ BYP Max. Unit 10 μA 18 30 μA 10 13 mA 50 μA Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202406A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 24, 2012 3 DATA SHEET SE2613T: 2.4 GHz Wireless LAN/BT Front-End Control Logic Characteristics Conditions: VCC = 3.6V, VDD=3.3V, TA = 25 °C, as measured on Skyworks Solutions’ SE2613T-EK1 evaluation board (de-embedded to device), all unused ports terminated with 50 ohms, unless otherwise noted. Symbol Parameter Conditions Min. Typ. Max. Unit VIH Logic High Voltage - 2.7 - 3.6 V VIL Logic Low Voltage - 0 - 0.4 V IIH Input Current Logic High Voltage PEN All others - IIL Input Current Logic Low Voltage - - 100 10 - 1 μA μA Control Logic Table Mode# Mode Description CBT CRX PEN LEN 0 All Off 0 0 0 0 1 TX 0 0 1 0 2 RX High gain 0 1 0 1 3 RX Low gain (Bypass) 0 1 0 0 4 BT 1 0 0 0 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202406A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 24, 2012 4 DATA SHEET SE2613T: 2.4 GHz Wireless LAN/BT Front-End AC Electrical Characteristics 802.11g Transmit Characteristics Conditions: VCC = 3.6V, PEN = VDD = 3.3 V, CBT = LEN = CRX = 0V, TA = 25 °C, as measured on Skyworks Solutions’ SE2613T-EK1 evaluation board (de-embedded to device), all unused ports terminated with 50 ohms, unless otherwise noted. Symbol FIN Parameter Frequency Range Condition Min. Typ. - 2412 - 2484 MHz - - 4 % - 2.5 % EVM POUT = 17.5dBm, 54 Mbps OFDM signal, 64 QAM EVMLP Low Power EVM POUT = 0-15dBm, 54 Mbps OFDM S21 Small Signal Gain - Small Signal Gain Variation Over Band - EVM ΔS21 2f Harmonics - Max. 26 - POUT = 20 dBm, 1 Mbps, 802.11b - - 3f Unit dB 1.5 dBpp -25 dBm/MHz -25 dBm/MHz 400 nsec -10 dB tdr, tdf Delay and rise/fall Time 50 % of VPEN edge and 90/10 % of final output power level - S11 Input Return Loss TX port - STAB Stability CW, Pin = -5 dBm 0.1 GHz – 20 GHz Load VSWR = 6:1 All non-harmonically related outputs less than -43 dBm/MHz RGGD Ruggedness CW, PIN = -5 dBm 0.1 GHz – 20 GHz Load VSWR = 10:1 No permanent damage or performance degradation -12 Bluetooth Characteristics Conditions: VCC = 3.6 V, CBT = VDD = 3.3V, CRX = LEN = PEN = 0V, TA = 25 °C, as measured on Skyworks Solutions’ SE2613T-EK1 evaluation board (de-embedded to device), all unused ports terminated with 50 ohms, unless otherwise noted. Symbol Parameter FOUT Frequency Range BTIL Insertion Loss S11 BT Port Return Loss ISOLSW Switch Isolation Condition Min. Typ. - 2400 - 2500 MHz - 0.5 0.8 dB -12 24 Max. Unit dB dB Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202406A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 24, 2012 5 DATA SHEET SE2613T: 2.4 GHz Wireless LAN/BT Front-End 2.4 GHz Receive Characteristics Conditions: VCC = 3.6 V, LEN = CRX = VDD = 3.3V, PEN = CBT = 0 V, TA = 25 °C, as measured on Skyworks Solutions’ SE2613T-EK1 evaluation board (de-embedded to device), all unused ports terminated with 50 ohms, unless otherwise noted. Symbol Parameter FOUT Frequency Range S21 Receive Gain, LNA enabled. ΔS21 Gain Variation Condition Min. Typ. - 2400 - 2500 MHz 11 13 15 dB - - 0.5 dB 2400 – 2485 MHz, Over any 20MHz band NF Noise Figure - 1.8 IIP3 Third Order Intercept 4 5 S11 Input Return Loss S22 Output Return Loss IP1dB - Input P1dB CW Enable Time 10% to 90% of RX RF power, from time that LEN is at 50% S21-BYP Receive Gain, LNA bypassed LEN = 0 V S11-BYP Input Return Loss, LNA bypassed LEN = 0 V TEN ISOLSW Switch Isolation -6 -5 Unit dB - dBm -10 dB -10 dB -5 dBm -3 -10 20 Max. 400 nsec -1 dB dB dB Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202406A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 24, 2012 6 DATA SHEET SE2613T: 2.4 GHz Wireless LAN/BT Front-End Power Detector Characteristics Conditions: VCC =3.6V, PEN = VDD = 3.3 V, CBT = LEN = CRX = 0V, TA = 25 °C, as measured on Skyworks Solutions’ SE2613T-EK1 evaluation board (de-embedded to device), unless otherwise noted. Symbol Parameter FOUT Frequency Range PDR Power detect range, CW Condition Min. Typ. - 2400 - 2500 MHz 0 - 22 dBm Measured at ANT Max. Unit - 2.2 KΩ Output Voltage, POUT = No RF Measured in to 1MΩ 0.2 V PDVp17.5 Output Voltage, POUT = 17.5 dBm CW Measured in to 1MΩ 0.8 V PDVVAR Detector variation over Voltage 3.2V to 3.9V Vcc constant detector voltage ([email protected] Vcc nominal) 0.5 PDZLOAD Output Impedance PDVNoRF PDBW Detector bandwidth 1 1 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202406A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 24, 2012 dBpp MHz 7 DATA SHEET SE2613T: 2.4 GHz Wireless LAN/BT Front-End Package Handling Information Branding Information The device branding is shown in Figure 3. 2613T Figure 3: SE2613T Branding and Pin 1 Location Package Diagram The package diagram is shown in Figure 4. 16 15 14 13 13 14 15 16 1 12 12 1 2 11 11 2 3 10 10 3 4 9 9 4 5 6 7 8 8 7 6 5 TOP SIDE BOTTOM SIDE Figure 4: SE2613T Package Diagram Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202406A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 24, 2012 8 DATA SHEET SE2613T: 2.4 GHz Wireless LAN/BT Front-End Recommended PCB Footprint and Solder pattern 16 15 14 13 1 12 2 11 3 10 4 9 16 14 7 5 6 7 8 5 16 15 14 13 16 15 14 13 1 12 1 12 2 11 2 11 3 10 3 10 4 9 4 9 5 6 7 5 8 6 7 8 Figure 5: PCB Footprint and Solder pattern Package Handling Information Because of its sensitivity to moisture absorption, instructions on the shipping container label must be followed regarding exposure to moisture after the container seal is broken, otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly. The SE2613T is capable of withstanding a Pb free solder reflow. Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. If the part is manually attached, precaution should be taken to insure that the device is not subjected to temperatures above its rated peak temperature for an extended period of time. For details on both attachment techniques, precautions, and handling procedures recommended, please refer to: “QFN solder reflow and rework information application note”, Document Number QAD-00045 “Handling, packing, shipping and use of moisture sensitive QFN application note”, Document Number QAD00044 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202406A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 24, 2012 9 DATA SHEET SE2613T: 2.4 GHz Wireless LAN/BT Front-End Tape and Reel Information Parameter Devices Per Reel Reel Diameter Tape Width Value 3000 13 inches 12 millimeters Figure 6: SE2613T-R Tape and Reel Information. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202406A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 24, 2012 10 DATA SHEET SE2613T: 2.4 GHz Wireless LAN/BT Front-End Document Change History Revision Date Notes 1.0 June-28-2010 Initial Release 1.1 October-01-2010 Updated package, pin out and technical specifications 1.2 October-11-2010 Updated Quiescent current 1.3 November-16-2010 Fixed typos. 1.4 March-28-2011 Updated specifications 1.5 April-11-2012 Updated with Skyworks logo and disclaimer statement Copyright © 2012 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks, the Skyworks symbol, and “Breakthrough Simplicity” are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202406A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 24, 2012 11