DATA SHEET SE5512L: Dual-Band 802.11a/b/g/n Wireless LAN Front-End Preliminary Information Applications Product Description The SE5512L is a complete 802.11a/b/g/n WLAN RF front-end module providing all the functionality of the power amplifiers, filtering, power detector, T/R switch, diplexers, LNA and associated matching. The SE5512L provides a complete 2.4 GHz and 5 GHz WLAN RF solution from the output of the transceiver to the antenna in an ultra compact form factor. IEEE802.11b DSSS WLAN IEEE802.11g OFDM WLAN IEEE802.11a OFDM WLAN IEEE802.11n WLAN Access Points, PCMCIA, PC cards Features All RF ports matched to 50 Ω Integrated 2.4 GHz PA, 5 GHz PA, T/R switch, 2.5GHz LNA, 5GHz LNA Integrated Power Detector for each TX Chain 19 dBm O/P Power, 802.11b, 11 Mbits, ACPR = 35 dBc 18 dBm @ 3.0 % EVM, 802.11g, 54 Mbits 16 dBm @ 3.0 % EVM, 802.11a, 54 Mbits Single supply voltage: 3.3 V ± 10 % Lead free, Halogen free, RoHS compliant, MSL 1 4mm x 4mm x 0.9mm, QFN Package Designed for ease of use, all RF ports are matched to 50 Ω to simplify PCB layout and the interface to the transceiver RFIC. The SE5512L also includes a transmit power detector with 20 dB of dynamic range for each transmit chain. Each transmit chain has a separate digital enable control for transmitter power ramp on/off control. The power ramp rise/fall time is less than 0.7 μsec. The device also provides a notch filter from 3.2603.267 GHz and 3.28-3.89 GHz prior to the input of each 2.4 GHz and 5 GHz power amplifiers, respectively. The SE5512L packaged in 4mm x 4mm x 0.9mm, Halogen free, Lead free, ROHS compliant, MSL 3 QFN package. Ordering Information Part No. Package Remark SE5512L SE5512L-R SE5512L-EK1 24 pin QFN 24 pin QFN N/A Samples Tape and Reel Evaluation kit Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202453A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 1 DATA SHEET SE5512L: Dual-Band 802.11a/b/g/n Wireless LAN Front-End Preliminary Information Functional Block Diagram f Figure 1: SE5512L Functional Block Diagram Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202453A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 2 DATA SHEET SE5512L: Dual-Band 802.11a/b/g/n Wireless LAN Front-End Preliminary Information Pin Out Diagram Figure 2: SE5512L Pin Out (Top View Through Package) Pin Out Description Pin No. Name 1 C0 2 Description Pin No. Name Description Switch Control 13 GND Ground Rg 2.4 GHz RF Receive Output 14 GND Ground 3 Ra 5 GHz RF Receive Output 15 GND Ground 4 Tg 2.4 GHz RF Transmit Input 16 GND Ground 5 Ta 5 GHz RF Transmit Input 17 ANT Antenna 6 Det 2.4/5 GHz Power Detector Output 18 GND Ground 7 ENa 5 GHz Power Amplifier Enable 19 GND Ground 8 ENg 2.4 GHz Power Amplifier Enable 20 GND Ground 9 VCC Supply Voltage 21 GND Ground 10 VCC Supply Voltage 22 GND Ground 11 VCC Supply Voltage 23 VCC Supply Voltage 12 VCC Supply Voltage 24 C1 Switch Control Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202453A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 3 DATA SHEET SE5512L: Dual-Band 802.11a/b/g/n Wireless LAN Front-End Preliminary Information Absolute Maximum Ratings These are stress ratings only. Exposure to stresses beyond these maximum ratings may cause permanent damage to, or affect the reliability of the device. Avoid operating the device outside the recommended operating conditions defined below. This device is ESD sensitive. Handling and assembly of this device should be at ESD protected workstations. Symbol Definition Min. Max. Unit VCC Supply Voltage -0.3 3.6 V PU ENa, ENg, C0, C1 -0.3 3.6 V - 12.0 dBm Operating Temperature Range -40 85 °C TSTG Storage Temperature Range -40 150 °C ESD HBM JEDEC JESD22-A114 all pins - 1,000 V TXRF TA Ta, Tg, ANT terminated in 6:1 load or better Recommended Operating Conditions Symbol Parameter Min. Typ. Max. Unit VCC Supply Voltage 3.0 3.3 3.6 V TA Ambient Temperature -40 25 85 °C DC Electrical Characteristics Conditions: VCC = 3.3 V, TA = 25 °C, as measured on Skyworks Solutions’ SE5512L-EV1 evaluation board (deembedded to device), all unused ports terminated with 50 ohms, unless otherwise noted Symbol Parameter ICC-G Total 802.11g Transmit Supply Current Conditions Min. Typ. Max. Unit POUT = 18 dBm, 54 Mbps OFDM signal, 64 QAM ENg = 3.3 V, ENa = 0 V, 100% duty cycle - 150 - mA ICC-B Total 802.11b Transmit Supply Current POUT = 19 dBm, 11 Mbps CCK signal, BT = 0.45, ENg = 3.3 V, ENa = 0 V, 100% duty cycle - 175 - mA ICC-A Total 802.11a Transmit Supply Current POUT = 16 dBm, 54 Mbps OFDM signal, 64 QAM, ENa = 3.3 V, ENg = 0 V, 100% duty cycle - 210 - mA Icc-Rxa Total Icc in Rx 5G band 5G LNA enabled - 19 - mA Icc-Rxg Total Icc in Rx 2G band 2G LNA enabled - 18 - mA ICC_OFF Total Supply Current No RF, ENg = ENa = 0 V - 50 180 μA Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202453A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 4 DATA SHEET SE5512L: Dual-Band 802.11a/b/g/n Wireless LAN Front-End Preliminary Information PA Logic Characteristics Conditions: VCC = 3.3 V, TA = 25 °C, as measured on Skyworks Solutions’ SE5512L-EV1 evaluation board (deembedded to device), all unused ports terminated with 50 ohms, unless otherwise noted. Symbol Parameter Conditions Min. Typ. Max. Unit VENH Logic High Voltage for ENg, ENa (Module On) - 1.8 - VCC V VENL Logic Low Voltage ENg, ENa (Module Off) - 0 - 0.4 V IENH Input Current Logic High Voltage (ENg, ENa) - - 50 100 μA IENL Input Current Logic Low Voltage (ENg, ENa) VCC = 0.4V - 0 40 μA Switch/LNA Logic Characteristics Conditions: VCC = 3.3 V, VEN = 0 V, TA = 25 °C, as measured on Skyworks Solutions’ SE5512L-EV1 evaluation board (de-embedded to device), all unused ports terminated with 50 ohms, unless otherwise noted. Symbol Parameter Conditions Min. Typ. Max. Unit VCTL_ON Control Voltage C0, C1 (On State) - 3.0 - 3.6 V VCTL_OFF Control Voltage C0, C1 (OFF State) - 0.0 - 0.4 V ICTL_ON Switch Control Bias Current (RF Applied) On pin (TX, RX) being driven high. RF Applied - - 400 µA ICTL_ON Switch Control Bias Current (No RF) On pin (TX, RX) being driven high. No RF - - 30 µA Switch & LNA Control Logic Table C0 C1 EnG EnA Tg ↔ ANT Ta ↔ ANT Rg ↔ ANT Ra ↔ ANT VCTL_OFF VCTL_ON VENH VENL ON OFF OFF OFF VCTL_OFF VCTL_OFF VENL VENH OFF ON OFF OFF VCTL_ON VCTL_OFF VENL VENL OFF OFF OFF LNA ON VCTL_ON VCTL_ON VENL VENL OFF OFF LNA ON OFF VCTL_OFF VCTL_OFF VENL VENL All Other States Stand By Mode, PAs and LNAs OFF – Low Current Consumption Not Supported Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202453A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 5 DATA SHEET SE5512L: Dual-Band 802.11a/b/g/n Wireless LAN Front-End Preliminary Information 2.4 GHz AC Electrical Characteristics 2.4 GHz Transmit Characteristics Conditions: VCC = 3.3 V, ENg = 3.3 V, ENa = C0 = C1 = 0 V, TA = 25 °C, as measured on Skyworks Solutions’ SE5512L-EV1 evaluation board, all unused ports terminated with 50 ohms, unless otherwise noted. Symbol FIN Parameter Frequency Range Condition Min. Typ. Max. Unit - 2400 - 2500 MHz P802.11g Output power 54 Mbps OFDM signal, 64QAM, EVM = 3.0 % - 18 - dBm P802.11b Output power 11 Mbps CCK signal, BT = 0.45 ACPR(± 11MHz offset) < -35 ACPR(± 22MHz offset) < -56 - 19 - dBm P1dB P1dB - 23 25.5 - dBm S21 Small Signal Gain - 25 28 30 dB Small Signal Gain Variation Over Band - - 1.0 2.0 dB ΔS21 S213.2 Gain at Ref-VCO 3200.00 to 3300.00 MHz - - 0 dB 2f,3f Harmonics Pout ≤ 19 dBm, 1Mbps, CCK - - -45.2 dBm/MHz tr Rise Time 10 % to 90% of final output power level - - 0.5 μs tdr, tdf Delay and rise/fall Time 50 % of VEN edge and 90/10 % of final output power level - - 0.5 μs S11 Input Return Loss 8 10 - dB STAB Ru - Stability CW, POUT = 19 dBm 0.1 GHz – 21 GHz Load VSWR = 6:1 Ruggedness Tg = 12dBm, ANT load varies over 6:1 VSWR All non-harmonically related outputs less than -42 dBm/MHz No Irreversible damage Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202453A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 6 DATA SHEET SE5512L: Dual-Band 802.11a/b/g/n Wireless LAN Front-End Preliminary Information 2.4 GHz Receive Characteristics Conditions: VCC = C0 = C1 = 3.3 V, ENg = ENa = 0 V, TA = 25 °C, as measured on Skyworks Solutions’ SE5512LEV1 evaluation board, all unused ports terminated with 50 ohms, unless otherwise noted. Symbol Parameter Condition Min. Typ. Max. Unit - 2400 - 2500 MHz 10 15 - dB FOUT Frequency Range S21 Receive Gain, LNA Enabled. 2400 – 2485 MHz Gain Variation 2400 – 2485 MHz, Over any 40MHz band - 0.2 0.5 dB NF Noise Figure De-embedded to device - 2.5 2.8 dB INT Interferer @1710-1990MHz With this input , IIP3 can only degrade by 1dB -10 - - dBm S11 Input Return Loss - 8 - dB ΔS21 IP1dB TEN - Input P1dB C0 = 3.3 V - -7 - dBm Enable Time 10% to 90% of RX RF power, from time that C0 is at 50% - 500 - nsec Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202453A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 7 DATA SHEET SE5512L: Dual-Band 802.11a/b/g/n Wireless LAN Front-End Preliminary Information 5 GHz AC Electrical Characteristics 5 GHz Transmit Characteristics Conditions: VCC = 3.3 V, ENa = 3.3 V, ENg = C0 = C1 = 0 V, TA = 25 °C, as measured on Skyworks Solutions’ SE5512L-EV1 evaluation board, all unused ports terminated with 50 ohms, unless otherwise noted. Symbol FIN P802.11a Parameter Frequency Range Nominal Output Power Condition Min. Typ. Max. Unit - 4900 - 5875 MHz 54 Mbps OFDM signal, 64 QAM, EVM = 3.0 % - 16 - dBm P1dB P1dB - 21 22.5 - dBm S21 Small Signal Gain - 24 - 32 dB Small Signal Gain Variation Over 40 MHz Channel - - 0.5 dB Small Signal Gain Variation Over subbands - - 3 dB ΔS21 S213.2 Gain 3280 to 3900 MHz - 3 9 dB 2f,3f Harmonics Pout ≤ 16 dBm typ, 54Mbps, 802.11a OFDM - - -45.2 dBm/MHz tr Rise Time 10 % to 90% of final output power level - - 0.5 μs tdr, tdf Delay and rise/fall Time 50 % of VEN edge and 90/10 % of final output power level - - 0.5 μs S11 Input Return Loss 5 7 - dB STAB Ru - Stability 64 QAM, POUT = 16 dBm 0.1 GHz – 21 GHz Load VSWR = 6:1 All non-harmonically related outputs less than -42 dBm/MHz Ruggedness TXa = 12dBm, ANT load varies over 6:1 VSWR No Irreversible damage Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202453A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 8 DATA SHEET SE5512L: Dual-Band 802.11a/b/g/n Wireless LAN Front-End Preliminary Information 5 GHz Receive Characteristics Conditions: VCC = C0 = 3.3 V, ENg = ENa = C1 = 0 V, TA = 25 °C, as measured on Skyworks Solutions’ SE5512LEV1 evaluation board, all unused ports terminated with 50 ohms, unless otherwise noted. Symbol Parameter Condition Min. Typ. Max. Unit - 4900 - 5850 MHz 10 12 - dB FOUT Frequency Range S21 Receive Gain 4900 – 5850 MHz ΔS21 Gain Variation 4900 – 5850 MHz, Over any 40MHz band - 1 - dB NF Noise Figure De-embedded to device - 2.8 3.0 dB S11 Return Loss 10 15 - dB IP1dB Input P1dB C0 = 3.3 V -6.5 - - dBm Enable Time 10% to 90% of RX RF power, from time that C0 is at 50% - 500 - nsec TEN - Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202453A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 9 DATA SHEET SE5512L: Dual-Band 802.11a/b/g/n Wireless LAN Front-End Preliminary Information 2.4 GHz Power Detector Characteristic Conditions: VCC = 3.3 V, ENg = 3.3 V, ENa = C0 = C1 = 0 V, TA = 25 °C, as measured on Skyworks Solutions’ SE5512L-EV1 evaluation board, all unused ports terminated with 50 ohms, unless otherwise noted. Symbol Parameter FOUT Frequency Range PDR Power detect range, peak power Condition Min. Typ. - 2400 - 2500 MHz 0 - 22 dBm Measured at ANT0 or ANT1 Max. Unit PDZOUT DC Output impedance - - 2.7 3 kΩ PDVP21 Output Voltage, POUT = 21dBm - - 0.85 - V PDVp18 Output Voltage, POUT = 18dBm - - 0.65 - V PDVpnoRF Output Voltage, POUT = No RF - - 0.35 - V LPF-3dB Power detect low pass filter -3dB corner frequency - 1500 - kHz Load = high impedance Typ: 500 kΩ 2.5GHz Pow er Detector Response into 1MΩ Load 2400 2450 2500 VDET (V) 1.1 0.9 0.7 0.5 0.3 3 5 7 9 11 13 15 17 Output Pow er (dBm ) 19 21 23 Figure 3: SE5512L Power Detector vs. Output Power over Frequency (CW Signal) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202453A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 10 DATA SHEET SE5512L: Dual-Band 802.11a/b/g/n Wireless LAN Front-End Preliminary Information 5 GHz Power Detector Characteristic Conditions: VCC = 3.3 V, ENa = 3.3 V, ENg = C0 = C1 = 0 V, TA = 25 °C, as measured on Skyworks Solutions’ SE5512L-EV1 evaluation board, all unused ports terminated with 50 ohms, unless otherwise noted. Symbol Parameter FOUT Frequency Range PDR Power detect range, peak power Condition Min. Typ. - 4900 - 5850 MHz 0 - 21 dBm Measured at ANT Max. Unit PDZOUT DC Output impedance - - 2.7 3.0 kΩ PDVp18 Output Voltage, POUT = 18dBm - - 0.78 - V PDVp16 Output Voltage, POUT = 16dBm - - 0.65 - V PDVNoRF Output Voltage, POUT = No RF - - 0.35 - V LPF-3dB Power detect low pass filter -3dB corner frequency - 1500 - kHz Load = high impedance Typ: 500 kΩ 5GHz Power Detector Response Pdet5090 Pdet4900 Pdet5470 Pdet5850 1 0.9 VDET (V) 0.8 0.7 0.6 0.5 0.4 0.3 0 2 4 6 8 10 12 14 16 18 20 Pout(dBm) Figure 4: Preliminary SE5512L Power Detector vs. Output Power over Frequency (CW Signal) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202453A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 11 DATA SHEET SE5512L: Dual-Band 802.11a/b/g/n Wireless LAN Front-End Preliminary Information Package Drawing 24 23 22 21 20 19 19 20 21 22 23 24 1 18 18 1 2 17 17 2 3 16 16 3 4 15 15 4 5 14 14 5 6 13 13 6 7 8 9 10 11 12 12 TOP SIDE 11 10 9 8 7 BOTTOM SIDE Figure 5: Package Drawing: Topside Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202453A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 12 DATA SHEET SE5512L: Dual-Band 802.11a/b/g/n Wireless LAN Front-End Preliminary Information Recommended Land and Solder Patterns 24 23 22 21 20 24 19 23 22 21 20 19 24 23 22 21 20 19 1 18 1 18 1 18 2 17 2 17 2 17 3 16 3 16 3 16 4 15 4 15 4 15 5 14 5 14 5 14 6 13 6 13 6 13 7 8 9 10 11 12 7 8 9 10 11 12 7 8 9 10 11 12 Figure 6: Recommended Land and Solder Patterns Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202453A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 13 DATA SHEET SE5512L: Dual-Band 802.11a/b/g/n Wireless LAN Front-End Preliminary Information Package Handling Information Because of its sensitivity to moisture absorption, instructions on the shipping container label must be followed regarding exposure to moisture after the container seal is broken, otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly. The SE5512L is capable of withstanding a Pb free solder reflow. Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. If the part is manually attached, precaution should be taken to insure that the device is not subjected to temperatures above its rated peak temperature for an extended period of time. For details on both attachment techniques, precautions, and handling procedures recommended, please refer to: “Quad Flat No-Lead Module Solder Reflow & Rework Information”, Document Number QAD-00045 “Handling, Packing, Shipping and Use of Moisture Sensitive QFN”, Document Number QAD-00044 Caution! Class 1C ESD sensitive device Product Branding Pin 1 Identifier Terminal Finish Pin 1 e3 Part Lot SiGe 5512L Lot Code Figure 7: SE5512L Branding Information Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202453A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 14 DATA SHEET SE5512L: Dual-Band 802.11a/b/g/n Wireless LAN Front-End Preliminary Information Tape and Reel Information Parameter Devices Per Reel Reel Diameter Tape Width Value 3000 13 inches 12 millimeters Figure 8: Detailed Tape and Reel Information (All diminensions in Millimeters) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202453A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 15 DATA SHEET SE5512L: Dual-Band 802.11a/b/g/n Wireless LAN Front-End Preliminary Information Document Change History Revision 1.0 Date Notes Aug 10, 2010 Create 1.1 Sep 30, 2010 Updated 2GHz LNA gain variation over a single channel. Updated EN (high) current limit Updated 5GHz Gain (min) limit. 1.2 Oct 7, 2010 Added “Stand By” mode setting to switch control logic table 1.3 Jan 27, 2011 Updated MSL rating to MSL1 Updated ESD rating to Class 1C 1.4 Sep 25, 2011 Updated recommended operating conditions to Industrial level 1.5 Feb 17, 2012 Updated marking diagram 1.6 Apr 03, 2012 Updated with Skyworks logo and disclaimer statement Copyright © 2012 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks, the Skyworks symbol, and “Breakthrough Simplicity” are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202453A • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • September 25, 2012 16