DATA SHEET SKY12213-478LF: 0.5 to 6.0 GHz, 150 W High Power Silicon PIN Diode SPST Switch Applications Failsafe switching in TD-SCDMA, WiMAX, and LTE TDD base stations On/off switching in land mobile radios and military communications systems High power series diodes IN_1 OUT_1 IN_2 OUT_2 S3109 Features Figure 1. SKY12213-478LF Block Diagram High power handling: 150 W CW Low insertion loss: 0.5 to 1.0 dB typical High isolation: 23 dB typical Controlled with positive power supply Description Small, QFN (16-pin, 4 x 4 mm) Pb-free package (MSL1, 260 C per JEDEC J-STD-020) N/C N/C N/C N/C Skyworks Green™ products are compliant with all applicable legislation and are halogen-free. For additional information, refer to Skyworks Definition of Green™, document number SQ04-0074. 16 15 14 13 IN_1 2 11 OUT_1 IN_2 3 10 OUT_2 GND 4 9 GND 5 6 7 8 N/C GND N/C 12 N/C 1 N/C GND The SKY12213-478LF is a high power handling, Single-Pole, Single-Throw (SPST) silicon PIN diode switch. The device operates over the 0.5 GHz to 6.0 GHz band. It features low insertion loss, excellent power handling, and superb linearity with low DC power consumption. The SKY12213-478LF is well-suited for use as a high power SPST switch in a variety of telecommunication systems such as WiMAX, TD-SCDMA, or LTE base stations. It can also be used as a high power series diode in a multitude of PIN diode applications. The device is provided in a 4 x 4 mm, 16-pin Quad Flat No-Lead (QFN) package. A functional block diagram is shown in Figure 1. The pin configuration and package are shown in Figure 2. Signal pin assignments and functional pin descriptions are provided in Table 1. S3105 Figure 2. SKY12213-478LF Pinout – 16-Pin QFN (Top View) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202180D • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • January 27, 2014 1 DATA SHEET • SKY12213-478LF HIGH POWER PIN DIODE SPST SWITCH Table 1. SKY12213-478LF Signal Descriptions Pin Name Description Pin Name Description 1 GND Ground. Must be connected to ground using lowest possible impedance. 9 GND Ground. Must be connected to ground using lowest possible impedance. 2 IN_1 Input RF port 1 and DC bias input port. 10 OUT_2 Output RF port 2 and DC bias input port. 3 IN_2 Input RF port 2 and DC bias input port. 11 OUT_1 Output RF port 1 and DC bias input port. 4 GND Ground. Must be connected to ground using lowest possible impedance. 12 GND Ground. Must be connected to ground using lowest possible impedance. 5 N/C No connection 13 N/C No connection 6 N/C No connection 14 N/C No connection 7 N/C No connection 15 N/C No connection 8 N/C No connection 16 N/C No connection Table 2. SKY12213-478LF Absolute Maximum Ratings Parameter Symbol Minimum Maximum Units RF CW input power @ input ports (TSUBSTRATE = 25 °C) PIN 190 W RF peak input power @ input ports (TSUBSTRATE = 25 °C, RF burst width = 10 μs, RF burst repetition rate = 25 kHz) PIN 760 W Control port reverse voltage VCTL 200 V Control port forward current ICTL 200 mA Operating temperature TOP –55 +175 C Storage temperature TSTG –55 +200 C Electrostatic discharge: ESD 1000 2000 200 V V V Charged Device Model (CDM), Class 4 Human Body Model (HBM), Class 2 Machine Model (MM), Class B Note: Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other parameters set at or below their nominal value. Exceeding any of the limits listed here may result in permanent damage to the device. CAUTION: Although this device is designed to be as robust as possible, Electrostatic Discharge (ESD) can damage this device. This device must be protected at all times from ESD. Static charges may easily produce potentials of several kilovolts on the human body or equipment, which can discharge without detection. Industry-standard ESD precautions should be used at all times. Table 3. Recommended Operating Conditions Parameter Min Typical Max Units VCTL 0 +28 +100 V Control port reverse voltage VCTL –100 –28 0 V Control port forward current ICTL 50 100 100 mA Control port forward voltage Symbol Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 2 January 27, 2014 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202180D DATA SHEET • SKY12213-478LF HIGH POWER PIN DIODE SPST SWITCH Electrical and Mechanical Specifications Typical performance characteristics of the SKY12213-478LF are illustrated in Figures 3 through 6. The absolute maximum ratings of the SKY12213-478LF are provided in Table 2. Recommended operating conditions are specified in Table 3. Electrical specifications are provided in Table 4. Power derating data is plotted against temperature in Figures 7 and 8. “On/off” switch state circuit diagrams are shown in Figure 9. The state of the SKY12213-478LF is determined by the logic provided in Table 5. Table 6 provides the logic for use with the SKY12213-478LF Evaluation Board. Table 4. SKY12213-478LF Electrical Specifications, Bias Voltage = 28 V (1 of 2) (Note 1) (TOP = +25 C, Characteristic Impedance [ZO] = 50 Ω, EVB Optimized for 2.6 GHz Operation, Unless Otherwise Noted) Parameter Insertion loss, IN_1/2 to OUT_1/2 ports Symbol IL Test Condition Min Iso Max Units 1.40 dB dB dB dB dB Pins 2 & 3 = +28 V @ 100 mA, pins 10 & 11 = 0 V, PIN @ IN_1/2 ports = 0 dBm: 1.30 0.27 1.10 0.54 1.30 0.5 GHz 1.0 GHz 2.6 GHz 3.5 GHz 6.0 GHz Isolation, IN_1/2 to OUT_1/2 ports Typical Pins 2 & 3 = 0 V @ 0 mA, pins 10 & 11 = 0 V, PIN @ IN_1/2 ports = 0 dBm: 0.5 GHz 1.0 GHz 2.6 GHz 3.5 GHz 6.0 GHz 20 34 26 24 24 20 dB dB dB dB dB Input return loss |S11| Pins 2 & 3 = +28 V @ 100 mA, pins 10 & 11 = 0 V, IN_1/2 ports insertion loss state, 0.5 to 6.0 GHz 15 dB Output return loss |S22| Pins 2 & 3 = +28 V @ 100 mA, pins 10 & 11 = 0 V, OUT_1/2 ports insertion loss state, 0.5 to 6.0 GHz 15 dB 2nd harmonic 2fo Pins 2 & 3 = +28 V @ 100 mA, pins 10 & 11 = 0 V, IN_1/2 ports insertion loss state, PIN = +30 dBm: –101 –98 –108 –112 –95 dBc dBc dBc dBc dBc 0.5 GHz 1.0 GHz 2.6 GHz 3.5 GHz 6.0 GHz Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202180D • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • January 27, 2014 3 DATA SHEET • SKY12213-478LF HIGH POWER PIN DIODE SPST SWITCH Table 4. SKY12213-478LF Electrical Specifications, Bias Voltage = 28 V (2 of 2) (Note 1) (TOP = +25 C, Characteristic Impedance [ZO] = 50 Ω, EVB Optimized for 2.6 GHz Operation, Unless Otherwise Noted) Parameter rd 3 harmonic Symbol 3fo Test Condition Min Typical Max Units Pins 2 & 3 = +28 V @ 100 mA, pins 10 & 11 = 0 V, IN_1/2 ports insertion loss state, PIN = +30 dBm: 0.5 GHz 1.0 GHz 2.6 GHz 3.5 GHz 6.0 GHz –102 –108 –111 –115 –93 dBc dBc dBc dBc dBc 3rd Order Input Intercept Point IIP3 Pins 2 & 3 = +28 V @ 100 mA, pins 10 & 11 = 0 V, PIN @ IN_1/2 ports = +30 dBm/tone, tone spacing = 1 MHz, 2.6 GHz +72 dBm 0.1 dB Input Compression Point IP0.1dB Pins 2 & 3 = +28 V @ 100 mA, pins 10 & 11 = 0 V, 2.6 GHz +47 dBm Maximum CW input power PIN_CW Pins 2 & 3 = +28 V @ 100 mA, pins 10 & 11 = 0 V, 2.6 GHz 150 W RF switching time tSW Pins 2 & 3 = +28 V @ 100 mA, pins 10 & 11 = 0 V, 10% to 90% RF rise time, repetition rate = 25 kHz 190 ns Note 1: Performance is guaranteed only under the conditions listed in this Table. Table 5. SKY12213-478LF Truth Table Path Switch State (See Figure 9) Control Conditions IN_1/2 to OUT_1/2 (pins 2,3 to pins 10, 11) Input Port Bias (Pins 2, 3) (V) Output Port Bias (Pins 10, 11) (mA) On Low insertion loss +28 –100 Off High isolation –28 0 Table 6. SKY12213-478LF Evaluation Board Truth Table Path Control Conditions Switch State (See Figure 9) RFIN to RFOUT Bias 1 Port (V) Bias 2 Port On Low insertion loss +28 ground Off High isolation –28 ground Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 4 January 27, 2014 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202180D DATA SHEET • SKY12213-478LF HIGH POWER PIN DIODE SPST SWITCH Typical Performance Characteristics (TOP = +25 C, Characteristic Impedance [ZO] = 50 Ω, EVB Optimized for 2.6 GHz Operation, Bias = 28 V/100 mA, Unless Otherwise Noted) 0 S11 S22 –5 0 –10 –0.5 –15 Return Loss (dB) Insertion Loss (dB) –1.0 –1.5 –2.0 –2.5 –3.0 –20 –25 –30 –35 –3.5 –40 –4.0 –45 –4.5 –5.0 –50 0 1 2 3 4 5 6 0 1 2 0 5 6 0 –5 0.9 GHz 2.0 GHz 2.6 GHz 3.5 GHz –0.2 –10 –0.4 Insertion Loss (dB) –15 Isolation (dB) 4 Figure 4. Return Loss vs Frequency Figure 3. Insertion Loss vs Frequency –20 –25 –30 –35 –40 –0.6 –0.8 –1.0 –1.2 –1.4 –1.6 –45 –50 3 Frequency (GHz) Frequency (GHz) –1.8 0 1 2 3 4 Frequency (GHz) Figure 5. Isolation vs Frequency 5 6 –2.0 0 20 14 60 80 100 120 140 160 Input Power (W) Figure 6. Insertion Loss vs CW Input Power Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202180D • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • January 27, 2014 5 DATA SHEET • SKY12213-478LF HIGH POWER PIN DIODE SPST SWITCH Maximum CW Incident Power (W) 160 140 120 100 80 60 40 20 0 25 35 45 55 65 75 85 95 105 115 125 135 145 155 165 175 OUT_1/2 IN_1/2 Temperature on Bottom of Package Ground Plane (°C) Figure 7. Power Derating, Maximum CW Incident Power (Insertion Loss = 0.4 dB) vs Ground Plane Temperature On State Forward Bias Maximum CW Incident Power (W) 160 OUT_1/2 IN_1/2 140 120 100 Off State Reversed Bias 80 S3106 60 40 Figure 9. SKY12213-478LF Equivalent Circuit Diagrams 20 0 25 35 45 55 65 75 85 95 105 115 125 135 145 155 165 175 Temperature on Bottom of Printed Circuit Board (°C) Figure 8. Power Derating, Maximum CW Incident Power (Insertion Loss = 0.4 dB) vs Circuit Board Temperature Evaluation Board Description The SKY12213-478LF Evaluation Board is used to test the performance of the SKY12213-478LF PIN Diode SPST switch. An assembly drawing for the Evaluation Board is shown in Figure 10. The layer detail is provided in Figure 11. The SKY12213-478LF is designed to handle very large signals. Sufficient power may be dissipated by this switch to cause heating of the PIN diode contained in the switch. It is very important to use a printed circuit board design that provides adequate cooling capability to keep the junction temperature of the PIN diode below its maximum rated operating temperature. As indicated in Figure 7, the x-axis temperature is referenced to the bottom of the QFN package. A printed circuit board with a very low thermal resistance and external heat sink design must be used to achieve the results shown in this Figure. The power derating curve with the x-axis temperature referenced to the bottom of the printed circuit board is provided in Figure 8. Due to the very high power level requirements on the SKY12213478LF and the input DC blocking capacitors, antenna port connections are combined outside the package on the Evaluation Board. The schematic diagram shown in Figure 12 indicates how these connections are made. The evaluation circuit is designed to facilitate control of the SKY12213-478LF. The state of the PIN diode within the SKY12213-478LF is controlled with +28 V applied to the Bias 1 (input) port; the Bias 2 (output) port is connected to DC ground. The switch state circuit diagrams are shown in Figure 9. The values of resistors R3 and R4 (refer to the schematic diagram in Figure 12), which are both nominally 280 Ω, determine how much current flows through the forward biased diode. For example, to place the SKY12213-478LF into the “on” state, +28 V is applied to the Bias 1 port, which forward biases the diode between pins 2 and 3, and pins 10 and 11. The values of R3 and R4 may be adjusted to accommodate other bias voltages. A resistance value of 280 Ω is selected to produce approximately 100 mA of forward bias current in the diodes, which are forced into conduction when the bias source voltage is +28 V. The component values shown in the Evaluation Board schematic (Figure 12) were selected to optimize performance over the 0.5 to 6.0 GHz band. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 6 January 27, 2014 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202180D DATA SHEET • SKY12213-478LF HIGH POWER PIN DIODE SPST SWITCH Package and Handling Information Refer to Table 7 for the Evaluation Board Bill of Materials. Table 8 provides voltage, current, and resistor values for bias adjustments. Package Dimensions Instructions on the shipping container label regarding exposure to moisture after the container seal is broken must be followed. Otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly. The PCB layout footprint for the SKY12213-478LF is shown in Figure 13. Typical case markings are noted in Figure 14. Package dimensions for the 16-pin QFN are shown in Figure 15, and tape and reel dimensions are provided in Figure 16. The SKY12213-478LF is rated to Moisture Sensitivity Level 1 (MSL1) at 260 C. It can be used for lead or lead-free soldering. For additional information, refer to the Skyworks Application Note, Solder Reflow Information, document number 200164. 1 2 3 GND BIAS_OUT1 BIAS_IN1 GND Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. Production quantities of this product are shipped in a standard tape and reel format. 4 5 6 RFIN RFOUT S3107 Figure 10. SKY12213-478LF Evaluation Board Assembly Diagram Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202180D • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • January 27, 2014 7 DATA SHEET • SKY12213-478LF HIGH POWER PIN DIODE SPST SWITCH Cross Section Name Thickness (in) Material Top Soldermask L1 (0.0028) Cu foil 0.012 ± 0.0006 Rogers RO4003C Core L2 (0.0014) Cu foil Laminate (Note 1) FR4 Prepreg L3 (0.0014) Cu foil 0.010 ± 0.0006 FR4 Core (0.0028) Cu foil Laminate Laminate L4 Bottom Soldermask Note 1: Adjust this thickness to meet total thickness goal of 0.062 ± 0.005 inches. S2531 Figure 11. Layer Detail Physical Characteristics Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 8 January 27, 2014 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202180D DATA SHEET • SKY12213-478LF HIGH POWER PIN DIODE SPST SWITCH N/C C5 15 14 × R3, R4 C6 L2 L1 12 1 C1 2 RFIN GND GND IN_1 OUT_1 C3 RFOUT GND 5 6 × 7 9 N/C GND N/C OUT_2 N/C IN_2 N/C 4 11 10 3 C2 Bias 2 Port Ground 13 N/C 16 × N/C Bias 1 Port +28 V × N/C × R1 8 × × × NOTE: The N/C pins (5 to 8 and 13 to 16) are not internally connected, so they can be left open or grounded. S3108 Figure 12. Evaluation Board Schematic Table 8. Evaluation Board Bill of Materials (Note 1) Component Value Size Manufacturer Mfr Part Number Characteristics C1, C2, C3, C5, C6 1000 pF 0603 TDK C1608C0G1H102JT COG, 50 V, ±5% C4 DNI – – – – L1, L2 22 nH 0603 Taiyo-Yuden HK160822NJ-T SRF 1600 MHz, ±5% R1 0Ω 2512 Vishay Dale CRCW25120000Z0EG 500 V, 1 W R2, R5, R6 DNI – – – – R3, R4 (Note 2) 560 Ω 2512 Multicomp MCPWR12FTEA5600 Total value = 280 Ω, 500 V, 1.5 W, ±1% Note 1: Component values selected are based on the desired frequency and bias level. Values may be adjusted for a specific response. Note 2: Evaluation Board includes a 280 Ω resistor for 28 V, 100 mA operation. Operating at 28 V and 100 mA requires a resistor with a power dissipation greater than 2.8 W. Table 9. Component Calculation Values VS (V) VDIODE (V) VRES (V) Current (A) Target Resistance (Ω) Power Dissipation (W) 28 2 26 0.05 520 1.3 28 2 26 0.10 260 2.6 Notes: Vs = supply voltage; VDIODE = voltage drop across the diode; VRES = voltage drop across the resistor. Resistor values are calculated by (Vs – VDIODE)/I, where I is the desired bias current. The approximate voltage drop across the diode is 2 V. The resistor power dissipation is calculated by I x (VS – VDIODE). The resistor selected must be rated to sufficiently handle power greater than the dissipated power. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202180D • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • January 27, 2014 9 DATA SHEET • SKY12213-478LF HIGH POWER PIN DIODE SPST SWITCH 16X 1.45 (To Metal Pads) 0.508 Pitch 0.65 0.762 Typ. 0.325 9X Plated Thru Vias See Detail A Metal GND Pad (Sq.) 2.15 0.30 Exposed Soldering Area 0.75 Detail A S2274 All measurements in millimeters Figure 13. SKY12213-478LF PCB Layout Footprint Pin 1 Indicator Skyworks P/N Lot # Date Code YY = Calendar Year WW Week CC = Country Code Figure 14. Typical Case Markings Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 10 January 27, 2014 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202180D DATA SHEET • SKY12213-478LF HIGH POWER PIN DIODE SPST SWITCH C 4 B Pin 1 Indicator 2.15 +0.10/–0.15 (0.2) Seating Plane (1.075) 0.02 +0.03/–0.02 Pin 1 Indicator (Option B) Exposed Pad Pin 1 Indicator (Option A) 4 (1.075) 0.20 Min. 16X 2.15 +0.10/–0.15 A 0.15 C 2X 2X Detail B Detail A 0.15 C 1.50 ± 0.10 4 0.10 C 0.08 C 16X Side View Top View Bottom View R0.12 Typ. 0.18 R0.20 Pin 1 Indicator 0.55 ± 0.10 0.18 0.345 (0.325) 0.30 +0.05 0.10 M C A B 0.65 0.345 Detail A Detail B Option A Option B Scale: 40X 16 Places Scale: 20X Even Terminal Side Pin 1 Indicator Scale: 10X Pin 1 Indicator Scale: 20X All measurements are in millimeters. Dimensioning and tolerancing according to ASME Y14.5M-1994. Coplanarity applies to the exposed heat sink slug as well as the terminals. Package may have option A or option B pin 1 indicator. S2400a Figure 15. SKY12213-478LF 16-Pin QFN Package Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202180D • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • January 27, 2014 11 DATA SHEET • SKY12213-478LF HIGH POWER PIN DIODE SPST SWITCH 8.00 0.30 ± 0.05 Ø1.50 +0.1/–0.0 Ø1.50 Min. 0.25 R A R 0.30 Max 1.75 ± 0.10 5.50 ± 0.05 (See Note 3) 4.35 1.80 A A (R0.25) 4.35 0.25 12.0 ± 0.30 2.00 ± 0.05 (See Note 3) 4.00 (See Note 1) Pin 1 Indicator Notes: 1. Sprocket hole pitch cumulative tolerance: ±0.2 mm 2. Carrier tape: black conductive polystyrene. 3. Pocket position relative to sprocket hole, measure as true position of pocket, not pocket hole. 4. Cover tape material: transparent conductive adhesive. 5. ESD surface resistivity must meet all ESD requirements of Skyworks, specified in GP01-D232. 6. All dimensions are in millimeters. Figure 16. SKY12213-478LF Tape and Reel Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 12 January 27, 2014 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202180D S2817 DATA SHEET • SKY12213-478LF HIGH POWER PIN DIODE SPST SWITCH Ordering Information Model Name SKY12213-478LF PIN Diode SPST Switch Manufacturing Part Number SKY12213-478LF Evaluation Board Part Number SKY12213-478LF-EVB Copyright © 2012-2014 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks, the Skyworks symbol, and “Breakthrough Simplicity” are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 202180D • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • January 27, 2014 13