DATA SHEET SKY13473-12-569LF: 0.4 to 2.7 GHz SP10T LTE Transmit/Receive Switch with MIPI RFFE Interface Applications 3G/4G multimode cellular tablets and handsets (LTE, UMTS, CDMA2000) Embedded data cards applied to the decoder, the antenna pin is connected to one of 10 switched RF ports using a low insertion loss path, while the paths between the antenna pin and the other RF pins are in a high isolation state. No external DC blocking capacitors are required on the RF paths. Features Broadband frequency range: 0.4 to 2.7 GHz Low insertion loss High isolation and linearity Integrated, programmable MIPI interface TRX1 TRX2 TRX3 Default USID = 1010 Ten linear TRX ports with isolation greater than 20 dB @ 2.7 GHz Small QFN (20-pin, 2.4 x 2.4 x 0.75 mm) package (MSL1, 260 C per JEDEC J-STD–020) Skyworks Green™ products are compliant with all applicable legislation and are halogen-free. For additional information, refer to Skyworks Definition of Green™, document number SQ04-0074. TRX4 TRX5 ANT TRX6 TRX7 TRX8 TRX9 TRX10 SKY13473-569LF SP10T Antenna Switch with default USID = 1011 (Data Sheet #202148) SKY13473-12-569LF SP10T Antenna Switch with default USID = 1010 (this Data Sheet) Using advanced switching technologies, the SKY13473-12-569LF maintains low insertion loss and high isolation for both transmit and receive switching paths. The high linearity performance and low insertion loss achieved by the SKY13473-12-569LF makes it an ideal choice for UMTS, CDMA2000, and LTE applications. VIO SDATA The SKY13473-12-569LF is a Single Pole, Ten Throw (SP10T) antenna switch with a Mobile Industry Processor Interface (MIPI) and is part of a two-switch family: SCLK Description VDD Decoder S3083 Figure 1. SKY13473-12-569LF Block Diagram The SKY13473-12-569LF is manufactured in a compact, 2.4 x 2.4 x 0.75 mm, 20-pin surface mount Quad Flat No-Lead (QFN) package. A functional block diagram is shown in Figure 1. The pin configuration and package are shown in Figure 2. Signal pin assignments and functional pin descriptions are provided in Table 1. The switch also exhibits an excellent triple beat ratio and 2nd/3rd order Intermodulation Distortion (IMD) performance. Switching is controlled by an integrated MIPI interface. Depending on the logic Skyworks Solutions, Inc. • Phone [781] 376–3000 • Fax [781] 376–3100 • [email protected] • www.skyworksinc.com 202983B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 17, 2013 1 SDATA VIO VDD 19 18 17 16 GND 2 15 TRX1 TRX9 3 14 TRX2 TRX8 4 13 TRX3 TRX7 5 12 TRX4 TRX6 6 11 TRX5 8 9 10 GND 7 ANT TRX10 20 GND 1 GND N/C SCLK DATA SHEET • SKY13473-12–569LF SP10T LTE TRANSMIT/RECEIVE SWITCH WITH MIPI RFFE INTERFACE S3082 Figure 2. SKY13473-12-569LF Pinout – 20-Pin QFN (Top View) Table 1. SKY13473-12-569LF Signal Descriptions Pin # Name Description Pin # Name Description 1 N/C No connection. Can be grounded or left floating. 11 TRX5 Multi-band, multi-mode transmit/receive port #5. This pin is either connected directly to or is disconnected from pin 9, depending on the control data applied to pin 19. 2 TRX10 Multi-band, multi-mode transmit/receive port #10. This pin is either connected directly to or is disconnected from pin 9, depending on the control data applied to pin 19. 12 TRX4 Multi-band, multi-mode transmit/receive port #4. This pin is either connected directly to or is disconnected from pin 9, depending on the control data applied to pin 19. 3 TRX9 Multi-band, multi-mode transmit/receive port #9. This pin is either connected directly to or is disconnected from pin 9, depending on the control data applied to pin 19. 13 TRX3 Multi-band, multi-mode transmit/receive port #3. This pin is either connected directly to or is disconnected from pin 9, depending on the control data applied to pin 19. 4 TRX8 Multi-band, multi-mode transmit/receive port #8. This pin is either connected directly to or is disconnected from pin 9, depending on the control data applied to pin 19. 14 TRX2 Multi-band, multi-mode transmit/receive port #2. This pin is either connected directly to or is disconnected from pin 9, depending on the control data applied to pin 19. 5 TRX7 Multi-band, multi-mode transmit/receive port #7. This pin is either connected directly to or is disconnected from pin 9, depending on the control data applied to pin 19. 15 TRX1 Multi-band, multi-mode transmit/receive port #1. This pin is either connected directly to or is disconnected from pin 9, depending on the control data applied to pin 19. 6 TRX6 Multi-band, multi-mode transmit/receive port #6. This pin is either connected directly to or is disconnected from pin 9, depending on the control data applied to pin 19. 16 GND Ground 7 GND Ground 17 VDD DC power supply 8 GND Ground 18 VIO MIPI decoder Interface/reference voltage 9 ANT Antenna input/output 19 SDATA Data input/output 10 GND Ground 20 SCLK Clock signal Skyworks Solutions, Inc. • Phone [781] 376–3000 • Fax [781] 376–3100 • [email protected] • www.skyworksinc.com 2 December 17, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202983B DATA SHEET • SKY13473-12–569LF SP10T LTE TRANSMIT/RECEIVE SWITCH WITH MIPI RFFE INTERFACE Table 2. SKY13473-12-569LF Absolute Maximum Ratings Parameter Symbol Minimum Maximum Units 2.5 5.0 V Power supply VDD Digital control signal VIO 2 V RF input power PIN +33 dBm Storage temperature TSTG –55 +150 C Operating temperature TOP –40 +90 C Note: Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other parameters set at or below their nominal value. Exceeding any of the limits listed here may result in permanent damage to the device. CAUTION: Although this device is designed to be as robust as possible, Electrostatic Discharge (ESD) can damage this device. This device must be protected at all times from ESD. Static charges may easily produce potentials of several kilovolts on the human body or equipment, which can discharge without detection. Industry-standard ESD precautions should be used at all times. Electrical and Mechanical Specifications The absolute maximum ratings of the SKY13473-12-569LF are provided in Table 2. Electrical specifications are provided in Tables 3 through 6. Figure 3 provides the timing diagram for turnon time and switching time. IMD2 and IMD3 test conditions for various frequencies are listed in Tables 7 and 8, respectively. Triple Beat Ratio (TBR) test conditions for bands 2 and 5 are listed in Table 9. Figure 4 illustrates the test setup used to measure intermodulation products. This industry standardized test is used to simulate the WCDMA Band 1 linearity of the antenna switch. A +20 dBm Continuous Wave (CW) signal, fFUND, is sequentially applied to the TRX1 through TRX10 ports, while a –15 dBm CW blocker signal, fBLK, is applied to the ANT port. The resulting 3rd Order Intermodulation Distortion (IMD3), fRX, is measured over all phases of fFUND. The SKY13473-12-569LF exhibits exceptional performance for all TRXx ports. Table 10 describes the register content and programming read/write sequences. Refer to the MIPI Alliance Specification for RF Front-End Control Interface (RFFE), v1.10 (26 July 2011) for additional information on MIPI programming sequences and MIPI bus specifications. Figures 5 and 6 provide the timing diagrams for register write commands and read commands, respectively. Table 11 provides the Register_0 logic. Table 12 describes the register parameters and bit values. Skyworks Solutions, Inc. • Phone [781] 376–3000 • Fax [781] 376–3100 • [email protected] • www.skyworksinc.com 202983B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 17, 2013 3 DATA SHEET • SKY13473-12–569LF SP10T LTE TRANSMIT/RECEIVE SWITCH WITH MIPI RFFE INTERFACE Table 3. SKY13473-12-569LF General Electrical Specifications (Note 1) (VDD = 2.85 V, VIO = 1.8 V, TOP = +25 C, Characteristic Impedance [ZO] = 50 Ω, Unless Otherwise Noted) Parameter Symbol Test Condition Min Typical Max 2.50 Supply voltage VDD 2.85 4.80 V Supply current, active mode IDD 35 80 μA Supply current, low power mode IDD 10 Interface supply VIO 1.65 Interface signal: High Low 1.80 μA 1.95 V 0.2 x VIO V V 10 5 μA μA 0.8 x VIO Control current: High Low ICTL Turn-on time (Note 2) tON Measured from 50% of final VDD supply voltage to 90% of RF power 20 Switching time (Note 2) tSW Measured from the rising edge of last clock signal to 90% RF power 2 μs 5 Note 1: Performance is guaranteed only under the conditions listed in this Table. Note 2: PIN = +27 dBm, TA = –40 to +90 °C. See Figure 3. Skyworks Solutions, Inc. • Phone [781] 376–3000 • Fax [781] 376–3100 • [email protected] • www.skyworksinc.com 4 Units December 17, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202983B μs DATA SHEET • SKY13473-12–569LF SP10T LTE TRANSMIT/RECEIVE SWITCH WITH MIPI RFFE INTERFACE VDD (V) VDD Final VDD 50% of final VDD Rising edge of last clock signal that sets the switch into the desired state VIO VIO (V) – Interface Supply SCLK (V) – Interface Signal SCLK Time (μs) POUT (dBm) POUT 90% of POUT Time (μs) Switching Time tsw < 5 μs Switching Time (tSW) is measured from the rising edge of the last clock signal to 90% of RF power. Turn-on Time (tON) is measured from 50% of final VDD supply voltage to 90% of RF power. Turn-on Time tON ~ 20 μs Y0113 Figure 3. SKY13473-12-569LF Timing Diagram Skyworks Solutions, Inc. • Phone [781] 376–3000 • Fax [781] 376–3100 • [email protected] • www.skyworksinc.com 202983B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 17, 2013 5 DATA SHEET • SKY13473-12–569LF SP10T LTE TRANSMIT/RECEIVE SWITCH WITH MIPI RFFE INTERFACE Table 4. SKY13473-12-569LF RF Electrical Specifications (1 of 2) (Note 1) (VDD = 2.85 V, TOP = +25 C, Characteristic Impedance [ZO] = 50 Ω, Unless Otherwise Noted) Parameter Symbol Test Condition Min Typical Max Units 2.7 GHz 0.45 0.60 0.80 0.65 0.80 0.95 dB dB dB Operating frequency f Insertion loss IL Up to 1.0 GHz Up to 2.0 GHz Up to 2.7 GHz 0.4 Isolation (ANT port to any receive port) (see Table 5) Iso Up to 1.0 GHz Up to 2.0 GHz Up to 2.7 GHz 30 25 20 37 30 27 dB dB dB Return loss RL All ports, up to 1.0 GHz All ports, up to 2.0 GHz All ports, up to 2.7 GHz 20 20 25 25 14 dB dB dB Triple Beat Ratio TBR 650 to 900 MHz +81 +93 dBc 1710 to 2155 MHz +81 +94 dBc (also see Table 9) 2nd Order Intermodulation IMD2 See Table 7 –110 –105 dBm 3rd Order Intermodulation IMD3 See Table 8 –110 –105 dBm nd Band 13 2 harmonic 2fo TRX1 to TRX10, PIN = +25 dBm, fo = 782 MHz –80 –78 dBm Band 17 3rd harmonic 3fo TRX1 to TRX10, PIN = +25 dBm, fo = 707 MHz –80 –78 dBm Low band 2nd harmonic 2fo TRX1 to TRX10, PIN = +27 dBm, fo = 900 MHz –80 –72 dBm Low band 3rd harmonic 3fo TRX1 to TRX10, PIN = +27 dBm, fo = 900 MHz –74 –66 dBm Skyworks Solutions, Inc. • Phone [781] 376–3000 • Fax [781] 376–3100 • [email protected] • www.skyworksinc.com 6 December 17, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202983B DATA SHEET • SKY13473-12–569LF SP10T LTE TRANSMIT/RECEIVE SWITCH WITH MIPI RFFE INTERFACE Table 4. SKY13473-12-569LF RF Electrical Specifications (2 of 2) (Note 1) (VDD = 2.85 V, TOP = +25 C, Characteristic Impedance [ZO] = 50 Ω, Unless Otherwise Noted) Parameter Symbol nd Test Condition Min Typical Max Units High band 2 harmonic 2fo TRX1 to TRX10, PIN = +27 dBm, fo = 2690 MHz –70 –62 dBm High band 3rd harmonic 3fo TRX1 to TRX10, PIN = +27 dBm, fo = 2690 MHz –68 –60 dBm Note 1: Performance is guaranteed only under the conditions listed in this Table. Table 5. SKY13473-12-569LF RF Electrical Specifications: Isolation, ANT to TRX Ports (1 of 2) (Note 1) (VDD = 2.85 V, TOP = +25 C, Characteristic Impedance [ZO] = 50 Ω, Unless Otherwise Noted) Isolation (dB) Frequency (MHz) TRX1 TRX2 TRX3 TRX4 TRX5 TRX6 TRX7 TRX8 TRX9 TRX10 TRX1 915 – –39 –43 –43 –38 –45 –49 –49 –52 –54 TRX1 1910 – –31 –32 –36 –32 –39 –43 –41 –44 –46 TRX1 2690 – –29 –28 –32 –28 –36 –39 –37 –40 –42 TRX2 915 –46 – –48 –48 –39 –45 –49 –49 –52 –53 TRX2 1910 –35 – –35 –37 –32 –39 –43 –41 –44 –46 TRX2 2690 –32 – –30 –33 –28 –36 –39 –37 –40 –42 TRX3 915 –50 –44 – –42 –41 –46 –49 –49 –52 –52 TRX3 1910 –38 –35 – –34 –32 –40 –43 –42 –44 –45 TRX3 2690 –34 –32 – –31 –28 –36 –39 –37 –40 –41 TRX4 915 –46 –47 –39 – –46 –46 –49 –49 –51 –52 TRX4 1910 –37 –34 –31 – –33 –40 –43 –42 –44 –45 TRX4 2690 –33 –29 –27 – –29 –36 –39 –37 –39 –41 TRX5 915 –45 –45 –48 –43 – –47 –50 –49 –52 –52 TRX5 1910 –37 –35 –35 –34 – –40 –43 –42 –44 –45 TRX5 2690 –33 –31 –30 –32 – –36 –39 –37 –39 –41 TRX6 915 –52 –51 –48 –47 –42 – –43 –48 –44 –45 TRX6 1910 –45 –44 –40 –41 –36 – –35 –35 –35 –37 TRX6 2690 –41 –40 –36 –37 –33 – –32 –29 –30 –32 TRX7 915 –52 –51 –47 –47 –42 –46 – –39 –46 –46 TRX7 1910 –45 –44 –40 –41 –36 –35 – –31 –34 –37 TRX7 2690 –42 –40 –36 –37 –33 –31 – –27 –29 –33 TRX8 915 –53 –51 –47 –46 –42 –43 –42 – –43 –50 TRX8 1910 –45 –44 –40 –40 –36 –34 –34 – –34 –38 TRX8 2690 –42 –40 –36 –37 –32 –30 –31 – –31 –33 Closed Path Skyworks Solutions, Inc. • Phone [781] 376–3000 • Fax [781] 376–3100 • [email protected] • www.skyworksinc.com 202983B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 17, 2013 7 DATA SHEET • SKY13473-12–569LF SP10T LTE TRANSMIT/RECEIVE SWITCH WITH MIPI RFFE INTERFACE Table 5. SKY13473-12-569LF RF Electrical Specifications: Isolation, ANT to TRX Ports (2 of 2) (Note 1) (VDD = 2.85 V, TOP = +25 C, Characteristic Impedance [ZO] = 50 Ω, Unless Otherwise Noted) Isolation (dB) Frequency (MHz) TRX1 TRX2 TRX3 TRX4 TRX5 TRX6 TRX7 TRX8 TRX9 TRX10 TRX9 915 –53 –52 –47 –46 –41 –42 –50 –47 – –43 TRX9 1910 –46 –44 –40 –40 –36 –34 –38 –34 – –34 TRX9 2690 –42 –40 –36 –37 –32 –30 –34 –30 – –31 TRX10 915 –54 –53 –47 –46 –41 –41 –45 –43 –38 – TRX10 1910 –46 –45 –40 –40 –36 –34 –37 –32 –31 – TRX10 2690 –42 –40 –36 –37 –32 –30 –33 –27 –28 – Closed Path Note 1: Performance is guaranteed only under the conditions listed in this Table. Table 6. SKY13473-12-569LF RF Electrical Specifications: Isolation, TRX to TRX Ports (1 of 2) (Note 1) (VDD = 2.85 V, TOP = +25 C, Characteristic Impedance [ZO] = 50 Ω, Unless Otherwise Noted) Isolation (dB) Frequency (MHz) TRX1 TRX2 TRX3 TRX4 TRX5 TRX6 TRX7 TRX8 TRX9 TRX10 TRX1 915 – –31 –41 –43 –52 –57 –59 –57 –53 –53 TRX1 1910 – –25 –34 –35 –39 –47 –48 –46 –44 –46 TRX1 2690 – –21 –29 –32 –35 –44 –44 –41 –40 –42 TRX2 915 –33 – –34 –39 –49 –57 –59 –57 –53 –54 TRX2 1910 –27 – –28 –32 –38 –47 –48 –46 –45 –46 TRX2 2690 –24 – –24 –29 –34 –44 –44 –41 –40 –42 TRX3 915 –39 –33 – –32 –44 –58 –59 –57 –54 –55 TRX3 1910 –33 –27 – –26 –35 –47 –48 –45 –45 –47 TRX3 2690 –29 –23 – –22 –31 –43 –44 –41 –40 –43 TRX4 915 –42 –38 –31 – –34 –58 –58 –56 –54 –55 TRX4 1910 –35 –32 –25 – –27 –46 –47 –45 –45 –47 TRX4 2690 –31 –27 –21 – –23 –42 –43 –40 –40 –43 TRX5 915 –43 –41 –37 –32 – –58 –56 –55 –54 –55 TRX5 1910 –36 –34 –30 –26 – –45 –47 –45 –45 –47 TRX5 2690 –32 –29 –26 –23 – –41 –42 –40 –40 –43 TRX6 915 –55 –54 –58 –60 –51 – –32 –37 –41 –43 TRX6 1910 –47 –45 –45 –47 –43 – –26 –30 –34 –36 TRX6 2690 –43 –40 –40 –43 –40 – –23 –26 –30 –32 TRX7 915 –55 –54 –58 –60 –50 –34 – –31 –38 –41 TRX7 1910 –47 –45 –46 –48 –43 –27 – –25 –32 –35 TRX7 2690 –43 –41 –41 –44 –40 –24 – –21 –28 –31 Closed Path Skyworks Solutions, Inc. • Phone [781] 376–3000 • Fax [781] 376–3100 • [email protected] • www.skyworksinc.com 8 December 17, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202983B DATA SHEET • SKY13473-12–569LF SP10T LTE TRANSMIT/RECEIVE SWITCH WITH MIPI RFFE INTERFACE Table 6. SKY13473-12-569LF RF Electrical Specifications: Isolation, TRX to TRX Ports (2 of 2) (Note 1) (VDD = 2.85 V, TOP = +25 C, Characteristic Impedance [ZO] = 50 Ω, Unless Otherwise Noted) Isolation (dB) Frequency (MHz) TRX1 TRX2 TRX3 TRX4 TRX5 TRX6 TRX7 TRX8 TRX9 TRX10 TRX8 915 –55 –54 –59 –61 –49 –42 –32 – –32 –39 TRX8 1910 –47 –45 –46 –48 –42 –35 –26 – –26 –33 TRX8 2690 –43 –40 –41 –44 –40 –31 –22 – –23 –29 TRX9 915 –54 –54 –59 –60 –49 –45 –39 –34 – –32 TRX9 1910 –46 –45 –46 –48 –42 –37 –32 –28 – –26 TRX9 2690 –42 –40 –41 –44 –41 –33 –28 –24 – –23 TRX10 915 –53 –53 –59 –60 –49 –47 –41 –40 –30 – TRX10 1910 –46 –44 –46 –48 –42 –38 –35 –33 –24 – TRX10 2690 –42 –40 –42 –44 –41 –34 –31 –29 –21 – Closed Path Note 1: Performance is guaranteed only under the conditions listed in this Table. Table 7. IMD2 Test Conditions Power Blocker (dBm) Receive Frequency (MHz) Frequency Blocker, Low (MHz) Frequency Blocker, High (MHz) 190 4090 2140.0 1880.0 80 3840 1960.0 1732.0 400 3864 836.5 45 1718 881.5 7 2535.0 120 5187 2655.0 8 897.0 45 1839 942.0 Band Transmit Frequency (MHz) 1 1950.0 2 4 5 Transmit Power (dBm) +20 2132.0 –15 Table 8. IMD3 Test Conditions Band Transmit Frequency (MHz) Transmit Power (dBm) 1 1950.0 1760.0 2140.0 2 1880.0 1800.0 1960.0 4 1732.0 5 836.5 791.5 881.5 7 2535.0 2415.0 2655.0 8 897.0 852.0 942.0 +20 Frequency Blocker (MHz) Power Blocker (dBm) 1332.0 Receive Frequency (MHz) 2132.0 –15 Table 9. Triple Beat Ratio Test Conditions Band Transmit Frequency 1 (MHz) 2 1880.0 5 835.5 Transmit Power 1 (dBm) +21.5 Transmit Frequency 2 (MHz) 1881.0 836.5 Transmit Power 2 (dBm) +21.5 Frequency Blocker @ ANT (MHz) 1960.0 Power Blocker (dBm) –30 881.5 TBR Product Frequency (MHz) 1960.0 ± 1 881.5 ± 1 Skyworks Solutions, Inc. • Phone [781] 376–3000 • Fax [781] 376–3100 • [email protected] • www.skyworksinc.com 202983B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 17, 2013 9 DATA SHEET • SKY13473-12–569LF SP10T LTE TRANSMIT/RECEIVE SWITCH WITH MIPI RFFE INTERFACE fBLK 1760 MHz, –15 dBm fFUND 1950 MHz, +20 dBm fRX 2140 MHz, Measure Tone Circulator Signal Generator fFUND = 1950 MHz, +20 dBm Coupler to Monitor Input Power 1950 MHz Bandpass Filter Circulator Duplexer Phase Shifter SKY13473-12-569LF fFUND = +20 dBm fBLK = –15 dBm Signal Generator fBLK = 1760 MHz, –15 dBm 1760 MHz Bandpass Filter Spectrum Analyzer fRX = 2140 MHz S1970q Figure 4. 3rd Order Intermodulation Test Setup Table 10. Command Sequence Bit Definitions Extended Operation Type SSC C11C8 C7 C6-C5 C4 C3-C0 Parity Bits BPC DA7(1)DA0(1) Parity Bits BPC DA7(n)DA0(n) Parity Bits BPC Reg0 Write Y SA[3:0] 1 Data[6:5] Data[4] Data{3:0] Y Y – – – – – – Reg Write Y SA[3:0] 0 10 Addr[4] Addr[3:0] Y – Data[7:0] – – – Y Y Reg Read Y SA[3:0] 0 11 Addr[4] Addr[3:0] Y Y Data[7:0] – – – Y Y Legend: SSC = Sequence start command C = Command frame bits DA = Data/address frame bits BPC = Bus park cycle BC = Byte count (# of consecutive addresses) Skyworks Solutions, Inc. • Phone [781] 376–3000 • Fax [781] 376–3100 • [email protected] • www.skyworksinc.com 10 December 17, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202983B DATA SHEET • SKY13473-12–569LF SP10T LTE TRANSMIT/RECEIVE SWITCH WITH MIPI RFFE INTERFACE SCLK SDATA SA3 SA2 SA1 0 SA0 SSC 1 0 A4 A3 A2 A1 A0 P Example Register Write Command Frame SCLK P SDATA D7 D6 D5 D4 D3 D2 D1 P D0 Example Data Frame 0 Bus Park Signal Driven by Master Signal Not Driven; Pull-Down Only For Reference Only S3101 Figure 5. Register Write Command Timing Diagram SCLK SDATA SA3 SA2 SA1 0 SA0 1 1 A4 A3 A2 A1 A0 P Example Register Read Command Frame SSC SCLK SDATA P 0 D7 Bus Park D6 D5 D4 D3 D2 D1 Example Data Frame D0 P 0 Bus Park Signal Driven by Master Signal Not Driven; Pull-Down Only Signal Driven by Slave For Reference Only S3102 Figure 6. Register Read Command Timing Diagram Skyworks Solutions, Inc. • Phone [781] 376–3000 • Fax [781] 376–3100 • [email protected] • www.skyworksinc.com 202983B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 17, 2013 11 DATA SHEET • SKY13473-12–569LF SP10T LTE TRANSMIT/RECEIVE SWITCH WITH MIPI RFFE INTERFACE Table 11. Register_0 Truth Table State Register_0 Bits Mode D7 D6 D5 D4 D3 D2 D1 D0 1 Isolation (default) x 0 0 0 0 0 0 0 2 TRX1 x 0 0 0 0 0 1 0 3 TRX2 x 0 0 0 1 0 1 0 4 TRX3 x 0 0 0 1 1 1 0 5 TRX4 x 0 0 0 1 0 1 1 6 TRX5 x 0 0 0 0 0 0 1 7 TRX6 x 0 0 0 1 0 0 1 8 TRX7 x 0 0 0 0 1 1 0 9 TRX8 x 0 0 0 0 1 0 0 10 TRX9 x 0 0 0 1 1 0 0 11 TRX10 x 0 0 0 1 0 0 0 Table 12. Register Description and Programming (1 of 2) Register Name Address (Hex) Register_0 0000 Parameter MODE_CTRL Default (Binary) Description Bits[7:0]: – Switch control. See Table 10 for logic SOFTWARE RESET Bit[7]: 0 Resets all data to default values except for USID, GSID, or the contents of the PM_TRIG Register. 0 = Normal operation 1 = Software reset COMMAND_FRAME_PARITY_ERR Bit[6]: COMMAND_LENGTH_ERR Bit[5]: 0 Command sequence received with parity error – discard command. 0 Command length error. ADDRESS_FRAME_PARITY_ERR RFFE_STATUS 001A Bit[4]: 0 Address frame parity error =1. DATA_FRAME_PARITY_ERR Bit[3]: 0 Data frame with parity error. READ_UNUSED_REG Bit[2]: 0 Read command to an invalid address. WRITE_UNUSED_REG Bit[1]: 0 Write command to an invalid address. BID_GID_ERR Bit[0]: 0 Read command with a BROADCAST_ID (refer to the MIPI Alliance Specification) or GSID. GROUP_SID 001B Reserved Bits[7:4]: Reserved 0000 GSID Bits[3:0]: 0000 Group slave ID Skyworks Solutions, Inc. • Phone [781] 376–3000 • Fax [781] 376–3100 • [email protected] • www.skyworksinc.com 12 December 17, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202983B DATA SHEET • SKY13473-12–569LF SP10T LTE TRANSMIT/RECEIVE SWITCH WITH MIPI RFFE INTERFACE Table 12. Register Description and Programming (2 of 2) Register Parameter Address (Hex) Name PWR_MODE Default (Binary) Description Bits[7:6]: 00 00 = Normal operation (active) 01 = Default settings (startup) 10 = Low power (low power) 11 = Reserved Trigger_Mask_2 Bit[5]: 0 If this bit is set, trigger 2 is disabled. When all triggers are disabled, if writing to a register that is associated with trigger 2, the data goes directly to the destination register. Trigger_Mask_1 PM_TRIG (Note 1) Bit[4]: 0 If this bit is set, trigger 1 is disabled. When all triggers are disabled, if writing to a register that is associated with trigger 1, the data goes directly to the destination register. 001C Trigger_Mask_0 Bit[3]: 0 If this bit is set, trigger 0 is disabled. When all triggers are disabled, if writing to a register that is associated with trigger 0, the data goes directly to the destination register. Trigger_2 Bit[2]: Trigger_1 Bit[1]: Trigger_0 Bit[0]: PRODUCT_ID Bits[7:0]: 0 If this bit is set, data is loaded into the trigger 2 registers. 0 If this bit is set, data is loaded into the trigger 1 registers. 0 If this bit is set, data is loaded into the trigger 0 registers. PRODUCT_ID 001D 01000101 This is a read-only register. However, during the programming of the Unique Slave Identifier (USID), a write command sequence is performed on this register but the value is not changed. MANUFACTURER_ID 001E MANUFACTURER_ID Bits[7:0]: 10100101 Read-only register Reserved Bits[7:6]: 00 Reserved MAN_USID 001F MANUFACTURER_ID Bits[5:4]: 01 Read-only register USID Bits[3:0]: 1010 Programmable USID. A write to these bits programs the USID. Note 1: Unlike the complete independence between triggers 0, 1, and 2, and also between the associated trigger masks 0, 1, and 2, respectively, as described in the MIPI RFFE Specification, this device uses additional interactions between the provided trigger functions. The delayed application of updated data to all triggerable registers in this device may be accomplished using any of the three triggers (0, 1, or 2), provided that the particular trigger used is not currently masked off. If multiple triggers are enabled, any or all of those are sufficient to cause the data to be transferred from shadow registers to destination registers for all triggerable registers in the device. It is also necessary to disable all three triggers (i.e., set all three trigger masks) to ensure that data written to any triggerable register will immediately be written to the destination register at the conclusion of the RFFE command sequence where the data is written. Skyworks Solutions, Inc. • Phone [781] 376–3000 • Fax [781] 376–3100 • [email protected] • www.skyworksinc.com 202983B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 17, 2013 13 DATA SHEET • SKY13473-12–569LF SP10T LTE TRANSMIT/RECEIVE SWITCH WITH MIPI RFFE INTERFACE Evaluation Board Description Package and Handling Information The SKY13473-12-569LF Evaluation Board is used to test the performance of the SKY13473-12-569LF SP10T Switch. An Evaluation Board schematic diagram is provided in Figure 7. A recommended ESD protection circuit diagram is provided in Figure 8. An assembly drawing for the Evaluation Board is shown in Figure 9. Instructions on the shipping container label regarding exposure to moisture after the container seal is broken must be followed. Otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly. The SKY13473-12-569LF is rated to Moisture Sensitivity Level 1 (MSL1) at 260 C. It can be used for lead or lead-free soldering. For additional information, refer to the Skyworks Application Note, PCB Design and SMT Assembly/Rework Guidelines for MCM-L Packages, document number 101752. Package Dimensions The PCB layout footprint for the SKY13473-12-569LF is provided in Figure 10. Typical case markings are shown in Figure 11. Package dimensions for the 20-pin QFN are shown in Figure 12, and tape and reel dimensions are provided in Figure 13. Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. Production quantities of this product are shipped in a standard tape and reel format. 1 2 3 4 5 VDD VIO SDATA SCLK N/C GND DCH1 Header 6 × C1 33 pF C3 33 pF 2 RFC11 VDD 17 VIO N/C 18 SDATA × 19 SCLK 20 1 C2 10 nF GND TRX10 TRX1 TRX9 TRX2 TRX8 TRX3 TRX7 TRX4 3 RFC10 4 RFC9 7 8 GND ANT TRX6 GND GND 6 RFC7 15 RFC1 14 5 RFC8 16 9 TRX5 RFC2 13 12 RFC3 RFC4 11 RFC5 10 RFC6 S3084 Figure 7. SKY13473-12-569LF Evaluation Board Schematic Skyworks Solutions, Inc. • Phone [781] 376–3000 • Fax [781] 376–3100 • [email protected] • www.skyworksinc.com 14 December 17, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202983B DATA SHEET • SKY13473-12–569LF SP10T LTE TRANSMIT/RECEIVE SWITCH WITH MIPI RFFE INTERFACE 4.7 pF To Application Antenna To SKY13473-12-569LF Antenna (Pin 9) 18 nH 18 nH ESD Circuit 1 12 pF To Application Antenna To SKY13473-12-569LF Antenna (Pin 9) 12 nH ESD Circuit 2 S2520k Figure 8. SKY13473-12-569LF Recommended ESD Protection Circuits TRX2 TRX3 TRX1 TRX4 TRX5 VDD VIO SDAT A SCL K N/C GND ANT TRX6 TRX7 TRX10 TRX9 TRX8 Y0080 Figure 9. SKY13473-12-569LF Evaluation Board Assembly Diagram Skyworks Solutions, Inc. • Phone [781] 376–3000 • Fax [781] 376–3100 • [email protected] • www.skyworksinc.com 202983B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 17, 2013 15 DATA SHEET • SKY13473-12–569LF SP10T LTE TRANSMIT/RECEIVE SWITCH WITH MIPI RFFE INTERFACE 5X 0.400 Pitch Pin 20 R0.200 Pin 1 Indicator 8X 0.900 20X 0.225 Pin 1 20X 0.300 6X 0.400 Pitch 2X 0.700 12X 0.900 Package Outline Exposed Solder Area 2X 0.700 All dimensions are in millimeters S3292 Figure 10. SKY13473-12-569LF PCB Layout Footprint (Top View) Pin 1 Indicator Skyworks Part # Lot # Figure 11. Typical Part Markings (Top View) Skyworks Solutions, Inc. • Phone [781] 376–3000 • Fax [781] 376–3100 • [email protected] • www.skyworksinc.com 16 December 17, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202983B DATA SHEET • SKY13473-12–569LF SP10T LTE TRANSMIT/RECEIVE SWITCH WITH MIPI RFFE INTERFACE 8X 0.20 Seating Plane A C 2.40 0.02 + 0.02/–0.05 (0.11) Pin 1 Indicator R0.20 Pin 1 Indicator 8X 0.60 Exposed Pad 20 1 16 20X 0.25 Min. 2.40 1.3 ± 0.1 (0.65) 24X 1.00 20X 0.05 C 2X B 2X 6 11 2 See Detail A 0.05 C (0.65) 0.05 C 0.75 ± 0.05 1.3 ± 0.1 0.05 C Top View Side View Bottom View 4 0.2 ± 0.05 0.10 M C A B 0.2 ± 0.05 R0.020 4X Detail A Scale: 80X 4X This Rotation 4X Rotated 180° 6X Rotated 90° CW 6X Rotated 90° CCW All measurements are in millimeters. Dimensioning and tolerancing according to ASME Y14.5M-1994. Coplanarity applies to the terminals and all other bottom surface metalization. Dimension applies to metalized terminal. If the terminal has a radius on its end, the width dimension should not be measured in that radius area. S3080 B ∅1.5 2.00 ± 0.05 4.00 ± 0.10 2.70 ± 0.10 (Bo) 3.50 ± 0.05 0.25 ± 0.05 + 0.10 –0 1.00 ± 0.10 (Ko) A 8.00 + 0.30/–0.10 1.75 ± 0.10 (E) Figure 12. SKY13473-12-569LF 20-Pin QFN Package Dimensions A Pin 1 Indicator B 4.00 ± 0.10 Section B 2.70 ± 0.10 (Ao) Notes: ∅1.00 + 0.10 –0 2.00 ± 0.05 1. Carrier tape material: black conductive polystyrene. 2. Cover tape material: transparent conductive material. 3. 10 sprocket hole pitch cumulative tolerance: ± 0.20 mm. 4. Ao and Bo measured on plane 0.30 mm above the bottom of the pocket. 5. All dimensions are in millimeters. Section A Y0079 Figure 13. SKY13473-12-569LF Tape and Reel Dimensions Skyworks Solutions, Inc. • Phone [781] 376–3000 • Fax [781] 376–3100 • [email protected] • www.skyworksinc.com 202983B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 17, 2013 17 DATA SHEET • SKY13473-12–569LF SP10T LTE TRANSMIT/RECEIVE SWITCH WITH MIPI RFFE INTERFACE Ordering Information Model Name SKY13473-12-569LF 0.4 to 2.7 GHz SP10T LTE Transmit/Receive Switch with MIPI RFFE Interface Manufacturing Part Number SKY13473-12-569LF Evaluation Board Part Number SKY13473-12-569LF-EVB Copyright © 2013 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks, the Skyworks symbol, and “Breakthrough Simplicity” are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. • Phone [781] 376–3000 • Fax [781] 376–3100 • [email protected] • www.skyworksinc.com 18 December 17, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202983B