MIC5207 180mA Low-Noise LDO Regulator Features General Description The MIC5207 is an efficient linear voltage regulator with ultra-low-noise output, very low dropout voltage (typically 17mV at light loads and 165mV at 150mA), and very low ground current (720µA at 100mA output). The MIC5207 offers better than 3% initial accuracy. Designed especially for hand-held, battery-powered devices, the MIC5207 includes a CMOS or TTL compatible enable/shutdown control input. When in shutdown, power consumption drops nearly to zero. Key MIC5207 features include a reference bypass pin to improve its already low-noise performance, reversedbattery protection, current limiting, and over temperature shutdown. The MIC5207 is available in fixed and adjustable output voltage versions in a small SOT-23-5 package. Contact Micrel for details. For low-dropout regulators that are stable with ceramic output capacitors, see the µCap MIC5245/6/7 family. Datasheets and support documentation are available on Micrel’s web site at: www.micrel.com. • • • • • • • • • • • • Output voltage range: 1.8V – 15V Ultra-low-noise output High output voltage accuracy Guaranteed 180mA output Low quiescent current Low dropout voltage Extremely tight load and line regulation Very low temperature coefficient Current and thermal limiting Reversed-battery protection “Zero” off-mode current Logic-controlled electronic enable Applications • • • • • • • Cellular telephones Laptop, notebook, and palmtop computers Battery-powered equipment PCMCIA VCC and VPP regulation/switching Consumer/personal electronics SMPS post-regulator/dc-to-dc modules High-efficiency linear power supplies Typical Application Battery-Powered Regulator Application Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com January 22, 2015 Revision 1.1 Micrel, Inc. MIC5207 Ordering Information Marking(2) Voltage(1) Junction Temp. Range Package Lead Finish MIC5207-1.8YD5 NE18 1.8V 0° to +125°C 5-Pin Thin SOT-23 Pb-Free MIC5207YM5 LEAA Adj. (2.5–15.0V) –40° to +125°C Adj. (1.8–2.5V) 0° to +125°C 5-Pin SOT-23 Pb-Free MIC5207-1.8YM5 LE18 1.8V 0° to +125°C 5-Pin SOT-23 Pb-Free MIC5207-2.5YM5 LE25 2.5V –40° to +125°C 5-Pin SOT-23 Pb-Free MIC5207-2.8YM5 LE28 2.8V –40° to +125°C 5-Pin SOT-23 Pb-Free MIC5207-2.9YM5 LE29 2.9V –40° to +125°C 5-Pin SOT-23 Pb-Free MIC5207-3.0YM5 LE30 3.0V –40° to +125°C 5-Pin SOT-23 Pb-Free MIC5207-3.1YM5 LE31 3.1V –40° to +125°C 5-Pin SOT-23 Pb-Free MIC5207-3.2YM5 LE32 3.2V –40° to +125°C 5-Pin SOT-23 Pb-Free MIC5207-3.3YM5 LE33 3.3V –40° to +125°C 5-Pin SOT-23 Pb-Free MIC5207-3.6YM5 LE36 3.6V –40° to +125°C 5-Pin SOT-23 Pb-Free MIC5207-3.8YM5 LE38 3.8V –40° to +125°C 5-Pin SOT-23 Pb-Free MIC5207-4.0YM5 LE40 4.0V –40° to +125°C 5-Pin SOT-23 Pb-Free MIC5207-5.0YM5 LE50 5.0V –40° to +125°C 5-Pin SOT-23 Pb-Free Part Number Note: 1. Other voltages available. Contact Micrel for details. 2. Under bar ( __ ) symbol may not be to scale. January 22, 2015 2 Revision 1.1 Micrel, Inc. MIC5207 Pin Configuration MIC5207YM5 (M5) (Adjustable Voltage) MIC5207-x.xYM5 (M5) MIC5207-x.xYD5 (D5) (Fixed Voltage) Pin Description Pin Number SOT-23-5 Pin Name 1 IN 2 GND 3 EN Enable/Shutdown (Input): CMOS compatible input. Logic high = enable, logic low = shutdown. Do not leave floating. 4 (fixed) BYP Reference Bypass: Connect external 470pF capacitor to GND to reduce output noise. May be left open. For 1.8V or 2.5V operation, see “Applications Information”. 4 (adj.) ADJ Adjust (Input): Adjustable regulator feedback input. Connect to resistor voltage divider. 5 OUT Regulator Output. January 22, 2015 Pin Name Supply Input. Ground. 3 Revision 1.1 Micrel, Inc. MIC5207 Absolute Maximum Ratings(3) Operating Ratings(4) Supply Input Voltage (VIN) .............................. –20V to +20V Enable Input Voltage (VEN) ............................. –20V to +20V Power Dissipation (PD) ........................... Internally Limited(5) Lead Temperature (soldering, 5 sec) ......................... 260°C Junction Temperature (TJ) All except 1.8V .................................... –40°C to +125°C 1.8V ONLY.............................................. 0°C to +125°C Storage Temperature (TS) ......................... –65°C to +150°C Supply Input Voltage (VIN) ............................. +2.5V to +16V Adjustable Output Voltage (VOUT) Range .......... 1.8V to 15V Enable Input Voltage (VEN) .................................... 0V to VIN Junction Temperature (TJ) 2.5 ≤ VOUT ≤ 15V ................................. –40°C to +125°C 1.8V ≤ VOUT < 2.5V .................................. 0°C to +125°C Thermal Resistance (θJA) .......................................... Note 5 Electrical Characteristics VIN = VOUT + 1V; IL = 100µA; CL = 1.0µF; VEN ≥ 2.0V; TJ = 25°C, bold values indicate –40°C < TJ < +125°C except 0°C < TJ < +125°C for 1.8V, unless noted. Symbol Parameter Condition VO Output Voltage Accuracy Variation from nominal VOUT ∆VO/∆T Output Voltage Temperature Coefficient Note 6 ∆VO/VO Line Regulation VIN = VOUT + 1V to 16V ∆VO/VO Load Regulation IL = 0.1mA to 150mA, Note 7 VIN – VO IGND Dropout Voltage, Note 8 Quiescent Current Min Typ –3 –4 Max Units 3 4 % % 40 ppm/°C 0.005 0.05 0.10 %/V %/V 0.05 0.5 0.7 % % IL = 100µA 17 IL = 50mA 115 IL = 100mA 140 IL = 150mA 165 60 80 175 250 280 325 300 400 mV mV mV mV mV mV mV mV VEN ≤ 0.4V (shutdown) VEN ≤ 0.18V (shutdown) 0.01 1 5 µA µA Notes: 3. Exceeding the absolute maximum rating may damage the device. 4. The device is not guaranteed to function outside its operating rating. 5. The maximum allowable power dissipation at any TA (ambient temperature) is PD(max) = (TJ(max) –TA) / θJA. Exceeding the maximum allowable power dissipation will cause excessive die temperature, and the regulator will go into thermal shutdown. The θJA of the SOT-23-5 (M5) is 235°C/W soldered on a PC board (see “Thermal Considerations” for further details). 6. Output voltage temperature coefficient is defined as the worst case voltage change divided by the total temperature range. 7. Regulation is measured at constant junction temperature using low duty cycle pulse testing. Parts are tested for load regulation in the load range from 0.1mA to 180mA. Changes in output voltage due to heating effects are covered by the thermal regulation specification. 8. Dropout Voltage is defined as the input to output differential at which the output voltage drops 2% below its nominal value measured at 1V differential. January 22, 2015 4 Revision 1.1 Micrel, Inc. MIC5207 Electrical Characteristics (Continued) VIN = VOUT + 1V; IL = 100µA; CL = 1.0µF; VEN ≥ 2.0V; TJ = 25°C, bold values indicate –40°C < TJ < +125°C except 0°C < TJ < +125°C for 1.8V, unless noted. Symbol Parameter Condition IGND Ground Pin Current, Note 9 Min Typ Max Units VEN ≥ 2.0V, IL = 100µA 80 IL = 50mA 350 IL = 100mA 720 IL = 150mA 1800 130 170 650 900 1100 2000 2500 3000 µA µA µA µA µA µA µA µA PSRR Ripple Rejection 75 dB ILIMIT Current Limit VOUT = 0V 320 ∆VO/∆PD Thermal Regulation Note 10 0.05 %/W eno Output Noise IL = 50mA, CL = 2.2µF, 470pF from BYP to GND 260 nV√Hz 500 mA Enable Input VIL Enable Input Logic-Low Voltage Regulator shutdown VIH Enable Input Logic-High Voltage Regulator enable IIL Enable Input Current VIL ≤ 0.4V VIL ≤ 0.18V VIH ≥ 2.0V VIH ≥ 2.0V IIH 0.4 0.18 V V 2.0 V 0.01 5 –1 –2 20 25 µA µA µA µA Notes: 9. Ground pin current is the regulator quiescent current plus pass transistor base current. The total current drawn from the supply is the sum of the load current plus the ground pin current. 10. Thermal regulation is defined as the change in output voltage at a time “t” after a change in power dissipation is applied, excluding load or line regulation effects. Specifications are for a 180mA load pulse at VIN = 16V for t = 10ms. January 22, 2015 5 Revision 1.1 Micrel, Inc. MIC5207 Typical Characteristics January 22, 2015 6 Revision 1.1 Micrel, Inc. MIC5207 Typical Characteristics (Continued) 10 Noise Performance 10mA, COUT = 1µF NOISE (µV/ Hz) 1 0.1 0.01 1mA COUT = 1µF CBYP = 10nF 0.001 VOUT = 5V 0.0001 1E+11E+21E+3 10 100 1k 1E+4 10M 100k 1M 1E+7 10k 1E+51E+6 FREQUENCY (Hz) 10 Noise Performance NOISE (µV/ Hz) 1 100mA 0.1 0.01 1mA VOUT = 5V COUT = 10µF 0.001 electrolytic 10mA CBYP = 100pF 0.0001 1E+11E+21E+3 10k 1E+5 100k 1E+61E+7 1M 10M 10 100 1k 1E+4 FREQUENCY (Hz) January 22, 2015 7 Revision 1.1 Micrel, Inc. MIC5207 Block Diagrams Ultra-Low-Noise Fixed Regulator Ultra-Low-Noise Adjustable Regulator January 22, 2015 8 Revision 1.1 Micrel, Inc. MIC5207 No-Load Stability The MIC5207 will remain stable and in regulation with no load (other than the internal voltage divider) unlike many other voltage regulators. This is especially important in CMOSRAM keep-alive applications. Application Information Enable/Shutdown Forcing EN (enable/shutdown) high (> 2V) enables the regulator. EN is compatible with CMOS logic gates. If the enable/shutdown feature is not required, connect EN (pin 3) to IN (supply input, pin 1). See Figure 1. Thermal Considerations The MIC5207 is designed to provide 180mA of continuous current in a very small package. Maximum power dissipation can be calculated based on the output current and the voltage drop across the part. To determine the maximum power dissipation of the package, use the junction-to-ambient thermal resistance of the device and the following basic equation shown in Equation 1: Input Capacitor A 1µF capacitor should be placed from IN to GND if there is more than 10 inches of wire between the input and the ac filter capacitor or if a battery is used as the input. Reference Bypass Capacitor BYP (reference bypass) is connected to the internal voltage reference. A 470pF capacitor (CBYP) connected from BYP to GND quiets this reference, providing a significant reduction in output noise. CBYP reduces the regulator phase margin; when using CBYP, output capacitors of 2.2µF or greater are generally required to maintain stability. PD(MAX) = (TJ(MAX) − TA ) θ JA Eq. 1 TJ(max) is the maximum junction temperature of the die, 125°C, and TA is the ambient operating temperature. θJA is layout dependent; Table 1 shows examples of junctionto-ambient thermal resistance for the MIC5207. The start-up speed of the MIC5207 is inversely proportional to the size of the reference bypass capacitor. Applications requiring a slow ramp-up of output voltage should consider larger values of CBYP. Likewise, if rapid turn-on is necessary, consider omitting CBYP. Table 1. SOT-23-5 Thermal Resistance If output noise is not a major concern, omit CBYP and leave BYP open. Output Capacitor An output capacitor is required between OUT and GND to prevent oscillation. The minimum size of the output capacitor is dependent upon whether a reference bypass capacitor is used. 1.0µF minimum is recommended when CBYP is not used (see Figure 2). 2.2µF minimum is recommended when CBYP is 470pF (see Figure 1). Larger values improve the regulator’s transient response. The output capacitor value may be increased without limit. Package θJA Recommemded Minimum Footprint θJA 1” Square Copper Clad θJ/C SOT-23-5 (M5) 235°C/W 170°C/W 130°C/W The actual power dissipation of the regulator circuit can be determined using Equation 2: PD = (VIN − VOUT ) IOUT + VIN IGND Eq. 2 Substituting PD(max) for PD and solving for the operating conditions that are critical to the application will give the maximum operating conditions for the regulator circuit. For example, when operating the MIC5207-3.3YM5 at room temperature with a minimum footprint layout, the maximum input voltage for a set output current can be determined with Equation 3: The output capacitor should have an ESR (effective series resistance) of about 5Ω or less and a resonant frequency above 1MHz. Ultra-low-ESR (ceramic) capacitors can cause a low amplitude oscillation on the output and/or under-damped transient response. Most tantalum or aluminum electrolytic capacitors are adequate; film types will work, but are more expensive. Since many aluminum electrolytics have electrolytes that freeze at about –30°C, solid tantalums are recommended for operation below –25°C. PD(MAX) = 125°C − 25°C 235°C/W Eq. 3 PD(MAX) = 425mW At lower values of output current, less output capacitance is required for output stability. The capacitor can be reduced to 0.47µF for current below 10mA or 0.33µF for currents below 1mA. January 22, 2015 9 Revision 1.1 Micrel, Inc. MIC5207 The junction-to-ambient thermal resistance for the minimum footprint is 235°C/W, from Table 1. The maximum power dissipation must not be exceeded for proper operation. Using the output voltage of 3.3V and an output current of 150mA, the maximum input voltage can be determined. From the Electrical Characteristics table, the maximum ground current for 150mA output current is 3000µA or 3mA. Fixed Regulator Applications 455mW = (VIN − 3.3V ) 150mA + VIN ⋅ 3mA 455mW = VIN ⋅ 150mA - 495mW + VIN ⋅ 3mA Figure 1. Ultra-Low-Noise Fixed Voltage Application 920mW = VIN ⋅ 153mA Figure 1 includes a 470pF capacitor for ultra-low-noise operation and shows EN (pin 3) connected to IN (pin 1) for an application where enable/shutdown is not required. COUT = 2.2µF minimum. VIN(MAX) = 6.01V Therefore, a 3.3V application at 150mA of output current can accept a maximum input voltage of 6V in a SOT-23-5 package. For a full discussion of heat sinking and thermal effects on voltage regulators, refer to the Regulator Thermals section of Micrel’s Designing with Low-Dropout Voltage Regulators handbook Low-Voltage Operation The MIC5207-1.8 and MIC5207-2.5 require special consideration when used in voltage-sensitive systems. They may momentarily overshoot their nominal output voltages unless appropriate output and bypass capacitor values are chosen. During regulator power up, the pass transistor is fully saturated for a short time, while the error amplifier and voltage reference are being powered up more slowly from the output (see Block Diagrams). Selecting larger output and bypass capacitors allows additional time for the error amplifier and reference to turn on and prevent overshoot. To ensure that no overshoot is present when starting up into a light load (100µA), use a 4.7µF output capacitance and 470pF bypass capacitance. This slows the turn-on enough to allow the regulator to react and keep the output voltage from exceeding its nominal value. At heavier loads, use a 10µF output capacitance and 470pF bypass capacitance. Lower values of output and bypass capacitance can be used, depending on the sensitivity of the system. Applications that can withstand some overshoot on the output of the regulator can reduce the output capacitor and/or reduce or eliminate the bypass capacitor. Applications that are not sensitive to overshoot due to power-on reset delays can use normal output and bypass capacitor configurations. Please note the junction temperature range of the regulator with an output less than 2.5V fixed and adjustable is 0°C to +125°C. Figure 2. Low-Noise Fixed Voltage Application Figure 2 is an example of a basic low-noise configuration. COUT = 1µF minimum. Adjustable Regulator Applications The MIC5207YM5 can be adjusted to a specific output voltage by using two external resistors (Figure 3). The resistors set the output voltage based on Equation 4: R2 VOUT = VREF 1 + , VREF = 1.242V R1 Eq. 4 This equation is correct due to the configuration of the bandgap reference. The bandgap voltage is relative to the output, as seen in the Block Diagrams. Traditional regulators normally have the reference voltage relative to ground; therefore, their equations are different from the equation for the MIC5207YM5. Resistor values are not critical because ADJ (adjust) has a high input impedance, but for best results use resistors of 470kΩ or less. A capacitor from ADJ to ground provides greatly improved noise performance. Figure 3. Ultra-Low-Noise Adjustable Voltage Application Figure 3 includes the optional 470pF noise bypass capacitor from ADJ to GND to reduce output noise. January 22, 2015 10 Revision 1.1 Micrel, Inc. MIC5207 Dual-Supply Operation When used in dual-supply systems where the regulator load is returned to a negative supply, the output voltage must be diode clamped to ground. USB Application Figure 4 shows the MIC5207-3.3YM5 in a USB application. Since the VBUS supply may be greater than 10 inches from the regulator, a 1µF input capacitor is included. Figure 4. Single-Port Self-Powered Hub January 22, 2015 11 Revision 1.1 Micrel, Inc. MIC5207 Package Information(11) 5-Pin SOT-23 (M5) January 22, 2015 12 Revision 1.1 Micrel, Inc. MIC5207 Package Information(11) (Continued) 5-Pin Thin SOT-23 (D5) Note: 11. Package information is correct as of the publication date. For updates and most current information, go to www.micrel.com. January 22, 2015 13 Revision 1.1 Micrel, Inc. MIC5207 MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http://www.micrel.com Micrel, Inc. is a leading global manufacturer of IC solutions for the worldwide high performance linear and power, LAN, and timing & communications markets. The Company’s products include advanced mixed-signal, analog & power semiconductors; high-performance communication, clock management, MEMs-based clock oscillators & crystal-less clock generators, Ethernet switches, and physical layer transceiver ICs. Company customers include leading manufacturers of enterprise, consumer, industrial, mobile, telecommunications, automotive, and computer products. Corporation headquarters and state-of-the-art wafer fabrication facilities are located in San Jose, CA, with regional sales and support offices and advanced technology design centers situated throughout the Americas, Europe, and Asia. Additionally, the Company maintains an extensive network of distributors and reps worldwide. Micrel makes no representations or warranties with respect to the accuracy or completeness of the information furnished in this datasheet. This information is not intended as a warranty and Micrel does not assume responsibility for its use. Micrel reserves the right to change circuitry, specifications and descriptions at any time without notice. No license, whether express, implied, arising by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Micrel’s terms and conditions of sale for such products, Micrel assumes no liability whatsoever, and Micrel disclaims any express or implied warranty relating to the sale and/or use of Micrel products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright, or other intellectual property right. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. © 2001 Micrel, Incorporated. January 22, 2015 14 Revision 1.1