Part Number: LMDK11D14V T-1 (3mm) SOLID STATE LAMP www.SunLED.com Package Schematics Features ● Radial / Through hole package ● Reliable & robust ● Low power consumption ● Available on tape and reel ● 14V internal resistor. ● RoHS Compliant ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES D E Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25(0.01") unless otherwise noted. 3. Specifications are subject to change without notice. Absolute Maximum Ratings (TA=25°C) L n MDK (AlGaInP) Unit V u S Reverse Voltage VR 5 Forward Voltage VF 16 Power Dissipation PD 160 Operating Temperature TA -40 ~ +70 Tstg -40 ~ +85 Storage Temperature 260°C For 3 Seconds Lead Solder Temperature [5mm Below Package Base] 260°C For 5 Seconds Part Number LMDK11D14V Emitting Color Red MDK (AlGaInP) Unit Forward Current (Typ.) (VF=14V) IF 10.5 mA mW Forward Current (Max.) (VF=14V) IF 13.5 mA °C Reverse Current (Max.) (VR=5V) IR 10 uA Wavelength of Peak Emission CIE127-2007* (Typ.) (VF=14V) λP 645* nm Wavelength of Dominant Emission CIE127-2007* (Typ.) (VF=14V) λD 630* nm Spectral Line Full Width At Half-Maximum (Typ.) (VF=14V) △λ 28 nm V Lead Solder Temperature [2mm Below Package Base] Operating Characteristics (TA=25°C) Emitting Material AlGaInP Lens-color Red Diffused Luminous Intensity CIE127-2007* (VF=14V) mcd min. typ. 120 30* 248 59* Wavelength CIE127-2007* nm λP Viewing Angle 2θ 1/2 645* 40° *Luminous intensity value and wavelength are in accordance with CIE127-2007 standards. Dec 21,2013 SDSA7960 V3-X Layout: Maggie L. P. 1/3 Part Number: LMDK11D14V T-1 (3mm) SOLID STATE LAMP www.SunLED.com MDK u S L n D E Remarks: If special sorting is required (e.g. binning based on Luminous intensity/ luminous flux, or wavelength), the typical accuracy of the sorting process is as follows: 1. Wavelength: +/-1nm 2. Luminous intensity/ luminous flux: +/-15% Note: Accuracy may depend on the sorting parameters. Dec 21,2013 SDSA7960 V3-X Layout: Maggie L. P. 2/3 Part Number: LMDK11D14V T-1 (3mm) SOLID STATE LAMP www.SunLED.com PACKING & LABEL SPECIFICATIONS D E L n u S TERMS OF USE 1. Data presented in this document reflect statistical figures and should be treated as technical reference only. 2. Contents within this document are subject to improvement and enhancement changes without notice. 3. The product(s) in this document are designed to be operated within the electrical and environmental specifications indicated on the datasheet. User accepts full risk and responsibility when operating the product(s) beyond their intended specifications. 4. The product(s) described in this document are intended for electronic applications in which a person’s life is not reliant upon the LED. Please consult with a SunLED representative for special applications where the LED may have a direct impact on a person’s life. 5. The contents within this document may not be altered without prior consent by SunLED. 6. Additional technical notes are available at http://www.SunLED.com/TechnicalNotes Dec 21,2013 SDSA7960 V3-X Layout: Maggie L. P. 3/3