MICRO TILT SENSOR D6B Subminiature PCB Mounting Sensor Discriminating Left or Right Tilt. Detects the inclination of the Sensor within an activated angle range between 45 ˚ and 75 ˚ (left and right) and a reset angle range between 50 ˚ and 20 ˚. A subminiature SMD PCB mounting model. A highly reliable solid-state type by Hall IC. A surprisingly low power consumption with a maximum of 20µA. Back and forth tilt Ordering Output configuration ON/OFF Model D6B-1 Application Left and right tilt Vertical or horizontal discrimination of digital cameras, PDAs, and cellular phones. Horizontal state Performance Activated angle Reset angle 45 ˚ to 75 ˚ (left and right) 50 ˚ and 20 ˚ (left and right) Operating characteristics Note: Characteristic values are provided, on condition that there is no tilt back and forth while the operation speed is 10 ˚ per second. Horizontal state Reset Activated High High Reset High Activated High Direction of gravity Low Low Output configuration Horizontal state High-voltage signal output from the terminals on both sides. Inclined left or right Low-voltage signal output only from the terminals on the side of the moving direction. Electrical characteristics Ta = 25˚ and Vdd = 3V DC Power supply voltage range (Vdd) High-voltage output Low-voltage output Current consumption Maximum ratings Power supply voltage (Vdd) Output current (lout) 2.7 to 3.3 V DC Vdd-0.5V min. 0.5V DC max. 20 µA max. (10 µA typical) -0.1 to 5.0 V ± 1mA Basic specifications Ambient temperature (operating) -10 cC to 60 ˚C (with no condensation) Ambient temperature (storage) -25 ˚C to 70 ˚C (with no condensation) Ambient humidity (operating) 25% to 85% D6B D6B Electrical Connections Soldering Conditions Vcc or Vref I/O port (1) or A/D conversion port (1) I/O port (2) or A/D conversion port (2) GND Microcontroller Reflow (Infrared) Soldering Conditions Weld a thermocouple on the terminal side of the Sensor with HMP (high melting point) solder, place the Sensor into the reflow oven and set the reflow oven so that the peak terminal temperature will be 230 ˚C ± 5 ˚C. The peak terminal temperature must not exceed 240 ˚C. Dismounting Conditions with Blower Employed Dismount the Sensor at a temperature of 240 ˚C within five seconds. If a soldering iron is applied manually, dismount the Sensor within 10 seconds at an iron tip temperature of 260 ˚C or within three seconds at an iron tip temperature of 350 ˚C. Rear side External Dimensions D6B-1 6.4 5.5 1.65±0.15 1.65±0.15 3.7 PCB Mounting Dimensions 0.3 3.5 3.5 0.7 0.95 3-0.2 0.7 0.4 0.95 5.5 1 0.9 1.4 3.5±0.1 0.9 1.4 3.65 1.7 3.1±0.1 0.25 Cautions • The Sensor does not use any materials detrimental to the ozone layer. • Specifications other than the electrical or mechanical characteristics, external dimensions, or mounting dimensions of the Sensor are subject to change without notice. Handling Precautions Operating Environment • The Sensor consists of a Hall IC and a magnet. Check that the Sensor in operation will not be influenced by any external magnetic fields. • Do not install any magnetic materials within 2 mm of the Sensor, else the performance characteristics of the Sensor may not be guaranteeable. If there are any objects (e.g., motors and solenoids) generating magnetic fields near the Sensor, operate and test the Sensor before the Sensor comes into actual use. • Do not apply any voltage exceeding 5V to the Sensor, else the Sensor may break. • Do not wash the Sensor after the Sensor is soldered. • Do not mount or dismount the Sensor while power is flowing to the Sensor. • The Sensor may generate error signals if impacted at a minimum acceleration of 294 m/s2. • The Sensor may generate error signals if a vibration at a minimum frequency of 15 Hz and a minimum acceleration of 15m/s2 is applied to the Sensor. • Confirm that no static electricity at a maximum voltage of 5kV is applied to the pins, else the Sensor may break. Operating Characteristics The present output may be kept if the inclination of the Sensor back and forth is 20 ˚ or over. Under that condition, the output may not change even when the Sensor is leaned left or right. (Example) 20 min. 20 min. Direction of gravity If the Sensor is kept inclined back or forth as shown in the above illustration, the level of output may not change from high to low or low to high when the Sensor inclines left or right. ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, mulitiply by 0.03527. Cat. No.F060-E1-01 In the interest of product imrovement, specifications are subject to change without notice. OMRON Corporation Electronics Components Company Electronic & Mechanical Components Division H.Q. C&C Sensor Department Shiokoji Horikawa, Shimogyo-ku, 2Kyoto, 600-8530 Japan Phone:(81)75-344-7096 Fax: (81) 75-344-7049 Printed in Japan 1002-1M (1002) W