60 MHz SAW Differential delay Line 6 MHz Bandwidth Part Number

60 MHz SAW Differential delay Line
6 MHz Bandwidth
Part Number: SD0060CN02270T
DESCRIPTION
•
•
•
60 MHz SAW differential delay line with 6 MHz bandwidth.
22.1 x 12.7 mm DIP.
RoHS compliant.
TYPICAL PERFORMANCE
Horizontal:
Vertical from top:
Frequency :
Relative Magnitude :
Relative magnitude :
Phase Linearity :
Group Delay Deviation :
5
10
1
5
50
MHz/div
dB/div
dB/div
deg/div
ns/div
Spectrum Microwave
400 Nickerson Road, Marlborough, MA 01752, USA • Phone 1-508-251-6400 • Fax 1-508-251-6401
www.SpectrumMicrowave.com
DSSD0060CN02270T Rev B 9-Feb-2010
ECN 36650 Page 1 of 3
60 MHz SAW Differential delay Line
6 MHz Bandwidth
Part Number: SD0060CN02270T
SPECIFICATION
Parameter
Center Frequency (Fc) 1
Insertion Loss at 60 MHz
Amplitude Variation (57.0 to 63.0 MHz)
Delay Time of Short Path
Delay Time of Long Path
Lower 3dB Band Edge
Upper 3dB Band Edge
Short/Long Path Integration Loss Difference
Average Differential Delay (Pins 1 to 7)
Temperature Coefficient of Delay
Source and Load Impedance
Ambient Temperature
Notes:
Min
0.620
0.870
63.00
248
-
Typ
60.00
31
2.1
0.650
0.900
56.35
63.95
1.3
250
23
50
25
Max
34
3
0.680
0.930
57.00
2.0
252
-
Units
MHz
dB
dB p-p
usec
usec
MHz
MHz
dB
nsec
ppm/°C
Ω
°C
1. All specified bandwidths are referenced to this frequency.
MAXIMUM RATINGS
Parameter
Storage Temperature Range
Operating Temperature Range
Input Power Level
Min
Max
-55
-55
85
85
15
Units
˚C
˚C
dBm
MATCHING CIRCUIT
Input
50 Ω
Single-ended
GND
Typical component values:
(Minimum inductor Q = 40)
Ls1 =
Ls3 =
330
390
Short delay Output
50 Ω
Single-ended
8
7
14
1
nH
nH
Long Delay Output
50 Ω
Single-ended
Ls2 =
390
nH
Notes:
1. Recommend use of 2% tolerance matching components.
2. Component values may change depending on board layout.
Spectrum Microwave
400 Nickerson Road, Marlborough, MA 01752, USA • Phone 1-508-251-6400 • Fax 1-508-251-6401
www.SpectrumMicrowave.com
DSSD0060CN02270T Rev B 9-Feb-2010
ECN 36650 Page 2 of 3
60 MHz SAW Differential delay Line
6 MHz Bandwidth
Part Number: SD0060CN02270T
PACKAGE OUTLINE
Units: mm
Tolerances are ±0.15 mm except
for the overall length, width and
pad dimensions, which are nominal
values.
Pin Configuration:
Input:
Output (short Delay):
Output (Long delay):
Ground:
8
7
1
2,9,14
ISO 9001
Registered
All specifications are believed to be accurate and reliable. However, Spectrum Microwave reserves the right to make changes without notice.
© 2010 All rights reserved.
Spectrum Microwave
400 Nickerson Road, Marlborough, MA 01752, USA • Phone 1-508-251-6400 • Fax 1-508-251-6401
www.SpectrumMicrowave.com
DSSD0060CN02270T Rev B 9-Feb-2010
ECN 36650 Page 3 of 3