ROHM BA6893AK

Optical disc ICs
4-channel driver and power
controller
BA6893AK
The BA6893AK is a 4-channel driver and power supply that includes the reset, recharge, and shock detection circuits
required for portable CD players on a single IC. The driver block power supply uses the on-chip switching regulator, making this component an ideal choice for low-power sets.
Applications
Portable CD players
Features
1) Four H-bridge driver circuits.
2) DC to DC converter control circuit.
3) Reset circuit.
4) Shock detection circuit.
5) Battery recharge circuit.
Absolute maximum ratings (Ta = 25C)
Recommended operating conditions (Ta = 25C)
606
6)
7)
8)
9)
10)
Ripple filter circuit.
Audio reference output.
Low power consumption.
Thermal shutdown circuit.
QFP44 package.
Optical disc ICs
BA6893AK
Block diagram
607
Optical disc ICs
Pin descriptions
608
BA6893AK
Optical disc ICs
BA6893AK
Input / output circuits
609
Optical disc ICs
610
BA6893AK
Optical disc ICs
BA6893AK
611
Optical disc ICs
612
BA6893AK
Optical disc ICs
BA6893AK
613
Optical disc ICs
614
BA6893AK
Optical disc ICs
BA6893AK
615
Optical disc ICs
BA6893AK
Electrical characteristics (unless otherwise noted, Ta = 25C, BATT = 2.4V, VSYS1 = VSYS2 = 3.2V, VREF = 1.6V,
CHGVCC = 0V, and fCLK = 88.2kHz)
616
Optical disc ICs
BA6893AK
617
Optical disc ICs
618
BA6893AK
Optical disc ICs
BA6893AK
619
Optical disc ICs
FCircuit operation
(1) Empty detector block
When the voltage applied to the BSEN pin falls below the
detector voltage, EMP (pin 35) goes from high level to
low level (open-collector output). The detector voltage
has 50mV (Typ.) of hysteresis to prevent output chattering. Use SEL (pin 42) to switch the detection voltage as
shown below.
(2) Reset circuit block
At about 90% (Typ.) of the DC / DC comparator output
voltage, RESET (pin 3) goes from low level to high level,
and AMUTE (pin 34) goes from high level to low level.
The reset voltage has 50mV (Typ.) of hysteresis to prevent output chattering.
(3) Ripple filter circuit
By connecting an external PNP transistor, a voltage of
(VSYS1 0.24)V is supplied from AVCC (pin 14). Connect
a ripple bypass capacitor between CRIP (pin 11) and
GND.
BA6893AK
A thermal shutdown circuit is provided, and when the
chip temperature reaches 150_C (Typ.) the charging current is cut. The chip starts operating again at about
120_C (Typ.).
(6) DC / DC converter block
(1) Output voltage
A 3.2V (Typ.) voltage multiplier circuit can be constructed
using external components. This voltage can be varied
with the addition of an external resistor. The setting method is as follows.
R2 S R4
R1 S R3
R1R3
R2R4
VSYS1 = 1.20
(V)
R2 S R4
R2R4
(2) Short protect function
When the error amplifier output (pin 6) has switched to
the high-level state, SPRT (pin 8) is charged, and when
the voltage reaches 1.2V (Typ.), the SW (pin 5) switching
stops. The time until switching stops is set by the capacitor connected to SPRT (pin 8) according to the following
formula.
(4) Audio reference circuit block
One half of the AVCC voltage (pin 14) generated by the ripple filter circuit is output from AREF (pin 10). The output
impedance is 4.0kΩ (Typ.).
(5) Charging circuit block
The power supply for the charging circuit block is
CHGVCC (pin 41), and is independent from the other circuits. The resistance between RCHG (pin 33) and GND
sets the charging current. This current is drawn from
SEL.
620
VTH
t = CSPRT
(sec)
ISPRT
(VTH = 1.20V, ISPRT = 10µA)
(3) Soft start function
The soft start function operates when a capacitor is connected between DEAD (pin 4) and GND. Also, the maximum duty can be varied by connecting a resistor to pin
4.
t = CDEADR (sec)
(R = 65kΩ)
Optical disc ICs
(4) Power off function
When low-level is applied to OFF (pin 40), SPRT (pin 8)
is charged, and when the voltage reaches 1.2V (Typ.),
the SW (pin 5) switching stops. The time until switching
stops is set by the capacitor connected to SPRT (pin 8)
according to the following formula.
VTH
t = CSPRT
(sec)
IOFF
(VTH = 1.20V, IOFF = 20µA)
(5) Over voltage protection circuit
When the voltage applied to BSEN (pin 1) reaches 8.4V
(Typ.), SPRT (pin 8) is charged, and when the voltage
reaches 1.2V (Typ.), the SW (pin 5) switching stops. The
time until switching stops is set by the capacitor connected to SPRT (pin 8) according to the following formula.
VTH
t = CSPRT
(sec)
IHV
(VTH = 1.20V, IHV = 20µA)
(7) H-bridge driver block
(1) Gain setting
The driver input resistance is 11kΩ (Typ.) for channels 1,
3, and 4, and 7.5kΩ for channel 2. Set the gain according
to the following formula.
BA6893AK
The driver output stage power supply is HVCC (pin 36),
and the bridge circuit power supply is VSYS2 (pin 15).
Connect a bypass capacitor between these two power
supplies (approximately 0.1µF).
(2) Mute function
Of the four drivers, channel 1 has a brake function, and
the other channels have a mute function.
When BRAKE1 (pin 23) is set to high level, both channel
1 outputs go low level, and the circuit enters brake mode.
When MUTE2 (pin 21) is set to high level, the channel 2
output is muted.
When MUTE34 (pin 19) is set to high level, the channel
3 and 4 outputs are muted.
(3) VREF drop mute
When the voltage applied to VREF (pin 16) is 1.0V or less
(Typ.), the driver outputs are set to high impedance.
(4) Thermal shutdown
When the chip temperature reaches 150C (Typ.) the
output current is cut. The chip starts operating again at
about 120C (Typ.).
(8) PWM power supply drive block
This detects the maximum output level from among the
four channels, and supplies the load drive power supply
for the PWM.
The external components are a PNP transistor, coil,
Schottky diode, and capacitor.
R: Externally-connected input resistor
621
Optical disc ICs
Application example
622
BA6893AK
Optical disc ICs
BA6893AK
External dimensions (Units: mm)
623