LXO1 OSCILLATOR 10 kHz to 2.1 MHz Low Power Crystal Oscillator ™ DESCRIPTION The LXO1 oscillator has the highest accuracy, stability and lowest current of all STATEK oscillators. The design consists of a CMOS-compatible hybrid circuit, packaged in a hermetically-sealed metal DIP. Permanent, precision tuning of the oscillator is accomplished by laser trimming the crystal after it has been hermetically sealed in a ceramic package and connected to the oscillator circuit. This method of fine tuning allows for very tight calibration tolerance and eliminates the need for a trimming capacitor, a major source of long-term frequency drift. The specifications and characteristics of the LXO1 vary with frequency. The characteristics of the 32.768 kHz model are presented in this data sheet. Hz M 1.0 1 LX0 PACKAGE DIMENSIONS E F G FEATURES H Low power consumption I J Low aging A CMOS compatible Double hermetically sealed package PIN NO.1 PIN NO.7 D Full military testing available 5V operation standard 2.5V to 15V operation also available B C Optional Tri-State PIN NO.8 PIN NO.14 APPLICATIONS Industrial, Computer & Communications General purpose clock oscillator Data Logger DIM inches mm A 0.810 MAX. 20.57 MAX. B 0.510 MAX. 12.95 MAX. C 0.300 +_ 0.005 7.62 +_ 0.13 Remote sensor D 0.600 +_ 0.005 15.24 +_ 0.13 Liquid level sensing E 0.430 TYP. 10.92 TYP. Medical test and diagnostics F 0.240 MAX. 6.10 MAX. G 0.040 TYP. 1.02 TYP. H 0.150 MIN. 3.81 MIN. Military Portable field communication Military high speed modem Flight recorder + _ I 0.018 0.002 0.46 +_ 0.05 J 0.070 TYP. 1.78 TYP. * Position of bumps for reference only IS O STATEK CORPORATION 512 N. MAIN ST., ORANGE, CA 92868 714-639-7810 FAX: 714-997-1256 www.statek.com YS 90 01 TEM C ERT I F I C AT N IO S 10112- Rev D SPECIFICATIONS: LXO1 32.768 kHz ABSOLUTE MAXIMUM RATINGS Specifications are typical at 25OC unless otherwise noted. Specifications are subject to change without notice. Supply Voltage Storage Temperature Supply Voltage (VDD) Calibration Tolerance1 5V +_ 10% (standard) (2.5V to 15V also available) ELECTRICAL CHARACTERISTICS LXO-1 32.768 kHz All parameters are measured at ambient temperature with a 10MΩ and 10pF load at 5V. + _ 10 ppm (0.001%) 25 ppm (0.0025%) + _ 100 ppm (0.01%) + _ SYMBOL PARAMETER 2 Frequency Stability O O 0 C to +50 C + _ 25 ppm Typ. 40 ppm MAX. + _ 70 ppm Typ. + _ 100 ppm MAX. (0.0025%) (0.004%) (0.007%) (0.01%) + _ -20OC to+70OC Voltage Coefficient + _ Aging + _ Vibration Frequency Change vs. 10% Output Load Change Operating Temp. Range + _ 4.8 TYP. MAX. UNIT Output Voltage Hi 4.95 V VOL Output Voltage Lo 0.05 0.2 V tr Rise Time (10%-90%) 12 25 ns tf Fall Time (10%-90%) 12 25 ns 50 60 % µA µA Duty Cycle 40 Supply Current 1 ppm/year Typ. + _ 3 ppm/year MAX. 1000 g, 1 ms,1/2 sine + _ 3 ppm MAX. 10 g RMS, 10-2000 Hz + _ 3 ppm MAX. MIN. VOH SYM IDD 1 ppm/V Typ. + _ 3 ppm/V MAX. Shock -0.3V to 7V -55OC to +125OC VDD =5V 6.5 12 VDD =3V 5 10 PIN CONNECTIONS Pin Connection 1 1 ppm MAX. INH (Tri-State) or NC 7 Vss (Gnd) 8 Output 14 -10OC to +70OC (Commercial) -40OC to +85OC (Industrial) -55OC to +125OC (Military) VDD PACKAGING LXO1 -Tube Pack 1. Tighter tolerances available 2. Does not include calibration tolerance. Positive variations small compared to negative variations. OUTPUT WAVE FORM TYPICAL CURRENT CONSUMPTION CURRENT (uA) LXO1 32.768 kHz VDD VOH 8 90%* 7 6 10%* VOL 0 5 3 2 3 4 5 6 tr tf *Of VDD 7 V (Volts) DD HOW TO ORDER LXO1 CRYSTAL OSCILLATORS LXO1 S “S” if special or custom design. Blank if Std. T T = Tri-State Blank = Pin1 no connection 32.768K , Frequency K = kHz M = MHz 10 / + Calibration Tolerance @ 25OC (in ppm) + Temp. Range: C = -10OC to +70OC I = -40OC to +85OC M = -55OC to +125OC S = Customer Specified 10112 - Rev D IS O STATEK CORPORATION 512 N. MAIN ST., ORANGE, CA 92868 714-639-7810 FAX: 714-997-1256 www.statek.com YS 90 01 C ERT I F I C TEM AT N IO S Other calibration fill in ppm. Standard Calibration Tolerances for frequencies other than 32.768 kHz: 1) 100 ppm (0.01%) 2) 300 ppm (0.03%) 3) 1000 ppm (0.1%) I