HIGH TEMPERATURE OSCILLATORS High Temperature/High Shock CXOHT CXOMHT CXOXHT 320 kHz - 50 MHz 320 kHz - 50 MHz 1 MHz - 50 MHz DESCRIPTION An increasing number of applications require the use of hightemperature oscillators. For these applications, Statek offers the CXOHT, CXOMHT, and CXOXHT oscillators. These oscillators are designed to operate at temperatures up to 225ºC with high shock survivability. FEATURES PIN CONNECTIONS High temperature operation up to 225OC Excellent stability over temperature Fast start-up High shock resistance CMOS and TTL compatible Optional output enable/disable Low EMI emission Hermetically sealed ceramic package 1. 2. 3. 4. Enable/Disable (E or T) or No Connection (N) Ground Output VDD DIMENSIONS CXOHT CXOMHT CXOXHT MAXIMUM MAXIMUM MAXIMUM DIM inches mm inches mm inches mm A 0.405 10.29 0.263 6.68 0.136 3.40 B 0.190 4.83 0.204 5.18 0.107 2.70 C (SM1) 0.055 1.40 0.055 1.40 0.043 1.09 Downhole instrumentation C (SM3/SM5) 0.063 1.60 0.063 1.60 0.048 1.21 Rotary shaft sensors D 0.350 8.89 0.065 1.65 0.041 1.10 Underground boring tools E 0.135 3.43 0.070 1.78 0.031 0.85 F 0.060 1.52 APPLICATIONS Industrial PACKAGE DIMENSIONS CXOHT CXOMHT CXOXHT CXOMHT CXOXHT SUGGESTED LAND PATTERN CXOHT 10180 - Rev C STATEK CORPORATION 512 N. MAIN ST., ORANGE, CA 92868 714-639-7810 FAX: 714-997-1256 www.statek.com SPECIFICATIONS ABSOLUTE MAXIMUM RATINGS Specifications are typical at 25OC unless otherwise noted. Specifications are subject to change without notice. Tighter specifications available. Please contact factory. Supply Voltage VDD Storage Temperature Maximum Process Temperature Supply Voltage1, 2 3.3 V ± 10% 5.0 V ± 10% ± 50 ppm, or tighter as required ± 100 ppm for 25OC to 150OC ± 150 ppm for 25OC to 175OC ± 175 ppm for 25OC to 200OC ± 250 ppm for 25OC to 225OC ± 200 ppm for 25OC to 200OC ± 300 ppm for 25OC to 225OC 5.0 V 3.3 V 24 MHz 3.0 mA 8.0 mA 32 MHz 5.0 mA 10.0 mA 50 MHz 6.0 mA 14.0 mA Calibration Tolerance Frequency Stability Over Temperature Total Tolerance3 Supply Current (Typical) -0.5 V to 7.0 V -55OC to 125OC 260OC, 20 seconds ENABLE/DISABLE OPTIONS (E/T/N) Statek offers three enable/disable options: E, T, and N. Both the E-version and T-version have Tri-State outputs and differ in whether the oscillator continues to run internally when the output is put into the high Z state: it stops in the E-version and continues to run in the T-version. So, the Eversion offers very low current consumption when the oscillator is disabled and the T-version offers very fast output recovery when the oscillator is re-enabled. The N-version does not have PIN 1 connected internally and so has no enable/disable capability. The following table summarizes the three options. COMPARISON OF ENABLE/DISABLE OPTIONS E AND T Output Load (CMOS) Start-up Time Rise/Fall Time Duty Cycle* Aging, first year Aging Shock, survival4 15 pF 5 ms MAX 10 ns MAX 40% MIN, 60% MAX 5 ppm MAX at 25OC 100 ppm MAX at 200OC Std: 3,000 g, 0.3 ms, 1/2 sine HG: 10,000 g, 0.3 ms, 1/2 sine 5 Vibration, survival 20 g, 10-2,000 Hz swept sine Operating Temp Range -55OC up to 225OC E T When enabled (PIN 1 is high*) Output Freq. output Freq. output Oscillator Oscillates Oscillates Current consumption Normal Normal When disabled (PIN 1 is low) 1. All frequencies, voltages, temperature ranges and enable/disable options may not be available. Contact factory. 2. 225OC only available at 3.3V. 3. Total Tolerance = Calibration Tolerance + Frequency Stability over temperature. 4. For CXOHT and CXOMHT oscillators only. The specification for std. CXOXHT oscillators is 5,000 g and for CXOXHTHG it is 10,000 g. 5. Per MIL-STD-202G, Method 204D, Condition D. Random vibration testing available. Note: All parameters are measured at ambient temperature with a 10 MΩ, 15 pF load. *Tighter duty cycle available. Contact factory. Output High Z state High Z state Oscillator Stops Oscillates Current consumption Very low Lower than normal When re-enabled (PIN 1 changes from low to high) Output recovery Delayed Immediate * When PIN 1 is allowed to float, it is held high by an internal pull-up resistor. PACKAGING OPTIONS CXOHT, CXOMHT, CXOXHT - Tray Pack - 16 mm tape, 7” or 13” reels Per EIA 481 (see Tape and Reel data sheet # 10109) HOW TO ORDER CXOHT, CXOMHT and CXOXHT OSCILLATORS CXOMHT 4 S CXOHT CXOMHT CXOXHT Supply Voltage 4 = 3.3 V 5 = 5.0 V* “S” if special or custom design. Blank if Std. * 200OC Max. @ 5V E Enable/Disable Option E or T or N HG = High Shock otherwise leave blank. SM3 20.0M, / Terminations Blank = SM1 = Gold Plated SM5 = Solder Dipped (Lead Free) Frequency M = MHz K = kHz Calibration Tolerance @ 250C (in ppm) / Total Frequency Tolerance (in ppm) Calibration Tolerance @ 250C (in ppm) / H Temp. Range: H = 250C to 2000C S = Customer Specified Temp. Range Frequency Stability over Temp. Range (in ppm) OR 50 / 200 175 Frequency Stability over Temp. Range (in ppm) / / Total Frequency Tolerance (in ppm) H Temp. Range: H = 250C to 2000C S = Customer Specified Temp. Range STATEK CORPORATION 512 N. MAIN ST., ORANGE, CA 92868 714-639-7810 FAX: 714-997-1256 www.statek.com 10180 - Rev C