CXOMHG OSCILLATOR 300 kHz to 120 MHz High Shock, Low Profile, Miniature Surface Mount Crystal Oscillator ™ DESCRIPTION GM M 4.19 Intended for applications requiring shock survivability to 10,000 g (and higher), Statek’s surface-mount CXOMHG oscillators are high-shock versions of the CXOM oscillators. These oscillators consist of a Statek miniature quartz crystal and a CMOS/TTL compatible hybrid circuit in a low-profile ceramic package with an extremely small footprint. actual size side view FEATURES High shock resistance Designed for surface mount applications using infrared, vapor phase, or epoxy mount techniques PACKAGE DIMENSIONS Hermetically sealed ceramic package CMOS and TTL compatible D Low power consumption 2 Optional Output Enable/Disable with Tri-State A Low EMI emission TOP 3 BOTTOM 1 Full military testing available 4 D APPLICATIONS B Military & Aerospace E C Smart munitions Projectile electronics TYPICAL Industrial Engine control Down-hole drilling MAXIMUM DIM inches mm inches mm A 0.256 6.50 0.263 6.68 B 0.197 5.00 0.204 5.18 C (SM1) 0.051 1.30 0.055 1.40 C (SM3/SM5) SUGGESTED LAND PATTERN 0.055 1.40 0.063 1.60 D 0.055 1.40 0.065 1.65 E 0.060 1.52 0.070 1.78 0.070 (1.78) 0.067 (1.70) PIN CONNECTIONS 0.065 (1.65) 1. Enable/Disable (E or T) or not connected (N) 2. Ground 0.201 (5.11) 3. Output 0.136 (3.45) 4. VDD GRID PLACEMENT COURTYARD ■ ■ ■ 90 Änderungen vorbehalten / subject to change without notice ■ IS O ■ 10160 Rev A YS 01 TEM C ERT I F I C AT N IO Distribution: RSG Electronic Components GmbH Sprendlinger Landstr. 115 D-63069 Offenbach/Germany Tel. +49 69 984047-0 Fax +49 69 984047-77 [email protected] www.rsg-electronic.de S 0.137 (3.48) inches (mm) Pb SPECIFICATIONS ABSOLUTE MAXIMUM RATINGS O Specifications are typical at 25 C unless otherwise noted. Specifications are subject to change without notice. Tighter specifications available. Please contact factory. Supply Voltage1 Supply Voltage VDD -0.5V to 7.0V Storage Temperature -55OC to +125OC Maximum Process Temperature 260OC fo 20 seconds 5.0 V Calibration Tolerance2 + _ Frequency Stability Over Temperature3 + _ Supply Current (Typical) ENABLE/DISABLE OPTIONS (E/T/N) 100 ppm Output Load (CMOS)4 15 pF Start-up Time Rise/Fall Time 5 ms MAX 6 ns MAX Duty Cycle 40% MIN, 60% MAX Aging, first year Statek offers three enable/disable options: E, T, and N. Both the E-version and T-version have Tri-State outputs and differ in whether the oscillator continues to run internally when the output is put into the high Z state: it stops in the E-version and continues to run in the T-version. So, the E-version offers very low current consumption when the oscillator is disabled and the T-version offers very fast output recovery when the oscillator is re-enabled. The N-version does not have PIN 1 connected internally and so has no enable/disable capability. The following table compares the E and T versions. 50 ppm for Commercial + _ 100 ppm for Industrial + _ 100 ppm for Military 10 MHz 4 mA 24 MHz 8 mA 30 MHz 10 mA 40 MHz 12 mA 50 MHz 14 mA COMPARISON OF ENABLE/DISABLE OPTIONS E AND T 10 ppm MAX Shock, survival 10,000 g, 0.3 ms, 1/2 sine Vibration, survival6 20 g, 10-2,000 Hz swept sine 5 O E T When enabled (PIN 1 is high*) O Operating Temp Ranges -10 C to +70 C (Commercial) -40OC to +85OC (Industrial) -55OC to +125OC (Military) 1. Other voltages available. For 3.3 V, see CXO3MHG data sheet. For others, contact factory. 2. Other tolerances available. 3. Does not include calibration tolerance. Other tolerances available. 4. Higher CMOS loads and TTL loads available. Contact factory. 5. Higher shock version available. Contact factory for requirements above 10,000 g. 6. Per MIL-STD-202G, Method 204D, Condition D. Random vibration testing also available. Note: All parameters are measured at ambient temperature with a 10 MΩ, 15 pF load. Output Freq. output Freq. output Oscillator Oscillates Oscillates Current consumption Normal Normal Output High Z state High Z state Oscillator Stops Oscillates Current consumption Very low Lower than normal When disabled (PIN 1 is low) When re-enabled (PIN 1 changes from low to high) Output recovery PACKAGING OPTIONS Delayed Immediate * When PIN 1 is allowed to float, it is held high by an internal pull-up resistor. CXOMHG - Tray Pack - 16 mm tape, 7˝or 13˝ reels Per EIA 418 (see Tape and Reel data sheet 10109) HOW TO ORDER CXOMHG SURFACE MOUNT CRYSTAL OSCILLATORS S T SM3 32.0M , “S” if special or custom design. Blank if Std. Enable/Disable Option E, T, or N Terminations Blank = SM1 = Gold Plated SM3 = Solder Dipped SM5 = Solder Dipped (Lead Free) Frequency K = kHz M = MHz 100 / 100 I / Frequency Stability over Temp.Range (in ppm) Calibration Tolerance @ 250C (in ppm) Temp. Range: C = -10OC to +70OC I = -40OC to +85OC M = -55OC to +125OC S = Customer Specified OR / / 200 Total Frequency Tolerance (in ppm) ■ ■ Temp. Range: C = -10OC to +70OC I = -40OC to +85OC M = -55OC to +125OC S = Customer Specified 10160 Rev A YS ■ IS O 90 Änderungen vorbehalten / subject to change without notice ■ ■ I 01 TEM C ERT I F I C AT N IO Distribution: RSG Electronic Components GmbH Sprendlinger Landstr. 115 D-63069 Offenbach/Germany Tel. +49 69 984047-0 Fax +49 69 984047-77 [email protected] www.rsg-electronic.de / S CXOMHG Pb