16-Bit, 1 MSPS PulSAR ADC in MSOP/QFN AD7980 FEATURES APPLICATION DIAGRAM EXAMPLE 2.5V TO 5V 16-bit resolution with no missing codes Throughput: 1 MSPS Low power dissipation: 7.0 mW @ 1 MSPS, 70 μW @ 10 kSPS INL: ±0.6 LSB typical, ±1.25 LSB maximum SINAD: 91.25 dB @ 10 kHz THD: −110 dB @ 10 kHz Pseudo differential analog input range 0 V to VREF with VREF between 2.5 V to 5.5 V Any input range and easy to drive with the ADA4841 No pipeline delay Single-supply 2.5 V operation with 1.8 V/2.5 V/3 V/5 V logic interface Serial interface SPI-/QSPI™-/MICROWIRE™-/DSP-compatible Daisy-chain multiple ADCs and busy indicator 10-lead MSOP and 10-lead, 3 mm × 3 mm, QFN (LFCSP), same space as SOT-23 Wide operating temperature range: −40°C to +125°C 0 TO VREF IN+ IN– 2.5V REF VDD VIO SDI AD7980 SCK SDO GND 1.8V TO 5V 3- OR 4-WIRE INTERFACE (SPI, DAISY CHAIN, CS) 06392-001 CNV Figure 1. GENERAL DESCRIPTION The AD7980 is a 16-bit, successive approximation, analog-todigital converter (ADC) that operates from a single power supply, VDD. It contains a low power, high speed, 16-bit sampling ADC and a versatile serial interface port. On the CNV rising edge, it samples an analog input IN+ between 0 V to REF with respect to a ground sense IN−. The reference voltage, REF, is applied externally and can be set independent of the supply voltage, VDD. Its power scales linearly with throughput. APPLICATIONS Battery-powered equipment Communications ATE Data acquisitions Medical instruments The SPI-compatible serial interface also features the ability, using the SDI input, to daisy-chain several ADCs on a single, 3-wire bus and provides an optional busy indicator. It is compatible with 1.8 V, 2.5 V, 3 V, or 5 V logic, using the separate supply VIO. The AD7980 is housed in a 10-lead MSOP or a 10-lead QFN (LFCSP) with operation specified from −40°C to +125°C. Table 1. MSOP, QFN (LFCSP) 14-/16-/18-Bit PulSAR® ADC Type 18-Bit 100 kSPS 250 kSPS AD76911 400 kSPS to 500 kSPS AD76901 1000 kSPS AD79821 16-Bit AD7680 AD7683 AD7684 AD7940 AD76851 AD76871 AD7694 AD79421 AD76861 AD76881 AD76931 AD79461 AD79801 14-Bit 1 ADC Driver ADA4941 ADA4841 ADA4941 ADA4841 Pin-for-pin compatible. Rev. B Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 ©2007–2009 Analog Devices, Inc. All rights reserved. AD7980 TABLE OF CONTENTS Features .............................................................................................. 1 Driver Amplifier Choice ........................................................... 15 Applications ....................................................................................... 1 Voltage Reference Input ............................................................ 16 Application Diagram Example........................................................ 1 Power Supply............................................................................... 16 General Description ......................................................................... 1 Digital Interface .......................................................................... 16 Revision History ............................................................................... 2 CS Mode, 3-Wire, Without Busy Indicator ............................ 17 Specifications..................................................................................... 3 CS Mode 3-Wire with Busy Indicator ..................................... 18 Timing Specifications....................................................................... 5 CS Mode 4-Wire, Without Busy Indicator ............................. 19 Absolute Maximum Ratings............................................................ 6 CS Mode 4-Wire with Busy Indicator ..................................... 20 ESD Caution .................................................................................. 6 Chain Mode, Without Busy Indicator ..................................... 21 Pin Configurations and Function Descriptions ........................... 7 Chain Mode with Busy Indicator ............................................. 22 Terminology ...................................................................................... 8 Application Hints ........................................................................... 23 Typical Performance Characteristics ............................................. 9 Layout .......................................................................................... 23 Theory of Operation ...................................................................... 13 Evaluating the Performance of the AD7980............................... 23 Circuit Information .................................................................... 13 Outline Dimensions ....................................................................... 24 Converter Operation .................................................................. 13 Ordering Guide .......................................................................... 25 Typical Connection Diagram ................................................... 14 Analog Input ............................................................................... 15 REVISION HISTORY 6/09—Rev. A to Rev. B Changes to Table 5 ............................................................................ 6 Changes to Figure 25 ...................................................................... 13 Updated Outline Dimensions ....................................................... 24 Changes to Ordering Guide .......................................................... 25 9/08—Rev. 0 to Rev. A Delete QFN Endnote ..................................................... Throughout Changes to Ordering Guide .......................................................... 24 8/07—Revision 0: Initial Version Rev. B | Page 2 of 28 AD7980 SPECIFICATIONS VDD = 2.5 V, VIO = 2.3 V to 5.5 V, VREF = 5 V, TA = –40°C to +125°C, unless otherwise noted. Table 2. Parameter RESOLUTION ANALOG INPUT Voltage Range Absolute Input Voltage Analog Input CMRR Leakage Current @ 25°C Input Impedance ACCURACY No Missing Codes Differential Linearity Error Integral Linearity Error Transition Noise Gain Error, TMIN to TMAX2 Gain Error Temperature Drift Zero Error, TMIN to TMAX2 Zero Temperature Drift Power Supply Sensitivity THROUGHPUT Conversion Rate Transient Response AC ACCURACY Dynamic Range Oversampled Dynamic Range Signal-to-Noise Ratio, SNR Spurious-Free Dynamic Range, SFDR Total Harmonic Distortion, THD Signal-to-(Noise + Distortion), SINAD Conditions Min 16 IN+ − IN− IN+ IN− fIN = 100 kHz Acquisition phase 0 −0.1 −0.1 A Grade Typ Max VREF VREF + 0.1 +0.1 Min 16 0 −0.1 −0.1 60 1 See the Analog Input section 16 −1.0 REF = 5 V REF = 2.5 V REF = 5 V REF = 2.5 V REF = 5 V REF = 2.5 V −2.5 −1.0 VDD = 2.5 V 5% VIO ≥ 2.3 V up to 85°C, VIO ≥ 3.3 V above 85°C up to 125°C Full-scale step ±0.5 ±0.7 ±1.5 ±1.65 0.75 1.2 ±2 ±0.35 ±0.08 0.54 ±0.1 0 VREF = 5 V VREF = 2.5 V fO = 10 kSPS fIN = 10 kHz, VREF = 5 V fIN = 10 kHz, VREF = 2.5 V fIN = 10 kHz fIN = 10 kHz fIN = 10 kHz, VREF = 5 V fIN = 10 kHz, VREF = 2.5 V 1 B Grade Typ Max VREF VREF + 0.1 +0.1 60 1 See the Analog Input section +2.0 16 −0.9 +2.5 −1.25 +1.0 −0.5 1 0 ±0.4 ±0.55 ±0.6 ±0.65 0.6 1.0 ±2 ±0.35 ±0.08 0.54 ±0.1 290 91 86 110 90 85.5 −103.5 −101 90.5 86.0 90 +0.9 +1.25 +0.5 Rev. B | Page 3 of 28 V V V dB nA Bits LSB1 LSB1 LSB1 LSB1 LSB1 LSB1 LSB1 ppm/°C mV ppm/°C LSB1 1 MSPS 290 ns 92 87 111 91 86.5 −110 −114 91.5 87.0 LSB means least significant bit. With the 5 V input range, 1 LSB is 76.3 μV. See the Terminology section. These specifications include full temperature range variation, but not the error contribution from the external reference. 3 All specifications in dB are referred to a full-scale input FSR. Tested with an input signal at 0.5 dB below full scale, unless otherwise specified. 2 Unit Bits dB3 dB3 dB3 dB3 dB3 dB3 dB3 dB3 dB3 AD7980 VDD = 2.5 V, VIO = 2.3 V to 5.5 V, VREF = 5 V, TA = –40°C to +125°C, unless otherwise noted. Table 3. Parameter REFERENCE Voltage Range Load Current SAMPLING DYNAMICS −3 dB Input Bandwidth Aperture Delay DIGITAL INPUTS Logic Levels VIL VIH VIL VIH IIL IIH DIGITAL OUTPUTS Data Format Pipeline Delay Conditions VOL VOH POWER SUPPLIES VDD VIO VIO Range Standby Current1, 2 Power Dissipation ISINK = 500 μA ISOURCE = −500 μA Energy per Conversion TEMPERATURE RANGE3 Specified Performance Min Typ 2.4 Max Unit 5.1 1 MSPS, REF = 5 V 330 V μA VDD = 2.5 V 10 2.0 MHz ns VIO > 3V VIO > 3V VIO ≤ 3V VIO ≤ 3V –0.3 0.7 × VIO –0.3 0.9 × VIO −1 −1 Serial 16 bits straight binary Conversion results available immediately after completed conversion 0.4 VIO − 0.3 2.375 2.3 1.8 Specified performance VDD and VIO = 2.5 V, 25°C 10 kSPS throughput 1 MSPS throughput, B Grade 1 MSPS throughput, A Grade TMIN to TMAX 0.3 × VIO VIO + 0.3 0.1 × VIO VIO + 0.3 +1 +1 2.5 0.35 70 7.0 7.0 7.0 −40 1 With all digital inputs forced to VIO or GND as required. During the acquisition phase. 3 Contact sales for extended temperature range. 2 Rev. B | Page 4 of 28 2.625 5.5 5.5 9.0 10 +125 V V μA μA μA V V V V V nA μW mW mW nJ/sample °C AD7980 TIMING SPECIFICATIONS −40°C to +125°C, VDD = 2.37 V to 2.63 V, VIO = 3.3 V to 5.5 V, unless otherwise stated. See Figure 2 and Figure 3 for load conditions. Table 4. Parameter Conversion Time: CNV Rising Edge to Data Available Acquisition Time Time Between Conversions CNV Pulse Width (CS Mode) SCK Period (CS Mode) VIO Above 4.5 V VIO Above 3 V VIO Above 2.7 V VIO Above 2.3 V SCK Period (Chain Mode) VIO Above 4.5 V VIO Above 3 V VIO Above 2.7 V VIO Above 2.3 V SCK Low Time SCK High Time SCK Falling Edge to Data Remains Valid SCK Falling Edge to Data Valid Delay VIO Above 4.5 V VIO Above 3 V VIO Above 2.7 V VIO Above 2.3 V CNV or SDI Low to SDO D15 MSB Valid (CS Mode) VIO Above 3 V VIO Above 2.3 V CNV or SDI High or Last SCK Falling Edge to SDO High Impedance (CS Mode) SDI Valid Setup Time from CNV Rising Edge SDI Valid Hold Time from CNV Rising Edge (CS Mode) SDI Valid Hold Time from CNV Rising Edge (Chain Mode) SCK Valid Setup Time from CNV Rising Edge (Chain Mode) SCK Valid Hold Time from CNV Rising Edge (Chain Mode) SDI Valid Setup Time from SCK Falling Edge (Chain Mode) SDI Valid Hold Time from SCK Falling Edge (Chain Mode) SDI High to SDO High (Chain Mode with Busy Indicator) tSCKL tSCKH tHSDO tDSDO tDIS tSSDICNV tHSDICNV tHSDICNV tSSCKCNV tHSCKCNV tSSDISCK tHSDISCK tDSDOSDI ns ns ns ns 10 15 20 ns ns ns ns ns ns ns ns ns ns ns 5 2 0 5 5 2 3 15 Y% VIO1 tDELAY VIH2 VIL2 06513-002 9.5 11 12 14 tEN 1.4V IOH Unit ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns 11.5 13 14 16 4.5 4.5 3 tDELAY 500µA Max 710 tSCK X% VIO1 CL 20pF Typ 10.5 12 13 15 IOL TO SDO Min 500 290 1000 10 VIH2 VIL2 1FOR VIO ≤ 3.0V, X = 90 AND Y = 10; FOR VIO > 3.0V X = 70, AND Y = 30. 2MINIMUM V AND MAXIMUM V USED. SEE DIGITAL INPUTS IH IL SPECIFICATIONS IN TABLE 3. Figure 3. Voltage Levels for Timing Figure 2. Load Circuit for Digital Interface Timing Rev. B | Page 5 of 28 06392-003 500µA Symbol tCONV tACQ tCYC tCNVH tSCK AD7980 ABSOLUTE MAXIMUM RATINGS Table 5. Parameter Analog Inputs IN+,1 IN−1 to GND Supply Voltage REF, VIO to GND VDD to GND VDD to VIO Digital Inputs to GND Digital Outputs to GND Storage Temperature Range Junction Temperature θJA Thermal Impedance (10-Lead MSOP) θJC Thermal Impedance (10-Lead MSOP) Lead Temperature Vapor Phase (60 sec) Infrared (15 sec) 1 Rating −0.3 V to VREF + 0.3 V or ±130 mA −0.3 V to +6 V −0.3 V to +3 V +3 V to −6 V −0.3 V to VIO + 0.3 V −0.3 V to VIO + 0.3 V −65°C to +150°C 150°C 200°C/W Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ESD CAUTION 44°C/W 215°C 220°C See the Analog Input section. Rev. B | Page 6 of 28 AD7980 PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS 10 VIO REF 1 9 SDI VDD 2 8 SCK IN+ 3 7 SDO 6 CNV IN– 4 AD7980 TOP VIEW (Not to Scale) GND 5 IN– 4 06392-004 IN+ 3 GND 5 Figure 4. 10-Lead MSOP Pin Configuration 10 VIO AD7980 TOP VIEW (Not to Scale) 9 SDI 8 SCK 7 SDO 6 CNV 06392-005 REF 1 VDD 2 Figure 5. 10-Lead QFN (LFCSP) Pin Configuration Table 6. Pin Function Descriptions Pin No. 1 Mnemonic REF Type1 AI 2 3 VDD IN+ P AI 4 5 6 IN− GND CNV AI P DI 7 8 9 SDO SCK SDI DO DI DI 10 VIO P Description Reference Input Voltage. The REF range is from 2.4 V to 5.1 V. It is referred to the GND pin. This pin should be decoupled closely to the pin with a 10 μF capacitor. Power Supply. Analog Input. It is referred to IN−. The voltage range, for example, the difference between IN+ and IN−, is 0 V to VREF. Analog Input Ground Sense. To be connected to the analog ground plane or to a remote sense ground. Power Supply Ground. Convert Input. This input has multiple functions. On its leading edge, it initiates the conversions and selects the interface mode of the part, chain, or CS mode. In CS mode, it enables the SDO pin when low. In chain mode, the data should be read when CNV is high. Serial Data Output. The conversion result is output on this pin. It is synchronized to SCK. Serial Data Clock Input. When the part is selected, the conversion result is shifted out by this clock. Serial Data Input. This input provides multiple features. It selects the interface mode of the ADC as follows. Chain mode is selected if SDI is low during the CNV rising edge. In this mode, SDI is used as a data input to daisy-chain the conversion results of two or more ADCs onto a single SDO line. The digital data level on SDI is output on SDO with a delay of 16 SCK cycles. CS mode is selected if SDI is high during the CNV rising edge. In this mode, either SDI or CNV can enable the serial output signals when low; if SDI or CNV is low when the conversion is complete, the busy indicator feature is enabled. Input/Output Interface Digital Power. Nominally at the same supply as the host interface (1.8 V, 2.5 V, 3 V, or 5 V). 1 AI = analog input, DI = digital input, DO = digital output, and P = power. Rev. B | Page 7 of 28 AD7980 TERMINOLOGY Integral Nonlinearity Error (INL) INL refers to the deviation of each individual code from a line drawn from negative full scale through positive full scale. The point used as negative full scale occurs ½ LSB before the first code transition. Positive full scale is defined as a level 1½ LSB beyond the last code transition. The deviation is measured from the middle of each code to the true straight line (see Figure 26). Differential Nonlinearity Error (DNL) In an ideal ADC, code transitions are 1 LSB apart. DNL is the maximum deviation from this ideal value. It is often specified in terms of resolution for which no missing codes are guaranteed. Offset Error The first transition should occur at a level ½ LSB above analog ground (38.1 μV for the 0 V to 5 V range). The offset error is the deviation of the actual transition from that point. Gain Error The last transition (from 111 … 10 to 111 … 11) should occur for an analog voltage 1½ LSB below the nominal full scale (4.999886 V for the 0 V to 5 V range). The gain error is the deviation of the actual level of the last transition from the ideal level after the offset is adjusted out. Spurious-Free Dynamic Range (SFDR) SFDR is the difference, in decibels (dB), between the rms amplitude of the input signal and the peak spurious signal. Effective Resolution Effective resolution is calculated as Effective Resolution = log2(2N/RMS Input Noise) and is expressed in bits. Total Harmonic Distortion (THD) THD is the ratio of the rms sum of the first five harmonic components to the rms value of a full-scale input signal and is expressed in dB. Dynamic Range Dynamic range is the ratio of the rms value of the full scale to the total rms noise measured with the inputs shorted together. The value for dynamic range is expressed in dB. It is measured with a signal at −60 dBFS to include all noise sources and DNL artifacts. Signal-to-Noise Ratio (SNR) SNR is the ratio of the rms value of the actual input signal to the rms sum of all other spectral components below the Nyquist frequency, excluding harmonics and dc. The value for SNR is expressed in dB. Signal-to-(Noise + Distortion) Ratio (SINAD) SINAD is the ratio of the rms value of the actual input signal to the rms sum of all other spectral components below the Nyquist frequency, including harmonics but excluding dc. The value for SINAD is expressed in dB. Aperture Delay Aperture delay is the measure of the acquisition performance. It is the time between the rising edge of the CNV input and when the input signal is held for a conversion. Effective Number of Bits (ENOB) ENOB is a measurement of the resolution with a sine wave input. It is related to SINAD by the following formula ENOB = (SINADdB − 1.76)/6.02 and is expressed in bits. Noise-Free Code Resolution Noise-free code resolution is the number of bits beyond which it is impossible to distinctly resolve individual codes. It is calculated as Transient Response Transient response is the time required for the ADC to accurately acquire its input after a full-scale step function is applied. Noise-Free Code Resolution = log2(2N/Peak-to-Peak Noise) and is expressed in bits. Rev. B | Page 8 of 28 AD7980 TYPICAL PERFORMANCE CHARACTERISTICS VDD = 2.5 V, VREF = 5.0 V, VIO = 3.3 V, unless otherwise noted. 1.25 1.00 POSITIVE INL: +0.33 LSB NEGATIVE INL: –0.39 LSB 1.00 POSITIVE INL: +0.18 LSB NEGATIVE INL: –0.21 LSB 0.75 0.75 0.50 0.25 DNL (LSB) INL (LSB) 0.50 0 –0.25 0.25 0 –0.25 –0.50 –0.50 –0.75 0 16384 32768 49152 –1.00 65536 06392-039 –1.25 –0.75 06392-036 –1.00 0 16384 32768 CODE Figure 6. Integral Nonlinearity vs. Code, REF = 5 V 1.25 65536 Figure 9. Differential Nonlinearity vs. Code, REF = 5 V 1.00 POSITIVE INL: +0.47 LSB NEGATIVE INL: –0.26 LSB 1.00 49152 CODE POSITIVE INL: +0.25 LSB NEGATIVE INL: –0.22 LSB 0.75 0.75 0.50 0.25 DNL (LSB) INL (LSB) 0.50 0 –0.25 0.25 0 –0.25 –0.50 –0.50 –0.75 0 16384 32768 49152 –1.00 65536 06392-061 –1.25 –0.75 06392-060 –1.00 0 16384 32768 CODE Figure 7. Integral Nonlinearity vs. Code, REF = 2.5 V –20 0 –60 AMPLITUDE (dB of FULL SCALE) SNR = 91.27dB THD = –114.63dB SFDR = 110.10dB SINAD = 91.25dB –40 –80 –100 –120 –140 –160 100 200 300 400 fS = 1 MSPS fIN = 10kHz –20 06392-038 AMPLITUDE (dB of FULL SCALE) Figure 10. Differential Nonlinearity vs. Code, REF = 2.5 V fS = 1 MSPS fIN = 10kHz 0 65536 500 FREQUENCY (kHz) SNR = 86.8dB THD = –111.4dB SFDR = 105.9dB SINAD = 86.8dB –40 –60 –80 –100 –120 –140 –160 –180 06392-058 0 –180 49152 CODE 0 100 200 300 FREQUENCY (kHz) Figure 8. FFT Plot, REF = 5 V Figure 11. FFT Plot, REF = 2.5 V Rev. B | Page 9 of 28 400 500 AD7980 180k 60k 168591 52212 160k 50k 140k 40k COUNTS 100k 80k 60k 32417 20k 52710 38751 40k 10k 0 27 0 1201 829 33 2 0 0 06392-042 20k 0 31340 30k 0 7225 0 0 8003 8004 8005 8006 8007 8008 8009 800A 800B 800C 800D 800E 800F 0 6807 539 16 502 14 0 06392-059 COUNTS 120k 0 7FFA 7FFB 7FFC 7FFD 7FFE 7FFF 8000 8001 8002 8003 8004 8005 8006 CODE IN HEX CODE IN HEX Figure 15. Histogram of a DC Input at the Code Center, REF = 2.5 V Figure 12. Histogram of a DC Input at the Code Center, REF = 5 V 95 70k 94 59691 59404 60k 93 92 40k SNR (dB) COUNTS 50k 30k 91 90 89 88 20k 0 2 150 93 06392-043 0 6295 5428 0 3 06392-046 87 10k 86 85 –10 7FFF 8000 8001 8002 8003 8004 8005 8006 8007 8008 –9 –7 –6 –5 –4 –3 –2 –1 0 Figure 16. SNR vs. Input Level Figure 13. Histogram of a DC Input at the Code Transition, REF = 5 V 100 115 –95 16 SNR SINAD ENOB –100 110 SFDR 85 13 105 –110 100 –115 95 THD 90 2.75 3.25 3.75 4.25 4.75 12 5.25 06392-044 –120 80 2.25 –125 2.25 2.75 3.25 3.75 4.25 4.75 REFERENCE VOLTAGE (V) REFERENCE VOLTAGE (V) Figure 14. SNR, SINAD, and ENOB vs. Reference Voltage Figure 17. THD, SFDR vs. Reference Voltage Rev. B | Page 10 of 28 SFDR (dB) 14 –105 85 5.25 06392-047 90 THD (dB) 15 ENOB (BITS) 95 SNR, SINAD (dB) –8 INPUT LEVEL (dB OF FULL SCALE) CODE IN HEX AD7980 100 –85 –90 –95 –100 THD (dB) 90 –105 –110 –115 85 06392-063 –120 80 10 –125 10 1000 100 06392-064 SINAD (dB) 95 FREQUENCY (kHz) Figure 21. THD vs. Frequency 95 –110 93 –112 91 –114 THD (dB) 89 –116 87 06392-049 –118 –35 –15 5 25 45 65 85 105 –120 –55 125 06392-052 SNR (dB) Figure 18. SINAD vs. Frequency 85 –55 –35 –15 TEMPERATURE (°C) 85 105 125 85 105 125 1.4 1.4 IVDD IVDD 1.2 1.0 1.0 CURRENT (mA) 1.2 0.8 0.6 IREF 0.8 0.6 IREF 0.4 0.4 IVIO IVIO 2.425 2.475 2.525 VDD VOLTAGE (V) 2.575 0 –55 2.625 06392-053 0.2 0.2 06392-050 CURRENT (mA) 5 25 45 65 TEMPERATURE (°C) Figure 22. THD vs. Temperature Figure 19. SNR vs. Temperature 0 2.375 1000 100 FREQUENCY (kHz) –35 –15 5 25 45 65 TEMPERATURE (°C) Figure 23. Operating Currents vs. Temperature Figure 20. Operating Currents vs. Supply Rev. B | Page 11 of 28 AD7980 8 7 5 4 3 IVDD + IVIO 2 1 0 –55 06392-054 CURRENT (µA) 6 –35 –15 5 25 45 65 TEMPERATURE (°C) 85 105 125 Figure 24. Power-Down Currents vs. Temperature Rev. B | Page 12 of 28 AD7980 THEORY OF OPERATION IN+ MSB LSB 32,768C 16,384C 4C 2C C SWITCHES CONTROL SW+ C BUSY REF COMP GND 32,768C 16,384C 4C 2C C CONTROL LOGIC OUTPUT CODE C LSB SW+ CNV 06392-011 MSB IN– Figure 25. ADC Simplified Schematic CIRCUIT INFORMATION The AD7980 is a fast, low power, single-supply, precise 16-bit ADC that uses a successive approximation architecture. The AD7980 is capable of converting 1,000,000 samples per second (1 MSPS) and powers down between conversions. When operating at 10 kSPS, for example, it consumes 70 μW typically, ideal for battery-powered applications. The AD7980 provides the user with on-chip track-and-hold and does not exhibit any pipeline delay or latency, making it ideal for multiple multiplexed channel applications. The AD7980 can be interfaced to any 1.8 V to 5 V digital logic family. It is housed in a 10-lead MSOP or a tiny 10-lead QFN (LFCSP) that combines space savings and allows flexible configurations. It is pin-for-pin compatible with the 18-bit AD7982. CONVERTER OPERATION The AD7980 is a successive approximation ADC based on a charge redistribution DAC. Figure 25 shows the simplified schematic of the ADC. The capacitive DAC consists of two identical arrays of 16 binary weighted capacitors, which are connected to the two comparator inputs. During the acquisition phase, terminals of the array tied to the comparator’s input are connected to GND via SW+ and SW−. All independent switches are connected to the analog inputs. Therefore, the capacitor arrays are used as sampling capacitors and acquire the analog signal on the IN+ and IN− inputs. When the acquisition phase is completed and the CNV input goes high, a conversion phase is initiated. When the conversion phase begins, SW+ and SW− are opened first. The two capacitor arrays are then disconnected from the inputs and connected to the GND input. Therefore, the differential voltage between the inputs IN+ and IN− captured at the end of the acquisition phase are applied to the comparator inputs, causing the comparator to become unbalanced. By switching each element of the capacitor array between GND and REF, the comparator input varies by binary weighted voltage steps (VREF/2, VREF/4 … VREF/65,536). The control logic toggles these switches, starting with the MSB, to bring the comparator back into a balanced condition. After the completion of this process, the part returns to the acquisition phase and the control logic generates the ADC output code and a busy signal indicator. Because the AD7980 has an on-board conversion clock, the serial clock, SCK, is not required for the conversion process. Rev. B | Page 13 of 28 AD7980 Transfer Functions Table 7. Output Codes and Ideal Input Voltages The ideal transfer characteristic for the AD7980 is shown in Figure 26 and Table 7. Description VREF = 5 V FSR – 1 LSB Midscale + 1 LSB Midscale Midscale – 1 LSB –FSR + 1 LSB –FSR 4.999924 V 2.500076 V 2.5 V 2.499924 V 76.3 μV 0V 111 ... 110 111 ... 101 1 2 TYPICAL CONNECTION DIAGRAM 000 ... 010 Figure 27 shows an example of the recommended connection diagram for the AD7980 when multiple supplies are available. 000 ... 001 –FSR –FSR + 1LSB –FSR + 0.5LSB +FSR – 1 LSB +FSR – 1.5 LSB ANALOG INPUT Figure 26. ADC Ideal Transfer Function REF1 V+ 2.5V 10µF2 100nF V+ 1.8V TO 5V 100nF 20Ω 0 TO VREF REF 2.7nF V– VDD IN+ VIO SDI SCK AD7980 4 IN– GND 3- OR 4-WIRE INTERFACE SDO CNV 06392-013 000 ... 000 This is also the code for an overranged analog input (VIN+ − VIN− above VREF − VGND). This is also the code for an underranged analog input (VIN+ − VIN− below VGND). 06392-012 ADC CODE (STRAIGHT BINARY) 111 ... 111 Analog Input Digital Output Code (Hexa) FFFF1 8001 8000 7FFF 0001 00002 1SEE THE VOLTAGE REFERENCE INPUT SECTION FOR REFERENCE SELECTION. 2C REF IS USUALLY A 10µF CERAMIC CAPACITOR (X5R). 3SEE THE DRIVER AMPLIFIER CHOICE SECTION. 4OPTIONAL FILTER. SEE THE ANALOG INPUT SECTION. 5SEE THE DIGITAL INTERFACE FOR THE MOST CONVENIENT INTERFACE MODE. Figure 27. Typical Application Diagram with Multiple Supplies Rev. B | Page 14 of 28 AD7980 ANALOG INPUT DRIVER AMPLIFIER CHOICE Figure 28 shows an equivalent circuit of the input structure of the AD7980. Although the AD7980 is easy to drive, the driver amplifier needs to meet the following requirements: The two diodes, D1 and D2, provide ESD protection for the analog inputs, IN+ and IN−. Care must be taken to ensure that the analog input signal never exceeds the supply rails by more than 0.3 V, because this causes these diodes to become forwardbiased and start conducting current. These diodes can handle a forward-biased current of 130 mA maximum. For instance, these conditions could eventually occur when the input buffer’s (U1) supplies are different from VDD. In such a case (for example, an input buffer with a short circuit), the current limitation can be used to protect the part. The noise generated by the driver amplifier needs to be kept as low as possible to preserve the SNR and transition noise performance of the AD7980. The noise coming from the driver is filtered by the AD7980 analog input circuit’s 1-pole, low-pass filter made by RIN and CIN or by the external filter, if one is used. Because the typical noise of the AD7980 is 47.3 μV rms, the SNR degradation due to the amplifier is SNRLOSS REF D1 IN+ OR IN– CIN D2 GND Figure 28. Equivalent Analog Input Circuit The analog input structure allows the sampling of the true differential signal between IN+ and IN−. By using these differential inputs, signals common to both inputs are rejected. During the acquisition phase, the impedance of the analog inputs (IN+ and IN−) can be modeled as a parallel combination of capacitor, CPIN, and the network formed by the series connection of RIN and CIN. CPIN is primarily the pin capacitance. RIN is typically 400 Ω and is a lumped component made up of some serial resistors and the on resistance of the switches. CIN is typically 30 pF and is mainly the ADC sampling capacitor. During the conversion phase, where the switches are opened, the input impedance is limited to CPIN. RIN and CIN make a 1-pole, low-pass filter that reduces undesirable aliasing effects and limits the noise. When the source impedance of the driving circuit is low, the AD7980 can be driven directly. Large source impedances significantly affect the ac performance, especially THD. The dc performances are less sensitive to the input impedance. The maximum source impedance depends on the amount of THD that can be tolerated. The THD degrades as a function of the source impedance and the maximum input frequency. where: f–3dB is the input bandwidth in MHz of the AD7980 (10 MHz) or the cutoff frequency of the input filter, if one is used. N is the noise gain of the amplifier (for example, 1 in buffer configuration). eN is the equivalent input noise voltage of the op amp, in nV/√Hz. 06392-014 CPIN RIN 47.3 20 log π 2 2 47.3 f 3dB (Ne N ) 2 For ac applications, the driver should have a THD performance commensurate with the AD7980. For multichannel multiplexed applications, the driver amplifier and the AD7980 analog input circuit must settle for a full-scale step onto the capacitor array at a 16-bit level (0.0015%, 15 ppm). In the amplifier’s data sheet, settling at 0.1% to 0.01% is more commonly specified. This could differ significantly from the settling time at a 16-bit level and should be verified prior to driver selection. Table 8. Recommended Driver Amplifiers Amplifier ADA4841 AD8021 AD8022 OP184 AD8655 AD8605, AD8615 Rev. B | Page 15 of 28 Typical Application Very low noise, small and low power Very low noise and high frequency Low noise and high frequency Low power, low noise, and low frequency 5 V single-supply, low noise 5 V single-supply, low power AD7980 10.000 When REF is driven by a very low impedance source, for example, a reference buffer using the AD8031 or the AD8605, a ceramic chip capacitor is appropriate for optimum performance. If an unbuffered reference voltage is used, the decoupling value depends on the reference used. For instance, a 22 μF (X5R, 1206 size) ceramic chip capacitor is appropriate for optimum performance using a low temperature drift ADR43x reference. If desired, a reference-decoupling capacitor value as small as 2.2 μF can be used with a minimal impact on performance, especially DNL. IREF 0.100 IVIO 0.010 0.001 10000 100000 SAMPLING RATE (SPS) 1000000 DIGITAL INTERFACE POWER SUPPLY The AD7980 uses two power supply pins: a core supply, VDD, and a digital input/output interface supply, VIO. VIO allows direct interface with any logic between 1.8 V and 5.0 V. To reduce the number of supplies needed, VIO and VDD can be tied together. The AD7980 is independent of power supply sequencing between VIO and VDD. Additionally, it is very insensitive to power supply variations over a wide frequency range, as shown in Figure 29. Though the AD7980 has a reduced number of pins, it offers flexibility in its serial interface modes. The AD7980, when in CS mode, is compatible with SPI, QSPI, and digital hosts. This interface can use either a 3-wire or 4-wire interface. A 3-wire interface using the CNV, SCK, and SDO signals minimizes wiring connections useful, for instance, in isolated applications. A 4-wire interface using the SDI, CNV, SCK, and SDO signals allows CNV, which initiates the conversions, to be independent of the readback timing (SDI). This is useful in low jitter sampling or simultaneous sampling applications. The AD7980, when in chain mode, provides a daisy-chain feature using the SDI input for cascading multiple ADCs on a single data line similar to a shift register. 80 75 PSRR (dB) IVDD Figure 30. Operating Currents vs. Sampling Rate Regardless, there is no need for an additional lower value ceramic decoupling capacitor (for example, 100 nF) between the REF and GND pins. The mode in which the part operates depends on the SDI level when the CNV rising edge occurs. The CS mode is selected if SDI is high, and the chain mode is selected if SDI is low. The SDI hold time is such that when SDI and CNV are connected together, the chain mode is selected. 70 65 In either mode, the AD7980 offers the flexibility to optionally force a start bit in front of the data bits. This start bit can be used as a busy signal indicator to interrupt the digital host and trigger the data reading. Otherwise, without a busy indicator, the user must time out the maximum conversion time prior to readback. 06392-062 60 55 1.000 06392-055 The AD7980 voltage reference input, REF, has a dynamic input impedance and should therefore be driven by a low impedance source with efficient decoupling between the REF and GND pins, as explained in the Layout section. OPERATING CURRENTS (mA) VOLTAGE REFERENCE INPUT 1 10 100 1000 FREQUENCY (kHz) Figure 29. PSRR vs. Frequency The busy indicator feature is enabled To ensure optimum performance, VDD should be roughly half of REF, the voltage reference input. For example, if REF is 5.0 V, VDD should be set to 2.5 V (±5%). The AD7980 powers down automatically at the end of each conversion phase and, therefore, the power scales linearly with the sampling rate. This makes the part ideal for low sampling rate (even of a few Hz) and low battery-powered applications. In the CS mode if CNV or SDI is low when the ADC conversion ends (see Figure 34 and Figure 38). In the chain mode if SCK is high during the CNV rising edge (see Figure 42). Rev. B | Page 16 of 28 AD7980 When CNV goes low, the MSB is output onto SDO. The remaining data bits are then clocked by subsequent SCK falling edges. The data is valid on both SCK edges. Although the rising edge can be used to capture the data, a digital host using the SCK falling edge allows a faster reading rate provided that it has an acceptable hold time. After the 16th SCK falling edge or when CNV goes high, whichever is earlier, SDO returns to high impedance. CS MODE, 3-WIRE, WITHOUT BUSY INDICATOR This mode is usually used when a single AD7980 is connected to an SPI-compatible digital host. The connection diagram is shown in Figure 31, and the corresponding timing is given in Figure 32. With SDI tied to VIO, a rising edge on CNV initiates a conversion, selects the CS mode, and forces SDO to high impedance. Once a conversion is initiated, it continues until completion irrespective of the state of CNV. This can be useful, for instance, to bring CNV low to select other SPI devices, such as analog multiplexers; however, CNV must be returned high before the minimum conversion time elapses and then held high for the maximum conversion time to avoid the generation of the busy signal indicator. When the conversion is complete, the AD7980 enters the acquisition phase and powers down. CONVERT DIGITAL HOST CNV VIO AD7980 SDI SDO DATA IN 06392-015 SCK CLK Figure 31. 3-Wire CS Mode Without Busy Indicator Connection Diagram (SDI High) SDI=1 tCYC tCNVH CNV AQUISITION tCONV tACQ CONVERSION AQUISITION tSCK tSCKL 2 3 14 tHSDO 16 tSCKH tEN SDO 15 tDIS tDSDO D15 D14 D13 D1 D0 Figure 32. 3-Wire CS Mode Without Busy Indicator Serial Interface Timing (SDI High) Rev. B | Page 17 of 28 06392-016 1 SCK AD7980 If multiple AD7980s are selected at the same time, the SDO output pin handles this contention without damage or induced latch-up. Meanwhile, it is recommended to keep this contention as short as possible to limit extra power dissipation. CS MODE 3-WIRE WITH BUSY INDICATOR This mode is usually used when a single AD7980 is connected to an SPI-compatible digital host having an interrupt input. The connection diagram is shown in Figure 33, and the corresponding timing is given in Figure 34. CONVERT With SDI tied to VIO, a rising edge on CNV initiates a conversion, selects the CS mode, and forces SDO to high impedance. SDO is maintained in high impedance until the completion of the conversion irrespective of the state of CNV. Prior to the minimum conversion time, CNV can be used to select other SPI devices, such as analog multiplexers, but CNV must be returned low before the minimum conversion time elapses and then held low for the maximum conversion time to guarantee the generation of the busy signal indicator. When the conversion is complete, SDO goes from high impedance to low. With a pull-up on the SDO line, this transition can be used as an interrupt signal to initiate the data reading controlled by the digital host. The AD7980 then enters the acquisition phase and powers down. The data bits are clocked out, MSB first, by subsequent SCK falling edges. The data is valid on both SCK edges. Although the rising edge can be used to capture the data, a digital host using the SCK falling edge allows a faster reading rate provided it has an acceptable hold time. After the optional 17th SCK falling edge or when CNV goes high, whichever is earlier, SDO returns to high impedance. SDI = 1 VIO CNV VIO SDI AD7980 DIGITAL HOST 47kΩ SDO DATA IN SCK IRQ 06392-017 CLK Figure 33. 3-Wire CS Mode with Busy Indicator Connection Diagram (SDI High) tCYC tCNVH CNV AQUISITION tCONV tACQ CONVERSION AQUISITION tSCK tSCKL 1 2 3 15 tHSDO 16 17 tSCKH tDIS tDSDO SDO D15 D14 D1 D0 Figure 34. 3-Wire CS Mode with Busy Indicator Serial Interface Timing (SDI High) Rev. B | Page 18 of 28 06392-018 SCK AD7980 When the conversion is complete, the AD7980 enters the acquisition phase and powers down. Each ADC result can be read by bringing its SDI input low, which consequently outputs the MSB onto SDO. The remaining data bits are then clocked by subsequent SCK falling edges. The data is valid on both SCK edges. Although the rising edge can be used to capture the data, a digital host using the SCK falling edge allows a faster reading rate provided it has an acceptable hold time. After the 16th SCK falling edge or when SDI goes high, whichever is earlier, SDO returns to high impedance and another AD7980 can be read. CS MODE 4-WIRE, WITHOUT BUSY INDICATOR This mode is usually used when multiple AD7980s are connected to an SPI-compatible digital host. A connection diagram example using two AD7980s is shown in Figure 35, and the corresponding timing is given in Figure 36. With SDI high, a rising edge on CNV initiates a conversion, selects the CS mode, and forces SDO to high impedance. In this mode, CNV must be held high during the conversion phase and the subsequent data readback (if SDI and CNV are low, SDO is driven low). Prior to the minimum conversion time, SDI can be used to select other SPI devices, such as analog multiplexers, but SDI must be returned high before the minimum conversion time elapses and then held high for the maximum conversion time to avoid the generation of the busy signal indicator. CS2 CS1 CONVERT CNV SDI AD7980 CNV SDO SDI DIGITAL HOST AD7980 SCK SDO SCK 06392-019 DATA IN CLK Figure 35. 4-Wire CS Mode Without Busy Indicator Connection Diagram tCYC CNV AQUISITION tCONV tACQ CONVERSION AQUISITION tSSDICNV SDI(CS1) tHSDICNV SDI(CS2) tSCK tSCKL SCK 2 3 14 tHSDO SDO 15 16 17 18 30 31 32 tSCKH tEN tDIS tDSDO D15 D14 D13 D1 D0 D15 D14 Figure 36. 4-Wire CS Mode Without Busy Indicator Serial Interface Timing Rev. B | Page 19 of 28 D1 D0 06392-020 1 AD7980 With a pull-up on the SDO line, this transition can be used as an interrupt signal to initiate the data readback controlled by the digital host. The AD7980 then enters the acquisition phase and powers down. The data bits are clocked out, MSB first, by subsequent SCK falling edges. The data is valid on both SCK edges. Although the rising edge can be used to capture the data, a digital host using the SCK falling edge allows a faster reading rate provided it has an acceptable hold time. After the optional 17th SCK falling edge or SDI going high, whichever is earlier, the SDO returns to high impedance. CS MODE 4-WIRE WITH BUSY INDICATOR This mode is usually used when a single AD7980 is connected to an SPI-compatible digital host that has an interrupt input, and it is desired to keep CNV, which is used to sample the analog input, independent of the signal used to select the data reading. This requirement is particularly important in applications where low jitter on CNV is desired. The connection diagram is shown in Figure 37, and the corresponding timing is given in Figure 38. With SDI high, a rising edge on CNV initiates a conversion, selects the CS mode, and forces SDO to high impedance. In this mode, CNV must be held high during the conversion phase and the subsequent data readback (if SDI and CNV are low, SDO is driven low). Prior to the minimum conversion time, SDI can be used to select other SPI devices, such as analog multiplexers, but SDI must be returned low before the minimum conversion time elapses and then held low for the maximum conversion time to guarantee the generation of the busy signal indicator. When the conversion is complete, SDO goes from high impedance to low. CS1 CONVERT VIO CNV AD7980 SDO DATA IN SCK IRQ 06392-021 SDI DIGITAL HOST 47kΩ CLK Figure 37. 4-Wire CS Mode with Busy Indicator Connection Diagram tCYC CNV AQUISITION tCONV tACQ CONVERSION AQUISITION tSSDICNV SDI tSCK tHSDICNV tSCKL 2 3 15 tHSDO 16 17 tSCKH tDIS tDSDO tEN SDO D15 D14 D1 Figure 38. 4-Wire CS Mode with Busy Indicator Serial Interface Timing Rev. B | Page 20 of 28 D0 06392-022 1 SCK AD7980 When SDI and CNV are low, SDO is driven low. With SCK low, a rising edge on CNV initiates a conversion, selects the chain mode, and disables the Busy indicator. In this mode, CNV is held high during the conversion phase and the subsequent data readback. When the conversion is complete, the MSB is output onto SDO and the AD7980 enters the acquisition phase and powers down. The remaining data bits stored in the internal shift register are clocked by subsequent SCK falling edges. For each ADC, SDI feeds the input of the internal shift register and is clocked by the SCK falling edge. Each ADC in the chain outputs its data MSB first, and 16 × N clocks are required to readback the N ADCs. The data is valid on both SCK edges. Although the rising edge can be used to capture the data, a digital host using the SCK falling edge allows a faster reading rate and, consequently, more AD7980s in the chain, provided the digital host has an acceptable hold time. The maximum conversion rate may be reduced due to the total readback time. CHAIN MODE, WITHOUT BUSY INDICATOR This mode can be used to daisy-chain multiple AD7980s on a 3-wire serial interface. This feature is useful for reducing component count and wiring connections, for example, in isolated multi-converter applications or for systems with a limited interfacing capacity. Data readback is analogous to clocking a shift register. A connection diagram example using two AD7980s is shown in Figure 39, and the corresponding timing is given in Figure 40. CONVERT CNV SDI CNV AD7980 SDO SDI DIGITAL HOST AD7980 A SCK SDO DATA IN B SCK 06392-023 CLK Figure 39. Chain Mode Without Busy Indicator Connection Diagram SDIA = 0 tCYC CNV AQUISITION tCONV tACQ CONVERSION AQUISITION tSCK tSCKL tSSDICNV SCK 1 2 3 15 16 17 18 30 31 32 DA1 DA0 tSCKH tHSDISC tEN SDOA = SDIB 14 tSSDISCK tHSDICNV DA15 DA14 DA13 DA1 DA0 DB1 DB0 tDSDO SDOB DB15 DB14 DB13 DA15 DA14 Figure 40. Chain Mode Without Busy Indicator Serial Interface Timing Rev. B | Page 21 of 28 06392-024 tHSDO AD7980 When SDI and CNV are low, SDO is driven low. With SCK high, a rising edge on CNV initiates a conversion, selects the chain mode, and enables the busy indicator feature. In this mode, CNV is held high during the conversion phase and the subsequent data readback. When all ADCs in the chain have completed their conversions, the SDO pin of the ADC closest to the digital host (see the AD7980 ADC labeled C in Figure 41) is driven high. This transition on SDO can be used as a busy indicator to trigger the data readback controlled by the digital host. The AD7980 then enters the acquisition phase and powers down. The data bits stored in the internal shift register are clocked out, MSB first, by subsequent SCK falling edges. For each ADC, SDI feeds the input of the internal shift register and is clocked by the SCK falling edge. Each ADC in the chain outputs its data MSB first, and 16 × N + 1 clocks are required to readback the N ADCs. Although the rising edge can be used to capture the data, a digital host using the SCK falling edge allows a faster reading rate and, consequently, more AD7980s in the chain, provided the digital host has an acceptable hold time. CHAIN MODE WITH BUSY INDICATOR This mode can also be used to daisy-chain multiple AD7980s on a 3-wire serial interface while providing a busy indicator. This feature is useful for reducing component count and wiring connections, for example, in isolated multiconverter applications or for systems with a limited interfacing capacity. Data readback is analogous to clocking a shift register. A connection diagram example using three AD7980s is shown in Figure 41, and the corresponding timing is given in Figure 42. CONVERT AD7980 SDI CNV CNV SDO SDI AD7980 SDO DIGITAL HOST AD7980 SDI A B C SCK SCK SCK SDO DATA IN IRQ 06392-025 CNV CLK Figure 41. Chain Mode with Busy Indicator Connection Diagram tCYC CNV = SDIA tCONV tACQ AQUISITION CONVERSION AQUISITION tSCK tSCKH tSSDICNV 1 2 3 4 15 16 tSSDISCK tHSDICNV DA15 SDOA = SDIB DA14 DA13 18 19 31 32 33 34 35 tSCKL tHSDISC tEN 17 DA1 tDSDOSDI DB15 DB14 DB13 DB1 DB0 DA15 DA14 DA1 DA0 DC15 DC14 DC13 DC 1 DC0 DB15 DB14 DB1 DB0 tDSDOSDI SDOC 49 DA0 tDSDO SDOB = SDIC 48 tDSDOSDI tHSDO tDSDOSDI 47 tDSDODSI Figure 42. Chain Mode with Busy Indicator Serial Interface Timing Rev. B | Page 22 of 28 DA15 DA14 DA1 DA0 06392-026 SCK AD7980 APPLICATION HINTS LAYOUT The printed circuit board (PCB) that houses the AD7980 should be designed so that the analog and digital sections are separated and confined to certain areas of the board. The pinout of the AD7980, with all its analog signals on the left side and all its digital signals on the right side, eases this task. AD7980 At least one ground plane should be used. It can be common or split between the digital and analog section. In the latter case, the planes should be joined underneath the AD7980s. 06392-028 Avoid running digital lines under the device because these couple noise onto the die, unless a ground plane under the AD7980 is used as a shield. Fast switching signals, such as CNV or clocks, should never run near analog signal paths. Crossover of digital and analog signals should be avoided. Figure 43. Example Layout of the AD7980 (Top Layer) The AD7980 voltage reference input REF has a dynamic input impedance and should be decoupled with minimal parasitic inductances. This is done by placing the reference decoupling ceramic capacitor close to, ideally right up against, the REF and GND pins and connecting them with wide, low impedance traces. Finally, the power supplies VDD and VIO of the AD7980 should be decoupled with ceramic capacitors, typically 100 nF, placed close to the AD7980 and connected using short and wide traces to provide low impedance paths and reduce the effect of glitches on the power supply lines. EVALUATING THE PERFORMANCE OF THE AD7980 Other recommended layouts for the AD7980 are outlined in the documentation of the evaluation board for the AD7980 (EVAL-AD7980-CB). The evaluation board package includes a fully assembled and tested evaluation board, documentation, and software for controlling the board from a PC via the EVAL-CONTROL BRD3. Rev. B | Page 23 of 28 06392-027 An example of a layout following these rules is shown in Figure 43 and Figure 44. Figure 44. Example Layout of the AD7980 (Bottom Layer) AD7980 OUTLINE DIMENSIONS 3.10 3.00 2.90 6 10 3.10 3.00 2.90 1 5 5.15 4.90 4.65 PIN 1 0.50 BSC 0.95 0.85 0.75 0.15 0.05 1.10 MAX 0.33 0.17 SEATING PLANE 0.80 0.60 0.40 8° 0° 0.23 0.08 COPLANARITY 0.10 COMPLIANT TO JEDEC STANDARDS MO-187-BA Figure 45.10-Lead Mini Small Outline Package [MSOP] (RM-10) Dimensions shown in millimeters 0.30 0.23 0.18 3.00 BSC SQ 0.50 BSC 10 6 PIN 1 INDEX AREA 0.50 0.40 0.30 5 TOP VIEW SEATING PLANE 0.80 MAX 0.55 NOM 1 2.48 2.38 2.23 PIN 1 INDICATOR (R 0.20) 0.05 MAX 0.02 NOM 0.20 REF *PADDLE CONNECTED TO GND. THIS CONNECTION IS NOT REQUIRED TO MEET THE ELECTRICAL PERFORMANCES. Figure 46. 10-Lead Lead Frame Chip Scale Package [QFN (LFCSP_WD)] 3 mm × 3 mm Body, Very Very Thin, Dual Lead (CP-10-9) Dimensions shown in millimeters Contact sales for the non-RoHS compliant version of the part. Rev. B | Page 24 of 28 031208-B 0.80 0.75 0.70 1.74 1.64 1.49 *EXPOSED PAD (BOTTOM VIEW) AD7980 ORDERING GUIDE Model AD7980ARMZ1 AD7980ARMZRL71 AD7980BRMZ1 AD7980BRMZRL71 AD7980ACPZ-RL1 AD7980ACPZ-RL71 AD7980BCPZ-RL1 AD7980BCPZ-RL71 AD7980BCPZ-R21 EVAL-AD7980CBZ1, 2 EVAL-CONTROL BRD3 1 2 3 Integral Nonlinearity ±2.5 LSB max ±2.5 LSB max ±1.25 LSB max ±1.25 LSB max ±2.5 LSB max ±2.5 LSB max ±1.25 LSB max ±1.25 LSB max ±1.25 LSB max Temperature Range −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C Ordering Quantity Tube, 50 Reel, 1,000 Tube, 50 Reel, 1,000 Reel, 5,000 Reel, 1,000 Reel, 5,000 Reel, 1,000 Reel, 1,000 Package Description 10-Lead MSOP 10-Lead MSOP 10-Lead MSOP 10-Lead MSOP 10-Lead QFN (LFCSP_WD) 10-Lead QFN (LFCSP_WD) 10-Lead QFN (LFCSP_WD) 10-Lead QFN (LFCSP_WD) 10-Lead QFN (LFCSP_WD) Evaluation Board Controller Board Package Option RM-10 RM-10 RM-10 RM-10 CP-10-9 CP-10-9 CP-10-9 CP-10-9 CP-10-9 Z = RoHS Compliant Part. This board can be used as a standalone evaluation board or in conjunction with the EVAL-CONTROL BRD3 for evaluation/demonstration purposes. This board allows a PC to control and communicate with all Analog Devices evaluation boards ending in the CB designator. Rev. B | Page 25 of 28 Branding C5X C5X C5D C5D C5X C5X C5D C5D C5D AD7980 NOTES Rev. B | Page 26 of 28 AD7980 NOTES Rev. B | Page 27 of 28 AD7980 NOTES ©2007–2009 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D06392-0-6/09(B) Rev. B | Page 28 of 28