OPEN FRAME SOLENOIDS 1. Design and Features The open frame solenoid is the simplest form of construction of all the types of solenoids manufactured, and is shown in Fig. 1. Though the design is simple in construction, obtaining maximum performance requires the use of high permeable steel, and good quality manufacturing technology to assure the minimizing of air gaps in the metal frame assembly. Additionally, high quality coil winding techniques are used to maximize the number of coil windings that are housed in the allowable space. B) Return Spring The open frame solenoid does not include a return spring. Therefore, the application must include a return spring. C) Plunger and Shaft Modifications It is not recommended that customer modify the plunger or shaft, as the shafts are manufactured and plated at the factory. Any special configurations can be supplied. Please consult the factory for details. D) Installation of Solenoid The open frame solenoid uses tapped holes for mounting in the frame. Caution needs to be observed that the mounting screws used to attach these solenoids are the correct length so as not to damage the coil. 4. General Characteristics Insulation class Fig. 1 2. Stroke and Force The open frame solenoid is designed for long strokes. As such, the pole piece designs are conical to maximize performance over longer strokes. To improve efficiency, the solenoid stroke should be minimized in the application. Class A (105°C) Lead wire class A (105°C) Dielectric strength AC 1000V 50/60 Hz 1 min. (at normal temperature and normal humidity) Insulation resistance More than 100 Mohm at DC 500V megger (at normal temperature and normal humidity) Expected life 300,000 cycles (Solenoid cycle life is very dependent upon side load, frequency of use, and environmental conditions. Cycle life tests should be performed by the customer.) 3. Operational Considerations A) Temperature The coil data for the open frame solenoids shows the values at ambient temperature 20°C and with a standard heat sink. If a solenoid is used at a rating shown in the coil data, it is designed so that the coil temperature rises and reaches equilibrium at approximately 65°C. In applications where the ambient temperature is higher than 40°C, possible thermal damage can occur. Temperature rise tests should be performed by the customer to assure that the coil does not reach 105°C. Coils can be constructed to operate at temperatures higher than 105°C without thermal damage. Please consult the factory for details. 70 5. How to Select a Solenoid Before selecting an open frame solenoid, the following information must be determined : A) Force The actual force required in the application should be increased using a safety factor multiplier of 1.3 to arrive at the force value that should be used in your specification. B) Duty Cycle Use the aforementioned formula to calculate duty cycle. Also note the maximum on time. (See page2) C) Stroke Stroke is determined by application requirements. www.shindengen.co.jp/smt/ OPEN FRAME SOLENOIDS D) Operating Voltage Operating DC voltage is determined by the application and voltage available. After determining these specifications, one can find the correct size solerioid for the application, using the force-stroke characteristic tables and graphs. The coil data is also shown for different sizes of magnet wire. If the exact operating voltages is not in the coil data table, please consult the factory for details. To determine the force output of the solenoid after temperature rise, please use the amp-turn force graphs (page 100) after calculating the amp-turns. 6. Ordering Information #When ordering an open frame solenoid, the correct part number needs to be determined, from the catalog information, #Example of a complete part number : SK0520A06AA Open Frame Solenoids 7. Labeling For open frame solenoids the part number labeling is as follows : A) Standard Solenoid (no modifications). The solenoid label will have the part number and the date code (which identifies the year and week of manufacture). Example : SK0520A06AA 9405 Solenoid Size (Type No.) Date Code (year and week) B) Special Configuration (required for any modification to a standard design) Any change from the standard catalog design requires that a custom part number be assigned, which will also include the date code of manufacture. Example : M93020F 9405 Special Part Number Date Code (year and week) www.shindengen.co.jp/smt/ 71 SK0315A OPEN FRAME SOLENOID UNIT : mm SHOWN ENERGIZED AT20°C 3 AT20°C 1W 100％ 4 10W 10％ 0.5 4W 25％ 2W 50％ 0.1 0.05 WEIGHT : 5g PLUNGER: 1g RESPONSE TIME [N] FORCE [N] 1 0.5 1 STROKE [mm] 1.5 4W 25％ 2 10W 10％ 1 1W 100% 0 2W 50％ 50％ 3 0 2 0 STROKE-FORCE 0.5 1 STROKE [mm] 1.5 2 STROKE-RESPONSE TIME 17.5 2-M2 0.4 15±0.3 4±0.2 φ3±0.05 8±0.3 （4.5） （0.5） LEADS 240MIN. 10±0.3 (UL1571 AWG28) 5±0.2 7.5±0.5 （3） 14.5±0.5 φ1.2+0.3 1.6±0.2 0.5±0.2 FRAME THK. 1.0mm POSSIBLE EXTRUSION:LESS THAN 0.3mm COIL DATA without heat sink “on” time duty cycle= K100% “on” time + “off” time MAX. “on” time in seconds watts at 20˚C resistance Ω±10%(at 20˚C) 50% or less 25% or less ∞ 50 18 1.0 ampere-turns at 20˚C type no. 100% continuous 140 2.0 4.0 198 no. turns 10% or less 2 10.0 280 442 12 19 volts DC SK0315A06AA 36 920 6 SK0315A12AA 144 1750 12 17 24 38 SK0315A24AA 576 3370 24 34 48 76 SK0315A48AA 2304 6700 48 68 96 152 72 www.shindengen.co.jp/smt/ 8.5 SK0420F OPEN FRAME SOLENOID UNIT : mm SHOWN ENERGIZED AT20°C RESPONSE TIME [N] FORCE [N] 0.5 0.1 0.05 0.03 0.7W 100％ 32 1 WEIGHT : 8g PLUNGER: 2g AT20°C 40 3 0 1 2 3 4 STROKE [mm] 5 7W 10％ 2.8W 25％ 1.4W 50％ 0.7W 100％ 6 1.4W 50％ 24 2.8W 25％ 16 7W 10％ 8 0 0 STROKE-FORCE 1 2 3 4 STROKE [mm] 5 6 STROKE-RESPONSE TIME 20±0.3 LEADS 240MIN. （4） (UL1571 AWG28) φ4±0.05 2-M2 0.4 （0.7） 11±0.3 ±0.5 Open Frame Solenoids 3.5±0.2 7.5±0.3 24 ±0.2 12.3 7 （4.3） 19.7±0.3 φ1.6±0.2 0.7±0.2 1±0.2 FRAME THK. 1.0mm POSSIBLE EXTRUSION:LESS THAN 0.3mm COIL DATA without heat sink “on” time duty cycle= K100% “on” time + “off” time MAX. “on” time in seconds watts at 20˚C resistance Ω±10%(at 20˚C) 50% or less 25% or less ∞ 50 18 0.7 ampere-turns at 20˚C type no. 100% continuous 119 1.4 2.8 168 no. turns 10% or less 2 7.0 238 376 12 19 volts DC SK0420F06AA 51 1100 6 SK0420F12AA 205 2120 12 17 24 38 SK0420F24AA 823 4100 24 34 48 76 SK0420F48AA 3291 8100 48 68 96 152 www.shindengen.co.jp/smt/ 8.5 73 SK0520A OPEN FRAME SOLENOID UNIT : mm SHOWN ENERGIZED AT20°C 10 50％ 1 16W 10％ 0.5 6.4W 25％ 3.2W 50％ WEIGHT : 22g PLUNGER: 4g 0.1 0 1 2 3 4 STROKE [mm] 5 1.6W 100％ 20 RESPONSE TIME [N] FORCE [N] 5 AT20°C 24 16 3.2W 50％ 12 6.4W 25％ 8 16W 10％ 4 1.6W 100％ 6 0 0 STROKE-FORCE 1 2 3 4 STROKE [mm] 5 6 STROKE-RESPONSE TIME 30.5 4-M2.6 0.45 21±0.3 7±0.2 14±0.3 φ5±0.05 （6.5） φ2+0.1 0 （0.5） 17.8±0.3 LEADS 240MIN. ±0.2 2.5 (UL1007 AWG28) 13.5±0.5 （10.5） 8±0.2 20±0.5 FRAME THK. 1.2mm POSSIBLE EXTRUSION:LESS THAN 0.3mm COIL DATA without heat sink “on” time duty cycle= K100% “on” time + “off” time MAX. “on” time in seconds watts at 20˚C resistance Ω±10%(at 20˚C) 50% or less 25% or less ∞ 55 19 1.6 ampere-turns at 20˚C type no. 100% continuous 300 3.2 6.4 424 no. turns 10% or less 3 16.0 600 948 12 19 volts DC SK0520A06AA 23 1150 6 SK0520A12AA 90 2290 12 17 24 38 SK0520A24AA 360 4500 24 34 48 76 SK0520A48AA 1440 8600 48 68 96 152 74 www.shindengen.co.jp/smt/ 8.5 SK0626A OPEN FRAME SOLENOID UNIT : mm SHOWN ENERGIZED AT20°C 20 AT20°C 20 2.5W 100 10 RESPONSE TIME [N] 16 FORCE [N] 5 WEIGHT : 43g PLUNGER: 7g 25W 10％ 1 10W 25％ 0.5 5W 50％ 0.2 12 1 2 3 4 STROKE [mm] 5 10W 25％ 25W 10％ 8 4 2.5W 100 0 5W 50％ 0 6 STROKE-FORCE 0 1 2 3 4 STROKE [mm] 5 6 STROKE-RESPONSE TIME 38 2-M3 0.5 （0.6） 3±0.2 ±0.5 14 Open Frame Solenoids φ2+0.1 0 20±0.3 7±0.2 （5） φ6±0.05 16±0.3 26.8±0.3 ±0.2 16 LEADS 240MIN. (UL1007 AWG26) （12） 26±0.5 ±0.3 1.8±0.3 7 FRAME THK. 1.6mm POSSIBLE EXTRUSION:LESS THAN 0.5mm COIL DATA without heat sink “on” time duty cycle= K100% “on” time + “off” time MAX. “on” time in seconds watts at 20˚C resistance Ω±10%(at 20˚C) 50% or less 25% or less ∞ 100 36 2.5 ampere-turns at 20˚C type no. 100% continuous 428 5.0 10.0 605 no. turns 10% or less 7 25.0 856 1353 12 19 volts DC SK0626A06AA 14 1090 6 SK0626A12AA 58 2090 12 17 24 38 SK0626A24AA 230 4110 24 34 48 76 SK0626A48AA 922 8200 48 68 96 152 www.shindengen.co.jp/smt/ 8.5 75 SK0640C OPEN FRAME SOLENOID UNIT : mm SHOWN ENERGIZED AT20°C 20 RESPONSE TIME [N] 10 5 25W 10％ FORCE [N] WEIGHT : 48g PLUNGER: 9g AT20°C 24 10W 25％ 1 5W 50％ 0.5 2.5W 100 20 2.5W 100 16 5W 50％ 10W 25％ 25W 10％ 12 8 4 0.2 0 0 1 2 3 4 STROKE [mm] 5 6 0 STROKE-FORCE 1 2 3 4 STROKE [mm] 5 6 STROKE-RESPONSE TIME 50.5 2-M3 0.5 13.5±0.3 （10.5） 40±0.3 φ6±0.05 （9） φ3+0.1 0 （0.5） 3.5±0.2 20±0.3 20±0.2 12±0.2 18±0.5 LEADS 240MIN. (UL1007 AWG26) FRAME THK. 2.0mm POSSIBLE EXTRUSION:LESS THAN 1.0mm COIL DATA without heat sink “on” time duty cycle= K100% “on” time + “off” time MAX. “on” time in seconds watts at 20˚C resistance Ω±10%(at 20˚C) 50% or less 25% or less ∞ 100 36 2.5 ampere-turns at 20˚C type no. 100% continuous 504 5.0 10.0 712 no. turns 10% or less 7 25.0 1008 1593 12 19 volts DC SK0640C06AA 14 1185 6 SK0640C12AA 58 2480 12 17 24 38 SK0640C24AA 230 4830 24 34 48 76 SK0640C48AA 922 9460 48 68 96 152 76 www.shindengen.co.jp/smt/ 8.5 SK0730A OPEN FRAME SOLENOID UNIT : mm SHOWN ENERGIZED AT20°C 20 AT20°C 20 2.5W 100 10 RESPONSE TIME [N] 16 5 FORCE [N] 25W 10％ 10W 25％ 1 5W 50％ 0.5 0.2 0 1 2 5 3 4 STROKE [mm] 12 10W 25％ 8 25W 10％ 4 2.5W 100 WEIGHT : 48g PLUNGER: 8g 5W 50％ 0 6 STROKE-FORCE φ2+0.1 0 34.3±0.5 1 0 2 3 4 STROKE [mm] 5 6 STROKE-RESPONSE TIME 3-M2.6 0.45 30.3±0.3 2.5±0.2 20±0.3 10±0.2 Open Frame Solenoids φ16±0.3 5.5±0.1 φ7±0.05 （8） （0.5） +0.2 -0.5 12.8 LEADS 240MIN. (UL1007 AWG26) 11±0.2 （4.8） 29.5±0.5 FRAME THK. 1.6mm POSSIBLE EXTRUSION:LESS THAN 0.5mm COIL DATA without heat sink “on” time duty cycle= K100% “on” time + “off” time MAX. “on” time in seconds watts at 20˚C resistance Ω±10%(at 20˚C) 50% or less 25% or less ∞ 100 36 2.5 ampere-turns at 20˚C type no. 100% continuous 389 5.0 10.0 550 no. turns 10% or less 7 25.0 778 1230 12 19 volts DC SK0730C06AA 14 990 6 SK0730C12AA 58 1925 12 17 24 38 SK0730C24AA 230 3730 24 34 48 76 SK0730C48AA 922 7300 48 68 96 152 www.shindengen.co.jp/smt/ 8.5 77 SK0832A OPEN FRAME SOLENOID UNIT : mm SHOWN ENERGIZED AT20° 50 AT20° 20 3W 100 RESPONSE TIME [N] 16 FORCE [N] 10 12W 25％ 6W 50％ 3W 100 1 0.5 0 1 2 WEIGHT : 82g PLUNGER: 14g 3 4 STROKE [mm] 5 12W 25％ 12 30W 10％ 5 6W 50％ 30W 10％ 8 4 0 6 0 STROKE-FORCE 1 2 3 4 STROKE [mm] 5 6 STROKE-RESPONSE TIME 46 33±0.3 4-M3 0.5 （7） 15 22±0.3 ±0.2 φ8±0.05 φ3 φ3+0.1 0 26 （0.9） ±0.3 5±0.2 16±0.5 （14） 18±0.2 LEADS 240MIN. (UL1007 AWG26) 32±0.5 ±0.3 2±0.3 10 FRAME THK. 1.6mm POSSIBLE EXTRUSION:LESS THAN 0.5mm COIL DATA without heat sink “on” time duty cycle= K100% “on” time + “off” time MAX. “on” time in seconds watts at 20˚C resistance Ω±10%(at 20˚C) 50% or less 25% or less ∞ 100 36 3.0 ampere-turns at 20˚C type no. 100% continuous 571 6.0 12.0 807 no. turns 10% or less 7 30.0 1142 1805 12 19 volts DC SK0832A06AA 12 1150 6 SK0832A12AA 46 2300 12 17 24 38 SK0832A24AA 186 4430 24 34 48 76 SK0832A48AA 743 8410 48 68 96 152 78 www.shindengen.co.jp/smt/ 8.5 SK0836W OPEN FRAME SOLENOID UNIT : mm SHOWN ENERGIZED AT20°C 50 AT20°C 20 4W 100 FORCE [N] 10 RESPONSE TIME [N] 16 40W 10％ 5 12 16W 25％ 8W 50％ WEIGHT : 100g PLUNGER: 14g 0.5 0 1 2 3 4 STROKE [mm] 5 16W 25％ 40W 10％ 8 4 4W 100 1 8W 50％ 0 6 STROKE-FORCE 0 1 2 3 4 STROKE [mm] 5 6 STROKE-RESPONSE TIME 46.5 4-M3 0.5 37±0.3 20±0.3 8±0.2 8±0.05 （10） Open Frame Solenoids φ3+0.1 0 26±0.3 （0.5） 4±0.2 ±0.5 12.5 （10.5） ±0.2 20 LEADS 240MIN. (UL1007 AWG26) 36±0.5 ±0.3 2.2±0.3 8 FRAME THK. 2.0mm POSSIBLE EXTRUSION:LESS THAN 0.5mm COIL DATA without heat sink “on” time duty cycle= K100% “on” time + “off” time MAX. “on” time in seconds watts at 20˚C resistance Ω±10%(at 20˚C) 50% or less 25% or less ∞ 100 36 4.0 ampere-turns at 20˚C type no. 100% continuous 666 8.0 16.0 941 no. turns 10% or less 7 40.0 1332 2106 12 19 volts DC SK0836W06AA 9 1000 6 SK0836W12AA 36 2000 12 17 24 38 SK0836W24AA 144 4000 24 34 48 76 SK0836W48AA 576 7540 48 68 96 152 www.shindengen.co.jp/smt/ 8.5 79 SK0946A OPEN FRAME SOLENOID UNIT : mm SHOWN ENERGIZED AT20°C 50 AT20°C 24 3W 100 FORCE [N] 10 RESPONSE TIME [N] 20 30W 10％ 5 12W 25％ 6W 50％ WEIGHT : 96g PLUNGER: 20g 0.5 16 12W 25％ 12 30W 10％ 8 4 3W 100 1 6W 50％ 0 0 1 2 3 4 STROKE [mm] 5 0 6 STROKE-FORCE 1 2 3 4 STROKE [mm] 5 6 STROKE-RESPONSE TIME 56.5 4-M3 0.5 46.5±0.3 19±0.3 10±0.2 φ9±0.05 （8.5） 23±0.3 φ3+0.1 0 （0.5） ±0.2 16 4 ±0.5 LEADS 240MIN. ±0.2 28 (UL1007 AWG26) （11） 45.5±0.5 3±0.3 8±0.3 FRAME THK. 1.6mm POSSIBLE EXTRUSION:LESS THAN 0.8mm COIL DATA without heat sink “on” time duty cycle= K100% “on” time + “off” time MAX. “on” time in seconds watts at 20˚C resistance Ω±10%(at 20˚C) 50% or less 25% or less ∞ 100 36 3.0 ampere-turns at 20˚C type no. 100% continuous 585 6.0 12.0 827 no. turns 10% or less 7 30.0 1170 1849 12 19 volts DC SK0946A06AA 12 1120 6 SK0946A12AA 48 2320 12 17 24 38 SK0946A24AA 192 4680 24 34 48 76 SK0946A48AA 768 9000 48 68 96 152 80 www.shindengen.co.jp/smt/ 8.5 SK1040A OPEN FRAME SOLENOID UNIT : mm SHOWN ENERGIZED AT20°C 50 AT20°C 24 4.2W 100 RESPONSE TIME [N] FORCE [N] 20 42W 10％ 10 5 16.8W 25％ 8.4W 50％ 8.4W 50％ 16.8W 25％ 16 12 42W 10％ 8 4 4.2W 100 1 WEIGHT : 136g PLUNGER: 23g 0 1 2 3 4 STROKE [mm] 5 0 6 0 STROKE-FORCE 1 2 3 4 STROKE [mm] 5 6 STROKE-RESPONSE TIME 4-M3 0.5 50 40±0.3 19.4 24±0.3 ±0.2 φ10±0.05 （12） φ3+0.1 0 Open Frame Solenoids 29±0.3 （0.5） 3±0.2 17±0.5 LEADS 240MIN. 18±0.2 (UL1007 AWG26) （11） 39±0.5 3±0.3 8±0.3 FRAME THK. 2.0mm POSSIBLE EXTRUSION:LESS THAN 1.0mm COIL DATA without heat sink “on” time duty cycle= K100% “on” time + “off” time MAX. “on” time in seconds watts at 20˚C resistance Ω±10%(at 20˚C) 50% or less 25% or less ∞ 100 36 4.2 ampere-turns at 20˚C type no. 100% continuous 635 8.4 16.8 898 no. turns 10% or less 7 42.0 1270 2008 12 19 volts DC SK1040A06AA 9 1020 6 SK1040A12AA 34 2000 12 17 24 38 SK1040A24AA 137 3625 24 34 48 76 SK1040A48AA 549 7420 48 68 96 152 www.shindengen.co.jp/smt/ 8.5 81 SK1250W OPEN FRAME SOLENOID UNIT : mm SHOWN ENERGIZED AT20°C 50 60W 10％ RESPONSE TIME [N] FORCE [N] 30 24W 25％ 10 12W 50％ 8 AT20°C 24 6W 100 20 12W 50％ 16 24W 25％ 12 60W 10％ 8 6 4 6W 100 4 0 1 WEIGHT : 362g PLUNGER: 40g 2 3 4 STROKE [mm] 5 0 6 0 STROKE-FORCE 1 2 3 4 STROKE [mm] 5 6 STROKE-RESPONSE TIME 4-M4 0.7 59 50±0.3 0 φ3 +0.1 36±0.3 20±0.2 φ12±0.05 （8） 40±0.3 4±0.2 17±0.5 30±0.2 49±0.5 3.5±0.3 10 8±0.3 （0.5） LEADS 240MIN. (UL1007 AWG26) FRAME THK. 2.3mm POSSIBLE EXTRUSION:LESS THAN 1.0mm COIL DATA without heat sink “on” time duty cycle= K100% “on” time + “off” time MAX. “on” time in seconds watts at 20˚C resistance Ω±10%(at 20˚C) 50% or less 25% or less ∞ 140 50 6.0 ampere-turns at 20˚C type no. 100% continuous 1150 12.0 24.0 1626 no. turns 10% or less 9 60.0 2300 3636 12 19 volts DC SK1250W06AA 6 1100 6 SK1250W12AA 24 2370 12 17 24 38 SK1250W24AA 96 4600 24 34 48 76 SK1250W48AA 384 8640 48 68 96 152 82 www.shindengen.co.jp/smt/ 8.5 CHARACTERISTICS TABLES FOR OPEN FRAME AT20°C 70 50 50 10 10 SK0946A SK1040A SK0836W 1 SK0832A 0.5 SK1250W 5 SK1250W SK1040A SK0836W SK0946A SK0832A FORCE [N] FORCE [N] 5 AT20°C 70 1 SK0640C SK0730A SK0626A 0.5 SK0640C SK0730A SK0626A SK0520A SK0520A 0.1 SK0315A 0.1 SK0315A 0.03 SK0420F 0.05 SK0420F 0 1 2 3 4 STROKE [mm] 5 0.03 6 0 1 2 DUTY CYCLE100% 3 4 STROKE [mm] 5 6 DUTY CYCLE 50% AT20°C 70 AT20°C 70 50 50 SK1250W SK1250W 10 SK1040A SK0836W 10 SK0946A SK1040A SK0836W 5 SK0832A 5 SK0946A SK0730A SK0640C SK0730A SK0626A 1 0.5 SK0520A FORCE [N] FORCE [N] SK0832A SK0640C SK0626A 1 SK0520A SK0315A 0.5 SK0315A SK0420F 0.1 0.1 SK0420F 0.05 0.03 0.05 0 1 2 3 4 STROKE [mm] 5 6 0.03 0 1 DUTY CYCLE 25% 2 3 4 STROKE [mm] 5 6 DUTY CYCLE 10% www.shindengen.co.jp/smt/ 83 Open Frame Solenoids 0.05 OPEN FRAME SOLENOID AMPERE-TURN V.S. FORCE SK0520A 1 0.5 S 2 0.5 5 424 S 0.5 238 S 1 168 1 11 280 1 8 140 S 0.5 S 0.5 S 1 S 2 600 SK0420F 2 2 300 SK0315A PERFORMANCE CURVES ARE AT 20˚C S 1 S 3 S 4 0.1 FORCE[N] S 3 FORCE[N] FORCE[N] S 2 S 4 S 5 S 5 1 0.5 442 0.1 400 100 200 400 48 400 5 10 0.5 1 2 3 4 5 600 800 1000 AMPERE-T RNS SK0640C SK0730A S S S S S S 12 605 428 S S S S S S 504 SK0626A 11 10 300 AMPERE-T RNS 5 20 0.5 1 2 3 4 5 8 300 AMPERE-T RNS 0.1 0.06 200 550 200 0.02 38 0.02 100 0.05 3 6 0.05 S S S S S S 10 0.5 FORCE[N] 1 1 1008 0.5 1 15 3 FORCE[N] FORCE[N] 5 0.5 1 2 3 4 5 1200 0.1 1400 400 600 AMPERE-T RNS 800 0.5 0.5 0.3 400 0.3 800 1000 1200 1400 1600 1800 41 FORCE[N] 2106 500 1000 1500 S S S S S S 10 8 1500 AMPERE-T RNS 84 2000 2 1000 3636 2300 4 1626 2008 12 0 8 8 6 1000 S S S S S S 1500 2000 2500 800 1000 1200 1400 1600 1800 AMPERE-T RNS 30 FORCE[N] 5 500 0.3 400 600 2000 1150 635 10 0.5 1 2 3 4 5 1400 5 1 SK1250W S S S S S S 1200 0.5 SK1040A 50 1000 10 AMPERE-T RNS 50 0.5 0.5 1 2 3 4 5 5 AMPERE-T RNS FORCE[N] S S S S S S 1 1805 1 800 SK0946A 30 10 FORCE[N] FORCE[N] 0.5 1 2 3 4 5 666 1142 80 5 1 S S S S S S 5 1 600 AMPERE-T RNS SK0836W 30 10 600 400 AMPERE-T RNS SK0832A 30 0.2 200 1000 1200 1400 1600 184 1000 82 800 585 600 1332 400 11 0 1353 856 0.1 200 1230 0.5 3000 3500 AMPERE-T RNS www.shindengen.co.jp/smt/ 0.5 1 2 3 4 5 0.5 1 2 3 4 5