Data Sheets - Skyworks Solutions, Inc.

DATA SHEET
C0
Applications
 802.11a/b/g/n/ac WLANs
 Computing, networking
C1
SE5516A: Dual-Band 802.11a/b/g/n/ac WLAN Front-End
Module
Control, Decode
TG
Features
2G
LNA
RA
5G
LNA
SP3T
Switch
2G PA
Det
TA
ANT
2G Match
Filter
Diplexer
5G Filter
5G PA
ENG
DET
 Small LGA (24-pin, 4 x 4 mm) package (MSL3, 240 C per
JEDEC J-STD-020)
RG
ENA
 All RF ports matched to 50 Ω
 Integrated 2.4 GHz PA, 5 GHz PA, transmit filter,
transmit/receive switches, and diplexers
 Integrated power detector for each transmit chain
 Power:
 +21 dBm, 802.11b, 11 Mbps, ACPR = +35 dBc
 +18 dBm @ 3.0% EVM, 802.11n, 64 QAM, 2G
 +16 dBm @ 3.0% EVM, 802.11n, 64 QAM, 5G
 +16 dBm @ 1.8% EVM, 802.11ac, 256 QAM, 2G
 +13 dBm @ 1.8% EVM, 802.11ac, 256 QAM, 5G
 Single supply voltage: 3.3 V ± 10%
S2932
Figure 1. SE5516A Block Diagram
Skyworks Pb-free products are compliant with
all applicable legislation. For additional
information, refer to Skyworks Definition of
Lead (Pb)-Free, document number SQ04-0073.
Description
The SE5516A is a complete 802.11a/b/g/n/ac WLAN RF Front-End
Module (FEM) that provides all the functionality of the Power
Amplifiers (PAs), filtering, power detector, transmit/receive (T/R)
switch, diplexers, and associated matching.
The device provides a complete 2.4 GHz and 5.0 GHz WLAN RF
solution from the output of the transceiver to the antenna in an
ultra-compact form factor. The SE5516A delivers < 2% EVM at
rated AC power, which meets the stringent linearity conditions of
the 802.11ac standard.
All RF ports are matched to 50 Ω to simplify the PCB layout and
the interface to the transceiver. The device also includes a
transmitter power detector with 20 dB of dynamic range for each
transmit chain. Each PA has a separate digital enable control for
transmitter on/off control. The power ramp rise/fall time is
< 0.4 μs.
The SE5516A also provides a notch filter from 3.260 to 3.267 GHz
and 3.28 to 3.89 GHz before the input of each 2.4 GHz and
5.0 GHz PA, respectively.
The SE5516A is manufactured in a compact, 4 x 4 mm, 24-pin
Land Grid Array (LGA) package.
A functional block diagram is shown in Figure 1. The pin
configuration and package are shown in Figure 2. Signal pin
assignments and functional pin descriptions are provided in
Table 1.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202396H • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • February 11, 2014
1
GND
GND
DET
VCC4
VCC3
ENA
DATA SHEET • SE5516A DUAL-BAND 802.11a/b/g/n/ac WLAN FEM
24
23
22
21
20
19
17
GND
GND
3
16
RA
ANT
4
15
RG
GND
5
14
GND
C1
6
13
TG
7
8
9
10
11
12
GND
2
GND
GND
VCC2
TA
VCC1
18
GND
1
C0
ENG
S2934
Figure 2. SE5516A Pinout – 24-Pin LGA
(Top View)
Table 1. SE5516A Signal Descriptions
Pin
Name
Description
Pin
Name
Description
1
ENG
2.4 GHz PA enable
13
TG
2.0 GHz transmit RF input
2
GND
Ground
14
GND
Ground
3
GND
Ground
15
RG
2.0 GHz receive RF output
4
ANT
Antenna
16
RA
5.0 GHz receive RF output
5
GND
Ground
17
GND
Ground
6
C1
Switch control logic 1
18
TA
5.0 GHz transmit RF input
7
C0
Switch control logic 0
19
ENA
5.0 GHz PA enable
8
GND
Ground
20
VCC3
Supply voltage
9
VCC1
Supply voltage
21
VCC4
Supply voltage
10
VCC2
Supply voltage
22
DET
2.0/5.0 GHz power detector output
11
GND
Ground
23
GND
Ground
12
GND
Ground
24
GND
Ground
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
2
February 11, 2014 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202396H
DATA SHEET • SE5516A DUAL-BAND 802.11a/b/g/n/ac WLAN FEM
Table 2. SE5516A Absolute Maximum Ratings (Note 1)
Parameter
Symbol
Supply voltage
VCC
PA enable voltage (pins ENA and ENG)
Maximum input power to TA and TG pins with ANT terminated in 6:1
load or better:
Minimum
Maximum
Units
–0.3
+3.6
V
–0.3
+3.6
V
+12
+5
dBm
dBm
PIN
@ +25C
@ –40C
Operating temperature
TA
–40
+85
C
Storage temperature
TSTG
–40
+150
C
0
3.6
V
–3
dBm
1000
250
V
V
Switch logic control
C0, C1
LNA power (receive mode)
PRX
Electrostatic discharge:
ESD
ANT pin, Human Body Model (HBM), Class 1C
All other pins, HBM, Class 1A
Note 1: Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other
parameters set at or below their nominal value. Exceeding any of the limits listed here may result in permanent damage to the device.
CAUTION: Although this device is designed to be as robust as possible, Electrostatic Discharge (ESD) can damage this device. This device
must be protected at all times from ESD. Static charges may easily produce potentials of several kilovolts on the human body
or equipment, which can discharge without detection. Industry-standard ESD precautions should be used at all times.
Table 3. SE5516A Recommended Operating Conditions
Parameter
Minimum
Typical
Maximum
Units
VCC
3.0
3.3
3.6
V
Operating temperature
TA
–40
+25
+85
C
Junction temperature
TJ
+150
C
Supply voltage
Symbol
Electrical and Mechanical Specifications
The absolute maximum ratings of the SE5516A are provided in
Table 2. The recommended operating conditions are specified in
Table 3 and electrical specifications are provided in Tables 4
through 12.
Typical performance characteristics of the SE5516A are illustrated
in Figures 3 and 4.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202396H • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • February 11, 2014
3
DATA SHEET • SE5516A DUAL-BAND 802.11a/b/g/n/ac WLAN FEM
Table 4. SE5516A Electrical Specifications: DC Characteristics (Note 1)
(VCC = 3.3 V, TA = +25 C, All Unused Ports Terminated with 50 Ω, Unless Otherwise Noted)
Parameter
Total 802.11a transmit supply current
Total 802.11g transmit supply current
Symbol
Test Condition
Min
Typical
Max
Units
ICQ_A
No RF
175
210
mA
ICC_A
POUT = +16 dBm,
54 Mbps, OFDM signal,
64 QAM
230
255
mA
ICQ_G
No RF
135
165
mA
ICC_G
POUT = +18 dBm,
54 Mbps, OFDM signal,
64 QAM
175
195
mA
Total 802.11b transmit supply current
ICC_B
POUT = +21 dBm,
11 Mbps, CCK signal,
BT = 0.45
200
220
mA
Total 802.11ac transmit supply current, 2G
ICC_AC2G
POUT = +16 dBm,
256 QAM, MCS9, 40 MHz
155
175
mA
Total 802.11ac transmit supply current, 5G
ICC_AC5G
POUT = +13 dBm,
256 QAM, MCS9, 80 MHz
190
215
mA
Total receive supply current, 2G
ICC_RX2
ENG = ENA = 0 V, LNA on,
switch condition 1
12
mA
Total receive supply current, 5G
ICC_RX5
ENG = ENA = 0 V, LNA on,
switch condition 4
12
mA
Total supply current
ICC_OFF
No RF, ENG = ENA = 0 V,
switch condition 3 or 6
50
μA
Max
Units
Note 1: Performance is guaranteed only under the conditions listed in this Table.
Table 5. SE5516A Electrical Specifications: Logic Characteristics (Note 1)
(VCC = 3.3 V, TA = +25 C, All Unused Ports Terminated with 50 Ω, Unless Otherwise Noted)
Parameter
Symbol
Test Condition
Min
Typical
Logic high voltage for ENG and ENA
(module on)
VENH
1.8
VCC
V
Logic low voltage for ENG and ENA
(module off)
VENL
0
0.5
V
Input current logic high voltage
(ENG and ENA)
IENH
350
400
μA
Input current logic low voltage
(ENG and ENA)
IENL
0.2
Note 1: Performance is guaranteed only under the conditions listed in this Table.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
4
February 11, 2014 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202396H
μA
DATA SHEET • SE5516A DUAL-BAND 802.11a/b/g/n/ac WLAN FEM
Table 6. SE5516A Electrical Specifications: Switch Characteristics (Note 1)
(VCC = VEN = 3.3 V, TA = +25 C, All Unused Ports Terminated with 50 Ω, Unless Otherwise Noted)
Parameter
Symbol
Test Condition
Min
Typical
Max
Units
Control voltage (on state)
VCTL_ON
3.0
3.6
V
Control voltage (off state)
VCTL_OFF
0
0.2
V
Low loss switch control voltage
SWON
High state = VCTL_ON –
VCTL_OFF
2.8
VCC
V
High loss switch control voltage
SWOFF
Low state = VCTL_OFF –
VCTL_OFF
0
0.3
V
Switch control bias current
RF applied
No RF
ICTL_ON
C0 and C1 pins driven
high
100
30
μA
μA
Control input capacitance
CCTL
100
pF
Note 1: Performance is guaranteed only under the conditions listed in this Table.
Table 7. SE5516A Electrical Specifications: 2.4 GHz Transmit Characteristics (1 of 2) (Note 1)
(VCC = ENG = C0 = 3.3 V, ENA = C1 = 0 V, TA = +25 C, All Unused Ports Terminated with 50 Ω, Unless Otherwise Noted)
Parameter
Symbol
Test Condition
Frequency range
f
Output power, 802.11g
POUT_802.11G
54 Mbps OFDM signal, 64
QAM, DEVM = 3%, input
signal EVM < 1%,
802.11g mask compliant
Output power, 802.11n
POUT_802.11N
OFDM signal, MCS7,
HT40, DEVM = 3%,
802.11n mask compliant,
±11 MHz offset, RBW =
100 kHz, VBW = 30 kHz
Min
2400
Output power, 802.11b
POUT_802.11AC
POUT_802.11B
40 MHz, 256 QAM, MCS9,
DEVM = 1.8%, 802.11ac
mask compliant
Max
Units
2500
MHz
+18
dBm
dBm
+18
dBm
+17
DEVM = 2.5%
Output power, 802.11ac
Typical
dBm
+16
DEVM = 1.4%
+15
dBm
11 Mbps CCK signal,
BT = 0.45,
ACPR (±11 MHz offset)
< –35, ACPR (±22 MHz
offset) < –56
+21
dBm
1 dB compression point
P1dB
+24.0
Small signal gain
|S21|
25
Small signal gain variation over any 40 MHz
channel
Δ|S21|
Small signal gain variation over band
Δ|S21|
Small signal gain @ ½ VCO frequency
|S21|_1.6
1608 to 1656 MHz
Small signal gain @ VCO frequency
|S21|_3.2
3216 to 3312 MHz
1206 to 1242 MHz
3618 to 3726 MHz
Switch state 2
+24.5
dBm
31
dB
0.5
1.0
dB
1
2
dB
12
20
dB
0
+12
–10
dB
dB
dB
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202396H • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • February 11, 2014
5
DATA SHEET • SE5516A DUAL-BAND 802.11a/b/g/n/ac WLAN FEM
Table 7. SE5516A Electrical Specifications: 2.4 GHz Transmit Characteristics (2 of 2) (Note 1)
(VCC = ENG = C0 = 3.3 V, ENA = C1 = 0 V, TA = +25 C, All Unused Ports Terminated with 50 Ω, Unless Otherwise Noted)
Parameter
nd
rd
2 and 3 harmonics
Symbol
2fo, 3fo
Test Condition
Min
Typical
Max
Units
POUT ≤ +21 dBm, 1 Mbps,
CCK
–48
dBm/MHz
POUT ≤ +18 dBm,
802.11g/n, all data rates
–50
dBm/MHz
0.4
μs
Delay and rise/fall time
tDR, tDF
50% of VEN edge and
90/10% of final output
power level
Input return loss
|S11|
7
dB
Output return loss
|S22|
10
dB
Stability
STAB
CW, POUT = +21 dBm,
0.1 to 21 GHz,
load VSWR = 6:1
Ruggedness
Ru
TG = +12 dBm, ANT load
varies over 6:1 VSWR
All non-harmonically related outputs
<–42 dBm/MHz
No irreversible damage
Note 1: Performance is guaranteed only under the conditions listed in this Table.
Table 8. SE5516A Electrical Specifications: 2.4 GHz Receive Characteristics (Note 1)
(VCC = 3.3 V, Switch Condition 1, TA = +25 C, All Unused Ports Terminated with 50 Ω, Unless Otherwise Noted)
Parameter
Frequency range
Symbol
Test Condition
f
Min
Typical
2400
Max
Units
2500
MHz
Small signal gain, LNA enabled
S21
2400 to 2485 MHz
Small signal gain, bypass mode
S21
LNA bypassed, switch
condition 3
10
13
15
dB
–9.5
–8.5
–7.5
dB
Small signal gain, high band gain
@ 5150 to 5850 MHz
S21
Switch condition 1
–17
Small signal gain variation
Δ|S21|
2400 to 2485 MHz, over
any 40 MHz band
0.25
0.50
Noise Figure
NF
De-embedded to device
2.5
2.8
Input return loss
|S11|
5
Output return loss
|S22|
3rd Order Input Intercept Point
IIP3
Switch condition 1
8
1 dB input compression point
IP1dB
LNA enabled
LB
Switch condition 2,
POUT = PSAT
Enable time
tEN
50% of C0 or C1 edge and
90/100% of final output
power levels:
10
PSAT + 10
dB
10
dB
+2.4
dBm
dBm
+8.0
dBm
39
dB
(Note 2)
0.2
μs
(Note 3)
1.0
μs
Note 1: Performance is guaranteed only under the conditions listed in this Table.
Note 2: Timing applies when transitioning in either direction between switch conditions 1 and 3 (see Table 13).
Note 3: Timing applies when transitioning in either direction between switch conditions 2, 4, 5, or 6 and switch conditions 1 or 3 (see Table 13).
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
6
dB
dB
–7.5
LNA bypassed, switch
condition 3
Loopback isolation (ANT to RG pins)
dB
February 11, 2014 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202396H
DATA SHEET • SE5516A DUAL-BAND 802.11a/b/g/n/ac WLAN FEM
Table 9. SE5516A Electrical Specifications: 5.0 GHz Transmit Characteristics (Note 1)
(VCC = ENA = C0 = 3.3 V, ENG = C1 = 0 V, TA = +25 C, All Unused Ports Terminated with 50 Ω, Unless Otherwise Noted)
Parameter
Symbol
Frequency range
f
Output power, 802.11n
POUT_802.11N
Output power, 802.11ac
POUT_802.11AC
Test Condition
Min
Typical
4900
Max
Units
5900
MHz
OFDM signal, MCS7,
HT40, DEVM = 3%,
802.11n mask compliant,
±11 MHz offset, RBW =
100 kHz, VBW = 30 kHz
+16
dBm
DEVM = 2.7%
+15
dBm
80 MHz, 256 QAM, MCS9,
DEVM = 1.8%, input
signal EVM < 0.6%,
802.11ac mask compliant
+13
dBm
DEVM = 1.6%
+12
dBm
1 dB compression point
P1dB
+21.0
Small signal gain
S21
Small signal gain variation over 80 MHz
channel
Δ|S21|
Small signal gain variation over sub-bands
Δ|S21|
5.15 to 5.50 GHz and
5.70 to 5.90 GHz
Isolation
S12
2nd and 3rd harmonics
Delay and rise/fall time
Input return loss
|S11|
+22.5
dBm
+32
0
+2
dB
dB
dB
1
dB
2
dB
Switch state 5,
4.9 to 5.9 GHz
–45
dB
2fo, 3fo
@ +20 dBm, MCS0
–50
dBm/MHz
tDR, tDF
50% of VEN edge and
90/10% of final output
power level
0.4
μs
In band
@ 1.640 to 1.942 GHz
@ 3.280 to 3.900 GHz
+25
10
dB
Output return loss
|S22|
10
dB
Stability
STAB
64 QAM, POUT = +16 dBm,
0.1 to 21 GHz,
load VSWR = 6:1
All non-harmonically related outputs
<–42 dBm/MHz
–
Ruggedness
Ru
TA = +12 dBm, ANT load
varies over 6:1 VSWR
No irreversible damage
–
Note 1: Performance is guaranteed only under the conditions listed in this Table.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202396H • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • February 11, 2014
7
DATA SHEET • SE5516A DUAL-BAND 802.11a/b/g/n/ac WLAN FEM
Table 10. SE5516A Electrical Specifications: 5.0 GHz Receive Characteristics (Note 1)
(VCC = 3.3 V, Switch Condition 4, TA = +25 C, All Unused Ports Terminated with 50 Ω, Unless Otherwise Noted)
Parameter
Symbol
Frequency range
f
Small signal gain
S21
Test Condition
Min
Typical
4900
Switch condition 4:
4900 to 5850 MHz
2400 to 2500 MHz
Max
Units
5850
MHz
+10
+12
–28
+14
–17
dB
dB
–10.5
–9.0
–7.5
dB
Small signal gain, bypass mode
S21
LNA bypassed, switch
condition 6
Small signal gain variation
Δ|S21|
4900 to 5850 MHz, over
any 80 MHz band
–0.5
+0.5
dB
Over entire band
–1.0
+1.0
dB
Noise Figure
NF
Input return loss
|S21|
8
10
dB
Output return loss
|S22|
6
10
dB
+3.5
dBm
rd
De-embedded to device
2.8
3.0
dB
3 Order Input Intercept Point
IIP3
Switch condition 4
1 dB input compression point
IP1dB
LNA enabled
–6
dBm
LNA bypassed, switch
condition 6
+6
dBm
Loopback isolation (ANT to RA pins)
LB
Switch condition 5,
POUT = PSAT
Enable time
tEN
50% of C0 or C1 edge and
90/100% of final output
power levels:
33
dB
(Note 2)
0.2
μs
(Note 3)
1.0
μs
Note 1: Performance is guaranteed only under the conditions listed in this Table.
Note 2: Timing applies when transitioning in either direction between switch conditions 4 and 6 (see Table 13).
Note 3: Timing applies when transitioning in either direction between switch conditions 1, 2, 3, or 5 and switch conditions 4 or 6 (see Table 13).
Table 11. SE5516A Electrical Specifications: 2.4 GHz Power Detector Characteristics (Note 1)
(VCC = 3.3 V, Switch Condition 2, TA = +25 C, All Unused Ports Terminated with 50 Ω, Unless Otherwise Noted)
Parameter
Symbol
Test Condition
Max
Units
2400
Min
2500
MHz
0
+22
dBm
0.95
V
Frequency range
f
Power detector range, peak power
PDR
Measured at ANT pin
Output voltage @ POUT = +22 dBm
PDVP22
Measured into 26.5 kΩ
Output voltage @ POUT = +18 dBm
PDVP18
Measured into 26.5 kΩ
Output voltage, no RF output power
PDVPNORF
Measured into 26.5 kΩ
0.15
Power detector low-pass filter –3 dB corner
frequency
LPF-3DB
Measured into 26.5 kΩ
35
Power detector accuracy
PDETACC
Measured into 3:1 load at
ANT port
0.70
Typical
0.83
0.55
–1.5
0.18
V
0.22
MHz
+1.5
Note 1: Performance is guaranteed only under the conditions listed in this Table.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
8
V
February 11, 2014 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202396H
dB
DATA SHEET • SE5516A DUAL-BAND 802.11a/b/g/n/ac WLAN FEM
Table 12. SE5516A Electrical Specifications: 5.0 GHz Power Detector Characteristics (Note 1)
(VCC = 3.3 V, Switch Condition 5, TA = +25 C, All Unused Ports Terminated with 50 Ω, Unless Otherwise Noted)
Parameter
Symbol
Test Condition
Frequency range
f
Power detector range, peak power
PDR
Measured at ANT pin
Output voltage @ POUT = +20 dBm
PDVP20
Measured into 26.5 kΩ:
5.15 to 5.35 GHz
5.47 to 5.725 GHz
5.725 to 5.875 GHz
Min
Typical
Max
Units
4900
5900
MHz
0
+21
dBm
0.80
0.82
0.75
1.00
1.02
0.95
V
V
V
Output voltage @ POUT = +16 dBm
PDVP16
Measured into 26.5 kΩ
0.60
Output voltage, no RF output power
PDVPNORF
Measured into 26.5 kΩ
0.15
Power detector low-pass filter –3 dB corner
frequency
LPF-3DB
Measured into 26.5 kΩ
35
Power detector accuracy
PDETACC
Measured into 3:1 load at
ANT port
–1.5
0.18
V
0.22
V
MHz
+1.5
dB
Note 1: Performance is guaranteed only under the conditions listed in this Table.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202396H • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • February 11, 2014
9
DATA SHEET • SE5516A DUAL-BAND 802.11a/b/g/n/ac WLAN FEM
Typical Performance Characteristics
1.2
Power Detector Voltage (V)
1.1
1.0
0.9
0.8
0.7
0.6
0.5
0.4
2400 MHz
2450 MHz
2500 MHz
0.3
0.2
3
4
5
6
7
8
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23
Output Power (dBm)
Figure 3. Power Detector vs Output Power Over Frequency
@ 2.5 GHz
1.2
Power Detector Voltage (V)
1.1
1.0
0.9
0.8
0.7
0.6
0.5
5280 MHz
5470 MHz
5660 MHz
5850 MHz
0.4
0.3
0.2
3
4
5
6
7
8
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23
Output Power (dBm)
Figure 4. Power Detector vs Output Power Over Frequency
@ 5.0 GHz
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
10
February 11, 2014 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202396H
DATA SHEET • SE5516A DUAL-BAND 802.11a/b/g/n/ac WLAN FEM
Evaluation Board Description
Package and Handling Information
The SE5516A Evaluation Board is used to test the performance of
the SE5516A WLAN FEM. An Evaluation Board schematic diagram
is provided in Figure 5. A photograph of the Evaluation Board is
shown in Figure 6. Component values for the SE5516A Evaluation
Board are listed in Table 14.
Since the device package is sensitive to moisture absorption, it is
baked and vacuum packed before shipping. Instructions on the
shipping container label regarding exposure to moisture after the
container seal is broken must be followed. Otherwise, problems
related to moisture absorption may occur when the part is
subjected to high temperature during solder assembly.
Evaluation Board Setup Procedure
The SE5516A is rated to Moisture Sensitivity Level 3 (MSL3) at
240 C. It can be used for lead or lead-free soldering. For
additional information, refer to the Skyworks Application Note,
Solder Reflow Information, document number 200164.
Step 1: Connect system ground to pin 2 of connector J6.
Step 2: Apply 3.3 V to pin 1 of connector J6.
Step 3: Select a path according to the logic shown in Table 13.
Package Dimensions
Care must be taken when attaching this product, whether it is
done manually or in a production solder reflow environment.
Production quantities of this product are shipped in a standard
tape and reel format.
The PCB layout footprint for the SE5516A is provided in Figure 7.
Typical case markings are shown in Figure 8. Package
dimensions for the 24-pin LGA are shown in Figure 9, and tape
and reel dimensions are provided in Figure 10.
Table 13. SE5516A Evaluation Board Switch Control Logic
Logic
C0
(Pin 1, J16
Header)
C1
(Pin 5, J16
Header)
ENA
(Pin 7, J7
Header)
ENG
(Pin 3, J7
Header)
SP3T
LNA
Bypass
1
0
1
0
0
RG
RG enable
Open
2
0
0
0
1
TG
RG off
RG bypass
3
0
0
0
0
RG
RG off
RG bypass
4
1
1
0
0
RA
RA enable
Open
Condition
Note:
State
5
1
0
1
0
TA
RA off
RA bypass
6
1
0
0
0
RA
RA off
RA bypass
“0” = 0 V. “1” = +3.3 V. Any state other than described in this Table places the switch into an undefined state. An undefined state will not damage the device.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202396H • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • February 11, 2014
11
DATA SHEET • SE5516A DUAL-BAND 802.11a/b/g/n/ac WLAN FEM
VCC
J6
1
C8
2.2 μF
C4
220 pF
2
C6
10 pF
2.4/5.0 GHz
Power Detector Output
ENA
17
GND
GND
GND
RA
ANT
RG
3
J5
4
J2
5 GHz Rx RF Output
16
15
J3
5
14
GND
2 GHz Rx RF Output
GND
6
J4
13
8
9
TG
10
11
2 GHz Tx RF Input
GND
GND
VCC2
GND
C0
7
VCC1
C1
Switch Control
5 GHz Tx RF Input
TA
2
Antenna
J1
18
ENG
2.4 GHz PA Enable
5 GHz PA Enable
C2
10 pF
19
VCC3
20
VCC4
21
DET
1
22
GND
23
GND
24
12
Switch Control
Supply Voltage
C5
10 pF
VCC
VCC
J16
C0
C1
J7
1
2
DET
1
2
3
4
ENG
3
4
5
6
5
6
7
8
7
8
ENA
Note: Some component labels may be different than the corresponding component symbol shown here.
Component values, however, are accurate as of the date of this Data Sheet.
Figure 5. SE5516A Evaluation Board Schematic
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
12
February 11, 2014 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202396H
S2935
DATA SHEET • SE5516A DUAL-BAND 802.11a/b/g/n/ac WLAN FEM
Figure 6. SE5516A Evaluation Board Photo
Table 14. SE5516A Evaluation Board Bill of Materials
Component
Size
Value
Vendor
Part #
Comments
C2, C5, C6
0402
10 pF
Murata
GRM1555C1H100JZ01
Multilayer ceramic
C4
0402
220 pF
Murata
GRM1555C1H221JA01
Multilayer ceramic
C8
0805
2.2 μF
Murata
GRM21BR71A225KA01L
Ceramic capacitor, 10 V, 10% X7R
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202396H • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • February 11, 2014
13
DATA SHEET • SE5516A DUAL-BAND 802.11a/b/g/n/ac WLAN FEM
4.3
Pin 24
2.4
Pin 1 Indicator
0.40 X 45°
Pin 1
24X 0.65
1.2
24X 0.3
2.4
4.3
0.5 Pitch
1.2
Stencil aperture size for center ground pad
should be 80% to 100 % (by area) of the
solder mask opening.
Package Outline
Stencil Aperture
Top View
4.3
Pin 24
4.4
0.25 Typ.
14X 0.65
Pin 24
2.4
Pin 1 Indicator
0.40 X 45°
Pin 1
Pin 1
24X 0.75
1.2
14X 0.3
24X 0.4
0.5 Pitch 4.3
0.51 Pitch
0.5 Pitch 4.4
2.4
1.2
Thermal Via Array, ∅0.3 mm
on 0.6 mm pitch will improve
thermal performance.
NOTE: thermal vias should be
tented with solder mask,
30-35 mm Cu plating
recommended.
Package Outline
Opening size of 60% to
100 % of exposed center
opening shown.
Package Outline
Metallization
Top View
Solder Mask Opening
Top View
S3017
All dimensions are in millimeters
Figure 7. SE5516A PCB Layout Footprint
Pin 1
Indicator
Skyworks Part #
Lot #
YY = Calendar Year
WW = Week
CC = County Code
Figure 8. Typical Case Markings
(Top View)
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
14
February 11, 2014 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202396H
4X 1.25
B
Pin 1
Indicator
4X 0.75
12X 1.9
4
4X 0.25
DATA SHEET • SE5516A DUAL-BAND 802.11a/b/g/n/ac WLAN FEM
Pin 24
A
Pin 1 Indicator
0.40 X 0.40
12X 1.9
Pin 1
2X 1.2
4X 0.75
0
4
0.1
Top View
4X 1.25
E
D A
Solder Mask Opening
0.2 A B C
C
0.15 A B C
F
0
Side View
Metal Pad Edge
24X SMT Pad
0.1 A B C
Bottom View
Solder
Mask Edge
Solder
Mask Edge
B C
2X 1.2
1.01 ± 0.1
4X 0.25
Metal Pad
Edge
0.04 X 0.04
Solder
Mask Edge
Metal Pad Edge
(0.05)
(0.05)
0.4 ± 0.05
0.4 ± 0.1
0.3 ± 0.05
0.4 ± 0.05
(0.1)
0.4 ± 0.05
(0.1)
(0.1)
(0.05)
0.3 ± 0.05
0.3 ± 0.05
Detail A
Detail B
Pad
Scale: 2X
2X This rotation
1X Rotated 180°
2X Rotated 90° CW
3X Rotated 90° CCW
Detail C
Pad
Scale: 2X
2X This rotation
3X Rotated 180°
2X Rotated 90° CW
Pad
Scale: 2X
1X This rotation
1X Rotated 180°
1X Rotated 90° CCW
1X Mirrored 45°
0.4 ± 0.025
0.04 X 0.04
Solder
Mask Edge
Metal
Pad Edge
0.4 ± 0.1
(0.1)
(0.05)
0.3 ± 0.05
0.4 ± 0.05
(0.1)
(0.05)
(0.1)
0.04 X 0.04
Metal Pad Edge
(0.05)
0.3 ± 0.05
0.3 ± 0.05
Solder
Mask Edge
0.04 X 0.04
Metal Pad Edge
(0.1)
Detail D
Solder Mask Edge
Detail E
Pad
Scale: 2X
1X This rotation
1X Rotated 180°
Pad
Scale: 2X
1X This rotation
1X Mirrored 180°
(0.05)
Detail F
Pad
Scale: 2X
1X This rotation
All measurements are in millimeters
Dimensioning and tolerancing according to ASME Y14.5M-1994
S2933
Figure 9. SE5516A 24-Pin LGA Package Dimensions
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202396H • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • February 11, 2014
15
DATA SHEET • SE5516A DUAL-BAND 802.11a/b/g/n/ac WLAN FEM
0.229 ± 0.02 (T)
2.00 ± 0.05
4.00 ± 0.10
8.00 ± 0.10
ø1.50
Pin 1
Indicator
1.75 ± 0.10
± 0.10
B
A
B
1.73 ± 0.10 (Ko)
B
ø1.50
12.00 +0.30/–0.10
4.35 ± 0.10 (Bo)
A
5.50 ± 0.05
8o Max
± 0.25
4.35 ± 0.10 (Ao)
7o Max
A
Notes:
1. Carrier tape material: black conductive polycarbonate
or polysterene
2. Cover tape material: transparent conductive PSA
3. Cover tape size: 9.3 mm width
4. ESD surface resistivity is ≤1 x 108 Ohms/square per EIA, JEDEC
tape and reel specification.
5. Tolerance: .XX = ±0.10
6. All measurements are in millimeters
Figure 10. SE5516A Tape and Reel Dimensions
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
16
February 11, 2014 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202396H
S3496
DATA SHEET • SE5516A DUAL-BAND 802.11a/b/g/n/ac WLAN FEM
Ordering Information
Model Name
SE5516A WLAN FEM
Manufacturing Part Number
SE5516A
Evaluation Board Part Number
SE5516A-EVB
Copyright © 2012-2014 Skyworks Solutions, Inc. All Rights Reserved.
Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by
Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the
information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to
update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes.
No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or
information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions
of Sale.
THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A
PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY
DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS
SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION,
LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury,
death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any
damages resulting from such improper use or sale.
Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of
products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for
applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters.
Skyworks, the Skyworks symbol, and “Breakthrough Simplicity” are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands
and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com,
are incorporated by reference.
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com
202396H • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • February 11, 2014
17