PRELIMINARY DATA SHEET SKY77336 Power Amplifier Module for Quad-Band GSM / GPRS Applications Description • Quad-band cellular handsets SKY77336 Power Amplifier Module (PAM) is designed in a compact form factor for quad-band cellular handsets comprising GSM850/900, DCS1800 and PCS1900, supporting Gaussian Minimum-Shift Keying (GMSK) and Polar Enhanced Data for GSM Evolution (EDGE) modulation. Class 12 General Packet Radio Service (GPRS) multi-slot operation is also supported. • GMSK Modulation - Class 4 GSM850/900 - Class 1 DCS1800/ PCS1900 - Class 12 GPRS multi-slot operation • EDGE modulation - Class E2 GSM850/900 - Class E2 DCS1800/ PCS1900 Features • High efficiency: - GSM850, 55% - GSM900, 55% - DCS, 53% - PCS, 53% The module consists of GSM850/900 PA and DCS1800/PCS1900 PA blocks, impedance matching circuitry for 50 Ω input and output impedances, and a Power Amplifier Control (PAC) block. The custom CMOS integrated circuit provides the internal PAC function and interface circuitry. Fabricated in InGaP/GaAs, the Heterojunction Bipolar Transistor (HBT) PA blocks support the GSM850/900 bands and DCS1800/PCS1900 bands. Both PA blocks share common power supply pads to distribute current. The InGaP/GaAs die, Silicon (Si) controller die, and passive components are mounted on a multi-layer laminate substrate and the entire assembly is encapsulated with plastic overmold. RF input and output ports of the SKY77336 are internally matched to a 50 Ω load to reduce the number of external components for a quad-band design. Extremely low leakage current (10 μA, typical) of the PAM module maximizes handset standby time. The SKY77336 also contains band-select switching circuitry to select GSM (logic 0) or DCS/PCS (logic 1) as determined from the Band Select (BS) signal. See Figure 1 shown below. • Small outline - 5 x 5 mm • Low profile - 1.15 mm Max • Low VRAMP current - 10 μA Figure 1. SKY77336 Functional Block Diagram Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 200780E • Skyworks Proprietary and Confidential information. • Products and product information are subject to change without notice. • September 19, 2008 1 PRELIMINARY DATASHEET SKY77336 POWER AMPLIFIER MODULE FOR QUAD-BAND GSM / GPRS Electrical Specifications The absolute maximum ratings of SKY77336 are provided in Table 1. Table 2 specifies the recommended operating conditions for achieving the electrical performance shown in Table 5 through Table 11. Table 3 provides loop requirement and Table 4 provides the mode control logic. Table 1. SKY77336 Absolute Maximum Ratings 1 Parameter Symbol RF Input Power Minimum Nominal Maximum Units — 6 15 dBm — 3.5 5.5 V VCONT –0.5 — VBATT – 0.2 V PIN Supply Voltage (≤ 100 ms) VBATT Supporting Operation at Max. POUT @ 50 ohm Load @ +25 °C Logic Signals (ENABLE, BS) Input Modulating Signal and Power Control VAPC –0.5 1.6 VBATT – 0.2 V Operating 2 TCASE –30 25 +90 °C Storage TSTG –55 — +150 Re-flow solder TSOLDER — — J-STD-020C Moisture Sensitivity Level MSL — — 3/260 Burst Duty Cycle DB — 12.5 50 Voltage Standing Wave Ratio VSWR — 2.5:1 100:1 Temperatures % 1 No damage assuming only one parameter is set at limit at a time with all other parameters set at nominal values. 2 Case Operating Temperature refers to the temperature of the GROUND PAD at the underside of the package. Table 2. SKY77336 Recommended Operating Conditions Parameter Supply Voltage Leakage Current VBATT = 4.8 V Tx_EN = 0 V VAPC = 0-1.6 V No RF applied Operating Temperature (full specifications) Symbol Minimum Nominal Maximum Units VBATT 3.0 3.5 4.8 V IL — — 10 uA TCASE °C –25 +25 +85 Power Supply Noise Rejection — TBD — Tx Enable Switch Time — — 1 us Tx Enable Current — 10 20 uA Band Select Current — 10 20 uA Duty Cycle — — 50 % Analog Power Control Voltage Range 0.0 — 1.6 V — — 10 uA — 50 — Ω Analog Power Control Input Current Impedance System for RF Ports Z Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 2 September 19, 2008 • Skyworks Proprietary and Confidential information. • Products and product information are subject to change without notice. • 200780E SKY77336 POWER AMPLIFIER MODULE FOR QUAD-BAND GSM / GPRS PRELIMINARY DATASHEET Table 3. SKY77336 Loop Requirement Parameter VAPC Bandwidth (Corresponding to the f – 3 dB of the Transfer Function VOUT/VAPC) Symbol Test Conditions BW_VAPC PIN = Min. to Max. POUT = Min. to Max. VBATT = Min. to Max. TCASE = Min. to Max. Minimum Typical Maximum Unit 6 9 14 MHz Table 4. SKY77336 Control Logic Mode Input Control Bits 850/EGSMTx DCS/PCSTx Tx_EN BS Standby 0 X Disable Disable Tx 850/EGSM 1 0 Enable Disable Tx DCS/PCS 1 1 Disable Enable Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 200780E • Skyworks Proprietary and Confidential information. • Products and product information are subject to change without notice. • September 19, 2008 3 PRELIMINARY DATASHEET SKY77336 POWER AMPLIFIER MODULE FOR QUAD-BAND GSM / GPRS Table 5. SKY77336 Electrical Specifications 1 (1 of 2) 850/900 Tx GMSK & EDGE Mode Parameter Frequency Symbol GSM850 f GSM900 Condition Minimum Typical Maximum Unit — 824 — 849 MHz — 880 — 915 Input Power PIN — 3.0 6.0 8.0 dBm Supply Voltage VBATT — 3.0 3.5 4.8 V Leakage Current IL VBATT = 3.5 V VAPC ≤ 25 mV TCASE = +25 °C No input power — — 10 μA 2ND 2fo 6.5 dBm ≤ POUT ≤ 34.5 dBm at 50 ohm load — — –10 dBm 3RD to 15TH 3f0 to 15f0 6.5 dBm ≤ POUT ≤ 34.5 dBm at 50 ohm load — — –15 3RD to 7 TH 3f0 to 7f0 6.5 dBm ≤ POUT ≤ 34.5 dBm VBATT = 3.5 V TCASE = +25 °C Load: VSWR of 5:1 for all phases. — –12 –10 Fundamental — — 5 Harmonics Cross Harmonics Harmonics — — –20 Current at Mismatch IBATT_LOAD Load VSWR = 5:1, all phase angles. VAPC is set to the number that delivers POUT = 34.5 dBm at 50 ohm load — 2.1 — Input VSWR ΓIN POUT ≤ 34.5 dBm — — 2.5:1 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 4 September 19, 2008 • Skyworks Proprietary and Confidential information. • Products and product information are subject to change without notice. • 200780E dBm A SKY77336 POWER AMPLIFIER MODULE FOR QUAD-BAND GSM / GPRS PRELIMINARY DATASHEET Table 5. SKY77336 Electrical Specifications 1 (2 of 2) [continued] 850 / 900 Tx GMSK & EDGE Mode Parameter Symbol Forward Isolation Stability S Spurious Ruggedness Noise Power Condition Minimum Typical Maximum Unit Tx_EN = low PIN = 8 dBm — — –30 dBm Tx_EN = high PIN = 8 dBm VAPC ≤ 0.2 V — — –15 No parasitic oscillation > –36 dBm All combinations of the following parameters. PIN = Min. to Max. VBATT = 3.0 V to 4.8 V TCASE = –20 °C to +85 °C Load VSWR = 10:1, all phase angles. f < 1 GHz Load VSWR = 8:1 — — –36 f > 1 GHz Load VSWR = 8:1 — — –30 No module damage or permanent degradation Ru All combinations of the following parameters. PIN = Min. to Max. VBATT = 3.0 V to 4.8 V VBATT = 7.0 V for ≤ 1 μs VBATT = 5.5 V for ≤ 100 ms Load VSWR= 10:1, all phase angles PNOISE RX = 869 to 894 MHz VBATT = 3.5 V PIN = 6 dBm TCASE = +25 °C — –87 — GSM 900 RX = 925 to 935 MHz VBATT = 3.5 V PIN = 6 dBm TCASE = +25 °C — — –76 GSM 900 RX = 935 to 960 MHz VBATT = 3.5 V PIN = 6 dBm TCASE = +25 °C — –87 — GSM 850 dBm dBm/ 100 kHZ 1 Unless otherwise specified: 50 Ω system; pulsed operation with pulse width 2308 μs; duty cycle 1:8; TCASE = –20 °C to 85 °C; VBATT = 3.0 V to 4.8 V Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 200780E • Skyworks Proprietary and Confidential information. • Products and product information are subject to change without notice. • September 19, 2008 5 PRELIMINARY DATASHEET SKY77336 POWER AMPLIFIER MODULE FOR QUAD-BAND GSM / GPRS Table 6. SKY77336 Electrical Specifications 1 850 / 900 Tx GMSK Mode Parameter Frequency Range Symbol GSM850 f GSM900 Condition Minimum Typical Maximum Unit — 824 — 849 MHz — 880 — 915 Input Power PIN — 3.0 6.0 8.0 dBm Supply Voltage VBATT — 3.0 3.5 4.8 V Output Power (Average) POUT PIN = 6 dBm VBATT = 3.5 V TCASE = +25 °C 34.5 35.0 — dBm POUT_DEG PIN = 0 dBm VBATT = 3.4 V – 4.8 V TCASE = –20 °C to 85 °C VAPC is set to deliver POUT = 34.5 dBm at VBATT = 3.5 V TCASE = +25° C 32.5 — — PAE PIN = 6 dBm POUT = Max. VBATT = 3.5 V TCASE = +25 °C 50 55 — % The change in phase for POUT VAPC = sawtooth signal f = 2166 Hz POUT ≤ 34.5 dBm — 1 — deg./dB 49.5 — — dB Power Added Efficiency Phase Change Dynamic Range — 1 Unless otherwise specified: 50 Ω system; pulsed operation with pulse width 2308 μs; duty cycle 1:8; TCASE = –20 °C to 85 °C; VBATT = 3.0 V to 4.8 V Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 6 September 19, 2008 • Skyworks Proprietary and Confidential information. • Products and product information are subject to change without notice. • 200780E SKY77336 POWER AMPLIFIER MODULE FOR QUAD-BAND GSM / GPRS PRELIMINARY DATASHEET Table 7. SKY77336 Electrical Specifications 1 850 / 900 Tx EDGE Mode Parameter Frequency Range Symbol GSM850 f GSM900 Condition Minimum Typical Maximum Unit — 824 — 849 MHz — 880 — 915 Input Power PIN — 3.0 6.0 8.0 dBm Supply Voltage VBATT — 3.0 3.5 4.8 V Output Power (average) POUT PIN = 6 dBm VBATT = 3.5 V TCASE = +25 °C 29 — — dBm POUT_DEG 1 PIN = 0 dBm VBATT = 3.0 V – 4.8 V TCASE = –30 °C to 90 °C at VBATT = 3.5 V TCASE = +25 °C 28.5 — — PAE PIN = 6 dBm POUT = 28.5 dBm VBATT = 3.5 V TCASE = +25 °C 24 28 — Power Added Efficiency % 1 Unless otherwise specified: 50 Ω system; pulsed operation with pulse width 2308 μs; duty cycle 1:8; TCASE = –20 °C to 85 °C; VBATT = 3.0 V to 4.8 V Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 200780E • Skyworks Proprietary and Confidential information. • Products and product information are subject to change without notice. • September 19, 2008 7 PRELIMINARY DATASHEET SKY77336 POWER AMPLIFIER MODULE FOR QUAD-BAND GSM / GPRS Figure 2. Typical AM/AM and AM/PM Response Charts for Low Band – SKY77336 Power Amplifier Module Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 8 September 19, 2008 • Skyworks Proprietary and Confidential information. • Products and product information are subject to change without notice. • 200780E SKY77336 POWER AMPLIFIER MODULE FOR QUAD-BAND GSM / GPRS PRELIMINARY DATASHEET Table 8. SKY77336 Electrical Specifications 1 (1 of 2) 1800 / 1900 Tx GMSK & EDGE Mode Parameter Frequency Range DCS 1800 Symbol f PCS 1900 Condition Minimum Typical Maximum Unit — 1710 — 1785 MHz — 1850 — 1910 Input Power PIN — 3.0 6.0 8.0 dBm Supply Voltage VBATT — 3.0 3.5 4.8 V Leakage Current IL VBATT = 3.5 V VAPC ≤ 25 mV TCASE = +25 °C No input power — — 10 μA 2ND 2f0 1.5 dBm ≤ POUT ≤ 32 dBm at 50 ohm load — — –10 dBm 3RD to 7TH 3f0 to 7f0 1.5 dBm ≤ POUT ≤ 32 dBm at 50 ohm load — — –15 3RD to 7TH 3f0 to 7f0 1.5 dBm ≤ POUT ≤ 32 dBm VBATT = 3.5 V TCASE = +25 °C Load: VSWR of 5:1 for all phases. — –12 –10 Current at Mismatch IBATT_LOAD Load VSWR = 5:1, all phase angles. VAPC set to the number that delivers POUT = 32 dBm at 50 ohm load. — 1.4 — Input VSWR ΓIN POUT ≤ 32 dBm — — 2.5:1 Harmonics A Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 200780E • Skyworks Proprietary and Confidential information. • Products and product information are subject to change without notice. • September 19, 2008 9 PRELIMINARY DATASHEET SKY77336 POWER AMPLIFIER MODULE FOR QUAD-BAND GSM / GPRS Table 9. SKY77336 Electrical Specifications 1 (2 of 2) [continued] 1800 / 1900 Tx GMSK & EDGE Mode Parameter Symbol Forward Isolation Cross Harmonics Stability S Spurious Ruggedness Noise Power DCS PCS Condition Minimum Typical Maximum Unit Tx_EN = low PIN = 8 dBm — — –30 dBm Tx_EN = high PIN = 8 dBm VAPC ≤ 0.2 V — — –20 Fundamental — — 5 Harmonics — — –20 No parasitic oscillation > –36 dBm All combinations of the following parameters. PIN = Min. to Max. VBATT = 3.0 V to 4.8 V TCASE = -20 °C to +85 °C Load VSWR = 10:1, all phase angles. f < 1 GHz Load VSWR = 8:1 — — –36 f > 1 GHz Load VSWR = 8:1 — — –30 dBm No module damage or permanent degradation Ru All combinations of the following parameters. PIN = Min. to Max. VBATT = 3.0 V to 4.8 V VBATT = 7.0 V for ≤ 1 μs VBATT = 5.5 V for ≤ 100 ms Load VSWR= 10:1, all phase angles. PNOISE RX = 1805 to 1880 MHz VBATT = 3.5 V PIN = 6 dBm TCASE = +25 °C — — –79 RX = 1930 to 1990 MHz VBATT = 3.5 V PIN = 6 dBm TCASE = +25 °C — — –79 1 Unless otherwise specified: 50 Ω system; pulsed operation with pulse width 2308 μs; duty cycle 1:8; TCASE = –20 °C to 85 °C; VBATT = 3.0 V to 4.8 V Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 10 dBm September 19, 2008 • Skyworks Proprietary and Confidential information. • Products and product information are subject to change without notice. • 200780E dBm/ 100 kHz SKY77336 POWER AMPLIFIER MODULE FOR QUAD-BAND GSM / GPRS PRELIMINARY DATASHEET Table 10. SKY77336 Electrical Specifications 1 1800 / 1900 Tx GMSK Parameter Frequency Range GSM1800 Symbol f GSM1900 Condition Minimum Typical Maximum Unit — 1710 — 1785 MHz — 1850 — 1910 Input Power PIN — 3.0 6.0 8.0 dBm Supply Voltage VBATT — 3.0 3.5 4.8 V Output Power (average) POUT PIN = 6 dBm VBATT = 3.5 V TCASE = +25 °C 32.0 33 — dBm POUT_DEG PIN = 0 dBm VBATT = 3.4 V – 4.8 V TCASE = –20 °C to 85 °C VAPC is set to deliver POUT = 32 dBm at VBATT = 3.5 V TCASE = +25 °C 30.5 — — PAE PIN = 6 dBm POUT = Max. VBATT = 3.5 V TCASE = +25° C duty cycle = 1:8 48 53 — The change in phase for POUT VAPC = sawtooth signal f = 2166 Hz POUT ≤ 32 dBm — 1 52 — Power Added Efficiency Phase Change Dynamic Range — % deg./dB — dB 1 Unless otherwise specified: 50 Ω system; pulsed operation with pulse width 2308 μs; duty cycle 1:8; TCASE = –20 °C to 85 °C; VBATT = 3.0 V to 4.8 V Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 200780E • Skyworks Proprietary and Confidential information. • Products and product information are subject to change without notice. • September 19, 2008 11 PRELIMINARY DATASHEET SKY77336 POWER AMPLIFIER MODULE FOR QUAD-BAND GSM / GPRS Table 11. SKY77336 Electrical Specifications 1 1800 / 1900 Tx EDGE Parameter Frequency Range GSM1800 Symbol f GSM1900 Condition Minimum Typical Maximum Unit — 1710 — 1785 MHz — 1850 — 1910 Input Power PIN — 3.0 6.0 8.0 dBm Supply Voltage VBATT — 3.0 3.5 4.8 V Output Power (average) POUT 28.5 — — dBm POUT_DEG 1 PIN = 0 dBm VBATT = 3.0 V – 4.8V TCASE = –30 °C to 90 °C at VBATT = 3.5 V TCASE = +25 °C 28 — — PAE 26 30 — Power Added Efficiency PIN = 6 dBm VBATT = 3.5 V TCASE = +25 °C PIN = 6 dBm POUT = 28.5 dBm VBATT = 3.5 V TCASE = +25 °C duty cycle = 1:8 1 Unless otherwise specified: 50 Ω system; pulsed operation with pulse width 2308 μs; duty cycle 1:8; TCASE = –20 °C to 85 °C; VBATT = 3.0 V to 4.8 V Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 12 September 19, 2008 • Skyworks Proprietary and Confidential information. • Products and product information are subject to change without notice. • 200780E % SKY77336 POWER AMPLIFIER MODULE FOR QUAD-BAND GSM / GPRS PRELIMINARY DATASHEET Figure 3. Typical AM/AM and AM/PM Response Charts for High Band – SKY77336 Power Amplifier Module Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 200780E • Skyworks Proprietary and Confidential information. • Products and product information are subject to change without notice. • September 19, 2008 13 PRELIMINARY DATASHEET SKY77336 POWER AMPLIFIER MODULE FOR QUAD-BAND GSM / GPRS Package Dimensions Figure 4 is a mechanical drawing of the pad layout for the SKY77336, a 16-pad, leadless, PA module. Figure 5 provides a recommended phone board layout footprint for the PAM to help the designer attain optimum thermal conductivity, good grounding, and minimum RF discontinuity for the 50-ohm terminals. Figure 4. Dimensional Diagram for 5 mm x 5 mm x 1.05 mm, 16-Pad MCM Package – SKY77336 Specific Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 14 September 19, 2008 • Skyworks Proprietary and Confidential information. • Products and product information are subject to change without notice. • 200780E SKY77336 POWER AMPLIFIER MODULE FOR QUAD-BAND GSM / GPRS PRELIMINARY DATASHEET Figure 5. Phone Board Layout Footprint for 5 x 5 mm MCM Package – SKY77336 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 200780E • Skyworks Proprietary and Confidential information. • Products and product information are subject to change without notice. • September 19, 2008 15 PRELIMINARY DATASHEET SKY77336 POWER AMPLIFIER MODULE FOR QUAD-BAND GSM / GPRS Package Description Figure 6 shows the device pad configuration and numbering convention, which starts at the upper left as indicated, and increments counter-clockwise around the package. Table 12 lists the pad names and signal descriptions. Figure 1 interprets typical case markings. Figure 7. Typical Case Marking Package Handling Information Figure 6. SKY77336 Pad Configuration Table 12. Pad Signal Names and Functions Pad Signal Function 1 DCS/PCS_IN Input Tx signal 1800 / 1900 MHz 2 BS Band Select 3 TX_EN Enable 4 VBATT Battery Supply Voltage 5 VAPC Input modulating signal / power control 6 NC No connect 7 GND Ground 8 GSM_IN Input Tx signal 850 / 900 MHz 9 GSM_OUT Output Tx signal 850 / 900 MHz 10 GND Ground 11 GND Ground 12 GND Ground 13 NC No Connect 14 GND Ground 15 GND Ground 16 DCS_OUT Output Tx signal 1800 / 1900 MHz GROUND PAD Segmented Ground Pad is device underside Because of its sensitivity to moisture absorption, this device package is baked and vacuum–packed prior to shipment in accordance with IPC J–STD 033 guidelines. Instructions on the shipping container label are in accordance with IPC J–STD 020B regarding exposure to moisture after the container seal is broken. These instructions must be followed; otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly. SKY77336 is capable of withstanding an MSL3/260 °C solder reflow. Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. If the part is attached in a reflow oven, the temperature ramp rate should not exceed 3°C per second; maximum temperature should not exceed 260 °C. If the part is manually attached, precaution should be taken to insure that the part is not subjected to temperatures exceeding 260 °C for more than 10 seconds. For details on attachment techniques, precautions, and handling procedures recommended by Skyworks, please refer to Skyworks Application Note: PCB Design and SMT Assembly/Rework, Document Number 101752. Additional information on standard SMT reflow profiles can also be found in the JEDEC Standard J-STD–020. Production quantities of this product are shipped in the standard tape–and–reel format. For packaging details, refer to Skyworks Application Note: Tape and Reel Information – RF Modules, Document Number 101568. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 16 September 19, 2008 • Skyworks Proprietary and Confidential information. • Products and product information are subject to change without notice. • 200780E SKY77336 POWER AMPLIFIER MODULE FOR QUAD-BAND GSM / GPRS PRELIMINARY DATASHEET Electrostatic Discharge Sensitivity SKY77336 is a Class 1 device. ESD testing was performed in compliance with JEDEC standards JESD22–A114 (Human Body Model), JESD22–A115 (Machine Model), and JESD22–C101 (Charged Device Model). Various failure criteria can be utilized when performing ESD testing. Many vendors employ relaxed ESD failure standards, which fail devices only after “the pad fails the electrical specification limits” or “the pad becomes completely non– functional”. Skyworks’ most stringent criteria fail devices as soon as the pad begins to show any degradation on a curve tracer. To avoid ESD damage, both latent and visible, it is very important that the product assembly and test areas follow the Class 1 ESD handling precautions listed below. • Personnel Grounding - Wrist Straps - Conductive Smocks, Gloves and Finger Cots - Antistatic ID Badges • Facility - Relative Humidity Control and Air Ionizers - Dissipative Floors (less than 109 Ω to GND) • Protective Workstation - Dissipative Table Top - Protective Test Equipment (Properly Grounded) - Grounded Tip Soldering Irons - Solder Conductive Suckers - Static Sensors • Protective Packaging and Transportation - Bags and Pouches (Faraday Shield) - Protective Tote Boxes (Conductive Static Shielding) - Protective Trays - Grounded Carts - Protective Work Order Holders Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 200780E • Skyworks Proprietary and Confidential information. • Products and product information are subject to change without notice. • September 19, 2008 17 Ordering Information Model Number Manufacturing Part Number SKY77336 Product Revision Package Operating Temperature SKY77336 5 x 5 x 1.05 MCM–16 –25 °C to +85 °C Date Description Revision History Revision A November 12, 2007 Initial Release – Preliminary Information B March 13, 2008 Revise: Table 2, add Nominal column; Page 5, Table 5 (2 of 8), Forward Isolation, first row, Maximum Column: change –10 to –30 C May 28, 2008 Revise: Features (p1) Low profile 1.0 to 0.9 Add: GREEN tag (p1) D July 24, 2008 Revise: Figure 6 and Table 6, rename pad 13 from VCC_OUT to NC E September 19, 2008 Revise: Features (p1) Low profile 0.9 mm to 1.15 mm Max.; Tables 2, 5-11; Figure 4 References Skyworks Application Note: PCB Design and SMT Assembly/Rework, Document Number 101752. Skyworks Application Note: Tape and Reel, Information – RF Modules Document Number 101568 Standard SMT Reflow Profiles: JEDEC Standard J-STD-020 Electrostatic Discharge Sensitivity (ESD) Testing: JEDEC Standard, JESD22-A114 Human Body Model (HBM) Electrostatic Discharge Sensitivity (ESD) Testing: JEDEC Standard, JESD22-A115 Machine Model (MM) Electrostatic Discharge Sensitivity (ESD) Testing: JEDEC Standard, JESD22-C101 (Charged Device Model) Copyright © 2007–2008, Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks, the Skyworks symbol, “Breakthrough Simplicity,” DCR, Helios, HIP3, Innovation to Go, Intera, iPAC, LIPA, Polar Loop, and System Smart are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference.