PRELIMINARY DATA SHEET SKY85803: Dual-Band 802.11a/b/g/n/ac WLAN Front-End Module Applications • 802.11b DSSS WLAN • 802.11a/g OFDM WLAN • 802.11n/ac WLAN • Access points, PCMCIA, PC cards Features • All RF ports matched to 50 Ω • Integrated 2.4 GHz PA, 5 GHz PA, transmit filter, transmit/receive switches, and diplexers • Integrated power detector for each transmit chain • Power: − +21 dBm, 802.11b, 11 Mbps, ACPR = +35 dBc − +18 dBm @ 3.0% EVM, 802.11n, 64 QAM, 2G − +16 dBm @ 3.0% EVM, 802.11n, 64 QAM, 5G − +16 dBm @ 1.8% EVM, 802.11ac, 256 QAM, 2G − +13 dBm @ 1.8% EVM, 802.11ac, 256 QAM, 5G − Single supply voltage: 3.3 V ± 10% • Small LGA (24-pin, 4 x 4 mm) package (MSL3, 250 °C per JEDEC J-STD-020) Figure 1. SKY85803 Block Diagram Designed for ease of use, all RF ports are matched to 50 Ω to simplify PCB layout and the interface to the transceiver. The device also includes a transmitter power detector with 20 dB of dynamic range for each transmit chain. Each PA has a separate digital enable control for transmitter on/off control. The power ramp rise/fall time is < 0.4 μs. The SKY85803 also provides a notch filter from 3.260 to 3.267 GHz and 3.28 to 3.89 GHz before the input of each 2.4 GHz and 5.0 GHz PA, respectively. Description The SKY85803 is a complete 802.11a/b/g/n/ac WLAN RF FrontEnd Module (FEM) that provides all the functionality of the Power Amplifiers (PAs), filtering, power detector, transmit/receive (T/R) switch, diplexers, and associated matching. The device provides a complete 2.4 GHz and 5.0 GHz WLAN RF solution from the output of the transceiver to the antenna in an ultra-compact form factor. The SKY85803 delivers < 2% EVM at rated AC power, which meets the stringent linearity conditions of the 802.11ac standard. The SKY85803 is manufactured in a compact, 4 x 4 mm, 24-pin Land Grid Array (LGA) package. A functional block diagram is shown in Figure 1. The pin configuration and package are shown in Figure 2. Signal pin assignments and functional pin descriptions are provided in Table 1. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 201849A • Skyworks Proprietary and Confidential Information • Products and Product Information are Subject to Change Without Notice • May 14, 2012 1 PRELIMINARY DATA SHEET • SKY85803 DUAL-BAND 802.11a/b/g/n/ac WLAN FEM Figure 2. SKY85803 Pinout – 24-Pin LGA (Top View) Table 1. SKY85803 Signal Descriptions Pin # Name Description Pin # Name Description 1 ENG 2.4 GHz PA enable 13 TG 2.0 GHz transmit RF input 2 GND Ground 14 GND Ground 3 GND Ground 15 RG 2.0 GHz receive RF output 4 ANT Antenna 16 RA 5.0 GHz receive RF output 5 GND Ground 17 GND Ground 6 C1 Switch control logic 1 18 TA 5.0 GHz transmit RF input 7 C0 Switch control logic 0 19 ENA 5.0 GHz PA enable 8 GND Ground 20 VCC3 Supply voltage 9 VCC1 Supply voltage 21 VCC4 Supply voltage 10 VCC2 Supply voltage 22 DET 2.0/5.0 GHz power detector output 11 GND Ground 23 GND Ground 12 GND Ground 24 GND Ground Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 2 May 14, 2012 • Skyworks Proprietary and Confidential Information • Products and Product Information are Subject to Change Without Notice • 201849A PRELIMINARY DATA SHEET • SKY85803 DUAL-BAND 802.11a/b/g/n/ac WLAN FEM Table 2. SKY85803 Absolute Maximum Ratings Parameter Supply voltage Symbol Minimum Maximum Units –0.3 +3.6 V –0.3 +3.6 V +12 dBm VCC PA enable voltage (pins ENA and ENG) Maximum input power to TA and TG pins with ANT terminated in 6:1 load or better PIN Operating temperature TA –40 +85 °C Storage temperature TSTG –40 +150 °C Switch logic control C0, C1 0 3.6 V LNA power (receive mode) PRX –3 dBm Note: Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other parameters set at or below their nominal value. Exceeding any of the limits listed here may result in permanent damage to the device. CAUTION: Although this device is designed to be as robust as possible, Electrostatic Discharge (ESD) can damage this device. This device must be protected at all times from ESD. Static charges may easily produce potentials of several kilovolts on the human body or equipment, which can discharge without detection. Industry-standard ESD precautions should be used at all times. The SKY85803 ESD threshold level is 1 kV (ANT pin zap to ground) and 250 V (all other pins). Table 3. SKY85803 Recommended Operating Conditions Parameter Symbol Minimum Typical Maximum Units Supply voltage VCC 3.0 3.3 3.6 V Operating temperature TA –40 +25 +85 °C Electrical and Mechanical Specifications The absolute maximum ratings of the SKY85803 are provided in Table 2. The recommended operating conditions are specified in Table 3 and electrical specifications are provided in Tables 4 through 12. Typical performance characteristics of the SKY85803 are illustrated in Figures 3 and 4. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 201849A • Skyworks Proprietary and Confidential Information • Products and Product Information are Subject to Change Without Notice • May 14, 2012 3 PRELIMINARY DATA SHEET • SKY85803 DUAL-BAND 802.11a/b/g/n/ac WLAN FEM Table 4. SKY85803 Electrical Specifications: DC Characteristics (Note 1) (VCC = 3.3 V, TA = +25 °C, All Unused Ports Terminated with 50 Ω, Unless Otherwise Noted) Parameter Total 802.11a transmit supply current Total 802.11g transmit supply current Symbol Test Condition Min Typical Max Units ICQ_A No RF 165 ICC_A POUT = +16 dBm, 54 Mbps, OFDM signal, 64 QAM 220 ICQ_G No RF 135 ICC_G POUT = +18 dBm, 54 Mbps, OFDM signal, 64 QAM 185 200 mA mA 250 mA mA Total 802.11b transmit supply current ICC_B POUT = +21 dBm, 11 Mbps, CCK signal, BT = 0.45 205 220 mA Total 802.11ac transmit supply current, 2G ICC_AC2G POUT = +16 dBm, 256 QAM, MCS9, 40 MHz 155 165 mA Total 802.11ac transmit supply current, 5G ICC_AC5G POUT = +13 dBm, 256 QAM, MCS9, 80 MHz 190 210 mA Total receive supply current, 2G ICC_RX2 ENG = ENA = 0 V, LNA on, switch condition 1 12 mA Total receive supply current, 5G ICC_RX5 ENG = ENA = 0 V, LNA on, switch condition 4 12 mA Total supply current ICC_OFF No RF, ENG = ENA = 0 V, switch condition 3 or 6 65 200 μA Typical Max Units Note 1: Performance is guaranteed only under the conditions listed in this Table. Table 5. SKY85803 Electrical Specifications: Logic Characteristics (Note 1) (VCC = 3.3 V, TA = +25 °C, All Unused Ports Terminated with 50 Ω, Unless Otherwise Noted) Parameter Symbol Test Condition Min Logic high voltage for ENG and ENA (module on) VENH 1.8 VCC V Logic low voltage for ENG and ENA (module off) VENL 0 0.5 V Input current logic high voltage (ENG and ENA) IENH 350 400 μA Input current logic low voltage (ENG and ENA) IENL 0.2 Note 1: Performance is guaranteed only under the conditions listed in this Table. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 4 May 14, 2012 • Skyworks Proprietary and Confidential Information • Products and Product Information are Subject to Change Without Notice • 201849A μA PRELIMINARY DATA SHEET • SKY85803 DUAL-BAND 802.11a/b/g/n/ac WLAN FEM Table 6. SKY85803 Electrical Specifications: Switch Characteristics (Note 1) (VCC = VEN = 3.3 V, TA = +25 °C, All Unused Ports Terminated with 50 Ω, Unless Otherwise Noted) Parameter Symbol Test Condition Min Typical Max Units Control voltage (on state) VCTL_ON 3.0 3.6 V Control voltage (off state) VCTL_OFF 0 0.2 V Low loss switch control voltage SWON High state = VCTL_ON – VCTL_OFF 2.8 VCC V High loss switch control voltage SWOFF Low state = VCTL_OFF – VCTL_OFF 0 0.3 V Switch control bias current RF applied No RF ICTL_ON C0 and C1 pins driven high 100 30 μA μA Control input capacitance CCTL 100 pF Note 1: Performance is guaranteed only under the conditions listed in this Table. Table 7. SKY85803 Electrical Specifications: 2.4 GHz Transmit Characteristics (1 of 2) (Note 1) (VCC = ENG = C0 = 3.3 V, ENA = C1 = 0 V, TA = +25 °C, All Unused Ports Terminated with 50 Ω, Unless Otherwise Noted) Parameter Symbol Test Condition Frequency range f Output power, 802.11g POUT_802.11G 54 Mbps OFDM signal, 64 QAM, DEVM = 3%, input signal EVM < 1%, 802.11g mask compliant Output power, 802.11n POUT_802.11N Output power, 802.11ac POUT_802.11AC Min Typical 2400 Max Units 2500 MHz +18 dBm OFDM signal, MCS7, HT40, DEVM = 3%, 802.11n mask compliant, ±11 MHz offset, RBW = 100 kHz, VBW = 30 kHz +18 dBm DEVM = 2% +17 dBm 40 MHz, 256 QAM, MCS9, DEVM = 1.8%, 802.11ac mask compliant +16 dBm DEVM = 1.2% +15 dBm 11 Mbps CCK signal, BT = 0.45, ACPR (±11 MHz offset) < –35, ACPR (±22 MHz offset) < –56 +21 Output power, 802.11b POUT_802.11B 1 dB compression point P1dB +24.0 Small signal gain |S21| 25 Small signal gain variation over band Δ|S21| Small signal gain @ ½ VCO frequency |S21|_1.6 1640 to 1942 MHz Small signal gain @ VCO frequency |S21|_3.2 3216 to 3312 MHz +22 +24.5 dBm dBm 30 dB 1 2 dB 12 20 dB 0 dB Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 201849A • Skyworks Proprietary and Confidential Information • Products and Product Information are Subject to Change Without Notice • May 14, 2012 5 PRELIMINARY DATA SHEET • SKY85803 DUAL-BAND 802.11a/b/g/n/ac WLAN FEM Table 7. SKY85803 Electrical Specifications: 2.4 GHz Transmit Characteristics (2 of 2) (Note 1) (VCC = ENG = C0 = 3.3 V, ENA = C1 = 0 V, TA = +25 °C, All Unused Ports Terminated with 50 Ω, Unless Otherwise Noted) Parameter nd rd 2 and 3 harmonics Symbol 2fo, 3fo Test Condition Max Units POUT ≤ +21 dBm, 1 Mbps, CCK –40 dBm/MHz POUT ≤ +18 dBm, 802.11g/n, all data rates –50 dBm/MHz 0.4 μs Delay and rise/fall time tDR, tDF Input return loss |S11| Stability STAB CW, POUT = +21 dBm, 0.1 to 21 GHz, load VSWR = 6:1 Ruggedness Ru TG = +12 dBm, ANT load varies over 6:1 VSWR Min 50% of VEN edge and 90/10% of final output power level Typical 0.2 9 10 dB All non-harmonically related outputs <–42 dBm/MHz – No irreversible damage – Note 1: Performance is guaranteed only under the conditions listed in this Table. Table 8. SKY85803 Electrical Specifications: 2.4 GHz Receive Characteristics (Note 1) (VCC = 3.3 V, Switch Condition 1, TA = +25 °C, All Unused Ports Terminated with 50 Ω, Unless Otherwise Noted) Parameter Symbol Test Condition Min Typical 2400 Max Units 2500 MHz 16 dB –10 dB Frequency range f Small signal gain, LNA enabled S21 2400 to 2485 MHz 10 Small signal gain, bypass mode S21 LNA bypassed, switch condition 3 –12 Small signal gain, high band gain @ 5150 to 5850 MHz S21 Small signal gain variation Δ|S21| 2400 to 2485 MHz, over any 40 MHz band 0.25 0.50 dB Noise Figure NF De-embedded to device 2.5 2.8 dB Input return loss |S11| 1 dB input compression point IP1dB 14 –10 5 dB 10 dB LNA enabled –7 dBm LNA bypassed, switch condition 3 +8 dBm 40 dB Loopback isolation (ANT to RG pins) LB Switch condition 2, POUT = PSAT Enable time tEN 10% to 90% of receive RF power from time that C0 signal is at 50% PSAT + 10 0.2 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 6 May 14, 2012 • Skyworks Proprietary and Confidential Information • Products and Product Information are Subject to Change Without Notice • 201849A μs PRELIMINARY DATA SHEET • SKY85803 DUAL-BAND 802.11a/b/g/n/ac WLAN FEM Table 9. SKY85803 Electrical Specifications: 5.0 GHz Transmit Characteristics (Note 1) (VCC = ENA = C0 = 3.3 V, ENG = C1 = 0 V, TA = +25 °C, All Unused Ports Terminated with 50 Ω, Unless Otherwise Noted) Parameter Symbol Frequency range f Output power, 802.11n POUT_802.11N Output power, 802.11ac POUT_802.11AC Test Condition Min Typical 4900 Max Units 5900 MHz OFDM signal, MCS7, HT40, DEVM = 3%, 802.11n mask compliant, ±11 MHz offset, RBW = 100 kHz, VBW = 30 kHz +16 dBm DEVM = 2% +15 dBm 80 MHz, 256 QAM, MCS9, DEVM = 1.8%, input signal EVM < 0.6%, 802.11ac mask compliant +13 dBm DEVM = 1.2% 1 dB compression point P1dB +21.0 Small signal gain S21 Small signal gain variation over 80 MHz channel Δ|S21| Small signal gain variation over sub-bands Δ|S21| 4.90 to 5.18 GHz, 5.18 to 5.50 GHz, 5.50 to 5.90 GHz Isolation S12 2nd and 3rd harmonics In band @ 1.9 GHz @ 3.9 GHz +12 dBm +22.5 dBm +23 +30 –20 +4 dB dB dB –1 +1 dB 3 dB Switch state 5, 4.9 to 5.9 GHz –45 dB 2fo, 3fo @ +16 dBm, 54 Mbps, 802.11a –50 dBm/MHz Delay and rise/fall time tDR, tDF 50% of VEN edge and 90/10% of final output power level 0.4 μs Input return loss |S11| Output return loss |S22| Stability STAB 64 QAM, POUT = +16 dBm, 0.1 to 21 GHz, load VSWR = 6:1 Ruggedness Ru TA = +12 dBm, ANT load varies over 6:1 VSWR No irreversible damage – 2 0.2 10 dB 10 dB All non-harmonically related outputs <–42 dBm/MHz – Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 201849A • Skyworks Proprietary and Confidential Information • Products and Product Information are Subject to Change Without Notice • May 14, 2012 7 PRELIMINARY DATA SHEET • SKY85803 DUAL-BAND 802.11a/b/g/n/ac WLAN FEM Table 10. SKY85803 Electrical Specifications: 5.0 GHz Receive Characteristics (Note 1) (VCC = 3.3 V, Switch Condition 4, TA = +25 °C, All Unused Ports Terminated with 50 Ω, Unless Otherwise Noted) Parameter Symbol Test Condition Min Frequency range f Small signal gain S21 4900 to 5850 MHz 10 Small signal gain, bypass mode S21 LNA bypassed, switch condition 6 –14 Small signal gain, low band gain @ 2400 to 2500 MHz S21 Small signal gain variation Δ|S21| 4900 to 5850 MHz, over any 80 MHz band Noise Figure NF De-embedded to device Input return loss |S21| Output return loss |S22| 1 dB input compression point IP1dB Typical 4900 12 Max Units 5850 MHz 14 dB –10 dB –10 –0.5 2.8 8 10 6 10 dB +0.5 dB 3.0 dB dB dB LNA enabled –6 dBm LNA bypassed, switch condition 6 +6 dBm Loopback isolation (TA to RA pins) LB Switch condition 5, POUT = PSAT Enable time tEN 10% to 90% of receive RF power from time that C0 signal is at 50% –40 dB 0.2 μs Table 11. SKY85803 Electrical Specifications: 2.0 GHz Power Detector Characteristics (Note 1) (VCC = 3.3 V, Switch Condition 2, TA = +25 °C, All Unused Ports Terminated with 50 Ω, Unless Otherwise Noted) Parameter Symbol Test Condition Max Units 2400 Min Typical 2500 MHz 0 +22 dBm Frequency range f Power detector range, peak power PDR DC output impedance PDZOUT 2.3 kΩ Output voltage @ POUT = +21 dBm PDVP21 Measured into 26.5 kΩ 0.80 V Output voltage @ POUT = +18 dBm PDVP18 Measured into 26.5 kΩ 0.60 V Output voltage, no RF output power PDVPNORF Measured into 26.5 kΩ Power detector low-pass filter –3 dB corner frequency LPF-3DB Measured into 26.5 kΩ Power detector accuracy PDETACC Measured into 3:1 load at ANT port Measured at ANT pin 0.20 V 70 –1.5 MHz +1.5 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 8 May 14, 2012 • Skyworks Proprietary and Confidential Information • Products and Product Information are Subject to Change Without Notice • 201849A dB PRELIMINARY DATA SHEET • SKY85803 DUAL-BAND 802.11a/b/g/n/ac WLAN FEM Table 12. SKY85803 Electrical Specifications: 5.0 GHz Power Detector Characteristics (Note 1) (VCC = 3.3 V, Switch Condition 5, TA = +25 °C, All Unused Ports Terminated with 50 Ω, Unless Otherwise Noted) Parameter Symbol Frequency range f Power detector range, peak power PDR DC output impedance PDZOUT Output voltage @ POUT = +18 dBm PDVP18 Output voltage @ POUT = +16 dBm PDVP21 Output voltage, no RF output power Test Condition Measured at ANT pin Min Typical Max Units 4900 5900 MHz 0 +21 dBm 26.5 kΩ Measured into 26.5 kΩ 0.70 V Measured into 26.5 kΩ 0.60 V PDVPNORF Measured into 26.5 kΩ 0.20 V Power detector low-pass filter –3 dB corner frequency LPF-3DB Measured into 26.5 kΩ 70 Power detector accuracy PDETACC Measured into 3:1 load at ANT port –2 MHz +2 dB Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 201849A • Skyworks Proprietary and Confidential Information • Products and Product Information are Subject to Change Without Notice • May 14, 2012 9 PRELIMINARY DATA SHEET • SKY85803 DUAL-BAND 802.11a/b/g/n/ac WLAN FEM Typical Performance Characteristics Figure 3. Power Detector vs Output Power Over Frequency @ 2.5 GHz Figure 4. Power Detector vs Output Power Over Frequency @ 5.0 GHz Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 10 May 14, 2012 • Skyworks Proprietary and Confidential Information • Products and Product Information are Subject to Change Without Notice • 201849A PRELIMINARY DATA SHEET • SKY85803 DUAL-BAND 802.11a/b/g/n/ac WLAN FEM Evaluation Board Description Package and Handling Information The SKY85803 Evaluation Board is used to test the performance of the SKY85803 WLAN FEM. An Evaluation Board schematic diagram is provided in Figure 5. A photograph of the Evaluation Board is shown in Figure 6. Component values for the SKY85803 Evaluation Board are listed in Table 14. Since the device package is sensitive to moisture absorption, it is baked and vacuum packed before shipping. Instructions on the shipping container label regarding exposure to moisture after the container seal is broken must be followed. Otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly. Evaluation Board Setup Procedure THE SKY85803 is rated to Moisture Sensitivity Level 3 (MSL3) at 250 °C. It can be used for lead or lead-free soldering. For additional information, refer to the Skyworks Application Note, Solder Reflow Information, document number 200164. Step 1: Connect system ground to pin 2 of connector J6. Step 2: Apply 3.3 V to pin 1 of connector J6. Step 3: Select a path according to the logic shown in Table 13. Package Dimensions The PCB layout footprint for the SKY85803 is provided in Figure 7. Typical case markings are shown in Figure 8. Package dimensions for the 24-pin LGA are shown in Figure 9, and tape and reel dimensions are provided in Figure 10. Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. Production quantities of this product are shipped in a standard tape and reel format. Table 13. SKY85803 Evaluation Board Switch Control Logic Logic State Condition C0 (Pin 1, J16 Header) C1 (Pin 5, J16 Header) ENA (Pin 7, J7 Header) ENG (Pin 3, J7 Header) SP3T LNA Bypass 1 0 1 0 0 RG RG enable Open 2 0 0 0 1 TG RG off RG bypass 3 0 0 0 0 RG RG off RG bypass 4 1 1 0 0 RA RA enable Open 5 1 0 1 0 TA RA off RA bypass 6 1 0 0 0 RA RA off RA bypass Note: “0” = 0 V. “1” = +3.3 V. Any state other than described in this Table places the switch into an undefined state. An undefined state will not damage the device. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 201849A • Skyworks Proprietary and Confidential Information • Products and Product Information are Subject to Change Without Notice • May 14, 2012 11 PRELIMINARY DATA SHEET • SKY85803 DUAL-BAND 802.11a/b/g/n/ac WLAN FEM Figure 5. SKY85803 Evaluation Board Schematic Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 12 May 14, 2012 • Skyworks Proprietary and Confidential Information • Products and Product Information are Subject to Change Without Notice • 201849A PRELIMINARY DATA SHEET • SKY85803 DUAL-BAND 802.11a/b/g/n/ac WLAN FEM Figure 6. SKY85803 Evaluation Board Photo Table 14. SKY85803 Evaluation Board Bill of Materials Component Size Value Vendor Part # Comments C4 0402 220 pF Murata GRM1555C1H221JA01 Multilayer ceramic C5, C6 0402 10 pF Murata GRM1555C1H100JZ01 Multilayer ceramic C8 0805 2.2 μF Murata GRM21BR71A225KA01L Ceramic capacitor, 10 V, 10% X7R Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 201849A • Skyworks Proprietary and Confidential Information • Products and Product Information are Subject to Change Without Notice • May 14, 2012 13 PRELIMINARY DATA SHEET • SKY85803 DUAL-BAND 802.11a/b/g/n/ac WLAN FEM Figure 7. SKY85803 PCB Layout Footprint Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 14 May 14, 2012 • Skyworks Proprietary and Confidential Information • Products and Product Information are Subject to Change Without Notice • 201849A PRELIMINARY DATA SHEET • SKY85803 DUAL-BAND 802.11a/b/g/n/ac WLAN FEM *** TBD *** Figure 8. Typical Case Markings (Top View) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 201849A • Skyworks Proprietary and Confidential Information • Products and Product Information are Subject to Change Without Notice • May 14, 2012 15 PRELIMINARY DATA SHEET • SKY85803 DUAL-BAND 802.11a/b/g/n/ac WLAN FEM Figure 9. SKY85803 24-Pin LGA Package Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 16 May 14, 2012 • Skyworks Proprietary and Confidential Information • Products and Product Information are Subject to Change Without Notice • 201849A PRELIMINARY DATA SHEET • SKY85803 DUAL-BAND 802.11a/b/g/n/ac WLAN FEM Figure 10. SKY85803 Tape and Reel Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 201849A • Skyworks Proprietary and Confidential Information • Products and Product Information are Subject to Change Without Notice • May 14, 2012 17 PRELIMINARY DATA SHEET • SKY85803 DUAL-BAND 802.11a/b/g/n/ac WLAN FEM Ordering Information Model Name SKY85803 WLAN FEM Manufacturing Part Number SKY85803 Evaluation Board Part Number SKY85803-EVB Copyright © 2012 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks, the Skyworks symbol, and “Breakthrough Simplicity” are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 18 May 14, 2012 • Skyworks Proprietary and Confidential Information • Products and Product Information are Subject to Change Without Notice • 201849A