PRELIMINARY DATA SHEET SKY73022: 700 – 1000 MHz High Gain and Linearity Diversity Downconversion Mixer for 2G/3G Base Station Transceiver Applications Applications Description • 2G/3G base station transceivers: − GSM/EDGE, CDMA, UMTS/WCDMA, iDEN The SKY73022 is a fully integrated diversity mixer that includes Local Oscillator (LO) drivers, an LO switch, high linearity mixers, and large dynamic range Intermediate Frequency (IF) amplifiers. Low loss RF baluns have also been included to reduce design complications and lower system cost. • Small, MCM (36-pin, 6 x 6 mm) Pb-free package (MSL3, 260 °C per JEDEC J-STD-020) Skyworks offers lead (Pb)-free RoHS (Restriction of Hazardous Substances) compliant packaging. VCC_LO The SKY73022 is manufactured using a robust silicon BiCMOS process and has been designed for optimum long-term reliability. The SKY73022 diversity downconversion mixer is provided in a compact, 36-pin 6 x 6 mm Multi-Chip Module (MCM). A functional block diagram is shown in Figure 1. The pin configuration and package are shown in Figure 2. Signal pin assignments and functional pin descriptions are provided in Table 1. VCC_IFA • Operating frequency range: 700 to 1000 MHz • IF frequency range: 40 to 300 MHz • Conversion gain: 9.0 dB • Input IP3: 26.5 dBm • Output IP3: 35.5 dBm • Noise figure: 9.8 dB • Integrated LO drivers • Integrated low loss RF baluns • High linearity IF amplifiers • On-chip SPDT LO switch (greater than 55 dB LO-to-LO isolation) IFA+ IFA– Features The SKY73022 features an input IP3 of 26.5 dBm and a Noise Figure (NF) of 9.8 dB, making the device an ideal solution for high dynamic range systems such as 2G/3G base station receivers. The LO switch provides more than 55 dB of isolation between LO inputs and supports the switching time required for GSM/EDGE base stations. RIFA • Land mobile radio • ISM band transceivers • High performance radio links • RF identification RFA LO1 LO2 RFB VCC_IFB IFB+ IFB– RIFB LO_SEL VCC_LO S643 Figure 1. SKY73022 Block Diagram Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 200518A • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • February 13, 2007 1 VCC_RFA NC GND IFA– IFA+ NC VCC_IFA RIFA NC PRELIMINARY DATA SHEET • SKY73022 DOWNCONVERSION MIXER 36 35 34 33 32 31 30 29 28 3 25 GND VCC_LO 4 24 GND GND 5 23 LO_SEL VCC_LO 6 22 GND GND 7 21 VCC_LO NC 8 20 GND RFB 9 19 LO1 10 11 12 13 14 15 16 17 18 NC GND RIFB GND VCC_IFB 26 NC 2 IFB– NC IFB+ LO2 GND 27 NC 1 VCC_RFB RFA S646 Figure 2. SKY73022 Pinout – 36-Pin MCM Table 1. SKY73022 Signal Descriptions Pin # 1 Name RFA Description Channel A RF input Pin # 19 Name LO1 Description Local oscillator 1 input 2 NC No connect 20 GND Ground 3 GND Ground 21 VCC_LO DC supply, +5 V 4 VCC_LO DC supply, +5 V 22 GND Ground 5 GND Ground 23 LO_SEL Local oscillator select switch control 6 VCC_LO DC supply, +5 V 24 GND Ground 7 GND Ground 25 GND Ground 8 NC No connect 26 GND Ground 9 RFB Channel B RF input 27 LO2 Local oscillator 2 input 10 VCC_RFB Channel B RF DC supply, +5 V 28 NC No connect 11 NC No connect 29 RIFA Channel A IF bias adjust 12 GND Ground 30 VCC_IFA Channel A IF DC supply, +5 V 13 IFB+ Positive channel B IF output 31 NC No connect 14 IFB– Negative channel B IF output 32 IFA+ Positive channel A IF output 15 NC No connect 33 IFA– Negative channel A IF output 16 VCC_IFB Channel B IF DC supply, +5 V 34 GND Ground 17 RIFB Channel B IF bias adjust 35 NC No connect 18 NC No connect 36 VCC_RFA Channel A RF DC supply, +5 V Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 2 February 13, 2007 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 200518A PRELIMINARY DATA SHEET • SKY73022 DOWNCONVERSION MIXER Functional Description A high isolation SPDT switch allows the SKY73022 to be used for frequency hopping applications. This switch provides greater than 55 dB of LO1 to LO2 isolation: The SKY73022 is a high gain diversity mixer, optimized for base station receiver applications. The device consists of two diversity channels (A and B), each consisting of a low loss RF balun, high linearity passive mixer, and a low noise IF amplifier. LO_SEL Input LO Path Selected High LO1 (pin 19) enabled Low LO2 (pin 27) enabled Two LO amplifiers (independent of channels A and B) are also included that allow the SKY73022 to connect directly to the output of a Voltage Controlled Oscillator (VCO). This eliminates the extra gain stages needed by most discrete passive mixers. A Single Pole, Double Throw (SPDT) switch has been included to select between two different LO inputs for frequency hopping applications (i.e., GSM). For applications that do not require frequency hopping, LO_SEL is fixed to one state and the appropriate LO input is used. An internal pull-down resistor enables the LO2 input. RF Baluns and Passive Mixer IF Amplifier The RF baluns provide a single ended input, which can easily be matched to 50 Ω using a simple external matching circuit. The RF baluns offer very low loss, and excellent amplitude and phase balance. The SKY73022 includes high dynamic range IF amplifiers that follow the passive mixers in the signal path. The outputs require a supply voltage connection using inductive chokes. These choke inductors should be high-Q and have the ability to handle 200 mA or greater. The high linearity SKY73022 is a passive, double balanced mixer that provides a very low conversion loss, and excellent 3rd Order Input Insertion Point (IIP3). A simple matching network allows the output ports to be matched to a balanced 200 Ω impedance. The IF amplifiers are optimized for IF frequencies between 40 and 300 MHz. The IF amplifiers can be operated outside of this range, but with a slight degradation in performance. Addtionally, the balanced nature of the mixer provides for high port-to-port isolation. LO Buffers and SPDT LO Switch Electrical and Mechanical Specifications The LO buffers allow the input power of the SKY73022 to be in the range of ±3 dBm. The LO section is optimized for low-side LO injection. However, each of the two LOs can be driven over a wide frequency range with only slight degradation in performance. The absolute maximum ratings of the SKY73022 are provided in Table 2 and the recommended operating conditions in Table 3. Electrical characteristics for the SKY73022 are provided in Table 4. Table 2. SKY73022 Absolute Maximum Ratings Parameter Symbol Supply voltage, +5 V (VCC1 – VCC7) VCC Supply current ICC RF input power PRF LO input power PLO Minimum Typical Maximum Units 4.5 5.0 5.5 V 380 420 mA 0 20 dBm 6 dBm Operating case temperature TC –40 +85 °C Storage case temperature TSTG –40 +125 °C Note: Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other parameters set at or below their nominal value. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 200518A • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • February 13, 2007 3 PRELIMINARY DATA SHEET • SKY73021 DOWNCONVERSION MIXER Table 3. SKY73022 Recommended Operating Conditions Parameter Symbol Minimum Typical Maximum Units 4.75 5.00 5.25 V +3 dBm 0.8 V V Supply voltage, +5 V (VCC1 – VCC7) VCC Supply current ICC LO input power PLO –3 LO select input: high low LO_SELH LO_SELL 2.2 Operating case temperature TC –40 +85 °C RF frequency range FRF 700 1000 MHz LO frequency range (Note 1) FLO 900 1250 MHz IF frequency range FIF 40 300 MHz 380 mA 0 Note 1: The SKY73022 has been optimized for low side LO injection. However, the LO can be used outside of the specified frequency range with degraded performance. Table 4. SKY73022 Electrical Specifications (1 of 2) (Voltage Supply = +5 V, TC = +25 °C, LO = 0 dBm, RF Frequency = 900 MHz, IF Frequency = 200 MHz, LO Frequency = 1100 MHz, Unless Otherwise Noted) Parameter Conversion gain Symbol Test Condition Min G Typical Max 9.0 dB Noise Figure NF 9.8 dB Noise Figure with a blocker signal NFBLK Blocking signal input power = +8 dBm 20.5 dB Third order input intercept point IIP3 Tone space = 800 kHz, input tone power = –10 dBm 26.5 dBm Third order output intercept point OIP3 Tone space = 800 kHz, input tone power = –10 dBm 35.5 dBm 2RF – 2LO 2x2 PRF = –10 dBm –70 dBc 3RF – 3LO 3x3 PRF = –10 dBm –80 dBc Input 1 dB compression point IP1dB 13.5 dBm Output 1 dB compression point OP1dB 21.5 dBm LO1-to-LO2 isolation 55 dB Channel-to-channel isolation 50 dB RF to IF isolation 55 dB LO leakage: @ RF port @ IF port –44 –44 dBm dBm LO_SEL input –20 LO switching time +150 +250 µA 0.5 µs Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 4 Units February 13, 2007 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 200518A PRELIMINARY DATA SHEET • SKY73021 DOWNCONVERSION MIXER Table 4. SKY73022 Electrical Specifications (2 of 2) (Voltage Supply = +5 V, TC = +25 °C, LO = 0 dBm, RF Frequency = 900 MHz, IF Frequency = 200 MHz, LO Frequency = 1100 MHz, Unless Otherwise Noted) Parameter Symbol Test Condition Min Typical Max Units RF port input return loss ZIN_RF With external matching components –14 dB LO port input return loss ZIN_LO With external matching components –14 dB IF port input return loss ZOUT_IF With external matching components –14 dB Evaluation Board Description The SKY73022 Evaluation Board is used to test the performance of the SKY73022 downconversion mixer. An assembly drawing for the Evaluation Board is shown in Figure 3 and the layer detail is provided in Figure 4. Circuit Design Configurations The following design considerations are general in nature and must be followed regardless of final use or configuration: 1. Paths to ground should be made as short and as low impedance as possible. 2. The ground pad of the SKY73022 provides critical electrical and thermal functionality. This pad is the main thermal conduit for heat dissipation. Since the circuit board acts as the heat sink, it must shunt as much heat as possible from the device. Therefore, design the connection to the ground pad to dissipate the maximum heat produced by the circuit board. For more information on soldering the SKY73022, refer to the Package and Handling Information section of this Data Sheet. 3. Skyworks recommends including external bypass capacitors on the VCC voltage inputs of the device. 4. Components L5, L6, L14, and L15 (see Figure 5) are high-Q, low loss inductors. These inductors must be able to pass currents in excess of 200 mA DC. 5. Components R1 and R2 (see Figure 5) allow for external adjustment of the IF amplifier bias points. For operation as specified in Tables 3 and 4, these resistors are not required. A schematic diagram for the SKY73022 Evaluation Board is shown in Figure 5. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 200518A • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • February 13, 2007 5 PRELIMINARY DATA SHEET • SKY73022 DOWNCONVERSION MIXER J9 J5 C34 C35 L17 L16 J4 C2 L12 L13 R4 C25 T2 C32 L1 C28 C29 J8 C33 C39 C26 L2 L14 L15 C38 C3 L11 R2 C27 C1 R5 C23 C22 C20 C4 J1 C24 C21 J2 C5 C17 C8 C7 C41 C6 L5 C14 L6 R6 R1 C40 L4 C13 C12 L3 J7 T1 C18 L10 C11 C19 R3 L18 C36 J10 L8 L19 C37 C15 J3 L9 C16 J6 S905 Figure 3. SKY73022 Evaluation Board Assembly Diagram Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 6 February 13, 2007 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 200518A PRELIMINARY DATA SHEET • SKY73022 DOWNCONVERSION MIXER Layer 1: Top -- Metal Layer 2: Ground Layer 3: Power Plane Layer 4: Solid Ground Plane S904 Figure 4. SKY77022 Evaluation Board Layer Detail Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 200518A • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • February 13, 2007 7 PRELIMINARY DATA SHEET • SKY73022 DOWNCONVERSION MIXER L17 DNI L14 470 nH C35 DNI R4 0Ω DB714 C32 DNI L13 8.2 nH C29 DNI C27 33 pF C33 DNI C2 DNI x 29 LO2 NC GND GND GND VCC_LO NC 11 12 13 14 15 x 10 16 17 23 C25 DNI VCC J2 C21 33 pF 22 21 20 L10 0Ω 19 C17 33 pF NC RIFB LO1 C22 12 pF 18 C18 DNI C20 1 μF J3 C19 DNI R1 DNI x RFB GND VCC_IFB 9 GND NC 8 GND IFB– C7 1.5 pF x VCC_LO x C6 DNI C8 0Ω LO_SEL IFB+ L4 18 nH L3 0Ω GND GND 7 C24 DNI Element Jumper GND NC 6 C23 33 pF 24 VCC_RFB 5 J8 25 VCC_LO C5 33 pF 27 26 2 3 C4 DNI L11 0Ω 28 NC NC 30 RIFA 31 IFA+ 32 IFA– NC 33 4 VCC J7 RFA 34 VCC_IFA C3 1.5 pF 1 35 GND C1 0Ω VCC_RFA L2 18 nH R2 DNI x L1 0Ω J5 C26 1 μF x x 36 J4 L12 0Ω C28 22 pF R5 DNI VCC J9 C34 DNI T2 L15 470 nH VCC L16 DNI VCC L5 470 nH C14 33 pF C13 1 μF R6 DNI VCC C12 DNI C11 DNI L6 470 nH T1 C15 DNI DB714 Note: The Evaluation Board can be converted to provide a differential output by removing components T1, T2, R3, and R4. R3 0Ω L8 8.2 nH J6 L18 DNI J10 C16 22 pF L19 DNI C37 DNI L9 0Ω C36 DNI Figure 5. SKY73022 Evaluation Board Schematic Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 8 February 13, 2007 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 200518A S760_A PRELIMINARY DATA SHEET • SKY73022 DOWNCONVERSION MIXER Package Dimensions Figure 6 shows the package dimensions for the 36-pin MCM, and Figure 7 provides the tape and reel dimensions. Package and Handling Information Since the device package is sensitive to moisture absorption, it is baked and vacuum packed before shipping. Instructions on the shipping container label regarding exposure to moisture after the container seal is broken must be followed. Otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly. THE SKY73022 is rated to Moisture Sensitivity Level 3 (MSL3) at 260 °C. It can be used for lead or lead-free soldering. For additional information, refer to the Skyworks Application Note, PCB Design & SMT Assembly/Rework Guidelines for MCM-L Packages, document number 101752. Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. Production quantities of this product are shipped in a standard tape and reel format. For packaging details, refer to the Skyworks Application Note, Tape and Reel, document number 101568. Electrostatic Discharge (ESD) Sensitivity The SKY73022 is a static-sensitive electronic device. Do not operate or store near strong electrostatic fields. Take proper ESD precautions. 18X 2.9 Pin 1 Indicator C Pin 36 4X 2 B 6 Pin 1 Indicator (See Detail D) Pin 1 4X 1.5 4X 0.5 4X 1 A 4X 2 4X 1 4X 1.5 6 4X 0.5 2X 1.9 18X 2.9 A 1.1 ± 0.1 36x SMT Pad 0.15 A B C 3X R0.2 2X 1.9 0.1 0.15 A B C Top View Side View Bottom View Solder Mask Opening 0.2 A B C 0.5 ± 0.1 (0.2 x 0.2) (0.1) 0.25 ± 0.05 0.4 ± 0.05 Detail D Metal Pad Edge All measurements are in millimeters Detail A Pads are solder mask defined on one edge and metal defined on three edges. S689_A Dimensioning and tolerancing according to ASME Y14.5M-1994 Figure 6. SKY73022 36-Pin MCM Package Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 200518A • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • February 13, 2007 9 PRELIMINARY DATA SHEET • SKY73022 DOWNCONVERSION MIXER 2.00 ± 0.05 4.00 8.00 ∅1.55 ± 0.05 0.30 ± 0.05 B 5.50 ± 0.05 A 1.75 ± 0.10 6.30 A 5o Max. 12.00 ± 0.30 Pin #1 Indicator B ∅1.50 Min. 1.70 6.30 B 5o Max. Notes: 1. Carrier tape: black conductive polystyrene 2. Cover tape material: transparent conductive PSA 3. Cover tape size: 9.3 mm width 4. All dimensions are in millimeters A C1222 Figure 7. SKY73022 Tape and Reel Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 10 February 13, 2007 • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • 200518A PRELIMINARY DATA SHEET • SKY73022 DOWNCONVERSION MIXER Ordering Information Model Name SKY73022 700-1000 MHz Downconversion Mixer Manufacturing Part Number Evaluation Kit Part Number SKY73022-11 (Pb-free package) Copyright © 2007 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks, the Skyworks symbol, and “Breakthrough Simplicity” are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • [email protected] • www.skyworksinc.com 200518A • Skyworks Proprietary and Confidential information • Products and Product Information are Subject to Change Without Notice • February 13, 2007 11