MQME-28E-T6

MQME-28E-T6
Transient
Suppression Filter
HIGH RELIABILITY EMI FILTER
-40V to +70V
20A
60mΩ @ 125ºC
>80dB @ 500kHz
Continuous Input
Output Current
Max DC Resistance
Differential Attenuation
FULL POWER OPERATION: -55ºC to +125ºC
The MilQor® series of high-reliability EMI filters brings
SynQor’s field proven technology and manufacturing
expertise to the Military/Aerospace industry. SynQor’s
innovative QorSealTM packaging approach ensures
survivability in the most hostile environments. Compatible
with the industry standard format, these filters have high
MQ
B
Y-H
T6-
8E-
-2
ME
TER 0W
I FIL 0A 32
EM
2
28Vin
differential-mode and common-mode attenuation, low
DC resistance, and a stabilizing bulk capacitor resistor.
They follow conservative component derating guidelines
and they are designed and manufactured to comply with
a wide range of military standards.
Design Process
MQME series filters are:
• DesignedforreliabilityperNAVSO-P3641-Aguidelines
• Designedwithcomponentsderatedper:
—MIL-HDBK-1547A
—NAVSOP-3641A
Qualification Process
MQME series filters are qualified to:
• MIL-STD-810F
—consistentwithRTCA/DO-160E/F/G
• SynQor’sFirstArticleQualification
—consistentwithMIL-STD-883F
• SynQor’sLong-TermStorageSurvivabilityQualification
• SynQor’son-goinglifetest
In-Line Manufacturing Process
• AS9100andISO9001:2008certifiedfacility
• Fullcomponenttraceability
• Temperaturecycling
• Constantacceleration
• 24,96,160hourburn-in
• Threeleveltemperaturescreening
Product # MQME-28E-T6
Phone 1-888-567-9596
Features
•Transientsuppressioncircuitrytoblockvoltagesurges
and spikes
•Soft-Startcircuitrytolimitin-rushchargingcurrents
•Reversepolarityprotectionwithalowlosssynchronousrectifier
•Inputover-voltageshutdown
•Outputcurrentlimitforshort-circuitprotection
•Enablepass-throughcircuitry
•Standbycircuitrytominimizequiescentpowerdraw
•20Aoutputcurrent
•VerylowDCresistance
•>80dBdifferential-modeattenuationat500kHz
•>60dBcommon-modeattenuationat500kHz
•Stabilizingbulkcapacitoranddampingresistorincluded
•AllcapacitorsareX7Rmulti-layerceramic
•DesignedtomeetallMIL-STD461EMIandRTCA/D0-160E/
F/GSection22lightningrequirements(tolevel4)
Specification Compliance
MQME series filters (with MQFL converters) are designed to meet:
• MIL-HDBK-704-8(AthroughF)
• RTCA/DO-160E/F/GSection16
• MIL-STD-1275B/D
• DEF-STAN61-5(part6)/6
• MIL-STD-461(C,D,E,F)
• RTCA/DO-160E/F/GSection22
www.synqor.com
Doc.# 005-0006011 Rev. B
01/23/15
Page 1
MQME-28E-T6
Current: 20A
Technical Specification
BLOCK DIAGRAM
TRANSIENT
SUPPRESSION,
CURRENT LIMIT,
IOVSD, AND
SOFT-START
CIRCUITRY
POSITIVE
INPUT
PINS 1, 2, 3
POSITIVE
OUTPUT
SYNCHRONOUS
RECTIFIER AND
CONTROL
CIRCUITRY
PINS 10, 11, 12
RDAMPING
CBULK
PINS 5, 6
PIN 7
INPUT
RETURN
ANTI-PARALLEL
DIODE
OUTPUT
RETURN
PIN 8
STANDBY
CIRCUIT
STANDBY
PIN 9
PIN 4
ENABLE PASS-THROUGH
CIRCUITRY
ENABLE
OUTPUT
ENABLE
INPUT
TYPICAL CONNECTION DIAGRAM
+VIN
Open
means
“ON”
ENAIN
MQME EMI
FILTER
-VIN
+VOUT
+VIN
ENAOUT
ENA1
STDBY
-VOUT
+VOUT
MQFL DC-DC
CONVERTER
LOAD
OUT RTN
IN RTN
Closed
means
“ON”
+VIN
NOTE: Use of the enable pass-through
feature is optional. Pin 4 may be
connected to Pins 5 and 6. See
ENABLE Description in BASIC
OPERATION AND FEATURES.
ENA1
+VOUT
MQFL DC-DC
CONVERTER
IN RTN
LOAD
OUT RTN
TO OTHER LOADS
Product # MQME-28E-T6
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0006011 Rev. B
01/23/15
Page 2
MQME-28E-T6
Current: 20A
Technical Specification
MQME-28E-T6 ELECTRICAL CHARACTERISTICS
Parameter
Min.
Typ.
Max.
Units Notes & Conditions
Specifications subject to change without notice
Group A
Vin=28V DC ±5%, Pout=320W, unless otherwise specified
ABSOLUTE MAXIMUM RATINGS
Input Voltage
Continuous
Transient (≤ 1 s)
Isolation Voltage (input/output to case)
Continuous
Transient (≤ 1 s)
Output Current
Operating Case Temperature
Storage Case Temperature
Lead Temperature (20 s)
Voltage at ENA IN, ENA OUT
Voltage at STDBY
ELECTRICAL CHARACTERISTICS
Input Voltage
Continuous
Transient (1 s, Rs* = 0 Ω)
Transient (≤ 100 ms, Rs* = 0 Ω)
Transient (≤ 1 s, Rs* = 0 Ω)
Zero Load Input Current
See Note 1
-70
-70
100
210
V
V
-500
-1000
-0.5
0.0
500
1000
25
125
135
300
50
5.0
V
V
A
°C
°C
°C
V
V
-40
-50
-50
-50
70
80
100
210
9.5
V
V
V
V
mA
4.0
mA
-55
-65
HB Grade Products, See Note 7
See INPUT OVER VOLTAGE SHUTDOWN Application Section
Standby Mode Input Current
Output Voltage (continuous)
Output Current (continuous)
Output Power (continuous)
DC Resistance Rdc
Tcase = 25°C
Tcase = 125°C
Synchronous Rectifier Drop (Vsr)
Power Dissipation (20A output current)
Tcase = 25°C
Tcase = 125°C
Maximum Output Capacitance
Soft-Start Circuitry
Output current During Soft-Start
Soft-Start Duration Period
Soft-Start Recycle Period
Anti-Parallel Diode
Forward Current
Continuous
Transient (≤ 8 ms)
Forward Voltage (@ 1 A)
Total Differential-Mode Capacitance
Total Common-Mode Capacitance
Bulk Capacitor
Damping Resistor
Noise Attenuation
INPUT VOLTAGE SPIKE SUPPRESSION
Output Voltage Deviation due to a Spike
Input Voltage Spike (Centered on Vin)
±250 V, 100 µs, Emax = 15 mJ
±200 V, 10 µs, Rs* ≤ 0.5 Ω
±400 V, 5 µs, Rs* ≤ 0.5 Ω
±600 V, 10 µs, Rs* ≤ 0.5 Ω
Subgroup3
See
See
See
See
Note
Note
Note
Note
6
6
6
6
1, 2, 3
4
V
A
W
1, 2, 3
1, 2, 3
1, 2, 3
45
60
mΩ
mΩ
mV
1
3
18
24
1
W
W
mF
110
A
ms
ms
Vout = Vin - (Iin x Rdc) - Vsr
20
320
40
Vin = 16V
1.6
600
2
50
1.00
0.6
78
0.27
65
0.2
A
A
V
µF
µF
µF
Ω
1
3
See Note 4
1, 2, 3
1, 2, 3
1, 2, 3
Measured across input and output pins
Measured between any pin to case
See Figure 1
See Note 2
-10
-10
-10
-10
16
16
16
16
ΔV
ΔV
ΔV
ΔV
MIL-STD-1275B/D
MIL-STD-461C (CS06); DEF-STAN 61-5
MIL-STD-461C (CS06)
RTCA/DO-160E
* Rs = Source Impedance
Product # MQME-28E-T6
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0006011 Rev. B
01/23/15
Page 3
MQME-28E-T6
Current: 20A
Technical Specification
MQME-28E-T6 ELECTRICAL CHARACTERISTICS
Parameter
Min.
Typ.
Max. Units Notes & Conditions
Specifications subject to change without notice
Group A
Vin=28V DC ±5%, Pout=320W, unless otherwise specified
INPUT VOLTAGE SURGE SUPPRESSION
Output Voltage Deviation due to a Surge
Input Surge Voltage and Duration
60 V, 550 ms, Rs* = 0 Ω
80 V, 100 ms, Rs* = 0 Ω
100 V, 80 ms, Rs* = 0 Ω
110 V, 5 ms, Rs* = 0 Ω
202 V, 350 ms, Rs* = 0 Ω
ISOLATION CHARACTERISTICS
Input Voltage (any pin to case)
Continuous
Transient (≤ 100 µs)
Isolation Resistance (any pin to case)
FEATURE CHARACTERISTICS
Enable Input
Off-State Voltage
Off-State Voltage Pulldown Current
On-State Voltage
On-State Pine Leakage Current
Pull-Up Voltage
Enable Output
Off-State Resistance
Off-State Voltage
On-State Voltage
On-State Leakage Current
Standby Input
Normal-State Voltage
Standby-State Voltage
Pull-Up Voltage
Pull-Up Resistance
Under Voltage Lockout
Turn-On Input Voltage Threshold
Turn-Off Output Voltage Threshold
Output Power Limit (continuous)
RELIABILITY CHARACTERISTICS
Calculated MTBF (MIL-STD-217F2)
GB @ Tcase = 70ºC
AIF @ Tcase = 70ºC
WEIGHT CHARACTERISTICS
Device Weight
60
70
70
70
0
78
78
78
78
-500
-800
100
500
800
-0.5
80
2.0
0.8
3.2
4
50
20
4.5
17
-100
2
35
20
0
4
15.5
3.0
450
Output not clamped, within continuous operation
MIL-HDBK-704A; RTCA/DO-160E
MIL-STD-1275B/D; DEF-STAN 61-5
DEF-STAN 61-5
MIL-STD-1275B/D; DEF-STAN 61-5 (Part 6)/6, see Note 5
V
V
MΩ
V
µA
V
µA
V
1
1
1
Current drain required to ensure logic low
1
Imax drawn from pin allowed, module on
See Figure A
Ω
mV
V
µA
3.5
5
V
V
V
kΩ
16.0
4.0
V
V
W
5
50
15.0
2.0
V
V
V
V
V
14.8
0.69
106 Hrs.
106 Hrs.
79
g
Subgroup3
1
1
1
1
1
1
Electrical Characteristics Notes
1. While the filter will survive these input voltage limits, the filter’s output voltage will be outside the limits for an MQFL converter input voltage range.
2. Verified by qualification testing and analysis.
3. Only the ES and HB grade products are tested at three temperatures. The C grade products are tested at one temperature. Please refer to the
Construction and Environmental Stress Screening Options table for details.
4. Soft start is engaged only when the output voltage starts from zero or dips below the Turn-Off Output Voltage Threshold (4V max).
5. Module will shut down per Figure E.
6. Shutdown and Restart if the input voltage goes below the UVLO value or above 84V.
7. The specified operating case temperature for ES grade products is -45°C to 100°C. The specified operating case temperature for C grade products is
0°C to 70°C.
* Rs = Source Impedance
Product # MQME-28E-T6
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0006011 Rev. B
01/23/15
Page 4
MQME-28E-T6
Current: 20A
Technical Specification
20
10
Output Impedance Magnitude (ohms)
0
Attenuation (dB)
-20
-40
-60
-80
-100
-120
-140
-160
Common Mode
Differential Mode
0.1
0.01
0.001
-180
0.01
1
0.1
1
10
100
1000
10000
0.01
100000
Frequency (kHz)
0.1
1
10
100
1000
Frequency (kHz)
Figure 1: Typical Common Mode and Differential Mode Attenuation
provided by the filter as a function of frequency. Both input lines are
connected to chassis ground through 50Ω resistors. The filter case is
also connected to chassis ground.
Figure 2: Typical Output Impedance (magnitude) of the filter looking
back into its output pins with the input pins connected to a source
with zero source impedance.
Figure 3: MIL-STD-461E Method CE101 Low Frequency Conducted
Emissions. Limit line (in red) is the ‘Submarine Applications DC Curve’.
See MIL-STD-461 Compliance Matrix Table for test setup.
Figure 4: MIL-STD-461E Method CE102 High Frequency Conducted
Emissions. Limit line (in red) is the ‘Basic Curve’. See MIL-STD-461
Compliance Matrix Table for test setup.
Figure 5: MIL-STD-461E Method RE101 Low Frequency Radiated
Emissions. Limit line (in red) is the ‘Standard Curve’ from MIL-STD461C Method RE01, which is more strict than all RE101 limits. See
MIL-STD-461 Compliance Matrix Table for test setup.
Figure 6: MIL-STD-461E Method RE102 High Frequency Radiated
Emissions. Limit line (in red) is the ‘Submarine External to Pressure
Hull Curve’. See MIL-STD-461 Compliance Matrix Table for test setup.
Product # MQME-28E-T6
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0006011 Rev. B
01/23/15
Page 5
MQME-28E-T6
Current: 20A
Technical Specification
BASIC OPERATION AND FEATURES
The MQME-28E-T6 is a multi-stage differential-mode and commonmode passive EMI filter designed to interface a power source with
one or more SynQor DC/DC converters (or other loads that create
EMI). Each stage of this filter is well damped to avoid resonances
and oscillations, and only X7R multi-layer ceramic capacitors are
used. Figure 1 shows the typical differential and common-mode
attenuation provided by this filter when the source impedance is
50W to chassis ground on each input line.
The MQME-28E-T6 EMI filter includes a large bulk capacitor
(also X7R) with a series damping resistor to correct for the
unstabilizing effect of a converter’s negative input resistance. A
white paper discussing this negative input resistance and the need
for corrective damping can be found on the SynQor website (see
Input System Instability application note). Figure 2 shows the
magnitude of the filter’s output impedance when the filter input is
connected to a stiff voltage source.
When used with SynQor’s DC/DC converters, the MQME-28E-T6
EMI filter is designed to pass all the relevant MIL-STD-461C/D/
E/F requirements to their most stringent limits. The MIL-STD-461
Compliance Matrix Table lists these requirements and describes
the setup used to pass them. Figures 3 - 6 show results from
selected conductive and radiated emissions tests.
TRANSIENT SUPPRESSION: The input voltage surge and spike
compliance matrix displays the worst case requirements listed in
various 28V Military (Vehicle and Aircraft) and Civil Aircraft
standards. The MQME-28E-T6 EMI filter is designed to handle all
of the short duration voltage spike requirements of these standards
(with certain assumptions regarding DEF-STAN 61-5). Some of
the long duration voltage surge requirements remain within the
50V maximum transient rating of a SynQor MQFL-28 DC/DC
converter. The others require the transient suppression circuitry
of the MQME-28E-T6 EMI filter to protect the converter from an
over-voltage condition. If MQFL-28E or MQFL-28VE converters
are used, voltage surges as high as 80V can be tolerated without
the need for this transient suppression circuitry.
The MQME-28E-T6 EMI filter is also designed to pass the
waveform types and applications specified in RTCA/DO-160E
Section 22 (Lightning Induced Transient Susceptibility) to Level 4.
The Section 22 Compliance Matrix Table lists these waveforms
and applications and describes the setup used to pass them.
REVERSE POLARITY PROTECTION: The MQME-28E-T6
EMI filter has a series-connected MOSFET that is controlled to
function as a diode, but with a very small forward voltage drop
(≤ 4 mW x Iout). This “Synchronous Rectifier” blocks reverse
current flow if the filter’s input voltage is mistakenly connected
with the wrong polarity. The anti-parallel diode, working with the
synchronous rectifier, ensures that the filter’s output voltage goes
only slightly negative during this time, and therefore satisfying
the minimum input voltage specifications of SynQor’s MQFL
converters.
Product # MQME-28E-T6
Phone 1-888-567-9596
The synchronous rectifier also performs a useful function during
negative polarity spikes and surges, and during brief power
interrupts. Since it stops current from flowing negatively through the
EMI filter back toward the source, the synchronous rectifier allows
the total bulk capacitor (located both within and external to the
filter) to better hold up the output voltage during these transients.
ENABLE: The MQME-28E-T6 filter has enable pass-through
circuitry that bridges an enable signal across the filter’s commonmode impedance. The ENABLE INPUT pin (pin 4) is referenced
with respect to the filter’s INPUT RETURN (pins 5 and 6). The
ENABLE OUTPUT pin (pin 9) is referenced with respect to the
filter’s OUTPUT RETURN (pin 7). The INPUT RETURN and
OUTPUT RETURN may have a different voltage due to commonmode noise and transients.
NOTE: During the time that the MQME-28E-T6 filter is in its SoftStart mode the ENABLE OUTPUT will be held at a logic low. This is
done so that all of the filter’s loads can be disabled by this signal
during the Soft-Start period. Once the Soft-Start is completed,
ENABLE OUTPUT will follow ENABLE INPUT.
Figure A shows the equivalent circuit looking into ENABLE INPUT.
The ENABLE INPUT pin must be pulled low to turn an MQFL
converter off. It may be left open-circuit to turn the converter on.
5.6V
PIN 4
(ENABLE INPUT)
1N4148
82K
TO ENABLE
CIRCUITRY
250K
2N3904
33nF
125K
PINS 5 AND 6
(INPUT RETURN)
Figure A: Equivalent circuit looking into the ENABLE INPUT pin
with respect to the INPUT RETURN pin.
Figure B shows the equivalent circuit looking into ENABLE
OUTPUT. The n-channel MOSFET in this circuit turns on when
power is applied to the filter and ENABLE INPUT is low.
Otherwise, the MOSFET is off. ENABLE OUTPUT is capable of
driving the ENABLE INPUTs of up to 15 MQFL converters.
If the enable pass-through circuit is not being used, the
ENABLE INPUT pin may be left open or connected to the
INPUT RETURN pins. The ENABLE OUTPUT pin may be left open
or connected to the OUTPUT RETURN pins.
SOFT-START: The MQME-28E-T6 filter incorporates Soft-Start
circuitry to limit the amount of current drawn from the power
source by the charging of large bulk capacitors at the filter’s
output.
www.synqor.com
Doc.# 005-0006011 Rev. B
01/23/15
Page 6
MQME-28E-T6
Current: 20A
Technical Specification
STANDBY: The MQME-28E-T6 filter has standby circuitry that
minimizes the power drawn from the filter’s input power source
when the standby feature is activated.
PIN 9
(ENABLE OUTPUT)
0.01
µF
PIN 7
(OUTPUT RETURN)
Figure B: Equivalent circuit looking into the ENABLE OUTPUT pin
with respect to the OUTPUT RETURN pin.
Once the input voltage exceeds the turn-on threshold value,
the Soft-Start circuitry controls the filter’s output current to be
approximately 1.6A. This mode of operation continues until the
filter’s output voltage reaches the input voltage, at which time the
filter is able to deliver its rated output current. If after the SoftStart duration period the filter’s output has not risen to the input
voltage, then the filter will disconnect the output from the input,
wait for a time equal to the Soft-Start recycle period, and initiate
a new Soft-Start.
Since, during Soft-Start, the filter will deliver only 1.6A to its
output, it is important to limit the load current so that the total bulk
capacitance can be fully charged before the Soft-Start duration
period is over. To facilitate this, the filter’s ENABLE OUTPUT pin
is held low during the Soft-Start mode. This signal can therefore
be used to disable the filter’s loads during this time. Once the SoftStart mode is completed, ENABLE OUTPUT will follow ENABLE
INPUT.
40
800
35
700
30
600
25
500
20
400
15
300
10
200
Current
Power
5
Figure D shows the equivalent circuit looking into the STANDBY
pin (pin 8).
This pin is referenced with respect to the filter’s OUTPUT RETURN
pin (pin 7). It should be pulled low to have the filter operate in
its normal mode. If the pin is instead left open-circuit and pulled
high by its internal circuitry, the standby feature will be activated.
Application Note: A typical application would place the
MQME filter close to the input of the DC/DC converter, with the
cases of the filter and the converter connected together through
a ground plane. Both cases are electrically conductive, so
connection to the cases can be made with the fasteners used to
secure the device.
Do not connect the outputs of multiple MQME-28E-T6 filters in
parallel. Connecting filters in this manner may result in slightly
unequal currents to flow in the positive and return paths of each
filter. These unequal currents may cause the internal commonmode chokes to saturate and thus cause degraded common-mode
rejection performance.
5V
Power Output (W)
Output Current (A)
OUTPUT POWER LIMIT: The MQME-28E-T6 filter has an
output power limit feature to protect against a short circuit at its
output pins. This limit is disabled whenever the output voltage is
rising so that it will not be encountered when charging output
capacitance. When the output power exceeds ~450W and its
output voltage is decreasing however, this feature will turn the
filter off and reinstitute a soft-start cycle in 500ms. Figure C shows
the output power limit threshold as a function of output voltage.
It does this in two ways. First, the output of the filter is disconnected
from the input so that there will be no power drawn by downstream
converters or other loads. Second, the active circuitry within the
filter is placed into a reduced power consumption mode. The
net result is a current draw of only about 2mA from a 28V input
power source.
50k
PIN 8
(Standby)
To Standby Circuitry
0.01 µF
PIN 7
(Output Return)
100
0
0
0
10
20
30
40
50
60
70
Output Voltage (V)
Figure D: Equivalent circuit looking into the STANDBY pin with
respect to the OUTPUT RETURN pin.
Figure C: Output Power Limit.
Product # MQME-28E-T6
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0006011 Rev. B
01/23/15
Page 7
MQME-28E-T6
Current: 20A
Technical Specification
160
140
Input Voltage (V)
120
100
80
60
40
20
0
1
10
Time (ms)
100
1000
Figure E: Input over voltage shutdown envelope.
INPUT OVER VOLTAGE SHUTDOWN: To protect itself from
damage due to sustained excessive power dissipation, the filter will
shut down if the input voltage versus time exceeds the envelope in
Figure E.
During this shutdown, power flow to the load is interrupted and
the filter’s ENABLE OUTPUT pin is pulled LOW. When the input
voltage returns to normal limits (and a Soft-Start Recycle Period has
elapsed), the filter automatically begins a Soft-Start cycle.
All of the surges listed in the VOLTAGE SURGE AND SPIKE
COMPLIANCE MATRIX on page 11 fall below the Figure E envelope.
Only the DEF STAN 61-5 (Part 6)/6 DIT08.B surge exceeds this
envelope. During a DIT08.B surge the filter will shutdown and
then automatically restart once the surge passes. This meets the
requirements of DEF STAN 61-5 (Part 6)/6 at Performance Criterion
C while the DIT08.B test requires only Performance Criterion D.
Product # MQME-28E-T6
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0006011 Rev. B
01/23/15
Page 8
MQME-28E-T6
Current: 20A
Technical Specification
SEE
NOTE 7
1
2
3
4
5
6
+VIN
+VOUT
+VOUT
+VIN
+VIN
ENA IN
MQME-28E-T6-X-HB
EMI FILTER
28Vin 20A
320W
IN RTN
IN RTN
+VOUT
ENA OUT
MADE IN USA
S/N 0000000 D/C 3205-301 CAGE 1WX10
STDBY
OUT RTN
12
11
10
9
8
7
0.250 [6.35]
1.50 [38.10]
0.200 [5.08]
TYP. NON-CUM.
1.260
[32.00]
0.040 [1.02]
PIN
2.50 [63.50]
2.76 [70.10]
3.00 [76.20]
0.050 [1.27]
0.128 [3.25]
0.220 [5.59]
2.96 [75.2]
0.228 [5.79]
0.390 [9.91]
Case X
SEE
NOTE 7
1
2
3
4
5
6
+VIN
+VOUT
+VIN
+VOUT
+VIN
MQME-28E-T6-U-HB
ENA IN
EMI FILTER
28Vin 20A
IN RTN
IN RTN
+VOUT
ENA OUT
320W
MADE IN USA
S/N 0000000 D/C 3205-301 CAGE 1WX10
STDBY
OUT RTN
12
11
10
9
8
7
0.250 [6.35]
0.200 [5.08]
TYP. NON-CUM.
1.50 [38.10]
1.260
[32.00]
2.50 [63.50]
2.76 [70.10]
3.00 [76.20]
0.040 [1.02]
PIN
0.128 [3.25]
0.42
[10.7]
0.050 [1.27]
0.220 [5.59]
2.80 [71.1]
Case U
0.390 [9.91]
NOTES
PIN DESIGNATIONS
1)
Pins 0.040’’ (1.02mm) diameter
2)
Pins Material: Copper Alloy
Finish: Gold over Nickel plating, followed by Sn/Pb solder dip
3)
All dimensions in inches (mm) Tolerances: x.xx +/-0.02 in. (x.x +/-0.5mm)
x.xxx +/-0.010 in. (x.xx +/-0.25mm)
4)
Weight: 2.8 oz (78.5 g) typical
5)
Workmanship: Meets or exceeds IPC-A-610C Class III
6)
Print Labeling on Top Surface per Product Label Format Drawing
7)
Pin 1 identification hole, not intended for mounting (case X and U)
Product # MQME-28E-T6
Phone 1-888-567-9596
www.synqor.com
Pin # Function
1
2
3
4
5
6
Positive input
Positive input
Positive input
Enable input
Input return
Input return
Doc.# 005-0006011 Rev. B
Pin # Function
7
8
9
10
11
12
Output Return
Standby
Enable output
Positive output
Positive output
Positive output
01/23/15
Page 9
MQME-28E-T6
Current: 20A
Technical Specification
0.300 [7.62]
0.140 [3.56]
1.15 [29.21]
0.250 [6.35]
TYP
1
2
3
4
5
6
+VIN
+VOUT
+VIN
+VOUT
MQME-28E-T6-Y-HB
+VIN
EMI FILTER
28Vin 20A
ENA IN
IN RTN
IN RTN
+VOUT
ENA OUT
320W
MADE IN USA
S/N 0000000 D/C 3205-301 CAGE 1WX10
STDBY
OUT RTN
1.750 [44.45]
12
2.00
11
[50.80]
10
1.50
9 [38.10]
8
1.750
7
[44.45]
0.250 [6.35]
0.200 [5.08]
TYP. NON-CUM.
0.040 [1.02]
PIN
0.050 [1.27]
0.220 [5.59]
0.375 [9.52]
2.50 [63.50]
2.96 [75.2]
0.228 [5.79]
0.390 [9.91]
Case Y
Case Z
(variant of Y)
0.250 [6.35]
Case W
(variant of Y)
0.250 [6.35]
0.200 [5.08]
TYP. NON-CUM.
0.200 [5.08]
TYP. NON-CUM.
0.040 [1.02]
PIN
0.040 [1.02]
PIN
0.22 [5.6]
0.050 [1.27]
0.42 [10.7]
0.36 [9.14]
0.050 [1.27]
0.22 [5.6]
2.80 [71.1]
0.525 [13.33]
0.390
[9.91]
0.525 [13.33]
0.390
[9.91]
2.80 [71.1]
NOTES
PIN DESIGNATIONS
1)
Pins 0.040’’ (1.02mm) diameter
2)
Pins Material: Copper Alloy
Finish: Gold over Nickel plating, followed by Sn/Pb solder dip
3)
All dimensions in inches (mm) Tolerances: x.xx +/-0.02 in. (x.x +/-0.5mm)
x.xxx +/-0.010 in. (x.xx +/-0.25mm)
4)
Weight: 2.8 oz (78.5 g) typical
5)
Workmanship: Meets or exceeds IPC-A-610C Class III
6)
Print Labeling on Top Surface per Product Label Format Drawing
7)
Pin 1 identification hole, not intended for mounting (case X and U)
Product # MQME-28E-T6
Phone 1-888-567-9596
www.synqor.com
Pin # Function
1
2
3
4
5
6
Positive input
Positive input
Positive input
Enable input
Input return
Input return
Doc.# 005-0006011 Rev. B
Pin # Function
7
8
9
10
11
12
Output Return
Standby
Enable output
Positive output
Positive output
Positive output
01/23/15
Page 10
MQME-28E-T6
Current: 20A
Technical Specification
VOLTAGE SURGE AND SPIKE COMPLIANCE MATRIX
These tables show the Voltage Surge and Spike requirements/limits that have been met* by a stand-alone setup comprised of:
-
MQME-28-P (or –T) Filter
MQFL-28-05S DC/DC Converter
120W Resistive Load
Metal Chassis Plane
Vehicle 28Vin
Worst Case Over-Voltage Surge
Part
(Voltage/Duration)
(Gen. + Bat.)
MIL-STD-1275D
40V / 50ms
(Bat. only)
100V / 50ms
(Gen. only)
100V / 50ms
+70V to -40V / 5ms§
+70V to -40V / 5ms§
(Bat. Only)
(Bat. Only, Non-Regen. Ld. Sw.)
80V / 80ms§
(Bat. Only, Regen. Ld. Sw.)
40V / 50ms
80V / 80m§
(Gen. only)
DET03.A
DET04.A
DIT04.A
Aircraft 28Vin
MIL-HDBK-704-8
Part
±200V / 200ns / 50W
+70V to -40V / 1ms§
+110V / 300ms§
+90V to -60V / 10µs§
Worst Case Over-Voltage Surge
(Voltage/Duration)
Short Duration Spikes
(Voltage/Duration/Impedance)
80V / 50ms
(704A)
60V / 550ms
N/A
50V / 50ms
47V / 100ms
(Cat A)
±600V / 10µs / 50W
38V / 1s
60V / 100ms
(Cat B)
±200V / 10µs / 50W
40V / 1s
80V / 100ms
(Cat C)
Met by any Hi-Rel Filter
+280V to -220V max§
+130V to -70V / 10µs§
+174V / 350ms
40V / 50ms§
(704B, C, D, E, F)
RTCA/DO-160E
+130V to -100V max§
+90V to -60V / 10µs§
100V / 50ms
+110V to -50V / 5ms§
DIT08.B, DIT07.B
DEF STAN 61-5 (PART 6)/6†
±250V / 15mJ / 0.5W
40V / 50ms
(Gen. + Bat.)
DEF STAN 61-5 (PART 6)/5†
Short Duration Spikes
(Voltage/Duration/Impedance)
N/A
48V / 1s
Met by an MQME-28-T Filter having the Transient Suppression
and Reverse Polarity Protection Features
Met by MQME-28E-T6 Filter Only:
Performance Criteria C
* Surge/spike requirements/limits are deemed to have been met as long as transient deviations in the converter’s output voltage
remain within ±10% of its initial value.
§ These are defined as the maximum disturbances that equipment can inflict upon the power system, not as disturbances imposed
upon utilization equipment. To ensure compatablitily, however, these are within the designed stress envelope of the indicated filters
& converters.
† For the DEF STAN 61-5 specification:
1) Negative surges require reverse voltage protection circuitry to protect the converter (but not the filter) from a negative input.
This circuitry is included in the MQME-28-T but not the MQME-28-P and MQHE-28-P filters.
2) The negative surges may cause the converter to shut down unless additional holdup capacitance is included.
3) Maximum spike voltages are assumed to last <1µs
Product # MQME-28E-T6
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0006011 Rev. B
01/23/15
Page 11
MQME-28E-T6
Current: 20A
Technical Specification
RTCA/DO-160E SECTION 22 COMPLIANCE MATRIX
(LIGHTNING INDUCED TRANSIENT SUSCEPTIBILITY)
The following table shows the RTCA/DO-160 Section 22 requirements that have been met* by a stand-alone setup comprised of:
- MQME-28-P (or –T) Filter
- MQFL-28-05S DC/DC Converter
- Resistive Load
- Metal Chassis Plane
- Unshielded Power Cable Bundle
Pin Injection
Single- and
Multiple-Stroke
Cable Induction
Single- and
Multiple-Stroke
Ground Injection
Multiple-Burst
Cable Induction
Waveform
Maximum Level Passed
3
4
4
4†
5a
4†
2
4**
3
4
4
4
5a
4
3
4
Met by any MQME/MQHE Filter
Test Conditions
Signal applied to +Vin pin. Input Return pin connected to system ground
Signal applied to unshielded power
cable bundle
Signal applied between metal ground
plane and system ground
Signal applied to unshielded power
cable bundle
Met by an MQME Filter having the Transient Suppression
and Reverse Polarity Protection Features
* Requirement is deemed to have been met as long as transient deviations in the converter’s output voltage remain within ±10% of
its initial value.
† For these waveforms at Level 3 and above, an external transient suppressor of sufficient energy rating must placed across the filter’s
input pins to keep the differential transient input voltage below +200V/-50V. Negative polarity waveforms may cause power flow
to the converter to be interrupted long enough to cause a graceful shutdown and restart of the converter. Also, the reverse voltage
protection feature of the -T filter is required to protect the converter (but not the filter) from negative polarity waveform.
** For this waveform at a Level 4 and above, external transient suppressors of sufficient energy rating must be added between the
filter’s input power pins and its case to keep the common-mode transient input voltage below +800V.
Product # MQME-28E-T6
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0006011 Rev. B
01/23/15
Page 12
MQME-28E-T6
Current: 20A
Technical Specification
MIL-STD-461 COMPLIANCE MATRIX
This table shows the MIL-STD-461 requirements/limits that have been met* by a stand-alone setup comprised of:
-
MQME-28-P (or –T) Filter
MQFL-28-05S DC/DC Converter
120W Resistive Load
Metal Chassis Plane
-461C
-461D/E/F
Most Stringent Limit
Listed
Requirement
CE01
CE03
CE07
Class A5 (Submarine)
Class A5 (Submarine)
Class A1 (Aircraft)
CS01
CS02
Class A5 (Submarine)
Class A5 (Submarine)
CS06
Class A1/A5 (Aircraft/Sub)
CS10
CS11
Class A5 (Submarine)
Class A5 (Submarine)
Radiated
Emissions
RE01
RE02†
Radiated
Susceptibility
RS01
RS02
RS03
Conducted
Emissions
Conducted
Susceptibility
Requirement
Most Stringent
Limit Listed
CE101
CE102
Submarine
Basic Curve
CS101
CS114
CS115
CS116
Curve #2
Curve #5
Basic Waveform
IMAX = 10A
Class A5 (Submarine)
Class A5 (Submarine)
RE101
RE102†
Navy
Submarine
Class A5 (Submarine)
Class A1/A5 (Aircraft/Sub)
Class A4 (Surface Ship)
RS101
RS103
Army
Aircraft External
Met by any MQME/MQHE Filter
Met by an MQME Filter having the Transient Suppression
and Reverse Polarity Protection Features
* Susceptibility requirements/limits are deemed to have been met as long as transient deviations in the converter’s output voltage
remain within ±10% of its initial value.
† Met with metal screen shield covering the filter, converter, and resistive load.
Product # MQME-28E-T6
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0006011 Rev. B
01/23/15
Page 13
MQME-28E-T6
Current: 20A
Technical Specification
CONSTRUCTION AND ENVIRONMENTAL STRESS SCREENING OPTIONS
Screening
Consistent with
MIL-STD-883F
(
Element Evaluation
C-Grade
specified from
0 ºC to +70 ºC
) (
ES-Grade
specified from
-45 ºC to +100 ºC
) (
HB-Grade
specified from
-55 ºC to +125 ºC
)
No
Yes
Yes
*
Yes
Yes
Yes
Temperature Cycle
Method 1010
No
Condition B
(-55 ºC to +125 ºC)
Condition C
(-65 ºC to +150 ºC)
Constant Acceleration
Method 2001
(Y1 Direction)
No
500g
Condition A
(5000g)
Burn-in
Method 1015
24 Hrs @ +125 ºC
96 Hrs @ +125 ºC
160 Hrs @ +125 ºC
+25 ºC
-45, +25, +100 ºC
-55, +25, +125 ºC
Full QorSeal
Full QorSeal
Full QorSeal
Internal Visual
Final Electrical Test
Method 5005 (Group A)
Mechanical Seal,
Thermal, and
Coating Process
External Visual
2009
Construction Process
*
Yes
Yes
QorSeal
QorSeal
QorSeal
* Per IPC-A-610 Class 3
MilQor converters and filters are offered in three variations of environmental stress screening options. All MilQor converters use SynQor’s proprietary
QorSeal™ Hi-Rel assembly process that includes a Parylene-C coating of the circuit, a high performance thermal compound filler, and a nickel barrier
gold plated aluminum case. Each successively higher grade has more stringent mechanical and electrical testing, as well as a longer burn-in cycle. The
ES- and HB-Grades are also constructed of components that have been procured through an element evaluation process that pre-qualifies each new batch
of devices.
Product # MQME-28E-T6
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0006011 Rev. B
01/23/15
Page 14
MQME-28E-T6
Current: 20A
Technical Specification
MilQor Filter FAMILY MATRIX
The tables below show the array of MilQor filters available. When ordering SynQor converters, please ensure that you use
the complete part number according to the table in the last page. Contact the factory for other requirements.
Features Available
Product Family Continuous
Designator
Input Voltage
Power
(Amperage)
Rating
MQME-28
40V
MQME-28E
70V
MQHE-28
MQHE-28E
MQHE-270
40V
70V
400V
MQME-270
400V
320W (2A)
MQME-270L
400V
200W (3A)
Product # MQME-28E-T6
Version
(see table
below)
320W (20A)
P
T
T6
160W (10A)
P
160W (1A)
P
Phone 1-888-567-9596
(In Addition to Passive Filter Components)
Enable PassThrough
Circuitry
Transient
Suppression
Circuitry
Soft-Start
Circuitry
Reverse
Polarity
Protection
Circuitry
•
•
•
•
•
•
•
•
P
•
R
P
•
R
www.synqor.com
Doc.# 005-0006011 Rev. B
01/23/15
Page 15
MQME-28E-T6
Current: 20A
Technical Specification
PART NUMBERING SYSTEM
The part numbering system for SynQor’s MilQor DC-DC converters follows the format shown in the table below.
Model Name
Input Voltage Range
Version
28
28E
P
T
T6
270
270L
P
R
MQME
MQHE
Package Outline/Pin
Configuration
Screening
Grade
U
X
Y
W
Z
C
ES
HB
Not all combinations make valid part numbers, please contact SynQor for availability. See the Product Summary web page for more options.
Example:
MQME-28E-T6-Y-ES
APPLICATION NOTES
A variety of application notes and technical white papers can be downloaded in pdf format from the SynQor website.
PATENTS
SynQor holds the following U.S. patents, one or more of which apply to this product: Additional patent applications may be
pending or filed in the future.
5,999,417
6,222,742
6,545,890
6,577,109
6,594,159
6,731,520
6,894,468
6,896,526
6,927,987
7,050,309
7,072,190
7,085,146
7,119,524
7,269,034
7,272,021
7,272,023
7,558,083
7,564,702
7,765,687
7,787,261
8,023,290
8,149,597
8,493,751
8,644,027
Contact SynQor for further information:
Phone:
Toll Free:
Fax:
E-mail:
Web:
Address:
Product # MQME-28E-T6
978-849-0600
888-567-9596
978-849-0602
[email protected]
www.synqor.com
155 Swanson Road
Boxborough, MA 01719
USA
Phone 1-888-567-9596
Warranty
SynQor offers a two (2) year limited warranty. Complete warranty
information is listed on our website or is available upon request from
SynQor.
Information furnished by SynQor is believed to be accurate and reliable.
However, no responsibility is assumed by SynQor for its use, nor for any
infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any
patent or patent rights of SynQor.
www.synqor.com
Doc.# 005-0006011 Rev. B
01/23/15
Page 16