MQME-28-P Passive Filter

MQME-28-P
Passive Filter
-40V to +40V
20A
35mΩ @ 125°C
>80dB @ 500kHz
Continuous Input
Output Current
Max. DC Resistance
Differential Attenuation
The MilQor® series of high-reliability EMI filters brings
SynQor’s field proven technology and manufacturing
expertise to the Military/Aerospace industry. SynQor’s
innovative QorSeal
TM
packaging approach ensures
survivability in the most hostile environments. Compatible
with the industry standard format, these filters have high
differential-mode and common-mode attenuation, low
-HB
P-Y
DC resistance, and a stabilizing bulk capacitor resistor.
8E-2
M
TER 20W
3
I FIL
EM n 20A
i
28V
MQ
They follow conservative component derating guidelines
and they are designed and manufactured to comply with
a wide range of military standards.
Design Process
MQME series filters are:
• DesignedforreliabilityperNAVSO-P3641-Aguidelines
• Designedwithcomponentsderatedper:
—MIL-HDBK-1547A
—NAVSOP-3641A
Qualification Process
MQME series filters are qualified to:
• MIL-STD-810F
—consistentwithRTCA/DO-160E/F/G
• SynQor’sFirstArticleQualification
—consistentwithMIL-STD-883F
• SynQor’sLong-TermStorageSurvivabilityQualification
• SynQor’son-goinglifetest
In-Line Manufacturing Process
• AS9100andISO9001:2008certifiedfacility
• Fullcomponenttraceability
• Temperaturecycling
• Constantacceleration
• 24,96,160hourburn-in
• Threeleveltemperaturescreening
Product # MQME-28-P
Phone 1-888-567-9596
DesigneD & ManufactureD in the usa
featuring Qorseal™ hi-rel asseMbly
Features
•20ampsoutputcurrent
•VerylowDCresistance
•>80dBdifferential-modeattenuationat500kHz
•>60dBcommon-modeattenuationat500kHz
•Stabilizingbulkcapacitoranddampingresistorincluded
•AllcapacitorsareX7Rmulti-layerceramic
•DesignedtomeetallMIL-STD461EMIandmostRTCA/
DO-160E/F/GSection22lightningrequirements
Specification Compliance
MQME series filters (with MQFL converters) are designed to meet:
• MIL-HDBK-704-8(AthroughF)
• RTCA/DO-160E/F/GSection16
• MIL-STD-1275B
• DEF-STAN61-5(part6)/5
• MIL-STD-461(C,D,E,F)
• RTCA/DO-160E/F/GSection22
www.synqor.com
Doc.# 005-2ME028P Rev. F
08/28/13
Page 1
MQME-28-P
Current: 20A
Technical Specification
BLOCK DIAGRAM
POSITIVE
OUTPUT
POSITIVE
INPUT
RDAMPING
PINS 1, 2, 3
PINS 4, 5, 6
PINS 10, 11, 12
PINS 7, 8, 9
CBULK
INPUT
RETURN
OUTPUT
RETURN
TYPICAL CONNECTION DIAGRAM
+VIN
+VIN
+VOUT
MQFL DC-DC
CONVERTER
MQME EMI
FILTER
-VIN
+VOUT
IN RTN
-VOUT
+VIN
LOAD
OUT RTN
+VOUT
MQFL DC-DC
CONVERTER
IN RTN
LOAD
OUT RTN
TO OTHER
LOADS
Product # MQME-28-P
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-2ME028P Rev. F
08/28/13
Page 2
MQME-28-P
Current: 20A
Technical Specification
MQME-28-P ELECTRICAL CHARACTERISTICS
Parameter
Min. Typ. Max. Units Notes & Conditions
Vin=28V DC ±5%, Iout= 20A unless otherwise specified
ABSOLUTE MAXIMUM RATINGS
Input Voltage
Continuous
Transient (≤ 1 s)
Isolation Voltage (Input/Output to case)
Continuous
Transient (≤ 1 s)
Output Current
Operating Case Temperature
Storage Case Temperature
Lead Temperature (20 s)
ELECTRICAL CHARACTERISTICS
Input Voltage
Continuous
Transient (≤1 s, RS* = 0 Ω)
Transient (≤100 ms, RS* = 0 Ω)
Output Voltage (continuous)
Output Current (continuous)
DC Resistance RDC
TCASE = 25°C
TCASE = 125°C
Power Dissipation (20A output current)
TCASE = 25°C
TCASE = 125°C
Total Differential-Mode Capacitance
Total Common-Mode Capacitance
Bulk Capacitor
Damping Resistor
Noise Attenuation
INPUT VOLTAGE SPIKE SUPPRESSION
Output Voltage Deviation due to a Spike
Input Voltage Spike (Centered on Vin)
±250V, 100µs, Emax = 15mJ
±600V, 10µs, Rs* = 50Ω
ISOLATION CHARACTERISTICS
Isolation Voltage (any pin to case)
Continuous
Transient (≤ 100 µs)
Isolation Resistance (any pin to case)
Group A
Subgroup3
See Note 1
-100
-200
100
200
V
V
-500
-1000
500
1000
20
125
135
300
V
V
A
°C
°C
°C
-55
-65
HB Grade Products, See Note 4
See Note 1
-40
40
-50
50
-100
100
Vout = Vin - (Iin x Rdc)
20
V
V
V
V
A
1, 2, 3
25
35
mΩ
mΩ
1
3
10
14
W
W
µF
µF
µF
Ω
71
0.28
58
0.2
1, 2, 3
1, 2, 3
1, 2, 3
Measured across input or output pins
Measured between any pin to case
See Figure 1
See Note 2
-5
-5
5
10
ΔV
ΔV
-500
-800
100
500
800
V
V
MΩ
MIL-STD-1275B/D
RTCA/DO-160E
1
1
* Rs = Source Impedance
Product # MQME-28-P
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-2ME028P Rev. F
08/28/13
Page 3
MQME-28-P
Current: 20A
Technical Specification
MQME-28-P ELECTRICAL CHARACTERISTICS (Continued)
Parameter
Min. Typ. Max. Units Notes & Conditions
Group A
Vin=28V DC ±5%, Iout= 20A unless otherwise specified
RELIABILITY CHARACTERISTICS
Calculated MTBF (MIL-STD-217F2)
GB @ Tcase = 70ºC
AIF @ Tcase = 70ºC
WEIGHT CHARACTERISTICS
Device Weight
21.7
1.26
106 Hrs.
106 Hrs.
79
g
Subgroup3
Electrical Characteristics Notes
1. While the filter will survive these input voltage limits, the filter’s output voltage will be outside the limits for an MQFL converter input voltage range.
2. Verified by qualification testing and analysis.
3. Only the ES and HB grade products are tested at three temperatures. The C grade products are tested at one temperature. Please refer to the
Construction and Environmental Stress Screening Options table for details.
4. The specified operating case temperature for ES grade products is -45ºC to 100ºC. The specified operating case temperature for C grade products
is 0ºC to 70ºC.
* Rs = Source Impedance
Product # MQME-28-P
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-2ME028P Rev. F
08/28/13
Page 4
MQME-28-P
Current: 20A
Technical Specification
20
10
Output Impedance Magnitude (ohms)
0
Attenuation (dB)
-20
-40
-60
-80
-100
-120
-140
-160
Common Mode
Differential Mode
0.1
0.01
0.001
-180
0.01
1
0.1
1
10
100
1000
10000
0.01
100000
Frequency (kHz)
0.1
1
10
100
1000
Frequency (kHz)
Figure 1: Typical Common Mode and Differential Mode Attenuation
provided by the filter as a function of frequency. Both input lines are
connected to chassis ground through 50Ω resistors. The filter case is
also connected to chassis ground.
Figure 2: Typical Output Impedance (magnitude) of the filter looking
back into its output pins with the input pins connected to a source
with zero source impedance.
Figure 3: MIL-STD-461E Method CE101 Low Frequency Conducted
Emissions. Limit line (in red) is the ‘Submarine Applications DC Curve’.
Figure 4: MIL-STD-461E Method CE102 High Frequency Conducted
Emissions. Limit line (in red) is the ‘Basic Curve’.
Figure 5: MIL-STD-461E Method RE101 Low Frequency Radiated
Emissions. Limit line (in red) is the ‘Standard Curve’ from MIL-STD461C Method RE01, which is more strict than all RE101 limits.
Figure 6: MIL-STD-461E Method RE102 High Frequency Radiated
Emissions. Limit line (in red) is the 5Submarine External to Pressure
Hull Curve.
Product # MQME-28-P
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-2ME028P Rev. F
08/28/13
Page 5
MQME-28-P
Current: 20A
Technical Specification
BASIC OPERATION AND FEATURES
The MQME is a multi-stage differential-mode and commonmode passive EMI filter designed to interface a power source
with one or more SynQor DC/DC converters (or other loads that
create EMI). Each stage of this filter is well damped to avoid
resonances and oscillations, and only X7R multi-layer ceramic
capacitors are used. Figure 1 shows the typical differential and
common-mode attenuation provided by this filter when the
source impedance is 50Ω to chassis ground on each input line.
The MQME EMI filter includes a large bulk capacitor (also X7R)
with a series damping resistor to correct for the unstabilizing
effect of a converter’s negative input resistance. A white paper
discussing this negative input resistance and the need for
corrective damping can be found on the SynQor website (see
Input System Instability application note). Figure 2 shows the
magnitude of the filter’s output impedance when the filter input
is connected to a stiff voltage source.
The input voltage surge and spike compliance matrix displays
the worst case requirements listed in various 28V Military
(Vehicle and Aircraft) and Civil Aircraft standards. The MQME
EMI filter is designed to handle all of the short duration voltage
spike requirements of these standards (with certain assumptions
regarding DEF-STAN 61-5). Some of the long duration voltage
surge requirements remain within the 50V maximum transient
rating of a SynQor MQFL-28 DC/DC converter. The others
require the transient suppression circuitry of an MQME-28-T EMI
filter to protect the converter from an overvoltage condition. If
MQFL-28E or MQFL-28VE converters are used, voltage surges as
high as 80V can be tolerated without the need for this transient
suppression circuitry.
Product # MQME-28-P
Phone 1-888-567-9596
When used with SynQor’s DC/DC converters, the MQME EMI
filter is designed to pass all of the relevant MIL-STD-461C/D/E
requirements to their most stringent limits. The MIL-STD-461
Compliance Matrix Table lists these requirements and describes
the setup used to pass them. Figures 3 - 6 show results from
selected conductive and radiated emissions tests.
The filter is also designed to pass the waveform types and
applications specified in RTCA/DO-160E Section 22 (Lightning
Induced Transient Susceptibility) to Level 4 (some waveforms/
applications require the MQME-28-T filter and/or external
transient suppression circuitry). The Section 22 Compliance
Matrix Table lists these waveforms and applications and
describes the setup used to pass them.
A typical application would place the MilQor filter close to the
input of the DC/DC converter, with the cases of the filter and
the converter connected together through a ground plane. Both
cases are electrically conductive, so connection to the cases can
be made with the fasteners used to secure the device.
Do not connect the outputs of multiple MQME filters in parallel.
Connecting filters in this manner may result in slightly unequal
currents to flow in the positive and return paths of each filter.
These unequal currents may cause the internal common-mode
chokes to saturate and thus cause degraded common-mode
rejection performance.
www.synqor.com
Doc.# 005-2ME028P Rev. F
08/28/13
Page 6
MQME-28-P
Current: 20A
Technical Specification
MIL-STD-461 COMPLIANCE MATRIX
This table shows the MIL-STD-461 requirements/limits that have been met* by a stand-alone setup comprised of:
-
MQME-28-P Filter
MQFL-28-05S DC/DC Converter
Resistive Load
Metal Chassis Plane
-461C
-461D/E
Most Stringent Limit
Listed
Requirement
CE01
CE03
CE07
Class A5 (Submarine)
Class A5 (Submarine)
Class A1 (Aircraft)
CS01
CS02
Class A5 (Submarine)
Class A5 (Submarine)
CS06
Class A1/A5 (Aircraft/Sub)
CS10
CS11
Class A5 (Submarine)
Class A5 (Submarine)
Radiated
Emissions
RE01
RE02†
Radiated
Susceptibility
RS01
RS02
RS03
Conducted
Emissions
Conducted
Susceptibility
Requirement
Most Stringent
Limit Listed
CE101
CE102
Submarine
Basic Curve
CS101
CS114
CS115
CS116
Curve #2
Curve #5
Basic Waveform
IMAX = 10A
Class A5 (Submarine)
Class A5 (Submarine)
RE101
RE102†
Navy
Submarine
Class A5 (Submarine)
Class A1/A5 (Aircraft/Sub)
Class A4 (Surface Ship)
RS101
RS103
Army
Aircraft External
Met by any MQME/MQHE Filter
Met by an MQME Filter having the Transient Suppression
and Reverse Polarity Protection Features
* Susceptibility requirements/limits are deemed to have been met as long as transient deviations in the converter’s output voltage
remain within ±10% of its initial value.
† Met with metal screen shield covering the filter, converter, and resistive load.
Product # MQME-28-P
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-2ME028P Rev. F
08/28/13
Page 7
MQME-28-P
Current: 20A
Technical Specification
RTCA/DO-160E SECTION 22 COMPLIANCE MATRIX
(LIGHTNING INDUCED TRANSIENT SUSCEPTIBILITY)
The following table shows the RTCA/DO-160 Section 22 requirements that have been met* by a stand-alone setup comprised of:
- MQME-28-P (or –T) Filter
- MQFL-28-05S DC/DC Converter
- Resistive Load
- Metal Chassis Plane
- Unshielded Power Cable Bundle
Pin Injection
Single- and
Multiple-Stroke
Cable Induction
Single- and
Multiple-Stroke
Ground Injection
Multiple-Burst
Cable Induction
Waveform
Maximum Level Passed
3
4
4
4†
5a
4†
2
4**
3
4
4
4
5a
4
3
4
Met by any MQME/MQHE Filter
Test Conditions
Signal applied to +Vin pin. Input Return pin connected to system ground
Signal applied to unshielded power
cable bundle
Signal applied between metal ground
plane and system ground
Signal applied to unshielded power
cable bundle
Met by an MQME Filter having the Transient Suppression
and Reverse Polarity Protection Features
* Requirement is deemed to have been met as long as transient deviations in the converter’s output voltage remain within ±10% of its
initial value.
† For these waveforms at Level 3 and above, an external transient suppressor of sufficient energy rating must placed across the filter’s
input pins to keep the differential transient input voltage below +200V/-50V. Negative polarity waveforms may cause power flow to the
converter to be interrupted long enough to cause a graceful shutdown and restart of the converter. Also, the reverse voltage protection
feature of the -T filter is required to protect the converter (but not the filter) from negative polarity waveform.
** For this waveform at a Level 4 and above, external transient suppressors of sufficient energy rating must be added between the
filter’s input power pins and its case to keep the common-mode transient input voltage below +800V.
Product # MQME-28-P
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-2ME028P Rev. F
08/28/13
Page 8
MQME-28-P
Current: 20A
Technical Specification
VOLTAGE SURGE AND SPIKE COMPLIANCE MATRIX
These tables show the Voltage Surge and Spike requirements/limits that have been met* by a stand-alone setup comprised of:
-
MQME-28-P (or –T) Filter
MQFL-28-05S DC/DC Converter
120W Resistive Load
Metal Chassis Plane
Vehicle 28Vin
Worst Case Over-Voltage Surge
Part
(Voltage/Duration)
(Gen. + Bat.)
MIL-STD-1275D
40V / 50ms
(Bat. only)
100V / 50ms
(Gen. only)
100V / 50ms
+70V to -40V / 5ms §
(Bat. Only)
(Bat. Only, Non-Regen. Ld. Sw.)
(Gen. only)
DIT08.B, DIT07.B
80V / 80ms §
MIL-HDBK-704-8
40V / 50ms
80V / 80ms §
100V / 50ms
+110V to -50V / 5ms §
+280V to -220V max §
+130V to -70V / 10µs §
+174V / 350ms
±200V / 200ns / 50Ω
DET03.A
40V / 50ms §
DET04.A
+70V to -40V / 1ms §
DIT04.A
+110V / 300ms §
Aircraft 28Vin
Part
(Voltage/Duration)
Short Duration Spikes
(Voltage/Duration/Impedance)
80V / 50ms
(704A)
60V / 550ms
N/A
50V / 50ms
47V / 100ms
(Cat A)
±600V / 10µs / 50Ω
38V / 1s
60V / 100ms
(Cat B)
±200V / 10µs / 50Ω
40V / 1s
80V / 100ms
(Cat C)
Met by any Hi-Rel Filter
+90V to -60V / 10µs §
Worst Case Over-Voltage Surge
(704B, C, D, E, F)
RTCA/DO-160E
+130V to -100V max §
+90V to -60V / 10µs §
+70V to -40V / 5ms §
(Bat. Only, Regen. Ld. Sw.)
DEF STAN 61-5 (PART 6)/6†
±250V / 15mJ / 0.5Ω
40V / 50ms
(Gen. + Bat.)
DEF STAN 61-5 (PART 6)/5†
Short Duration Spikes
(Voltage/Duration/Impedance)
N/A
48V / 1s
Met by an MQME-28-T Filter having the Transient Suppression
and Reverse Polarity Protection Features
Met by MQME-28E-T6 Filter Only:
Performance Criteria C
* Surge/spike requirements/limits are deemed to have been met as long as transient deviations in the converter’s output voltage
remain within ±10% of its initial value.
§ These are defined as the maximum disturbances that equipment can inflict upon the power system, not as disturbances imposed
upon utilization equipment. To ensure compatablitily, however, these are within the designed stress envelope of the indicated filters &
converters.
† For the DEF STAN 61-5 specification:
1) Negative surges require reverse voltage protection circuitry to protect the converter (but not the filter) from a negative input.
This circuitry is included in the MQME-28-T but not the MQME-28-P and MQHE-28-P filters.
2) The negative surges may cause the converter to shut down unless additional holdup capacitance is included.
3) Maximum spike voltages are assumed to last <1µs
Product # MQME-28-P
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-2ME028P Rev. F
08/28/13
Page 9
MQME-28-P
Current: 20A
Technical Specification
CONSTRUCTION AND ENVIRONMENTAL STRESS SCREENING OPTIONS
Screening
Consistent with
MIL-STD-883F
(
Element Evaluation
C-Grade
specified from
0 ºC to +70 ºC
) (
ES-Grade
specified from
-45 ºC to +100 ºC
) (
HB-Grade
specified from
-55 ºC to +125 ºC
)
No
Yes
Yes
*
Yes
Yes
Yes
Temperature Cycle
Method 1010
No
Condition B
(-55 ºC to +125 ºC)
Condition C
(-65 ºC to +150 ºC)
Constant Acceleration
Method 2001
(Y1 Direction)
No
500g
Condition A
(5000g)
Burn-in
Method 1015
24 Hrs @ +125 ºC
96 Hrs @ +125 ºC
160 Hrs @ +125 ºC
+25 ºC
-45, +25, +100 ºC
-55, +25, +125 ºC
Full QorSeal
Full QorSeal
Full QorSeal
Internal Visual
Final Electrical Test
Method 5005 (Group A)
Mechanical Seal,
Thermal, and
Coating Process
External Visual
2009
Construction Process
*
Yes
Yes
QorSeal
QorSeal
QorSeal
* Per IPC-A-610 Class 3
MilQor converters and filters are offered in three variations of environmental stress screening options. All MilQor converters use SynQor’s proprietary
QorSeal™ Hi-Rel assembly process that includes a Parylene-C coating of the circuit, a high performance thermal compound filler, and a nickel barrier
gold plated aluminum case. Each successively higher grade has more stringent mechanical and electrical testing, as well as a longer burn-in cycle. The
ES- and HB-Grades are also constructed of components that have been procured through an element evaluation process that pre-qualifies each new batch
of devices.
Product # MQME-28-P
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-2ME028P Rev. F
08/28/13
Page 10
MQME-28-P
Current: 20A
Technical Specification
SEE
NOTE 7
1
2
3
4
5
6
+VIN
+VOUT
+VIN
+VOUT
+VIN
+VOUT
OUT RTN
IN RTN
MADE IN USA
IN RTN
IN RTN
S/N 0000000 D/C 3205-301 CAGE 1WX10
OUT RTN
OUT RTN
12
11
10
9
8
7
0.250 [6.35]
1.50 [38.10]
1.260
[32.00]
0.200 [5.08]
TYP. NON-CUM.
0.040 [1.02]
PIN
2.50 [63.50]
2.76 [70.10]
3.00 [76.20]
0.050 [1.27]
0.128 [3.25]
0.220 [5.59]
2.96 [75.2]
0.228 [5.79]
0.390 [9.91]
Case X
SEE
NOTE 7
1
2
3
4
5
6
+VIN
+VOUT
+VIN
+VOUT
+VIN
+VOUT
OUT RTN
IN RTN
IN RTN
IN RTN
MADE IN USA
S/N 0000000 D/C 3205-301 CAGE 1WX10
OUT RTN
OUT RTN
12
11
10
9
8
7
2.50 [63.50]
2.76 [70.10]
3.00 [76.20]
0.250 [6.35]
0.200 [5.08]
TYP. NON-CUM.
1.50 [38.10]
1.260
[32.00]
0.040 [1.02]
PIN
0.128 [3.25]
0.42
[10.7]
0.050 [1.27]
0.220 [5.59]
2.80 [71.1]
0.390 [9.91]
Case U
NOTES
PIN DESIGNATIONS
1)
Pins 0.040’’ (1.02mm) diameter
2)
Pins Material: Copper Alloy
Finish: Gold over Nickel plating, followed by Sn/Pb solder dip
3)
All dimensions in inches (mm) Tolerances: x.xx +/-0.02 in. (x.x +/-0.5mm)
x.xxx +/-0.010 in. (x.xx +/-0.25mm)
4)
Weight: 2.8 oz (78.5 g) typical
5)
Workmanship: Meets or exceeds IPC-A-610C Class III
6)
Print Labeling on Top Surface per Product Label Format Drawing
7)
Pin 1 identification hole, not intended for mounting (case X and U)
Product # MQME-28-P
Phone 1-888-567-9596
www.synqor.com
Pin # Function
1
2
3
4
5
6
Positive input
Positive input
Positive input
Input return
Input return
Input return
Doc.# 005-2ME028P Rev. F
Pin # Function
7
8
9
10
11
12
Output return
Output return
Output return
Positive output
Positive output
Positive output
08/28/13
Page 11
MQME-28-P
Current: 20A
Technical Specification
0.300 [7.62]
0.140 [3.56]
1.15 [29.21]
0.250 [6.35]
TYP
1
2
3
4
5
6
+VIN
+VOUT
+VIN
+VOUT
+VIN
+VOUT
OUT RTN
IN RTN
IN RTN
IN RTN
MADE IN USA
S/N 0000000 D/C 3205-301 CAGE 1WX10
OUT RTN
OUT RTN
1.750 [44.45]
12
2.00
11
[50.80]
10
1.50
9 [38.10]
8
1.750
7
[44.45]
0.250 [6.35]
0.200 [5.08]
TYP. NON-CUM.
0.040 [1.02]
PIN
0.050 [1.27]
0.220 [5.59]
0.375 [9.52]
2.50 [63.50]
2.96 [75.2]
0.228 [5.79]
0.390 [9.91]
Case Y
Case Z
(variant of Y)
0.250 [6.35]
Case W
(variant of Y)
0.250 [6.35]
0.200 [5.08]
TYP. NON-CUM.
0.200 [5.08]
TYP. NON-CUM.
0.040 [1.02]
PIN
0.040 [1.02]
PIN
0.22 [5.6]
0.050 [1.27]
0.42 [10.7]
0.36 [9.14]
0.050 [1.27]
0.22 [5.6]
2.80 [71.1]
0.525 [13.33]
0.390
[9.91]
0.525 [13.33]
0.390
[9.91]
2.80 [71.1]
NOTES
PIN DESIGNATIONS
1)
Pins 0.040’’ (1.02mm) diameter
2)
Pins Material: Copper Alloy
Finish: Gold over Nickel plating, followed by Sn/Pb solder dip
3)
All dimensions in inches (mm) Tolerances: x.xx +/-0.02 in. (x.x +/-0.5mm)
x.xxx +/-0.010 in. (x.xx +/-0.25mm)
4)
Weight: 2.8 oz (78.5 g) typical
5)
Workmanship: Meets or exceeds IPC-A-610C Class III
6)
Print Labeling on Top Surface per Product Label Format Drawing
7)
Pin 1 identification hole, not intended for mounting (case X and U)
Product # MQME-28-P
Phone 1-888-567-9596
www.synqor.com
Pin # Function
1
2
3
4
5
6
Positive input
Positive input
Positive input
Input return
Input return
Input return
Doc.# 005-2ME028P Rev. F
Pin # Function
7
8
9
10
11
12
Output return
Output return
Output return
Positive output
Positive output
Positive output
08/28/13
Page 12
MQME-28-P
Current: 20A
Technical Specification
MilQor Filter FAMILY MATRIX
The tables below show the array of MilQor filters available. When ordering SynQor converters, please ensure that you use
the complete part number according to the table in the last page. Contact the factory for other requirements.
Features Available
Product Family Continuous
Designator
Input Voltage
Power
(Amperage)
Rating
MQME-28
40V
MQME-28E
70V
MQHE-28
MQHE-28E
MQHE-270
40V
70V
400V
MQME-270
400V
320W (2A)
MQME-270L
400V
200W (3A)
Product # MQME-28-P
Version
(see table
below)
320W (20A)
P
T
T6
160W (10A)
P
160W (1A)
P
Phone 1-888-567-9596
(In Addition to Passive Filter Components)
Enable PassThrough
Circuitry
Transient
Suppression
Circuitry
Soft-Start
Circuitry
Reverse
Polarity
Protection
Circuitry
•
•
•
•
•
•
•
•
P
•
R
P
•
R
www.synqor.com
Doc.# 005-2ME028P Rev. F
08/28/13
Page 13
MQME-28-P
Current: 20A
Technical Specification
PART NUMBERING SYSTEM
The part numbering system for SynQor’s MilQor DC-DC converters follows the format shown in the table below.
Model Name
Input Voltage Range
Version
28
28E
P
T
T6
270
270L
P
R
MQME
MQHE
Package Outline/Pin
Configuration
Screening
Grade
U
X
Y
W
Z
C
ES
HB
Not all combinations make valid part numbers, please contact SynQor for availability. See the Product Summary web page for more options.
Example:
MQME-28-P-Y-ES
APPLICATION NOTES
A variety of application notes and technical white papers can be downloaded in pdf format from the SynQor website.
PATENTS
SynQor holds the following U.S. patents, one or more of which apply to this product: Additional patent applications may be
pending or filed in the future.
5,999,417
6,222,742
6,545,890
6,577,109
6,594,159
6,731,520
6,894,468
6,896,526
6,927,987
7,050,309
7,072,190
7,085,146
7,119,524
7,269,034
7,272,021
7,272,023
7,558,083
7,564,702
7,765,687
7,787,261
8,023,290
8,149,597
Contact SynQor for further information:
Phone:
Toll Free:
Fax:
E-mail:
Web:
Address:
Product # MQME-28-P
978-849-0600
888-567-9596
978-849-0602
[email protected]
www.synqor.com
155 Swanson Road
Boxborough, MA 01719
USA
Phone 1-888-567-9596
Warranty
SynQor offers a two (2) year limited warranty. Complete warranty
information is listed on our website or is available upon request from
SynQor.
Information furnished by SynQor is believed to be accurate and reliable.
However, no responsibility is assumed by SynQor for its use, nor for any
infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any
patent or patent rights of SynQor.
www.synqor.com
Doc.# 005-2ME028P Rev. F
08/28/13
Page 14