EClamp2455K ESD/EMI Protection for SIM Card PRELIMINARY PROTECTION PRODUCTS - EMIClampTM Description Features The EClampTM2455K is combination EMI filter and line termination device with integrated TVS diodes for use on SIM Card interfaces on cellular phones and other portable electronics. This state-of-the-art device utilizes solid-state silicon-avalanche technology for superior clamping performance and DC electrical characteristics. Bidirectional EMI/RFI filter with integrated TVS for ESD protection ESD protection to IEC 61000-4-2 (ESD) Level 4, The device consists of three circuits that include series impedance matching resistors for proper termination of the SIM card interface. Termination resistor value of 100 Ohms is included on the RST and Data lines and 47 Ohms on the CLK line. TVS diodes are also included on each line for ESD protection in excess of ±15kV (air discharge) and ±8kV (contact discharge) per IEC 610004-2, level 4. An additional TVS diode connection is included for protection of the voltage (Vcc) bus. ±15kV (air), ±8kV (contact) TVS working voltage: 5V Termination Resistors: 100 Ohms & 47 Ohms Capacitance: 20pF (Typical at VR = 0V) Protection and filtering for four lines Solid-state technology Mechanical Characteristics The EClamp2455K is in a 8-pin, RoHS/WEEE compliant, SLP1713P8 package. It measures 1.7 x 1.3 x 0.50mm. The leads are spaced at a pitch of 0.4mm and are finished with lead-free NiPdAu. The small package makes it ideal for use in portable electronics such as cell phones and digital still cameras. SLP1713P8 8-pin package RoHS/WEEE Compliant Nominal Dimensions: 1.7 x 1.3 x 0.50 mm Lead Pitch: 0.4mm Lead finish: NiPdAu Marking: Marking Code Packaging: Tape and Reel per EIA 481 Applications SIM Card Cell Phone PDAs and Smartphones Package Configuration Pin Configuration 1.70 1 2 RST Out 1 8 CLK Out CLK In Gnd 0.40 BSC Data In Data Out NC 1.30 RST In 4 5 Vcc 0.50 Pin Identification and Configuration (Top Side View) Revision 03/27/2007 8 Pin SLP package (Bottom Side View) Nominal Dimensions in mm 1 www.semtech.com EClamp2455K PRELIMINARY PROTECTION PRODUCTS Pin Identification and Configuration Pin Symbol Identification 1, 8 RST Reset input/output with termination resistor 2, 7 C LK Clock input/output with termination resistor 3, 6 Data Data input/output with termination resistor 4 NC No Connect 5 Vcc Power Supply ESD Protection Center tab GND Ground connection 8 7 6 5 3 4 Gnd 1 2 Pin Configuration (Top View) Schematics & Component Values Vcc 100 Ω RST IN RST OUT 47 Ω CLK IN CLK OUT 100 Ω Data OUT Data IN GND © 2007 Semtech Corp. 2 www.semtech.com EClamp2455K PRELIMINARY PROTECTION PRODUCTS Maximum Ratings R ating Symbol Value Units VESD +/- 18 +/- 12 kV Junction Temp erature TJ 125 o Op erating Temp erature Top -40 to +85 o Storage Temp erature TSTG -55 to +150 o ESD p er IEC 61000-4-2 (Air) ESD p er IEC 61000-4-2 (Contact) C C C Electrical Characteristics (T=25oC) P ar am et er S y m b ol Con d i t i on s Mi n i mu m Ty p i c a l M ax i m u m Units 5 V 10 V 0.5 μA T VS Reverse Stand-Off Voltage VRWM T VS Reverse Breakdown Voltage V BR It = 1mA IR VRWM = 5.0V Reset Series Resistors RRST Each Line 85 100 115 Ohms Clk Series Resistors R CLK Each Line 40 47 55 Ohms Data Series Resistors RDATA Each Line 85 100 115 Ohms Cin Inp ut to Gnd, Each Line VR = 0V, f = 1MHz 16 20 24 pF T VS Reverse Leakage Current Total Cap acitance © 2007 Semtech Corp. 3 6 8 www.semtech.com EClamp2455K PRELIMINARY PROTECTION PRODUCTS Typical Characteristics Typical Insertion Loss S21 (Pin 2 to 7) CH1 S21 LOG Typical Insertion Loss S21 (Pin 1 to 8 and Pin 3 to 6) 6 dB / REF 0 dB CH1 S21 LOG 6 dB / REF 0 dB 1: -6.4316 dB 307.466 MHz 1: -8.9909 dB 294.402 MHz 2: -14.641 dB 900 MHz 0 dB 3: -23.808dB 1.8 GHz -6 dB 1 -12 dB -18 dB 1 -12 dB 4: -30.765 dB 2.5 GHz -18 dB 5: -30.455 dB 2.7 GHz -24 dB 3: -28.966dB 1.8 GHz -6 dB 4: -28.845 dB 2.5 GHz 2 2: -19.003 dB 900 MHz 0 dB 5: -30.974 dB 2.7 GHz 2 -24 dB 3 5 -30 dB 5 -30 dB 4 3 4 -36 dB -36 dB -42 dB -42 dB -48 dB 1 MHz 10 MHz 100 MHz -48 dB 1 3 GHz GHz STOP 3000. 000000 MHz START. 030 MHz 1 MHz 10 MHz 1 3 GHz GHz STOP 3000. 000000 MHz START. 030 MHz ESD Clamping (+8kV Contact) 100 MHz ESD Clamping (-8kV Contact) Note: Data is taken with a 10x attenuator Note: Data is taken with a 10x attenuator Analog Crosstalk (Each Line) Normalized Capacitance vs. Reverse Voltage CH1 S21 1.1 LOG 20 dB /REF 0 dB 1 0.9 CJ(VR) / CJ(VR=0) 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 f = 1 MHz 0 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 Reverse Voltage - VR (V) © 2007 Semtech Corp. START. 030 MHz 4 STOP 3000. 000000 MHz www.semtech.com EClamp2455K PRELIMINARY PROTECTION PRODUCTS Device Connection Figure 1 - Pin Identification and Configuration (Top Side View) The EClamp2455K designed with ease of layout in mind. The package has flow through design which allows the designer to route the signals straight in and out between the SIM port connector and the SIM controller. The device is in a 8-pin SLP package. Electrical connection is made to the 8 pins located at the bottom of the device. A center tab serves as the ground connection. Pin connections are noted in Figure 1. All path lengths should be kept as short as possible to minimize the effects of parasitic inductance in the board traces. RST Out 1 8 CLK Out CLK In Gnd Data In Data Out NC RST In 4 5 Vcc SIM Controller SIM Card Connector RST OUT 1 RST In 8 CLK OUT CLK IN Gnd DATA OUT 4 DATA IN Vcc 5 Reset Clock Data I/O 5V/3.3V/1.8V EClamp2455K EClamp2455P Figure 2 - SIM Protection © 2007 Semtech Corp. 5 www.semtech.com EClamp2455K PRELIMINARY PROTECTION PRODUCTS Applications Information - Spice Model EClamp2455K Spice Model & Parameters Vcc 100 Ω RST IN RST OUT 47 Ω CLK IN CLK OUT 100 Ω Data OUT Data IN GND EClamp2455K Spice Model Note: All TVS shown in the circuit use D1 Parameters Table 1 - EClamp2455K Spice Parameters © 2007 Semtech Corp. Parameter Unit D1 (T VS) IS Amp 2E-15 BV Volt 7.5 VJ Volt 0.775 RS Ohm 1.05 IB V A mp 1E-3 CJO Farad 9E-12 TT sec 2.541E-9 M -- 0.246 N -- 1.1 EG eV 1.11 6 www.semtech.com EClamp2455K PRELIMINARY PROTECTION PRODUCTS Outline Drawing - SLP1713P8 A D B DIM PIN 1 INDICATOR (LASER MARK) A A1 A2 b D D1 E E1 e L N aaa bbb E A SEATING PLANE aaa C A2 C A1 DIMENSIONS INCHES MILLIMETERS MIN NOM MAX MIN NOM MAX .018 .020 .022 .000 .001 .002 (.005) .006 .008 .010 .065 .067 .070 .047 .051 .055 .049 .051 .054 .008 .012 .016 .016 BSC .008 .010 .012 8 .003 .004 0.45 0.50 0.55 0.00 0.02 0.05 (0.13) 0.15 0.20 0.25 1.65 1.70 1.775 1.20 1.30 1.40 1.25 1.30 1.375 0.20 0.30 0.40 0.40 BSC 0.20 0.25 0.30 8 0.08 0.10 D1 1 2 LxN E/2 E1 N bxN e/2 bbb C A B e D/2 NOTES: 1. CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES). 2. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMINALS. Land Pattern - SLP1713P8 P X Z G DIM C G H K P X Y Z H (C) Y DIMENSIONS INCHES MILLIMETERS (.050) (1.27) .027 0.69 .012 0.30 .055 1.40 .016 0.40 .008 0.20 .023 0.58 .073 1.85 K NOTES: 1. CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES). 2. THIS LAND PATTERN IS FOR REFERENCE PURPOSES ONLY. CONSULT YOUR MANUFACTURING GROUP TO ENSURE YOUR COMPANY'S MANUFACTURING GUIDELINES ARE MET. 3. THERMAL VIAS IN THE LAND PATTERN OF THE EXPOSED PAD SHALL BE CONNECTED TO A SYSTEM GROUND PLANE. FAILURE TO DO SO MAY COMPROMISE THE THERMAL AND/OR FUNCTIONAL PERFORMANCE OF THE DEVICE. © 2007 Semtech Corp. 7 www.semtech.com EClamp2455K PRELIMINARY PROTECTION PRODUCTS Marking Ordering Information 2455K PIN 1 INDICATOR XXXX Part Number Qty per Reel R eel Size EClamp 2455K.TCT 3000 7 Inch This is a lead-free RoHS/WEEE Compliant Device EMIClamp and EClamp are marks of Semtech Corporation XXXX = Date Code Tape and Reel Specification Pin 1 Location User Direction of feed Device Orientation in Tape A0 1.51 +/-0.05 mm B0 K0 1.91 +/-0.05 mm 0.66 +/-0.05 mm Tap e Width B, (Max) D D1 8 mm 4.2 mm (.165) 1.5 + 0.1 mm - 0.0 mm (0.59 +.005 - .000) 0.8 mm ±0.05 (.031) F K (MAX) P P0 P2 T(MAX) W 3.5±0.05 mm (.138±.002) 2.4 mm (.094) 4.0±0.1 mm (.157±.004) 4.0±0.1 mm (.157±.004) 2.0±0.05mm (.079±.002) 0.4 mm (.016) 8.0 mm + 0.3 mm - 0.1 mm (.312±.012) E 1.750±.10 mm (.069±.004) Contact Information for Semtech International AG Taiw an Branch Korea Branch Tel: 886-2-2748-3380 Fax: 886-2-2748-3390 Semtech Sw itz erland GmbH Japan Branch Tel: 81-3-6408-0950 Fax: 81-3-6408-0951 Tel: 82-2-527-4377 Fax: 82-2-527-4376 Semtech Limited (U.K.) Tel: 44-1794-527-600 Fax: 44-1794-527-601 Tel: 86-21-6391-0830 Fax: 86-21-6391-0831 Semtech France SARL Tel: 33-(0)169-28-22-00 Fax: 33-(0)169-28-12-98 Semtech International AG is a wholly-owned subsidiary of Semtech Corporation, which has its headquarters in the U.S.A. Semtech Germany GmbH Tel: 49-(0)8161-140-123 Fax: 49-(0)8161-140-124 © 2007 Semtech Corp. 8 Shanghai Office www.semtech.com