EClamp0504T

EClamp0504T
Low Profile EClamp®
4-Line ESD protection
PROTECTION PRODUCTS - EMIClamp®
Description
Features
The EClamp 0504T is designed to protect sensitive electronics from damage or latch-up due to ESD. This stateof-the-art device utilizes solid-state silicon-avalanche
technology for superior clamping performance and DC
electrical characteristics. It has been optimized for protection of digital lines in cellular phones and other
portable electronics.
‹ Transient protection for data lines to
®
‹
‹
‹
‹
‹
‹
The device replaces up to eight discrete components in
a small footprint. It consists of a TVS diode and a
series 1K Ohm resistor on each line. The TVS diode
presents a maximum loading capacitance of 15pF for
maximum signal integrity. The TVS diodes provide
effective suppression of ESD voltages in excess of
±15kV (air discharge) and ±8kV (contact discharge) per
IEC 61000-4-2, level 4.
IEC 61000-4-2 (ESD) ±17kV (air), ±12kV (contact)
IEC 61000-4-4 (EFT) 40A (tp = 5/50ns)
Cable Discharge Event (CDE)
Protects four data lines
TVS working voltage: 5V
Series Resistor: 1K Ohm
Capacitance: 15pF (Maximum at VR = 0V)
Low leakage current (<100nA)
Solid-state silicon-avalanche technology
Mechanical Characteristics
‹
‹
‹
‹
‹
‹
‹
The EClamp0504T is in an 8-pin SLP2116P8T package.
It measures 2.1 x 1.6 x 0.40mm. The leads are
spaced at a pitch of 0.5mm and are finished with leadfree NiPdAu. Each device will protect four lines operating at 5 volts. It gives the designer the flexibility to
protect single lines in applications where arrays are not
practical. The small package makes it ideal for use in
portable electronics such as cell phones, digital still
cameras, and PDAs.
SLP2116P8T package
Pb-Free, Halogen Free, RoHS/WEEE Compliant
Nominal Dimensions: 2.1 x 1.6 x 0.4 mm
Lead Finish: NiPdAu
Molding compound flammability rating: UL 94V-0
Marking : Marking code
Packaging : Tape and Reel
Applications
‹
‹
‹
‹
‹
‹
Schematic
Cellular Handsets & Accessories
Personal Digital Assistants (PDAs)
Notebooks & Handhelds
Portable Instrumentation
Peripherals
MP3 Players
Package Configuration
1K Ω
1, 2, 3, 4
2.10
5, 6, 7, 8
1 2
15pF
1.60
0.50 BSC
Tab
0.40
Pin Identification and Configuration
(4 each)
Revision 3/9/2011
8 Pin SLP package (Bottom Side View)
Nominal Dimensions in mm
1
www.semtech.com
EClamp0504T
PROTECTION PRODUCTS
Absolute Maximum Rating
R ating
Symbol
Value
Units
Peak Pulse Power (tp = 8/20μs)
Pp k
25
Watts
Maximum Peak Pulse Current (tp = 8/20μs)
Ip p
2
Amps
VESD
+/- 17
+/- 12
kV
TJ
-40 to +85
°C
TSTG
-55 to +150
°C
ESD p er IEC 61000-4-2 (Air) 1
ESD p er IEC 61000-4-2 (Contact)
1
Op erating Temp erature
Storage Temp erature
Notes:
1) ESD rating between pins 1, 2, 3, and 4 to ground. Pins 5, 6, 7, and 8 not rated for IEC level ESD discharges
Electrical Characteristics (T=25oC)
P ar am et er
S y m b ol
Con d i t i on s
Mi n i mu m
Ty p i c a l
M ax i m u m
Units
5
V
10
V
0.1
μA
T VS Reverse Stand-Off Voltage
VRWM
T VS Reverse Breakdown Voltage
V BR
It = 1mA
T VS Reverse Leakage Current
IR
VRWM = 5.0V
Total Series Resistance
R
Each Line
850
1000
1150
Ohms
Total Cap acitance
Cin
Inp ut to Gnd,
Each Line
VR = 0V, f = 1MHz
10
12
15
pF
6
8
Pin Identification and Configuration
Pin
Symbol
Identification
1
I/O In
Data Inp ut (Connector Side)
2
I/O In
Data Inp ut (Connector Side)
3
I/O In
Data Inp ut (Connector Side)
4
I/O In
Data Inp ut (Connector Side)
5
I/O Out
Data Outp ut (To Protected IC)
6
I/O Out
Data Outp ut (To Protected IC)
7
I/O Out
Data Outp ut (To Protected IC)
8
I/O Out
Data Outp ut (To Protected IC)
Tab
GN D
Ground
© 2011 Semtech Corp.
1
8
Pin Configuration (Top View)
2
www.semtech.com
EClamp0504T
PROTECTION PRODUCTS
Typical Characteristics
Non-Repetitive Peak Pulse Power vs. Pulse Time
Power Derating Curve
110
10
90
% of Rated Power or IPP
Peak Pulse Power - PPP (kW)
100
1
0.1
80
70
60
50
40
30
20
10
0
0.01
0.1
1
10
0
100
25
50
75
100
125
150
Ambient Temperature - TA (oC)
Pulse Duration - tp (us)
Forward Voltage vs. Forward Current
Normalized Junction Capacitance vs. Reverse Voltage
2.0
1.1
f = 1 MHz
1
0.9
Forward Voltage - VF (V)
CJ(VR) / CJ(VR=0)
0.8
0.7
0.6
0.5
0.4
0.3
0.2
1.5
1.0
0.5
Waveform
Parameters:
tr = 8μs
td = 20μs
0.1
0
0.0
0
1
2
3
Reverse Voltage - VR (V)
4
5
0
0.5
1
1.5
Forward Current - IF (A)
2
2.5
Insertion Loss S21
ESD Clamping (Measured between I/O in and Gnd)
(8kV Contact per IEC 61000-4-2)
CH1 S21
LOG
6 dB / REF 0 dB
1: -23.827 dB
285 MHz
0 dB
2: -31.805 dB
800.000 MHz
-6 dB
3: -32.767 dB
900.000 MHz
-12 dB
4: -29.769 dB
1.8 GHz
-18 dB
1
-24 dB
5
5: -21.999 dB
2.5 GHz
-30 dB
4
2
3
-36 dB
-42 dB
-48 dB
Note: Data is taken with a 10x attenuator
© 2011 Semtech Corp.
1
MHz
START . 030 MHz
3
10
MHz
100
MHz
3
1
GHz GHz
STOP 3000. 000000 MHz
www.semtech.com
EClamp0504T
PROTECTION PRODUCTS
Applications Information
Device Connection Options
Circuit Diagram
This device is designed to protect four data lines. The
device is unidirectional and may be used on lines
where the signal polarity is above ground.
1K Ω
In
Circuit Board Layout Recommendations for Suppression of ESD.
15pF
Good circuit board layout is critical for the suppression
of ESD induced transients. The following guidelines are
recommended:
z Place the TVS near the input terminals or connectors to restrict transient coupling.
z Minimize the path length between the TVS and the
protected line.
z Minimize all conductive loops including power and
ground loops.
z The ESD transient return path to ground should be
kept as short as possible.
z Never run critical signals near board edges.
z Use ground planes whenever possible.
© 2011 Semtech Corp.
Out
Tab
4
www.semtech.com
EClamp0504T
PROTECTION PRODUCTS
Applications Information - Spice Model
R1
1
2
1K Ω
D1
3
Spice Model
Table 1 - Spice Parameters
© 2011 Semtech Corp.
Parameter
Unit
D1 (T VS)
IS
Amp
2E-15
BV
Volt
7.56
VJ
Volt
0.776
RS
Ohm
0.912
IB V
Amp
1.0E-3
CJO
Farad
11.5E-12
TT
sec
2.541E-9
M
--
0.23
N
--
1.1
EG
eV
1.11
5
www.semtech.com
EClamp0504T
PROTECTION PRODUCTS
Outline Drawing - SLP2116P8T
A
B
D
DIM
E
PIN 1
INDICATOR
(LASER MARK)
A
SEATING
PLANE
aaa C
A2
A1
C
D1
A
A1
A2
b
D
D1
E
E1
e
L
N
aaa
bbb
DIMENSIONS
INCHES
MILLIMETERS
MIN NOM MAX MIN NOM MAX
.015 .016 .017 0.37 0.40 0.43
.000 .001 .002 0.00 .003 0.05
(.005)
(0.13)
.008 .010 .012 0.20 0.25 0.30
.079 .083 .087 2.00 2.10 2.20
.061 .067 .071 1.55 1.70 1.80
.059 .063 .067 1.50 1.60 1.70
.010 .016 .020 0.25 0.40 0.50
.020 BSC
0.50 BSC
.011 .013 .015 0.28 0.33 0.38
8
8
.003
0.08
.004
0.10
1 2
LxN
E/2
E1
N
bxN
e
bbb
C A B
D/2
NOTES:
1. CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES).
2. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMINALS.
Land Pattern - SLP2116P8T
P
X
DIMENSIONS
Z
H
G
(C)
Y
DIM
C
G
H
K
P
X
Y
Z
INCHES
(.060)
.035
.018
.071
.020
.012
.025
.085
MILLIMETERS
(1.52)
0.89
0.45
1.80
0.50
0.30
0.63
2.15
K
NOTES:
1. CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES).
2. THIS LAND PATTERN IS FOR REFERENCE PURPOSES ONLY.
CONSULT YOUR MANUFACTURING GROUP TO ENSURE YOUR
COMPANY'S MANUFACTURING GUIDELINES ARE MET.
3. THERMAL VIAS IN THE LAND PATTERN OF THE EXPOSED PAD
SHALL BE CONNECTED TO A SYSTEM GROUND PLANE.
FAILURE TO DO SO MAY COMPROMISE THE THERMAL AND/OR
FUNCTIONAL PERFORMANCE OF THE DEVICE.
© 2011 Semtech Corp.
6
www.semtech.com
EClamp0504T
PROTECTION PRODUCTS
Marking Code
Ordering Information
0504T
PIN 1
INDICATOR
Part Number
Working
Voltage
Qty per
Reel
Reel
Size
EClamp 0504T.TCT
5V
3,000
7 Inch
EMIClamp and EClamp are trademarks of Semtech Corporation
YYWW
YYWW = Date Code
Tape and Reel Specification
Pin 1 Location
User Direction of feed
Device Orientation in Tape
A0
1.96 +/-0.10 mm
B0
K0
2.31 +/-0.10 mm
0.66 +/-0.10 mm
Tape
Width
B, (Max)
D
D1
8 mm
4.2 mm
(.165)
1.5 + 0.1 mm
- 0.0 mm
(0.59 +.005
- .000)
0.4 mm
±0.25
(.031)
E
1.750±.10
mm
(.069±.004)
F
P
P0
P2
T
W
3.5±0.05
mm
(.138±.002)
4.0±0.10
mm
(.157±.004)
4.0±0.1
mm
(.157±.004)
2.0±0.05
mm
(.079±.002)
0.254±0.02
mm (.016)
8.0 mm
+ 0.3 mm
- 0.1 mm
(.312±.012)
Contact Information for Semtech International AG
Taiw an Branch
Tel: 886-2-2748-3380
Fax: 886-2-2748-3390
Semtech Sw itz erland GmbH
Japan Branch
Tel: 81-3-6408-0950
Fax: 81-3-6408-0951
Tel: 82-2-527-4377
Fax: 82-2-527-4376
Semtech Limited (U.K.)
Tel: 44-1794-527-600
Fax: 44-1794-527-601
Tel: 86-21-6391-0830
Fax: 86-21-6391-0831
Semtech France SARL
Tel: 33-(0)169-28-22-00
Fax: 33-(0)169-28-12-98
Semtech International AG is a wholly-owned subsidiary of
Semtech Corporation, which has its headquarters in the U.S.A.
Semtech Germany GmbH
Tel: 49-(0)8161-140-123
Fax: 49-(0)8161-140-124
© 2011 Semtech Corp.
7
Korea Branch
Shanghai Office
www.semtech.com