RACD12 - recom

Features
LED
DRIVER
●
●
●
●
●
●
●
●
●
12W Class II AC/DC LED Power Supply
ENEC, UL, RCM and CB Certified
Active Power Factor Corrected >0.95
Fused Input, Protected Output
3kVAC Input/Output Isolation
Output Socket Connector
cUL/UL-8750 Certified
Low Cost
Long 5 Year Warranty
LIGHTLINE
AC/DC-Converter
with 5 year Warranty
Description
12 Watt PFC
Single
Output
A compact 12W constant current switching power module suitable for driving up to ten high power LEDs (Vf = 3.6V).
The output current is fixed at 350mA, 500mA or 700mA. Active power factor correction is standard and the converters
are UL8750 certified for use with LED assemblies. The driver module features both screw terminal and socket output
connections. The socket connector avoids the possibility of miswiring and damaging the LED load if the LEDs are
pre-assembled into a wiring harness or lamp fitting.
Selection Guide
Part
Number
Nominal
Input Voltage
(VAC)
Input Current
at 230VAC
(mA)
Output
Output
Voltage Range Current
(VDC)
(mA)
Max
#
LEDs
RACD12-350
universal
200
3-36
350
10 x 1W
RACD12-500
universal
200
3-24
500
6 x 2W
RACD12-700
universal
200
3-17
700
4 x 2W, 8 x 1W
Specifications (typical at 25°C and after warm up time unless otherwise specified )
Input Voltage Range
Rated Power
Input Frequency Range
Power Factor
THD
90-264VAC
12 Watts max.
47-63 Hz
Full Load, 115VAC/230VAC
0.95
Full Load, 115VAC
7% max.
Full Load, 230VAC
14% max.
Open Circuit Voltage
350mA Version
42VDC
(Zener Clamp)
500mA Version
28VDC
700mA Version
24VDC
Inrush Current (<2mS)
115VAC/230VAC
10A max.
Input Current
230VAC, Full Load
200mA max.
Leakage Current
115VAC/240VAC - 60/50Hz
0.5mA typ.
Input Fuse
Standard
T1A
Output Current Accuracy
(combined Tolerance, Load Regulation and Line Regulation)
±10%.
Minimum Load
Open Circuit Protected
1 LED
Hold Up Time
18ms min.
Operating Frequency
50-120kHz typ.
Efficiency at Full Load
78%
RMS Isolation Voltage (input to output)
3kVAC / 1 minute
Temperature Coefficient
±0.02%/°C typ.
Overload Protection
120% typ.
Short Circuit Protection
Continuous Current Limit
Output Overvoltage Protection
Zener Diode Clamp
Overtemperature Protection
Shutdown, Automatic restart after cooling down
Operating Temperature Range
Ambient Temperature
-20°C to +50°C
(free air convection, according to CE/UL)
Case Temperature
81°C max.
Operating Temperature Range
Ambient Temperature
-20°C to +50°C
(free air convection, according to ENEC)
Case Temperature
85°C max.
Storage Temperature Range
-40°C to +100°C
Weight
100g
Packing Quantity
1pc
Humidity
95% RH max.
continued on next page
www.recom-power.com
REV: 1/2015
RoHS
2011/65/EU
6/6
E340696
UL-8750 Certified
cUL-8750 Certified
ENEC 61347 Certified
RACD12
Refer to Application Notes
L-25
RACD12
Series
LIGHTLINE
AC/DC-Converter
Specifications (typical at 25°C and after warm up time unless otherwise specified )
IP Rating
PCB Material
Case Material
Designed to meet Standards
IP20, Indoor Use Only
Plastic Resin with Fibreglass (UL94V-0)
Plastic
Electrical Lighting, EMC Emissions
EN55015:2006 + A1: 2007 + A2:2009
Limits for Harmonics Emissions
EN 61000-3-2:2006
EMC Compatability: Flicker and Voltage Variations
EN 61000-3-3:2006
Electrical Lighting: EMC Immunity
EN 61547:1995 + A1:2000
Class II Power Supply Safety
complies with UL1310
FCC
complies with FCC18A
<20%
LED Lighting Safety
UL8750
LED Lighting Safety (Canada)
cUL8750
RCM (U21381)
AS/NZS 61347.1:2002, IEC 61347-2-13
ENEC Certification, General Safety
EN 61347-1: 2008
ENEC Certification, Safety of AC supplied Control Gear for LED Modules
EN 61347-2-13: 2006
PSE
J61347-1(H20), J61347-2-13(H21), J55015(H20)
25°C ambient
>70 x 10³ hours in operation
AC Input
Screw terminal
LED Output
Screw Terminal
LED Output
5.5mm Socket with 2mm Pin (Suitable matching plug Switchcraft S760 or similar)*
THD
Certifications
Design Lifetime
Connections
Note:
All LED Drivers may not be used without a load. They must be switched on the primary side only. Noncompliance may damage the LED or reduce its lifetime.
Characteristic
RACD12
Maximum Number of LED drivers
per circuit breakers
Condition
115VAC, 1Ohm
90° phase angle
230VAC, 1Ohm
90° phase angle
277VAC, 1Ohm
90° phase angle
Circuit Breaker
Circuit Breaker Current
Typ
10A
16A
20A
25A
C
101
128
171
228
B
61
100
121
150
C
121
164
221
291
B
70
115
139
172
C
139
188
254
334
Package Style and Pinning
123
17
Connections
5.5mm socket
x 2.1mm
Tc
39
3.5mm dia.
15
51
45
Cable entry
with strain relief
CN1
Function
L
VAC in (L)
N
VAC in (N)
CN2
Function
+
LED+
-
LED-
5.5mm Socket* Function
117
Pin
LED+
2 Mounting screws are included
Shell
LED-
Tc= Case Temperature Measuring Point
Tolerenace
XX = +/-0.5mm
XX.X =+/-0.25mm
18
The product information and specifications are subject to change without prior notice. RECOM products are not authorized for use in safety-critical applications (such as life support) without RECOM’s explicit
written consent. A safety-critical application is defined as an application where a failure of a RECOM product may reasonably be expected to endanger or cause loss of life, inflict bodily harm or damage property. The buyer
shall indemnify and hold harmless RECOM, its affiliated companies and its representatives against any damage claims in connection with the unauthorized use of RECOM products in such safety-critical applications.
L-26
REV: 1/2015
www.recom-power.com