● ● ● ● ● ● ● ● ● Features LED DRIVER 20W Class II AC-DC LED Power Supply ENEC, UL, RCM and CB Certified Active Power Factor Correction >0.95 Fused Input, Protected Output 3kVAC Isolation cUL/UL8750 Certified, CE Marked Output Connector to avoid miswiring Low Cost Long 5 Year Warranty Description A compact 20W constant current switching power module suitable for driving high power LEDs (Vf = 3.6V). The output current is fixed at 350mA, 500mA, 700mA or 1050mA. Active power factor correction is standard. This series features both screw terminal and socket output connections. The socket connecter avoids the possibility of miswiring and damaging the LED load if the LEDs are preassembled into a wiring harness or lamp fitting. LIGHTLINE AC/DC-Converter with 5 year Warranty 20 Watt PFC Single Output Selection Guide Part Number Input Voltage Range (VAC) Input Current at full load (mA) Nom. Output Voltage Range (VDC) Output Current (mA) Max # LEDs RACD20-350 universal 260 6-56 350 15 x 1W RACD20-500 universal 260 6-40 500 11 x 2W RACD20-700 universal 260 6-29 700 8 x 2W, 8+8 x 1W RACD20-1050 universal 260 5-17 1050 6 x 3W, 5+5 x 2W Specifications (typical at 25°C and after warm up time unless otherwise specified ) Input Voltage Range Rated Power Input Frequency Range Power Factor THD Open Circuit Voltage (Zener Clamp) 90-264VAC 20 Watts max. 47-63 Hz Full Load, 115VAC/230VAC 0.95 Full Load, 115VAC/230VAC 12% max. 350mA Version 57VDC 500mA Version 43VDC 700mA Version 32VDC 1050mA Version 19VDC Inrush Current (<2mS) 115VAC/230VAC 10A max. Input Current 230VAC, Full Load 260mA typ. Leakage Current 115VAC/240VAC - 60/50Hz 0.5mA typ. Input Fuse Standard T1A Output Current Accuracy (combined Tolerance, load Regulation and Line Regulation) ±10% Minimum Load Open Circuit Protected 2 LEDs Hold Up Time 18ms min. Operating Frequency 40 - 100 kHz typ. Efficiency at Full Load 83% RMS Isolation Voltage (input to output) 3kVAC / 1 minute Temperature Coefficient ±0.02%/°C typ. Overload Protection 120% typ. Short Circuit Protection Continuous Current Limit Output Overvoltage Protection Zener Diode Clamp Overtemperature Protection Shutdown, Automatic restart after cooling down Operating Temperature Range Ambient Temperature -20°C to +50°C (free air convection, according to CE/UL) Case Temperature 78.6°C max. Operating Temperature Range Ambient Temperature -20°C to +50°C (free air convection, according to ENEC) Case Temperature 85°C max. Storage Temperature Range -40°C to +100°C Weight 160g Packing Quantity 1pc continued on next page www.recom-power.com Standard REV: 0/2015 RoHS 2011/65/EU 6/6 E340696 UL 8750 Certified cUL 8750 Certified* ENEC 61347 Certified RACD20 * RACD20-700 and -1050 only has cUL Refer to Application Notes L-27 RACD20 Series LIGHTLINE AC/DC-Converter Specifications (typical at 25°C and after warm up time unless otherwise specified ) Humidity IP Rating PCB Material Case Material Designed to meet Standards 95% RH max. IP20, Indoor Use Only Plastic Resin with Fibreglass (UL94V-0) Plastic Electrical Lighting, EMC Emissions EN55015:2006 + A1: 2007 + A2:2009 Limits for Harmonics Emissions EN 61000-3-2:2006 EMC Compatability: Flicker and Voltage Variations EN 61000-3-3:2006 Electrical Lighting: EMC Immunity EN 61547:1995 + A1:2000 Class II Power Supply Safety complies with UL1310 FCC complies with FCC18A <20% LED Lighting Safety (E340696) UL8750 LED Lighting Safety (Canada) cUL8750 (RACD20-700, RACD20-1050 only) RCM (U21380) AS/NZS 61347.1:2002, IEC 61347-2-13 ENEC CE Certification, General Safety EN 61347-1: 2008 ENEC CE Certification, Safety of AC supplied Control Gear for LED Modules EN 61347-2-13: 2006 PSE J61347-1(H20), J61347-2-13(H21), J55015(H20) 25°C ambient >70 x 10³ hours in operation AC Input Screw terminal LED Output Screw Terminal LED Output 5.5mm Socket with 2mm Pin (Suitable matching plug Switchcraft S760 or similar) THD Certifications Design Lifetime Connections Note: All LED Drivers may not be used without a load. They must be switched on the primary side only. Noncompliance may damage the LED or reduce its lifetime. Characteristic RACD20 Maximum Number of LED drivers per circuit breakers Condition Circuit Breaker Circuit Breaker Current Typ 10A 16A 20A 25A C 47 68 84 105 B 36 57 69 85 C 57 87 109 134 B 41 65 80 98 C 65 99 125 154 115VAC, 1Ohm 90° phase angle 230VAC, 1Ohm 90° phase angle 277VAC, 1Ohm 90° phase angle Package Style and Pinning 145 15 Tc 42 Connections 5.5mm socket +2.1mm 35 50 Cable entry with strain relief 3.5mm dia. Function L VAC in (L) N VAC in (N) CN2 Function + LED+ - LED- 5.5mm Socket* Function 137 2 Mounting screws are included 15 CN1 22 Tc=Case Temperature Measuring Point Pin LED+ Shell LED- Tolerance XX = +/-1mm XX.X = */-0.5mm The product information and specifications are subject to change without prior notice. RECOM products are not authorized for use in safety-critical applications (such as life support) without RECOM’s explicit written consent. A safety-critical application is defined as an application where a failure of a RECOM product may reasonably be expected to endanger or cause loss of life, inflict bodily harm or damage property. The buyer shall indemnify and hold harmless RECOM, its affiliated companies and its representatives against any damage claims in connection with the unauthorized use of RECOM products in such safety-critical applications. L-28 REV: 0/2015 www.recom-power.com