AN11066 SDARS active antenna 1st stage LNA with BFU730F, 2.33 GHz Rev. 1 — 25 October 2011 Application note Document information Info Content Keywords LNA, 2.33 GHz, BFU730F, SDARS. Abstract This document provides circuit, layout, BOM and performance information for 2.33 GHz LNA equipped with NXP Semiconductors BFU730F wide-band transistor. AN11066 NXP Semiconductors SDARS active antenna 1st stage LNA with BFU730F, 2.33 GHz Revision history Rev Date Description v.1 20111025 Initial version Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: [email protected] AN11066_1 Application note All information provided in this document is subject to legal disclaimers. Rev. 1 — 25 October 2011 © NXP B.V. 2011. All rights reserved. 2 of 20 AN11066 NXP Semiconductors SDARS active antenna 1st stage LNA with BFU730F, 2.33 GHz 1. Introduction The BFU730F is a wideband Silicon Germanium Amplifier transistor for high speed, low noise applications. It is used for LNA applications such as GPS, satellite radio, cordless phone and wireless LAN. The BFU730F comes in a SOT343F package that contains two emitter pins for improved grounding. The BFU730F is ideal in all kinds of application where cost matters. It also provides the designer with increased flexibility. BFU730F SiGeC low noise transistor is shown in Figure 1 in a Satellite Digital Audio Radio Service (SDARS) active antenna LNA application. It is intended for use as the first stage in a three stage SIRIUS LNA chain. SDARS Active Antenna LNA 2320-2332.5 (SIRIUS, 3 Stages) NXP BFU730F G = 17.6 dB lDC = 11mA NF = 0.8 dB P1dB = +1.8 dBm NXP Bandpass BFU690F Filter G = 15.3 dB lDC = 30 mA NF = 1.47 dB P1dB = +13.9 dBm NXP BFU aaa-000708 Fig 1. Overview of SDARS active antenna LNA The 2.33 GHz LNA evaluation board (EVB) is designed to evaluate the performance of the BFU730F transistor applied as the first stage in a three stage SIRIUS LNA chain. This document provides an application diagram, board layout, bill of material, and some typical results. Figure 2 depicts the evaluation board. AN11066_1 Application note All information provided in this document is subject to legal disclaimers. Rev. 1 — 25 October 2011 © NXP B.V. 2011. All rights reserved. 3 of 20 AN11066 NXP Semiconductors SDARS active antenna 1st stage LNA with BFU730F, 2.33 GHz aaa-000709 Fig 2. AN11066_1 Application note BFU730F 2.33 GHz LNA evaluation board All information provided in this document is subject to legal disclaimers. Rev. 1 — 25 October 2011 © NXP B.V. 2011. All rights reserved. 4 of 20 AN11066 NXP Semiconductors SDARS active antenna 1st stage LNA with BFU730F, 2.33 GHz 2. General description The BFU730F is a discrete HBT produced in NXP Semiconductors SiGeC QuBIC4x BiCmos process. SiGeC is in principle a normal silicon germanium process with the addition of Carbon in the base layer of the NPN transistor. The presence of carbon in the base layer suppresses the boron diffusion during wafer processing. This process allows steeper and narrower SiGe HBT base and a heavier doped base. This results in lower base resistance, lower noise and higher cut-off frequency (higher gain). Table 1 provides a summary of the transistor performance in terms of noise and gain is shown. Table 1. BFU730F values, measured at, 2 V, Vce and 5 mA IC Frequency (GHz) Noise (dB) Associated gain (dB) 1.5 0.50 25 1.8 0.50 23.5 2.4 0.55 21.5 5.8 0.80 15.0 12 1.30 11.0 Table 2. Pinning information Pin Description 1 emitter 2 base 3 emitter 4 collector Simplified outline 3 Graphic symbol 4 4 2 1, 3 2 AN11066_1 Application note All information provided in this document is subject to legal disclaimers. Rev. 1 — 25 October 2011 1 mbb159 © NXP B.V. 2011. All rights reserved. 5 of 20 AN11066 NXP Semiconductors SDARS active antenna 1st stage LNA with BFU730F, 2.33 GHz 3. Application Board The BFU730F 2.33 GHz EVB simplifies the evaluation of the BFU730F wideband transistor, for this frequency range. The EVB enables testing of the device performance and requires no additional support circuitry. The board is fully assembled with BFU730F, including input and output matching, to optimize the performance. The input match was a compromise between the best noise figure and a low input return loss. The board is mounted with signal input and output SMA connectors for connection to RF test equipment. 3.1 Application Circuit Figure 3 provides the application diagram as supplied on the evaluation board. Vcc = 3.3 V X3 R1 C5 R2 C3 R4 C4 L2 R3 R5 L1 RF in RF out C2 C1 BFU730F L3 X2 X1 aaa-000710 Fig 3. AN11066_1 Application note Circuit diagram of the evaluation board All information provided in this document is subject to legal disclaimers. Rev. 1 — 25 October 2011 © NXP B.V. 2011. All rights reserved. 6 of 20 AN11066 NXP Semiconductors SDARS active antenna 1st stage LNA with BFU730F, 2.33 GHz 3.2 Board Layout Figure 3 shows the board layout including components. aaa-000711 Fig 4. Printed circuit board of the BUF730F 2.33 GHz evaluation board 3.3 PCB layout A good PCB Layout is an essential part of an RF circuit design. The EVB of the BFU730F serves as a guideline for laying out a board using the BFU730F. Use controlled impedance lines for all high frequency inputs and outputs. Bypass VCC with decoupling capacitors, preferable located as close as possible to the device. For long bias lines, it may be necessary to add decoupling capacitors in the line further away from the device. Correct grounding of the GND pin is also essential for performance. Either connect the GND pin directly to the ground plane or through vias, or do both. The EVB is made of FR4 material using the stack shown in Figure 5. 17 µm Cu 0.25 mm FR4 Critical 17 µm Cu 0.50 mm FR4 only for mechanical rigidity of PCB 17 µm Cu 0.25 mm FR4 only for mechanical rigidity of PCB 17 µm Cu aaa-000712 Fig 5. AN11066_1 Application note Stack of the PCB material All information provided in this document is subject to legal disclaimers. Rev. 1 — 25 October 2011 © NXP B.V. 2011. All rights reserved. 7 of 20 AN11066 NXP Semiconductors SDARS active antenna 1st stage LNA with BFU730F, 2.33 GHz Material supplier is Isola Duraver; r = 4.6 to 4.9: T= 0.02. 3.4 Bill of materials Table 3. Bill of materials Designator Description Footprint Value Supplier name/type Comment C1 capacitor 0402 12 pF Murata GRM1555 input matching/DC blocking C2 capacitor 0402 3.3 pF Murata GRM1555 input matching/DC blocking C3 capacitor 0402 8.2 pF Murata GRM1555 LF decoupling C4 capacitor 0402 10 pF Murata GRM1555 LF decoupling C5 capacitor 0402 10 pF Murata GRM1555 LF decoupling L1 inductor 0402 15 nH Murata/LQW15A high Q low Rs input matching/DC bias L2 inductor 0402 100 nH Murata/LQW15A L3 inductor 0402 5.8 nH Murata/LQW15A high Q low Rs output matching R1 resistor 0402 130 various bias setting temperature stability R2 resistor 0402 30 various bias setting R3 resistor 0402 100 various stability R4, R5 resistor 0402 0 various backup tune pads X1, X2 SMA RF connector - - Johnson, end launch SMA 142-0701-841 RF input/RF output X3 DC header - - Molex, PCB header, right angle, bias connector 1 row, 3-way 90121-0763 AN11066_1 Application note All information provided in this document is subject to legal disclaimers. Rev. 1 — 25 October 2011 DC bias © NXP B.V. 2011. All rights reserved. 8 of 20 AN11066 NXP Semiconductors SDARS active antenna 1st stage LNA with BFU730F, 2.33 GHz 4. Equipment required In order to measure the evaluation board the following is required: • DC power supply up to 30 mA at 3.3 V (up to 15 V for bias control) • RF signal generator capable of generating an RF signal at the operating frequency of 2.33 GHz. • RF spectrum analyzer that covers at least the operating frequency of 2.33 GHz as well as a few of the harmonics. A spectrum analyzer that has a noise figure test function which measures up to 8 GHz, is sufficient. This is useful as it eliminates the necessity of having an expensive noise figure analyzer. • Ammeter to measure the supply current (optional). • Network analyzer for measuring gain, return loss and reverse Isolation. • Noise figure analyzer. AN11066_1 Application note All information provided in this document is subject to legal disclaimers. Rev. 1 — 25 October 2011 © NXP B.V. 2011. All rights reserved. 9 of 20 AN11066 NXP Semiconductors SDARS active antenna 1st stage LNA with BFU730F, 2.33 GHz 5. Connections and setup The BFU730F, 2.33 GHz EVB is fully assembled and tested. The following procedure is a step-by-step guide to operate the EVB and test the device functions. 1. Set the DC power supply to 3.3 V and connect it to the VCC and GND terminals. 2. Connect the RF signal generator and spectrum analyzer to the RF input and the RF output of the EVB, respectively. Do not turn on the RF output of the signal generator yet but set it to 30 dBm output power at 2.33 GHz. Set the spectrum analyzer to 2.33 GHz center frequency with a reference level of 0 dBm. 3. Turn on the DC power supply and it reads approximately 11 mA. 4. Enable the RF output of the generator; the Spectrum analyzer displays a tone of 2.33 GHz at around 13 dBm. 5. A network analyzer (NWA) can be used, instead of a signal generator and spectrum analyzer, to measure gain for input and output return loss 6. To evaluate the noise figure, use either a noise figure analyzer or a spectrum analyzer with noise option. The use of a 15 dB noise source, such as the Agilent 364B, is recommended. When measuring the noise figure of the evaluation board, minimize the use of any kind of adaptors or cables between the noise source and the EVB. Cables and adaptors significantly affect the noise performance. aaa-000713 Fig 6. AN11066_1 Application note Printed circuit board of the BUF730F 2.33 GHz evaluation board All information provided in this document is subject to legal disclaimers. Rev. 1 — 25 October 2011 © NXP B.V. 2011. All rights reserved. 10 of 20 AN11066 NXP Semiconductors SDARS active antenna 1st stage LNA with BFU730F, 2.33 GHz 6. Typical EVB Results Table 4. Typical measurement results measured on the evaluation board[1] Symbol Parameter value Unit NF noise figure 0.8 dB Gp power gain 17.6 dB RLin input return loss 9.4 dB RLout output return loss 22.5 dB isol(r) reverse isolation 29.4 dB Pi(1dB) input 1 dB Gain Compression 15 dBm PL(1dB) output 1 dB Gain Compression 1.7 dBm IP3I Input third order intercept point 4.7 dBm IP3O output third order intercept point 22.6 dBm [1] The NF and gain figures are measured at the SMA connectors of the EVB, so the connectors and PCB losses are not subtracted. When they are subtracted, the NF improves by approximately 0.1 dB. 6.1 Noise figure aaa-000714 2290 MHz to 2370 MHz, center of plot (x-axis) is 2330 MHz Fig 7. AN11066_1 Application note Plot of noise figure All information provided in this document is subject to legal disclaimers. Rev. 1 — 25 October 2011 © NXP B.V. 2011. All rights reserved. 11 of 20 AN11066 NXP Semiconductors SDARS active antenna 1st stage LNA with BFU730F, 2.33 GHz 6.1.1 Noise figure tabular data Table 5. Frequency list results[1] RF (GHz) NF (dB) Noise temperature (K) Gain (dB) 2.290 0.825 60.701 17.736 2.300 0.827 60.840 17.694 2.310 0.825 60.650 17.662 2.320 0.832 61.259 17.639 2.330 0.822 60.425 17.644 2.340 0.821 60.378 17.641 2.350 0.812 59.642 17.643 2.360 0.834 61.426 17.632 2.370 0.819 60.216 17.609 [1] From Rohde and Schwarz FSU 6.2 Power gain compression test Vcc = 3.3 V network analyzer is set to CW mode - for example, set to a single frequency, with power sweep. Input power is swept from 25 dBm to 5 dBm at 2332.5 MHz. Amplifier reaches input 1 dB compression point (Pi(1dB)) at 15.02 dBm input power. Output PL(1dB) = 15.02 dBm + 16.77 dB gain at PL(1dB) point +1.75 dBm, or 1.5 mW. aaa-000715 Fig 8. AN11066_1 Application note Plot of gain compression test All information provided in this document is subject to legal disclaimers. Rev. 1 — 25 October 2011 © NXP B.V. 2011. All rights reserved. 12 of 20 AN11066 NXP Semiconductors SDARS active antenna 1st stage LNA with BFU730F, 2.33 GHz 6.3 Input return losses (10 MHz to 6 GHz) 6.3.1 Log Mag aaa-000716 Fig 9. Plot of input return losses 6.3.2 Smith chart aaa-000717 Reference plain = input SMA connector on PCB Fig 10. Smith chart of input return losses AN11066_1 Application note All information provided in this document is subject to legal disclaimers. Rev. 1 — 25 October 2011 © NXP B.V. 2011. All rights reserved. 13 of 20 AN11066 NXP Semiconductors SDARS active antenna 1st stage LNA with BFU730F, 2.33 GHz 6.3.3 Forward gain - wide sweep aaa-000718 Fig 11. Plot of forward gain 6.4 Reverse isolation aaa-000719 Fig 12. Plot of reverse isolation AN11066_1 Application note All information provided in this document is subject to legal disclaimers. Rev. 1 — 25 October 2011 © NXP B.V. 2011. All rights reserved. 14 of 20 AN11066 NXP Semiconductors SDARS active antenna 1st stage LNA with BFU730F, 2.33 GHz 6.5 Output return losses (10 MHz to 6 GHz) 6.5.1 Log Mag aaa-000720 Fig 13. Plot of output return losses 6.5.2 Smith chart aaa-000721 Reference plain = input SMA connector on PCB Fig 14. Smith chart of output return losses AN11066_1 Application note All information provided in this document is subject to legal disclaimers. Rev. 1 — 25 October 2011 © NXP B.V. 2011. All rights reserved. 15 of 20 AN11066 NXP Semiconductors SDARS active antenna 1st stage LNA with BFU730F, 2.33 GHz 6.6 Two-tone test (2332 MHz) 6.6.1 Input stimulus for amplifier two-tone test • f1 = 2332 MHz • f2 = 2333 MHz • 24.37 dBm for each tone aaa-000722 Fig 15. Plot of amplifier two-tone test at 2332 MHz AN11066_1 Application note All information provided in this document is subject to legal disclaimers. Rev. 1 — 25 October 2011 © NXP B.V. 2011. All rights reserved. 16 of 20 AN11066 NXP Semiconductors SDARS active antenna 1st stage LNA with BFU730F, 2.33 GHz 6.6.2 LNA response to two-tone test • Output IP3 = 22.625 dBm • Input IP3 = 22.625 dBm (24.37 6.46) dBm = 4.7 dBm aaa-000723 Fig 16. Plot of LNA response to two-tone test AN11066_1 Application note All information provided in this document is subject to legal disclaimers. Rev. 1 — 25 October 2011 © NXP B.V. 2011. All rights reserved. 17 of 20 AN11066 NXP Semiconductors SDARS active antenna 1st stage LNA with BFU730F, 2.33 GHz 7. Legal information 7.1 Definitions Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. 7.2 Disclaimers Limited warranty and liability — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors’ aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. Right to make changes — NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use — NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications — Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using NXP Semiconductors products, and NXP Semiconductors accepts no liability for any assistance with applications or customer product AN11066_1 Application note design. It is customer’s sole responsibility to determine whether the NXP Semiconductors product is suitable and fit for the customer’s applications and products planned, as well as for the planned application and use of customer’s third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer’s applications or products, or the application or use by customer’s third party customer(s). Customer is responsible for doing all necessary testing for the customer’s applications and products using NXP Semiconductors products in order to avoid a default of the applications and the products or of the application or use by customer’s third party customer(s). NXP does not accept any liability in this respect. Export control — This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from competent authorities. Evaluation products — This product is provided on an “as is” and “with all faults” basis for evaluation purposes only. NXP Semiconductors, its affiliates and their suppliers expressly disclaim all warranties, whether express, implied or statutory, including but not limited to the implied warranties of non-infringement, merchantability and fitness for a particular purpose. The entire risk as to the quality, or arising out of the use or performance, of this product remains with customer. In no event shall NXP Semiconductors, its affiliates or their suppliers be liable to customer for any special, indirect, consequential, punitive or incidental damages (including without limitation damages for loss of business, business interruption, loss of use, loss of data or information, and the like) arising out the use of or inability to use the product, whether or not based on tort (including negligence), strict liability, breach of contract, breach of warranty or any other theory, even if advised of the possibility of such damages. Notwithstanding any damages that customer might incur for any reason whatsoever (including without limitation, all damages referenced above and all direct or general damages), the entire liability of NXP Semiconductors, its affiliates and their suppliers and customer’s exclusive remedy for all of the foregoing shall be limited to actual damages incurred by customer based on reasonable reliance up to the greater of the amount actually paid by customer for the product or five dollars (US$5.00). The foregoing limitations, exclusions and disclaimers shall apply to the maximum extent permitted by applicable law, even if any remedy fails of its essential purpose. 7.3 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. All information provided in this document is subject to legal disclaimers. Rev. 1 — 25 October 2011 © NXP B.V. 2011. All rights reserved. 18 of 20 AN11066 NXP Semiconductors SDARS active antenna 1st stage LNA with BFU730F, 2.33 GHz 8. Tables Table 1. Table 2. Table 3. BFU730F values, measured at, 2 V, Vce and 5 mA IC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Pinning information . . . . . . . . . . . . . . . . . . . . . . .5 Bill of materials . . . . . . . . . . . . . . . . . . . . . . . . .8 Table 4. Table 5. Typical measurement results measured on the evaluation board[1] . . . . . . . . . . . . . . . . . . . 11 Frequency list results[1] . . . . . . . . . . . . . . . . . . 12 9. Figures Fig 1. Fig 2. Fig 3. Fig 4. Fig 5. Fig 6. Fig 7. Fig 8. Fig 9. Fig 10. Fig 11. Fig 12. Fig 13. Fig 14. Fig 15. Fig 16. Overview of SDARS active antenna LNA . . . . . . .3 BFU730F 2.33 GHz LNA evaluation board . . . . . .4 Circuit diagram of the evaluation board . . . . . . . . .6 Printed circuit board of the BUF730F 2.33 GHz evaluation board . . . . . . . . . . . . . . . . . .7 Stack of the PCB material . . . . . . . . . . . . . . . . . . .7 Printed circuit board of the BUF730F 2.33 GHz evaluation board . . . . . . . . . . . . . . . . .10 Plot of noise figure . . . . . . . . . . . . . . . . . . . . . . . . 11 Plot of gain compression test. . . . . . . . . . . . . . . .12 Plot of input return losses . . . . . . . . . . . . . . . . . .13 Smith chart of input return losses . . . . . . . . . . . .13 Plot of forward gain . . . . . . . . . . . . . . . . . . . . . . .14 Plot of reverse isolation . . . . . . . . . . . . . . . . . . . .14 Plot of output return losses . . . . . . . . . . . . . . . . .15 Smith chart of output return losses . . . . . . . . . . .15 Plot of amplifier two-tone test at 2332 MHz . . . . .16 Plot of LNA response to two-tone test . . . . . . . . .17 AN11066_1 Application note All information provided in this document is subject to legal disclaimers. Rev. 1 — 25 October 2011 © NXP B.V. 2011. All rights reserved. 19 of 20 AN11066 NXP Semiconductors SDARS active antenna 1st stage LNA with BFU730F, 2.33 GHz 10. Contents 1 2 3 3.1 3.2 3.3 3.4 4 5 6 6.1 6.1.1 6.2 6.3 6.3.1 6.3.2 6.3.3 6.4 6.5 6.5.1 6.5.2 6.6 6.6.1 6.6.2 7 7.1 7.2 7.3 8 9 10 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 General description . . . . . . . . . . . . . . . . . . . . . . 5 Application Board . . . . . . . . . . . . . . . . . . . . . . . 6 Application Circuit . . . . . . . . . . . . . . . . . . . . . . . 6 Board Layout . . . . . . . . . . . . . . . . . . . . . . . . . . 7 PCB layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Bill of materials . . . . . . . . . . . . . . . . . . . . . . . . . 8 Equipment required . . . . . . . . . . . . . . . . . . . . . . 9 Connections and setup . . . . . . . . . . . . . . . . . . 10 Typical EVB Results . . . . . . . . . . . . . . . . . . . . 11 Noise figure . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Noise figure tabular data. . . . . . . . . . . . . . . . . 12 Power gain compression test . . . . . . . . . . . . . 12 Input return losses (10 MHz to 6 GHz) . . . . . . 13 Log Mag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Smith chart . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Forward gain - wide sweep. . . . . . . . . . . . . . . 14 Reverse isolation . . . . . . . . . . . . . . . . . . . . . . 14 Output return losses (10 MHz to 6 GHz) . . . . 15 Log Mag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Smith chart . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Two-tone test (2332 MHz) . . . . . . . . . . . . . . . 16 Input stimulus for amplifier two-tone test . . . . 16 LNA response to two-tone test . . . . . . . . . . . . 17 Legal information. . . . . . . . . . . . . . . . . . . . . . . 18 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. © NXP B.V. 2011. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: [email protected] Date of release: 25 October 2011 Document identifier: AN11066_1