TDA8596 I2C-bus controlled 4 × 45 W power amplifier with symmetrical inputs Rev. 02 — 8 November 2007 Product data sheet 1. General description The TDA8596 is a quad Bridge Tied Load (BTL) audio power amplifier with symmetrical inputs, made in BCDMOS technology. It contains four independent amplifier channels in BTL configuration with complementary (PMOST/NMOST) output stages. Temperature warning and output signal clipping diagnosis is possible via the I2C-bus and via the diagnostic pins (DIAG and STB pin). The temperature pre-warning level and clip detection levels can be programmed via the I2C-bus. The status of each amplifier channel (i.e. output offset, load connected or not, short circuit condition at the output pins) can be read out separately. 2. Features 2.1 General n n n n n n n n n n n n n Operates in legacy mode (non I2C-bus) and I2C-bus mode (3.3 V and 5 V compliant) Three hardware-programmable I2C-bus addresses Drives 4 Ω or 2 Ω loads Balanced/symmetrical inputs Speaker fault detection Programmable gain (26 dB and 16 dB) also available in legacy mode Independent short circuit protection per channel Loss of ground and loss of VP safe (with 300 mΩ series impedance and a maximum supply decoupling capacitor of 2200 µF) All outputs are short-circuit proof to ground, supply voltage and across the load All pins are short circuit proof to ground Temperature-controlled gain reduction to prevent audio holes at high junction temperatures Low battery voltage detection Qualified in accordance with AEC-Q100 2.2 I2C-bus mode n DC load detection: open (no load), normal load, line-driver load n AC load (tweeter) detection n Detect which load is connected during start-up to allow the system to be configured to select the gain accordingly (e.g. line-driver mode or normal mode). n Independently selectable soft mute of front (channel 1 and channel 3) and rear channels (channel 2 and channel 4) TDA8596 NXP Semiconductors I2C-bus controlled 4 × 45 W power amplifier with symmetrical inputs n Independently programmable gain (26 dB and 16 dB) of front (channel 1 and channel 3) and rear (channel 2 and channel 4) channels n Flexible programmable diagnostic levels: u Programmable clip detect: 2 %, 5 % or 10 % u Programmable thermal pre-warning n Selectable information on the DIAG or STB pin: u The STB pin can be programmed/multiplexed with second clip detection u Clip information of each channel separately can be directed to the DIAG pin or the STB pin u Independent enabling of thermal-, clip- or load fault (short across the load, to VP or to ground) available on the DIAG pin n Offset detection 3. Quick reference data Table 1. Quick reference data Symbol Parameter Conditions Min Typ Max Unit VP supply voltage RL = 4 Ω 8 14.4 18 V Iq quiescent current no load - 270 400 mA Po output power RL = 4 Ω; VP = 14.4 V; maximum power; Vi = 2 V (RMS) square wave 37 40 - W RL = 4 Ω; VP = 14.4 V; THD = 0.5 % 18 20 - W RL = 4 Ω; VP = 14.4 V; THD = 10 % 23 25 - W RL = 2 Ω; VP = 14.4 V; maximum power; Vi = 2 V (RMS) square wave 58 64 - W - 0.01 0.1 % normal mode; Tamb = 25 °C to 105 °C - 45 65 µV normal mode; Tamb = −20 °C to 25 °C - 45 110 µV line driver mode - 22 29 µV THD total harmonic distortion RL = 4 Ω; f = 1 kHz; Po = 1 W to 12 W Vn(o) noise output voltage filter 20 Hz to 22 kHz; RS = 1 kΩ 4. Ordering information Table 2. Ordering information Type number Package TDA8596TH Name Description Version HSOP36 plastic, heatsink small outline package; 36 leads; low stand-off height SOT851-2 TDA8596_2 Product data sheet © NXP B.V. 2007. All rights reserved. Rev. 02 — 8 November 2007 2 of 48 TDA8596 NXP Semiconductors I2C-bus controlled 4 × 45 W power amplifier with symmetrical inputs 5. Block diagram SCL ADSEL SDA 28 21 26 VP2 VP1 19, 20 34, 35 33 STB IN3+ 29 STANDBY/ FAST MUTE I2C-BUS 13 18 26 dB/ 16 dB MUTE IN3− DIAG SELECT DIAGNOSTIC/ CLIP DETECT 14 17 OUT3+ OUT3− PROTECTION/ DIAGNOSTIC IN1+ 7 IN1− 4 26 dB/ 16 dB MUTE 6 2 OUT1+ OUT1− PROTECTION/ DIAGNOSTIC IN4+ 11 IN4− 25 26 dB/ 16 dB MUTE 12 23 OUT4+ OUT4− PROTECTION/ DIAGNOSTIC IN2+ 9 IN2− 30 26 dB/ 16 dB MUTE 8 32 OUT2+ OUT2− PROTECTION/ DIAGNOSTIC VP 36 TDA8596 27 SVR 10 SGND 22 GAINSEL 3 PGND1 31 PGND2 16 PGND3 24 TAB 001aaf998 PGND4 Fig 1. Block diagram TDA8596_2 Product data sheet © NXP B.V. 2007. All rights reserved. Rev. 02 — 8 November 2007 3 of 48 TDA8596 NXP Semiconductors I2C-bus controlled 4 × 45 W power amplifier with symmetrical inputs 6. Pinning information 6.1 Pinning TAB 36 1 n.c. VP2 35 2 OUT1− VP2 34 3 PGND1 DIAG 33 4 OUT1+ OUT2− 32 5 n.c. PGND2 31 6 IN1− OUT2+ 30 7 IN1+ STB 29 8 IN2− ADSEL 28 9 IN2+ TDA8596TH SVR 27 10 SGND SDA 26 11 IN4+ OUT4+ 25 12 IN4− PGND4 24 13 IN3+ OUT4− 23 14 IN3− 15 n.c. GAINSEL 22 SCL 21 16 PGND3 VP1 20 17 OUT3− VP1 19 18 OUT3+ 001aaf999 Fig 2. Pin configuration 6.2 Pin description Table 3. Pin description Symbol Pin Description n.c. 1 not connected OUT1− 2 channel 1 negative output PGND1 3 power ground channel 1 OUT1+ 4 channel 1 positive output n.c. 5 not connected IN1− 6 channel 1 negative input IN1+ 7 channel 1 positive input IN2− 8 channel 2 negative input IN2+ 9 channel 2 positive input SGND 10 signal ground IN4+ 11 channel 4 positive input IN4− 12 channel 4 negative input IN3+ 13 channel 3 positive input IN3− 14 channel 3 negative input n.c. 15 not connected TDA8596_2 Product data sheet © NXP B.V. 2007. All rights reserved. Rev. 02 — 8 November 2007 4 of 48 TDA8596 NXP Semiconductors I2C-bus controlled 4 × 45 W power amplifier with symmetrical inputs Table 3. Pin description …continued Symbol Pin Description PGND3 16 power ground channel 3 OUT3− 17 channel 3 negative output OUT3+ 18 channel 3 positive output VP1 19 and 20 supply voltage 1 SCL 21 I2C-bus clock input GAINSEL 22 gain select input (legacy mode only) OUT4− 23 channel 4 negative output PGND4 24 power ground channel 4 OUT4+ 25 channel 4 positive output SDA 26 I2C-bus data input/output SVR 27 half supply filter capacitor ADSEL 28 I2C-bus address select STB 29 standby (I2C-bus mode) or mode pin (legacy mode); programmable second clip indicator OUT2+ 30 channel 2 positive output PGND2 31 power ground channel 2 OUT2− 32 channel 2 negative output DIAG 33 diagnostic/clip detection output VP2 34 and 35 supply voltage 2 TAB 36 heatsink connection; must be connected to ground 7. Functional description The TDA8596 is a quad BTL audio power amplifier with symmetrical inputs, made in BCDMOS technology. It contains four independent amplifier channels in BTL configuration with complementary (PMOST/NMOST) output stages (see Figure 1). The status of each amplifier channel (output offset, connected load, short circuit condition at output pins) can be read out separately via the I2C-bus. The TDA8596 is protected against overvoltage on the supply pins, short circuits at the output pins, overheating and loss-of-ground or loss-of-VP conditions. The temperature pre-warning level and the clip detection levels can be programmed via the I2C-bus. Further, the information that will be available on the diagnostic pins (i.e. DIAG or STB) can be programmed. Three different I2C-bus addresses can be selected by connecting a resistor to the ADSEL pin. In case the ADSEL pin is shorted to ground, the TDA8596 operates in legacy mode. In this mode no I2C-bus is needed and the STB pin will change from a two level pin (Standby mode and Operating mode) to a three level pin (Standby, Mute operating and Normal operating mode). TDA8596_2 Product data sheet © NXP B.V. 2007. All rights reserved. Rev. 02 — 8 November 2007 5 of 48 TDA8596 NXP Semiconductors I2C-bus controlled 4 × 45 W power amplifier with symmetrical inputs 7.1 Output stage The output stage of each amplifier channel consists of two PMOS power transistors and two NMOS transistors in BTL configuration. The TDA8596 is manufactured in a BCDMOS process on an isolated substrate Silicon On Insulator (SOI). Due to the absence of a doped (bulk) substrate, this process is insensitive to latch-up induced by substrate coupled parasitic paths. 7.2 Gain selection The gain of the TDA8596 can be programmed at 16 dB (line driver mode) or 26 dB (Normal operating mode). This can be done either in I2C-bus mode by means of a bus command or in legacy mode by using the GAINSEL pin. To allow this, the device must first be put in legacy mode by connecting the ADSEL pin to ground. In case the GAINSEL pin is connected to ground the 26 dB mode is selected. By leaving the GAINSEL pin open the 16 dB mode is selected. The GAINSEL pin will be ignored in I2C-bus mode. 7.3 Distortion (clip-) detection If the output of an amplifier channel starts clipping to either the supply voltage or to ground the output signal will become distorted. When the Total Harmonic Distortion (THD) per channel exceeds a preselected threshold (2 %, 5 % or 10 %), one of the two diagnostic pins (DIAG or STB) will be pulled LOW. The clip information of each channel can be directed separately to one specific diagnostic pin. This way, it is possible to distinguish between clipping on the front or rear channels. Redirection of temperature and load information to the diagnostic pins can be disabled to allow only the clip information to be present on these pins. In this mode, the temperature and load information is still available but can only be read out through the I2C-bus. Note: during mute-to-on or on-to-mute transitions, the clip detection may be activated even when no output clipping occurs. 7.4 Output protection and short circuit operation When a short circuit to ground, to VP or across the load occurs, the concerning amplifier channel will switch off. After 16 ms of non-operation it will switch on again. If the short circuit condition is still present the amplifier channel will again return to 16 ms of non-operation. The 16 ms cycle will reduce the dissipation. The other amplifier channels (without short circuit condition) will retain functionality. To prevent audible distortion, the amplifier channel with the short circuit condition can be disabled via the I2C-bus. In case the diagnostic pin is selected for load fault information (IB2[D4] = 0), it will be pulled LOW. Via the I2C-bus it can be read out which channel is shorted by what type of short circuit (to ground, to VP or across the load). In order to detect a shorted load, a signal should be applied to the inputs of the amplifier. A shorted load is only detected when the output current level on the related output crosses the defined Safe Operating ARea (SOAR) protection threshold. TDA8596_2 Product data sheet © NXP B.V. 2007. All rights reserved. Rev. 02 — 8 November 2007 6 of 48 TDA8596 NXP Semiconductors I2C-bus controlled 4 × 45 W power amplifier with symmetrical inputs 7.4.1 SOAR protection The output transistors are protected by a Safe Operating ARea (SOAR) protection. The TDA8596 has a two-stage SOAR protection: • If the differential output voltage across the load (Vo) is less than 1 V, and the current through the load (IL) exceeds 4 A, the amplifier channel will be switched off during 16 ms. To prevent spurious switch-off events (which may occur for instance in case of inductive loads or very high input signals), the fault condition (Vo < 1 V and IL > 4 A) must exist for more than 300 µs. • If the differential output voltage across the load (Vo) is more than 1 V, and the current through the load (IL) exceeds 8 A, the amplifier channel will be switched off during 16 ms. 7.4.2 Speaker protection To prevent damage of the speaker when one side of the speaker is connected to ground, a missing-current protection is implemented. When the current in the high side power transistor of one amplifier channel is not equal to the current through the corresponding low side power transistor, a fault condition is assumed and the concerning channel will be switched off. The boundary conditions for the activation of this speaker protection are: • Vo < 1.55 V and Imissing > 1 A for 80 µs • Vo > 1.55 V and Imissing > 3 A for 80 µs 7.5 Standby and mute operation The functionality of the STB pin depends on the mode of operation of the device (i.e. legacy- or I2C-bus mode). 7.5.1 I2C-bus mode When the STB pin is LOW (< 1 V), the device is in standby condition. The I2C-bus lines will not be loaded and the quiescent current will be low. When the STB pin is switched HIGH (> 2.5 V) the TDA8596 switches to operating condition and performs a Power-On Reset (POR). This will cause the DIAG pin to be pulled LOW. The TDA8596 will start-up when bit D0 of instruction byte IB1 is set. Bit D0 will also reset the ‘power-on reset occurred’ bit (DB2[D7]) and releases the DIAG pin. The soft- and fast-mute functions can be activated by means of I2C-bus instructions. The soft mute can be activated independently for the front (1 and 3) and rear (2 and 4) channels, and mutes the audio in 20 ms. The fast mute is activated for all channels simultaneously and mutes the audio in 0.1 ms. Releasing the mute will always occur via a soft mute and will take 20 ms. When the STB pin is switched LOW and the amplifier is in Operating mode, the fast mute will be activated prior to shut-down. This enables the option to fast mute the amplifier by means of the STB pin in case of, for instance an engine start, thus preventing audible pop noise. 7.5.2 Legacy mode (pin ADSEL connected to ground) In legacy mode, the function of the STB pin changes into a three level (standby, mute and operating) enable pin and the amplifier will directly start-up when the STB pin is put into Mute or Normal operating mode. Mute operation is controlled through an internal timer TDA8596_2 Product data sheet © NXP B.V. 2007. All rights reserved. Rev. 02 — 8 November 2007 7 of 48 TDA8596 NXP Semiconductors I2C-bus controlled 4 × 45 W power amplifier with symmetrical inputs (20 ms) to minimize mute-to-operating pops. When the STB pins directly switched from Normal operating to Standby mode, the fast mute (mutes in 0.1 ms) will be activated prior to shut-down. 7.6 Start-up and shut-down sequence To prevent the amplifier from producing switch-on and switch-off pop noise, the capacitor on the SVR pin is used for smooth start-up and shut-down sequences. Larger capacitors will lead to longer (smoother) start-up and shut-down sequences. Initially the amplifier outputs are charged to Half Supply Voltage (HVP) minus 1.4 V in mute condition. This is independent of the I2C-bus mute settings in I2C-bus mode or the pin STB voltage in legacy mode. The remaining 1.4 V before the outputs reach HVP, is used for mute release in case the I2C-bus bits (IB2[D2:D0] = 000) have been programmed to mute-off (or VSTB > 6.5 V in legacy mode). In case the I2C-bus bits have been programmed to maintain mute condition (IB2[D2:D0] = 111) (or 2.5 V < VSTB < 6.5 V in legacy mode) the amplifier will stay in mute. When the STB pin is switched LOW (< 1 V), a fast mute is performed prior to discharging the capacitor on pin SVR. With a capacitor of 22 µF the device goes into Standby mode (low quiescent current) within 1 s after switching STB to LOW (see also Figure 3 and Figure 6). Start-up and shut-down pop noise can be further reduced by activating the low pop mode. When this mode is selected (IB2[D3] = 0), the output voltage rising slope will decrease (resulting in a longer start-up time). TDA8596_2 Product data sheet © NXP B.V. 2007. All rights reserved. Rev. 02 — 8 November 2007 8 of 48 TDA8596 NXP Semiconductors I2C-bus controlled 4 × 45 W power amplifier with symmetrical inputs VP DIAG DB2 bit D7 POR IB1 bit D0 start enable twake STB SVR toff tamp_on fast mute amplifier output td(mute_off) td(soft_mute) td(fast_mute) 001aad168 Fig 3. Start-up and shut-down timing in I2C-bus mode TDA8596_2 Product data sheet © NXP B.V. 2007. All rights reserved. Rev. 02 — 8 November 2007 9 of 48 TDA8596 NXP Semiconductors I2C-bus controlled 4 × 45 W power amplifier with symmetrical inputs VP DIAG DB2 bit D7 POR IB1 bit D0 start enable twake STB SVR tload tamp_on toff fast mute amplifier output td(mute_off) td(soft_mute) td(fast_mute) 001aad169 Fig 4. Start-up and shut-down timing with DC load active in I2C-bus mode TDA8596_2 Product data sheet © NXP B.V. 2007. All rights reserved. Rev. 02 — 8 November 2007 10 of 48 TDA8596 NXP Semiconductors I2C-bus controlled 4 × 45 W power amplifier with symmetrical inputs VP DIAG DB2 bit D7 POR IB1 bit D0 start enable twake STB SVR tload tamp_on toff fast mute amplifier output td(mute_off) td(soft_mute) td(fast_mute) 001aad170 Fig 5. Start-up and shut-down timing with low pop and DC load activated TDA8596_2 Product data sheet © NXP B.V. 2007. All rights reserved. Rev. 02 — 8 November 2007 11 of 48 TDA8596 NXP Semiconductors I2C-bus controlled 4 × 45 W power amplifier with symmetrical inputs VP DIAG on STB mute standby SVR tamp_on toff soft mute fast mute amplifier output td(mute_off) td(soft_mute) td(mute_on) td(fast_mute) 001aad171 Fig 6. Start-up and shut-down timing in legacy mode 7.7 Power-on reset and supply voltage spikes If the supply voltage drops below 5 V in I2C-bus mode (see Figure 8 and 9), the content of the I2C-bus latches cannot be guaranteed and a power-on reset will be performed. This will cause all latches to be reset, the amplifier to be switched off and the DIAG pin to be pulled LOW, indicating that a power-on reset has occurred (see DB2[D7]). When bit IB1[D0] is set, the power-on flag is reset, the DIAG pin is released and the amplifier will start-up. In legacy mode a supply voltage drop below 5 V will switch off the amplifier without pulling the DIAG pin LOW. 7.8 Engine start and low voltage operation In steady state, the DC output voltage of an amplifier channel VO equals half the supply voltage (HVP). This voltage is related to the voltage on the SVR pin (refer to Figure 7: VO = VSVR − 1.4 V). An external capacitor has been connected to the SVR pin to suppress coupling of power supply ripple to the amplifier outputs. The headroom voltage Vhr is defined as the difference between the supply voltage VP and the DC output voltage VO, i.e. Vhr = VP − VO (refer to Figure 7). If the supply voltage drops, e.g. during an engine start, the outputs will follow slowly due to the capacitor on pin SVR. However, if the headroom voltage Vhr drops below the headroom protection threshold of 1.6 V, the headroom protection will be activated to prevent pop noise at the output. This protection will first activate the fast mute and will subsequently discharge the capacitor on pin SVR to generate more headroom for the amplifier (refer to Figure 8 and 9). TDA8596_2 Product data sheet © NXP B.V. 2007. All rights reserved. Rev. 02 — 8 November 2007 12 of 48 TDA8596 NXP Semiconductors I2C-bus controlled 4 × 45 W power amplifier with symmetrical inputs When the SVR capacitor has discharged, the amplifier will only start-up again when the supply voltage VP increases above the low VP mute threshold, typically 7.5 V. Below this threshold, the outputs of the amplifier remain low. In I2C-bus mode, a supply voltage drop below VP(reset), typically 5 V will result in setting bit DB2[D7]. In this condition the amplifier will wait for an I2C-bus command in order to start-up. The TDA8596 prevents internally induced output pops during engine start. In order to prevent pops on the output caused by the application (e.g. due to the tuner supply going out of regulation), the STB pin can be pulled LOW when an engine start is detected. The STB pin will activate the fast mute within 0.1 ms and consequently all disturbances at the amplifier inputs will be suppressed. V (V) 14 VP VSVR Vhr (1) 8.4 7 VO (2) 1.6 V headroom protection threshold (3) t (s) 001aad172 (1) Headroom voltage Vhr = VP − VO. (2) Steady state output voltage VO = VSVR − 1.4 V. (3) Headroom protection threshold = VO + 1.6 V. Fig 7. Low-headroom protection TDA8596_2 Product data sheet © NXP B.V. 2007. All rights reserved. Rev. 02 — 8 November 2007 13 of 48 TDA8596 NXP Semiconductors I2C-bus controlled 4 × 45 W power amplifier with symmetrical inputs VO (V) legacy and I2C-bus mode VP 14.4 output voltage (1) 8.8 Vhr 8.6 (3) (2) 7.2 VSVR 3.5 output voltage (3) t (s) t(start-Vo(off)) t(start-SVRoff) 001aad173 (1) Headroom protection activated: a) Fast mute. b) Discharge of SVR. (2) Low VP mute activated. (3) Low VP mute released. Fig 8. Low VP behavior; legacy and I2C-bus modes TDA8596_2 Product data sheet © NXP B.V. 2007. All rights reserved. Rev. 02 — 8 November 2007 14 of 48 TDA8596 NXP Semiconductors I2C-bus controlled 4 × 45 W power amplifier with symmetrical inputs VO (V) I2C-bus mode only VP 14.4 8.8 8.6 (1) 7.2 (2) 5.0 3.5 VSVR output voltage 0 POR IB1 bit D0 DIAG t (s) 001aad185 (1) Low VP mute activated. (2) VPOR: VP level at which POR is activated. Fig 9. Low VP behavior; I2C-bus mode only 7.9 Overvoltage and load dump protection When the supply voltage VP exceeds 22 V, all amplifier output stages will be switched to high-impedance. The TDA8596 is protected against load dump transients up to 50 V. 7.10 Thermal pre-warning and thermal protection If the average junction temperature reaches the (I2C-bus programmable) pre-warning level, a thermal pre-warning will be generated, which can be read out on the I2C-bus. If the TDA8596 is programmed to send thermal warning information to the DIAG pin, the DIAG pin will be pulled LOW. The default thermal pre-warning detection level (IB3[D4] = 0) is 145 °C typical. In case IB3[D4] = 1, the detection level is modified to 122 °C typical. In legacy mode the thermal pre-warning level is fixed at 145 °C typical. If the junction temperature increases further, the temperature controlled gain reduction will be activated for all four channels to reduce the output power (see Figure 10). If this still does not reduce the average junction temperature, all channels will be switched off at the absolute maximum temperature Toff, typical 175 °C. TDA8596_2 Product data sheet © NXP B.V. 2007. All rights reserved. Rev. 02 — 8 November 2007 15 of 48 TDA8596 NXP Semiconductors I2C-bus controlled 4 × 45 W power amplifier with symmetrical inputs 001aad174 30 Gv (dB) 20 10 0 145 155 165 175 Tj (°C) Fig 10. Temperature controlled amplifier gain 7.11 Diagnostics Diagnostic information can be read via the I2C-bus and it can also be made available on the DIAG pin or STB pin. The information on the DIAG pin is partly fixed, i.e. power-on reset occurred and low or high battery events. Through I2C-bus commands selectable information (i.e. load faults, temperature alarms and clip detection) can be made available. This information will be directed to the DIAG pin through a logical OR function. In case of any of the above mentioned failures, the DIAG pin will remain LOW so the microcontroller is triggered to read out the failure information via the I2C-bus (the DIAG pin can be used as microcontroller interrupt to minimize I2C-bus traffic). As soon as the failure is removed, the DIAG pin will be released. The STB pin can be configured as a second clip detection pin. The clip detection level is equal for all channels. It is possible to redirect the clip information of all separate channels to each of the two diagnostic pins DIAG or STB. This option can be used to distinguish between for instance clipping on the front and rear side channels (i.e. by redirecting the front channels to one diagnostic output and the rear channels to the second diagnostic output). Table 4 shows the diagnostic options for the DIAG pin and STB pin for both I2C-bus and legacy mode: Table 4. Diagnostic information per pin for various modes Diagnostic information I2C-bus mode Power-on reset no after power-on reset; pin DIAG will remain LOW until amplifier has been started no Low battery yes no yes Clip detection can be enabled per channel can be enabled per channel yes; fixed level for all channels on 2 % Pin DIAG Legacy mode Pin STB TDA8596_2 Product data sheet Pin DIAG © NXP B.V. 2007. All rights reserved. Rev. 02 — 8 November 2007 16 of 48 TDA8596 NXP Semiconductors I2C-bus controlled 4 × 45 W power amplifier with symmetrical inputs Table 4. Diagnostic information per pin for various modes …continued Diagnostic information I2C-bus mode Pin DIAG Pin STB Pin DIAG Temperature prewarning can be enabled no yes; pre-warning level is 145 °C Short can be enabled no yes Speaker protection (missing current) can be enabled no yes Offset detection no no no Load detection no no no Overvoltage yes no yes Legacy mode 7.12 Offset detection Offset detection can be performed either with or without input signal (for instance when the DSP is in mute after a start-up). Assume the amplifier is in I2C-bus mode. When an I2C-bus read of the output offset is performed the DBx[D2] latch will be set. When the amplifier BTL output voltage crosses the 1.55 V window threshold within 1 s after a read is performed, the DBx[D2] latch is reset and setting is disabled. After a certain delay, the next read can be performed. Example: in case the offset bits are still set when a successive read is performed more than 1 s after the previous read, the output signal has not been within the offset window thresholds for at least 1 s. This could either indicate an output signal with a frequency below 1 Hz or the presence of an output offset above 1.55 V (see Figure 11). I2C-bus mode only VO = VOUT+ − VOUT− offset threshold t reset: setting disabled t = 1 s: read = no offset DB1 bit D2 reset VO = VOUT+ − VOUT− offset threshold t read = set bit t = 1 s: read = offset DB1 bit D2 set 001aad175 Fig 11. Offset detection TDA8596_2 Product data sheet © NXP B.V. 2007. All rights reserved. Rev. 02 — 8 November 2007 17 of 48 TDA8596 NXP Semiconductors I2C-bus controlled 4 × 45 W power amplifier with symmetrical inputs 7.13 DC load detection When the DC load detection is enabled (IB1[D1] = 1), a DC offset is slowly applied at the outputs of the amplifiers during the start-up sequence (see Figure 4 and Figure 5) and the load currents as a result of the applied offset are measured. Based on this measurement the load impedance can be determined to differentiate between normal, line driver and no load (see Figure 12). NORMAL LOAD DETECTION LEVEL LINE DRIVER MODE 20 Ω 100 Ω 800 Ω OPEN-CIRCUIT 5 kΩ 001aad176 Fig 12. DC load detection levels When the amplifier is used in line driver mode and the external booster has an input impedance between 100 Ω and 800 Ω (DC-coupled), the DC load bits will be set at DBx[D5:D4] = 10 independent of the selected gain setting (see Table 5). Table 5. DC load detection translation table Load indication[1] DC load bits DBx[D5] DBx[D4] 0 0 normal load 1 0 line driver load 1 1 open load 0 1 not valid [1] Only when IB1[D2] = 0. By reading the I2C-bus bits the microprocessor can determine after the start-up of the amplifier whether a speaker or an external booster is connected and initiate the proper selection of the amplifier gain, i.e. 26 dB for normal mode or 16 dB for line driver mode. Gain selection will occur without audible pop noise when the amplifier is in mute. The DC load bit DBx[D4] is shared with the AC load detection. This implies that Table 5 is only valid when AC load detection is disabled (IB1[D2] = 0). When the AC load detection is enabled (IB1[D2] = 1) the bits DBx[D4] will show the result of the AC load detection. After disabling the AC load detection data bit DBx[D4] will show the result of the DC load measurement, which was stored during the AC load measurement. 7.14 AC load detection When AC load detection is enabled (IB1[D2] = 1), AC coupled speakers (e.g. tweeters) can be detected during the assembly process. The detection is performed by means of applying an audible input sine wave (e.g. 19 kHz) to the inputs of the amplifier. The AC current into the load is measured with a 460 mA peak current detector to detect the presence of an AC load. In order to prevent spurious AC load detection (e.g. due to amplifier on/off switching), the AC load detection bit will only be set when the peak current threshold is triggered at least three times. Besides the 460 mA peak current threshold, a secondary threshold level at 230 mA is present. In case this level is not triggered, a high ohmic DC load (e.g. line driver) is assumed (also refer to Figure 13). TDA8596_2 Product data sheet © NXP B.V. 2007. All rights reserved. Rev. 02 — 8 November 2007 18 of 48 TDA8596 NXP Semiconductors I2C-bus controlled 4 × 45 W power amplifier with symmetrical inputs Example: at an AC output voltage of 2 V peak the total impedance must be less than 4 Ω to detect an AC coupled load or above 9 Ω to guarantee the detection of a DC load. Refer to Table 6 for the interpretation AC load detection bits. Table 6. AC load detection translation table Normal DC load bit DBx[D5] Line driver DC load bit DBx[D4] Load indication Don’t care 0 no AC load detected Don’t care 1 AC load detected The AC load detection can only be performed when the amplifier has completed its start-up sequence. Consequently it will not conflict with the DC load detection. 001aad177 20 |Zth(load)| (Ω) 16 (1) 12 8 (2) 4 0 0 1 2 3 4 5 VoM (V) (1) IoM < 230 mA (no load detection level). (2) IoM > 460 mA (load detection level). Fig 13. AC load impedance versus output signal 7.15 I2C-bus diagnostic bits read out The diagnostic information of the amplifier can be read out via the I2C-bus. The I2C-bus data bits are set in case a failure event occurs and are not reset until an I2C-bus read command is given. This implies that even when the failure mode is removed before reading out the I2C-bus, the microcontroller will still be able to read out what kind of failure has occurred. A consequence of this procedure is that during the I2C-bus read cycle old information is read. When actual information is required, it is recommended to perform two successive read actions. The DIAG pin will give actual diagnostic information (when selected), however it does not distinguish between the various failure modes. The DIAG pin can be used to trigger an I2C-bus read out of the data bits to retrieve actual diagnostic information. When a failure is no longer present, the DIAG pin will be released instantly, independently of the I2C-bus latches. TDA8596_2 Product data sheet © NXP B.V. 2007. All rights reserved. Rev. 02 — 8 November 2007 19 of 48 TDA8596 NXP Semiconductors I2C-bus controlled 4 × 45 W power amplifier with symmetrical inputs 8. I2C-bus specification Table 7. TDA8596 ADDRESS with hardware address select Pin ADSEL A6 A5 A4 A3 A2 A1 A0 R/W Open 1 1 0 1 1 0 0 0 = write to TDA8596 1 = read from TDA8596 51 kΩ to ground 1 1 0 1 1 0 1 0 = write to TDA8596 1 = read from TDA8596 10 kΩ to ground 1 1 0 1 1 1 1 0 = write to TDA8596 1 = read from TDA8596 Ground no I2C-bus; legacy mode SDA SDA SCL SCL S P START condition STOP condition mba608 Fig 14. START and STOP conditions SDA SCL data line stable; data valid change of data allowed mba607 Fig 15. Bit transfer TDA8596_2 Product data sheet © NXP B.V. 2007. All rights reserved. Rev. 02 — 8 November 2007 20 of 48 TDA8596 NXP Semiconductors I2C-bus controlled 4 × 45 W power amplifier with symmetrical inputs I2C-BUS WRITE SCL 1 SDA MSB 2 7 MSB − 1 S 8 LSB + 1 9 ACK ADDRESS 1 MSB 2 MSB − 1 A W 7 LSB + 1 8 LSB 9 ACK A WRITE DATA P To stop the transfer, after the last acknowledge (A) a STOP condition (P) must be generated I2C-BUS READ SCL 1 SDA MSB 2 7 MSB − 1 S 8 LSB + 1 9 ACK R ADDRESS 1 MSB 2 7 MSB − 1 A LSB + 1 READ DATA : generated by slave : START P : STOP A : acknowledge NA : not acknowledge R/W : read / write LSB 9 ACK NA P To stop the transfer, the last byte must not be acknowledged and a STOP condition (P) must be generated : generated by master (microcontroller) S 8 001aac649 Fig 16. I2C-bus read and write modes 8.1 Instruction bytes I2C-bus mode: • If R/W bit = 0, the TDA8596 expects 3 instruction bytes: IB1, IB2 and IB3 • After a power-on reset, all instruction bits are set to logic 0 Legacy mode: • The settings are equal to the condition with all instruction bits set to logic 0 (see Table 8), with the exception of IB1[D0] bit that is ignored in legacy mode. Table 8. Instruction byte IB1 Bit Description D7 don’t care D6 channel 3 clip information on DIAG or STB pin 0 = clip information on DIAG pin 1 = clip information on STB pin D5 channel 1 clip information on DIAG or STB pin 0 = clip information on DIAG pin 1 = clip information on STB pin TDA8596_2 Product data sheet © NXP B.V. 2007. All rights reserved. Rev. 02 — 8 November 2007 21 of 48 TDA8596 NXP Semiconductors I2C-bus controlled 4 × 45 W power amplifier with symmetrical inputs Table 8. Instruction byte IB1 …continued Bit Description D4 channel 4 clip information on DIAG or STB pin 0 = clip information on DIAG pin 1 = clip information on STB pin D3 channel 2 clip information on DIAG or STB pin 0 = clip information on DIAG pin 1 = clip information on STB pin D2 AC load detection enable 0 = AC load detection disabled 1 = AC load detection enabled; DBx[D4] bits not available for DC load detection D1 DC load detection enable 0 = DC load detection disabled 1 = DC load will be detected D0 amplifier start enable; (clear power-on reset flag, DB2[D7]) 0 = amplifier not enabled, DIAG pin will remain LOW 1 = amplifier will start-up, power-on occurred (DB2[D7]) will be reset and DIAG pin will be released Table 9. Instruction byte IB2 Bit Description D7 and D6 clip detection level 00 = clip detection level 2 % 01 = clip detection level 5 % 10 = clip detection level 10 % 11 = clip detection level disabled D5 temperature information on DIAG pin 0 = temperature information on DIAG pin 1 = no temperature information on DIAG pin D4 load fault information (shorts, missing current) on DIAG pin 0 = fault information on DIAG pin 1 = no fault information on DIAG pin D3 low pop (slow start) enable 0 = low pop enabled 1 = low pop disabled D2 soft mute channel 1 and channel 3 (mute delay 20 ms) 0 = no mute 1 = mute D1 soft mute channel 2 and channel 4 (mute delay 20 ms) 0 = no mute 1 = mute TDA8596_2 Product data sheet © NXP B.V. 2007. All rights reserved. Rev. 02 — 8 November 2007 22 of 48 TDA8596 NXP Semiconductors I2C-bus controlled 4 × 45 W power amplifier with symmetrical inputs Table 9. Instruction byte IB2 …continued Bit Description D0 fast mute all amplifier channels (mute delay 100 µs) 0 = no mute 1 = mute Table 10. Instruction byte IB3 Bit Description D7 don’t care D6 amplifier channel 1 and channel 3 gain select 0 = 26 dB 1 = 16 dB D5 amplifier channel 2 and channel 4 gain select 0 = 26 dB 1 = 16 dB D4 temperature pre-warning level 0 = warning level on 145 °C 1 = warning level on 122 °C D3 disable channel 3 0 = channel 3 enabled 1 = channel 3 disabled D2 disable channel 1 0 = channel 1 enabled 1 = channel 1 disabled D1 disable channel 4 0 = channel 4 enabled 1 = channel 4 disabled D0 disable channel 2 0 = channel 2 enabled 1 = channel 2 disabled 8.2 Data bytes I2C-bus mode: • If R/W = 1, the TDA8596 will send four data bytes to the microprocessor: DB1, DB2, DB3, and DB4 • All bits are latched • All bits are reset after a read operation except D4 and D5. D2 is set after a read operation, refer to the offset detection described in Section 7.12 • For explanation of AC and DC load detection bits, refer to Section 7.13 and Section 7.14 TDA8596_2 Product data sheet © NXP B.V. 2007. All rights reserved. Rev. 02 — 8 November 2007 23 of 48 TDA8596 NXP Semiconductors I2C-bus controlled 4 × 45 W power amplifier with symmetrical inputs Table 11. Data byte DB1 Bit Description D7 temperature pre-warning 0 = no warning 1 = junction temperature too high D6 speaker fault channel 2 (missing current) 0 = no missing current 1 = missing current D5 and D4 channel 2 DC load or AC load detection if bit IB1[D2] = 1, AC load detection is enabled, bit D5 and bit D4 are available for AC load detection 00 = no AC load 01 = AC load detected 10 = no AC load 11 = AC load detected if bit IB1[D2] = 0, DC load detection is enabled, bits D5 and bit D4 are available for DC load detection 00 = normal load 01 = not valid 10 = line driver load 11 = open load D3 channel 2 shorted load 0 = not shorted load 1 = shorted load D2 channel 2 output offset 0 = no output offset 1 = output offset D1 channel 2 short to VP 0 = no short to VP 1 = short to VP D0 channel 2 short to ground 0 = no short to ground 1 = short to ground Table 12. Data byte DB2 Bit Description D7 power-on reset occurred/amplifier status 0 = amplifier on 1 = power-on reset has occurred; amplifier off D6 speaker fault channel 4 (missing current) 0 = no missing current 1 = missing current TDA8596_2 Product data sheet © NXP B.V. 2007. All rights reserved. Rev. 02 — 8 November 2007 24 of 48 TDA8596 NXP Semiconductors I2C-bus controlled 4 × 45 W power amplifier with symmetrical inputs Table 12. Data byte DB2 …continued Bit Description D5 and D4 channel 4 DC load or AC load detection if bit IB1[D2] = 1, AC load detection is enabled, bit D5 and bit D4 are available for AC load detection 00 = no AC load 01 = AC load detected 10 = no AC load 11 = AC load detected if bit IB1[D2] = 0, DC load detection is enabled, bits D5 and bit D4 are available for DC load detection 00 = normal load 01 = not valid 10 = line driver load 11 = open load D3 channel 4 shorted load 0 = not shorted load 1 = shorted load D2 channel 4 output offset 0 = no output offset 1 = output offset D1 channel 4 short to VP 0 = no short to VP 1 = short to VP D0 channel 4 short to ground 0 = no short to ground 1 = short to ground Table 13. Data byte DB3 Bit Description D7 maximum temperature protection 0 = no protection 1 = maximum temperature protection D6 speaker fault channel 1 (missing current) 0 = no missing current 1 = missing current TDA8596_2 Product data sheet © NXP B.V. 2007. All rights reserved. Rev. 02 — 8 November 2007 25 of 48 TDA8596 NXP Semiconductors I2C-bus controlled 4 × 45 W power amplifier with symmetrical inputs Table 13. Data byte DB3 …continued Bit Description D5 and D4 channel 1 DC load or AC load detection if bit IB1[D2] = 1, AC load detection is enabled, bit D5 and bit D4 are available for AC load detection 00 = no AC load 01 = AC load detected 10 = no AC load 11 = AC load detected if bit IB1[D2] = 0, DC load detection is enabled, bits D5 and bit D4 are available for DC load detection 00 = normal load 01 = not valid 10 = line driver load 11 = open load D3 channel 1 shorted load 0 = not shorted load 1 = shorted load D2 channel 1 output offset 0 = no output offset 1 = output offset D1 channel 1 short to VP 0 = no short to VP 1 = short to VP D0 channel 1 short to ground 0 = no short to ground 1 = short to ground Table 14. Data byte DB4 Bit Description D7 reserved D6 speaker fault channel 3 (missing current) 0 = no missing current 1 = missing current TDA8596_2 Product data sheet © NXP B.V. 2007. All rights reserved. Rev. 02 — 8 November 2007 26 of 48 TDA8596 NXP Semiconductors I2C-bus controlled 4 × 45 W power amplifier with symmetrical inputs Table 14. Data byte DB4 …continued Bit Description D5 and D4 channel 3 DC load or AC load detection if bit IB1[D2] = 1, AC load detection is enabled, bit D5 and bit D4 are available for AC load detection 00 = no AC load 01 = AC load detected 10 = no AC load 11 = AC load detected if bit IB1[D2] = 0, DC load detection is enabled, bits D5 and bit D4 are available for DC load detection 00 = normal load 01 = not valid 10 = line driver load 11 = open load D3 channel 3 shorted load 0 = not shorted load 1 = shorted load D2 channel 3 output offset 0 = no output offset 1 = output offset D1 channel 3 short to VP 0 = no short to VP 1 = short to VP D0 channel 3 short to ground 0 = no short to ground 1 = short to ground 9. Limiting values Table 15. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Symbol Parameter Conditions Min Max Unit VP supply voltage operating - 18 V non operating −1 +50 V load dump protection; duration 50 ms; rise time > 2.5 ms - 50 V 10 minutes maximum - −2 V - 13 A - 8 A VP(r) reverse supply voltage IOSM non-repetitive peak output current IORM repetitive peak output current Tj junction temperature - 150 °C Tstg storage temperature −55 +150 °C repetitive TDA8596_2 Product data sheet © NXP B.V. 2007. All rights reserved. Rev. 02 — 8 November 2007 27 of 48 TDA8596 NXP Semiconductors I2C-bus controlled 4 × 45 W power amplifier with symmetrical inputs Table 15. Limiting values …continued In accordance with the Absolute Maximum Rating System (IEC 60134). Symbol Parameter Tamb ambient temperature V(prot) protection voltage Vx voltage on pin x Conditions AC and DC short circuit voltage of output pins and across the load SCL and SDA inputs, SVR and DIAG [1] STB Min Max Unit −40 +105 °C - VP V 0 6.5 V 0 13 V 0 24 V Ptot total power dissipation Tcase = 70 °C - 80 W Vesd electrostatic discharge voltage human body model; C = 100 pF; Rs = 1.5 kΩ - 2000 V machine model; C = 200 pF; Rs = 10 Ω; L = 0.75 µH - 200 V [1] 10 kΩ series resistance if connected to VP. 10. Thermal characteristics Table 16. Thermal characteristics Symbol Parameter Rth(j-c) Rth(j-a) Conditions Typ Unit thermal resistance from junction to case 1 K/W thermal resistance from junction to ambient 35 K/W 11. Characteristics Table 17. Characteristics Refer to test circuit (see Figure 29) at VP = 14.4 V; RL = 4 Ω; f = 1 kHz; RS = 0 Ω; normal mode; unless otherwise specified. Tested at Tamb = 25 °C; guaranteed for Tamb = −40 °C to +105 °C. Symbol Parameter Conditions Min Typ Max Unit 8 14.4 18 V 8 14.4 16 V Supply voltage behavior VP supply voltage RL = 4 Ω RL = 2 Ω [1] Iq quiescent current no load - 270 400 mA Istb standby current VSTB = 0.4 V - 4 15 µA VO output voltage 6.7 7 7.2 V VP(low)(mute) low supply voltage mute with rising supply voltage 6.9 7.5 8 V with falling supply voltage 6.3 6.8 7.4 V ∆VP(low)(mute) low supply voltage mute hysteresis 0.1 0.7 1 V Vth(ovp) overvoltage protection threshold voltage 18 20 22 V Vhr headroom voltage 1.1 1.6 2.0 V when headroom protection is activated; see Figure 7 TDA8596_2 Product data sheet © NXP B.V. 2007. All rights reserved. Rev. 02 — 8 November 2007 28 of 48 TDA8596 NXP Semiconductors I2C-bus controlled 4 × 45 W power amplifier with symmetrical inputs Table 17. Characteristics …continued Refer to test circuit (see Figure 29) at VP = 14.4 V; RL = 4 Ω; f = 1 kHz; RS = 0 Ω; normal mode; unless otherwise specified. Tested at Tamb = 25 °C; guaranteed for Tamb = −40 °C to +105 °C. Symbol Parameter Conditions Min Typ Max Unit VPOR power-on reset voltage see Figure 9 4.1 5.0 5.8 V VO(offset) output offset voltage amplifier on −95 0 +95 mV amplifier mute −25 0 +25 mV line driver mode −40 0 +40 mV - - 1 V - - 1 V 2.5 - 4.5 V 2.5 - VP V 6.5 - VP V ISTB = 150 µA 5.6 - 6.1 V ISTB = 500 µA 6.1 - 7.4 V clip detection not active; I2C-bus mode - 4 30 µA legacy mode - 10 70 µA - 300 500 µs - - 10 µA Mode select pin STB/second clip detection pin VSTB voltage on pin STB Standby mode I2C-bus mode legacy mode (I2C-bus off) Mute operating mode legacy mode (I2C-bus off) Operating mode I2C-bus mode legacy mode (I2C-bus off) LOW voltage on pin STB when pulled down during clipping ISTB current on pin STB [2] 0 V < VSTB < 8.5 V Start-up, shut-down and mute timing twake wake-up time ILO(SVR) output leakage current on pin SVR time after wake-up via STB pin before first I2C-bus transmission is recognized; see Figure 3 TDA8596_2 Product data sheet © NXP B.V. 2007. All rights reserved. Rev. 02 — 8 November 2007 29 of 48 TDA8596 NXP Semiconductors I2C-bus controlled 4 × 45 W power amplifier with symmetrical inputs Table 17. Characteristics …continued Refer to test circuit (see Figure 29) at VP = 14.4 V; RL = 4 Ω; f = 1 kHz; RS = 0 Ω; normal mode; unless otherwise specified. Tested at Tamb = 25 °C; guaranteed for Tamb = −40 °C to +105 °C. Symbol Parameter Conditions td(mute_off) mute off delay time mute to 10 % of output signal; ILO(SVR) = 0 µA tamp_on toff amplifier on time amplifier switch-off time Min Typ Max Unit I2C-bus mode (IB1[D0]); with ILO(SVR) = 10 µA → +15 ms; no DC load (IB1[D1] = 0); low pop disabled (IB2[D3] = 1); see Figure 3 [3] 295 465 795 ms I2C-bus mode (IB1[D0]); with ILO(SVR) = 10 µA → +20 ms; DC load active (IB1[D1] = 1); low pop disabled (IB2[D3] = 1); see Figure 4 [3] 500 640 940 ms I2C-bus mode (IB1[D0]); with ILO(SVR) = 10 µA → +20 ms; DC load active (IB1[D1] = 0); low pop enabled (IB2[D3] = 0); see Figure 5 [3] 640 830 1190 ms legacy mode; with ILO(SVR) = 10 µA → +20 ms; VSTB = 7 V; RADSEL = 0 Ω; see Figure 6 [3] 430 650 1030 ms I2C-bus mode (IB1[D0]); with ILO(SVR) = 10 µA → +30 ms; no DC load (IB1[D1] = 0); low pop disabled (IB2[D3] = 1); see Figure 3 [3] 360 520 870 ms I2C-bus mode (IB1[D0]); with ILO(SVR) = 10 µA → +35 ms; DC load active (IB1[D1] = 1); low pop disabled (IB2[D3] = 1); see Figure 4 [3] 565 695 1015 ms I2C-bus mode (IB1[D0]); with ILO(SVR) = 10 µA → +30 ms; DC load active (IB1[D1] = 0); low pop enabled (IB2[D3] = 0); see Figure 5 [3] 710 890 1270 ms legacy mode; with ILO(SVR) = 10 µA → +20 ms; VSTB = 7 V; RADSEL = 0 Ω; see Figure 6 [3] 510 720 1120 ms with ILO(SVR) = 10 µA → +0 ms; low pop enabled (IB2[D3] = 0); see Figure 4 [3] 120 245 530 ms with ILO(SVR) = 10 µA → +0 ms; low pop disabled (IB2[D3] = 1); see Figure 5 [3] 140 280 620 ms amplifier from mute to 90 % of output signal; ILO(SVR) = 0 µA time to DC output voltage < 0.1 V; I2C-bus mode (IB1[D0]); ILO(SVR) = 0 µA td(mute-on) mute to on delay time from 10 % to 90 % of output signal; IB2[D1] = 1 to 0; Vi = 50 mV; see Figure 6 - 20 40 ms td(soft_mute) soft mute delay time from 10 % to 90 % of output signal; IB2[D1] = 0 to 1; Vi = 50 mV; see Figure 6 - 20 40 ms TDA8596_2 Product data sheet © NXP B.V. 2007. All rights reserved. Rev. 02 — 8 November 2007 30 of 48 TDA8596 NXP Semiconductors I2C-bus controlled 4 × 45 W power amplifier with symmetrical inputs Table 17. Characteristics …continued Refer to test circuit (see Figure 29) at VP = 14.4 V; RL = 4 Ω; f = 1 kHz; RS = 0 Ω; normal mode; unless otherwise specified. Tested at Tamb = 25 °C; guaranteed for Tamb = −40 °C to +105 °C. Symbol Parameter Conditions Min Typ Max Unit td(fast_mute) fast mute delay time from 10 % to 90 % of output signal; VSTB from 8 V to 1.3 V; Vi = 50 mV; see Figure 6 - 0.1 1 ms t(start-Vo(off)) engine start to output off time VP from 14.4 V to 7 V; Vo < 0.5 V; see Figure 8 - 0.1 1 ms t(start-SVRoff) engine start to SVR off time VP from 14.4 V to 7 V; VSVR < 2 V; see Figure 8 - 40 75 ms I2C-bus interface[4] VIL LOW-level input voltage pins SCL and SDA - - 1.5 V VIH HIGH-level input voltage pins SCL and SDA 2.3 - 5.5 V VOL LOW-level output voltage pin SDA; IL = 5 mA - - 0.4 V fSCL SCL clock frequency - 400 - kHz RADSEL resistance on pin ADSEL I2C-bus address A[6:0] = 110 1100 155 - - kΩ I2C-bus address A[6:0] = 110 1101 42 51 57 kΩ I2C-bus address A[6:0] = 110 1111 7 10 15 kΩ - - 0.5 kΩ 26 dB gain; normal mode - - 5 kΩ 16 dB gain; line driver mode 20 - - kΩ - - 0.3 V ±1.3 ±1.55 ± 2.0 V legacy mode Gain select pin RGAINSEL resistance on pin GAINSEL legacy mode (I2C-bus off) Diagnostic VOL(DIAG) LOW-level output voltage on pin DIAG VO(offset_det) output voltage at offset detection THDclip total harmonic distortion clip detection level ∆THDclip Tj(AV)(pwarn) Tj(AV)(G(−0.5dB)) fault condition; IDIAG = 1 mA VP > 10 V IB2[D7:D6] = 10; level 10 % 5 10 16 % IB2[D7:D6] = 01; level 5 % 3 5 7 % IB2[D7:D6] = 00; level 2 % 1 2 3 % total harmonic distortion clip detection level variation between IB2[D7:D6] = 10 and IB2[D7:D6] = 01 (level between 10 % and 5 %) 1 4 8 % between IB2[D7:D6] = 01 and IB2[D7:D6] = 00 (level between 5 % and 2 %) 1 3.5 6 % pre-warning average junction temperature IB3[D4] = 0 135 145 155 °C IB3[D4] = 1 112 122 132 °C average junction Vi = 0.05 V temperature for 0.5 dB gain reduction 150 155 160 °C TDA8596_2 Product data sheet © NXP B.V. 2007. All rights reserved. Rev. 02 — 8 November 2007 31 of 48 TDA8596 NXP Semiconductors I2C-bus controlled 4 × 45 W power amplifier with symmetrical inputs Table 17. Characteristics …continued Refer to test circuit (see Figure 29) at VP = 14.4 V; RL = 4 Ω; f = 1 kHz; RS = 0 Ω; normal mode; unless otherwise specified. Tested at Tamb = 25 °C; guaranteed for Tamb = −40 °C to +105 °C. Symbol Parameter Conditions Min Typ Max Unit ∆Tj(pw-G(−0.5dB)) prewarning to 0.5 dB gain reduction junction temperature difference 7 10 13 °C ∆Tj(G(−0.5dB)-of) junction temperature difference between 0.5 dB gain reduction and off 10 15 20 °C ∆G(th_fold) gain reduction of thermal foldback - 20 - dB Zth(load) load detection threshold impedance I2C-bus mode normal load detection - - 20 Ω line driver load detection 100 - 800 Ω Zth(open) open load detection threshold impedance I2C-bus 5000 - - Ω Ith(o)det(load)AC AC load detection output threshold current I2C-bus mode AC load bit is set 460 - - mA AC load bit is not set - - 230 mA output power RL = 4 Ω; VP = 14.4 V; THD = 0.5 % 18 20 - W RL = 4 Ω; VP = 14.4 V; THD = 10 % 23 25 - W RL = 4 Ω; VP = 14.4 V; maximum power; Vi = 2 V (RMS) square wave 37 40 - W RL = 4 Ω; VP = 15.2 V; maximum power; Vi = 2 V (RMS) square wave 41 45 - W mode Amplifier Po THD αcs total harmonic distortion channel separation RL = 2 Ω; VP = 14.4 V; THD = 0.5 % 29 32 - W RL = 2 Ω; VP = 14.4 V; THD = 10 % 37 41 - W RL = 2 Ω; VP = 14.4 V; maximum power; Vi = 2 V (RMS) square wave 58 64 - W Po = 1 W to 12 W; f = 1 kHz; RL = 4 Ω - 0.01 0.1 % Po = 1 W to 12 W; f = 10 kHz - 0.09 0.3 % Po = 1 W to 12 W; f = 20 kHz - 0.14 0.4 % line driver mode; Vo = 1 V (RMS) and 5 V (RMS); f = 20 Hz to 20 kHz - 0.02 0.05 % f = 1 kHz; RS = 1 kΩ 65 80 - dB f = 10 kHz; RS = 1 kΩ 60 65 - dB PSRR power supply rejection f = 100 Hz to 10 kHz; RS = 1 kΩ ratio 55 70 - dB CMRR common mode rejection ratio normal mode; Vcm = 0.3 V (p-p); f = 1 kHz to 3 kHz; RS = 1 kΩ 45 65 - dB Vcm(max)(rms) maximum common mode voltage (RMS value) f = 1 kHz - - 0.6 V TDA8596_2 Product data sheet © NXP B.V. 2007. All rights reserved. Rev. 02 — 8 November 2007 32 of 48 TDA8596 NXP Semiconductors I2C-bus controlled 4 × 45 W power amplifier with symmetrical inputs Table 17. Characteristics …continued Refer to test circuit (see Figure 29) at VP = 14.4 V; RL = 4 Ω; f = 1 kHz; RS = 0 Ω; normal mode; unless otherwise specified. Tested at Tamb = 25 °C; guaranteed for Tamb = −40 °C to +105 °C. Symbol Parameter Conditions Vn(o) noise output voltage filter 20 Hz to 22 kHz; RS = 1 kΩ voltage gain Gv Min Typ Max Unit mute mode - 19 26 µV line driver mode - 22 29 µV normal mode; Tamb = 25 °C to 105 °C - 45 65 µV normal mode; Tamb = −20 °C to 25 °C - 45 110 µV 25.5 26 26.5 dB 15.5 16 16.5 dB 44 60 100 kΩ differential in; differential out normal mode line driver mode [5] Ri input resistance symmetrical input; Ci = 470 nF; see Figure 29 αmute mute attenuation Vo / Vo(mute); Vi = 50 mV 80 92 - dB Vo(mute)(RMS) RMS mute output voltage Vi = 1 V (RMS); filter 20 Hz to 22 kHz - 25 - µV Bp power bandwidth −1 dB - 20 to 20000 - Hz [1] Operation above 16 V with a 2 Ω reactive load can trigger the amplifier protection. The amplifier switches off and will restart after 16 ms resulting in an ‘audio hole’. [2] VSTB depends on the current into the STB pin: minimum = (1429 × ISTB) + 5.4 V, maximum = (3143 × ISTB) + 5.6 V. [3] The times are specified without a leakage current. For a leakage current of 10 µA on the SVR pin, the delta time is specified. If the capacitor value on the SVR pin changes with ±30 %, the specified time will also change with ±30 %. The specified time includes an ESR of the capacitor on the SVR pin of up to 15 Ω. [4] Standard I2C-bus spec: maximum LOW level = 0.3 × VDD, minimum HIGH-level = 0.7 × VDD. To comply with 5 V and 3.3 V logic the maximum LOW level is defined with VDD = 5 V and the minimum HIGH-level with VDD = 3.3 V. [5] Ri is the total differential input resistance. f−3dB cut-off frequency is defined as 1 1 ------------------------------------- = ------------------------------------------------------------------- = 19 Hz assuming worst-case low input resistance and 20 % spread in Ci. 2π × R i × C i ⁄ 2 2π × 44 kΩ × 235 nF × 0.8 TDA8596_2 Product data sheet © NXP B.V. 2007. All rights reserved. Rev. 02 — 8 November 2007 33 of 48 TDA8596 NXP Semiconductors I2C-bus controlled 4 × 45 W power amplifier with symmetrical inputs 12. Performance diagrams 001aad139 102 THD (%) 10 1 10−1 (1) 10−2 (2) (3) 10−3 10−2 10−1 1 102 10 Po (W) VP = 14.4 V. (1) f = 10 kHz. (2) f = 1 kHz. (3) f = 100 Hz. Fig 17. Total harmonic distortion as a function of output power; 4 Ω load 001aad140 102 THD (%) 10 1 (1) 10−1 (2) (3) 10−2 10−3 10−2 10−1 1 102 10 Po (W) VP = 14.4 V. (1) f = 10 kHz. (2) f = 1 kHz. (3) f = 100 Hz. Fig 18. Total harmonic distortion as a function of output power; 2 Ω load TDA8596_2 Product data sheet © NXP B.V. 2007. All rights reserved. Rev. 02 — 8 November 2007 34 of 48 TDA8596 NXP Semiconductors I2C-bus controlled 4 × 45 W power amplifier with symmetrical inputs 001aad141 28 (1) Po (W) 26 24 22 (2) 20 18 10−2 10−1 1 102 10 f (kHz) VP = 14.4 V. (1) THD = 10 %. (2) THD = 0.5 %. Fig 19. Output power as a function of frequency; 4 Ω load 001aad142 55 Po (W) 45 (1) 35 25 10−2 (2) 10−1 1 102 10 f (kHz) VP = 14.4 V. (1) THD = 10 %. (2) THD = 0.5 %. Fig 20. Output power as a function of frequency; 2 Ω load TDA8596_2 Product data sheet © NXP B.V. 2007. All rights reserved. Rev. 02 — 8 November 2007 35 of 48 TDA8596 NXP Semiconductors I2C-bus controlled 4 × 45 W power amplifier with symmetrical inputs 001aad143 60 Po (W) (1) 40 (2) (3) 20 0 5 10 15 20 VP (V) f = 1 kHz. (1) Po(max). (2) THD = 10 %. (3) THD = 0.5 %. Fig 21. Output power as a function of supply voltage; 4 Ω load 001aad144 100 Po (W) 80 (1) 60 (2) 40 (3) 20 0 5 10 15 20 VP (V) f = 1 kHz. (1) Po(max). (2) THD = 10 %. (3) THD = 0.5 %. Fig 22. Output power as a function of supply voltage; 2 Ω load TDA8596_2 Product data sheet © NXP B.V. 2007. All rights reserved. Rev. 02 — 8 November 2007 36 of 48 TDA8596 NXP Semiconductors I2C-bus controlled 4 × 45 W power amplifier with symmetrical inputs 001aad145 1 THD (%) 10−1 10−2 (1) (2) 10−3 10−2 10−1 1 102 10 f (kHz) VP = 14.4 V; RL = 4 Ω. (1) Po = 1 W. (2) Po = 10 W. Fig 23. Total harmonic distortion as a function of frequency; normal mode 001aag000 10−1 THD (%) (1) 10−2 (2) (3) 10−3 10−2 10−1 1 102 10 f (kHz) VP = 14.4 V; RL = 600 Ω. (1) Vo = 5 V; front channel. (2) Vo = 1 V. (3) Vo = 5 V; rear channel. Fig 24. Total harmonic distortion as a function of frequency; line driver mode TDA8596_2 Product data sheet © NXP B.V. 2007. All rights reserved. Rev. 02 — 8 November 2007 37 of 48 TDA8596 NXP Semiconductors I2C-bus controlled 4 × 45 W power amplifier with symmetrical inputs 001aag001 −40 PSRR (dB) −50 (1) −60 −70 (2) −80 −90 10 102 103 104 105 f (Hz) VP = 14.4 V; RL = 4 Ω; Vripple = 2 V (p-p). (1) front channel. (2) rear channel. Fig 25. Powers supply ripple rejection ratio as a function of frequency 001aag002 −50 αcs (dB) −60 −70 −80 −90 −100 10 102 103 104 105 f (Hz) VP = 14.4 V; RL = 4 Ω; Po = 4 W. Fig 26. Channel separation as a function of frequency TDA8596_2 Product data sheet © NXP B.V. 2007. All rights reserved. Rev. 02 — 8 November 2007 38 of 48 TDA8596 NXP Semiconductors I2C-bus controlled 4 × 45 W power amplifier with symmetrical inputs 001aag003 50 Ptot (W) 40 30 20 10 0 0 10 20 30 40 Po (W) VP = 14.4 V; RL = 4 Ω; f = 1 kHz. Fig 27. Power dissipation as a function of output power; 4 Ω load 001aag004 100 Ptot (W) 80 60 40 20 0 0 20 40 60 80 Po (W) VP = 14.4 V; RL = 2 Ω; f = 1 kHz. Fig 28. Power dissipation as a function of output power; 2 Ω load TDA8596_2 Product data sheet © NXP B.V. 2007. All rights reserved. Rev. 02 — 8 November 2007 39 of 48 TDA8596 NXP Semiconductors I2C-bus controlled 4 × 45 W power amplifier with symmetrical inputs 13. Application information RADSEL(2) +8.5 V SDA ADSEL SCL VP1 VP2 +5 V 28 26 21 19, 20 34, 35 10 kΩ 10 kΩ 33 DIAG STB 29 IN3+ 13 Ci Rs / 2 Vi / 2 STANDBY/ FAST MUTE SELECT DIAGNOSTIC/ CLIP DETECT I2C-BUS Ri/2 470 nF Vi / 2 Rs / 2 Ci Rs / 2 470 nF Ci IN3− IN1+ Vi / 2 14 7 MUTE Ri/2 Rs / 2 Ci Rs / 2 470 nF Ci IN1− IN4+ Vi / 2 6 11 PROTECTION/ DIAGNOSTIC MUTE Ri/2 Vi / 2 Ci Rs / 2 470 nF Ci IN4− IN2+ Vi / 2 12 9 Vcm Ci Rs / 2 IN2− 8 2 OUT1− PROTECTION/ DIAGNOSTIC Ri/2 MUTE Ri/2 (1) 25 OUT4+ 26 dB/ 16 dB 23 OUT4− PROTECTION/ DIAGNOSTIC Ri/2 470 nF Vi / 2 (1) 4 OUT1+ 26 dB/ 16 dB 470 nF Rs / 2 17 OUT3− Ri/2 470 nF Vi / 2 (1) 18 OUT3+ 26 dB/ 16 dB MUTE Ri/2 (1) 30 OUT2+ 26 dB/ 16 dB 32 OUT2− PROTECTION/ DIAGNOSTIC 470 nF VP 36 TAB TDA8596 22 µF 27 10 22 3 31 16 24 SVR SGND GAINSEL PGND1 PGND2 PGND3 PGND4 (2) 001aag005 (1) A capacitor of 10 nF may be added between every amplifier output and ground for EMC reasons. (2) The SVR capacitor and RADSEL resistor should first be connected to SGND before connecting to PGND. Fig 29. Test and application information TDA8596_2 Product data sheet © NXP B.V. 2007. All rights reserved. Rev. 02 — 8 November 2007 40 of 48 TDA8596 NXP Semiconductors I2C-bus controlled 4 × 45 W power amplifier with symmetrical inputs 8.5 V 5.6 kΩ 4.7 kΩ TDA8596 29 18 kΩ 3.3 V MICROCONTROLLER STB switch 10 kΩ 001aag009 Fig 30. Circuit for combined STB and clip detection function on pin STB TDA8596_2 Product data sheet © NXP B.V. 2007. All rights reserved. Rev. 02 — 8 November 2007 41 of 48 TDA8596 NXP Semiconductors I2C-bus controlled 4 × 45 W power amplifier with symmetrical inputs 13.1 PCB schematic and layout VP2 19, 20 IN1+ 7 34, 35 470 nF IN1− PGND4 VP1 470 nF PGND1 VP TAB/GND 220 nF PGND3 220 nF PGND2 2200 µF/ 16 V 3 31 16 24 36 n.c. 1 5 6 15 470 nF 470 nF IN2+ IN2− SGND 470 nF IN3+ IN3− 4 8 2 10 30 32 13 18 14 17 29 33 21 26 OUT1+ OUT1− OUT2+ OUT2− OUT3+ OUT3− OUT4+ OUT4− 22 GAINSEL on/standby (SW1) 28 SDA 22 µF 27 SCL SVR 23 12 DIAG 4.7 kΩ IN4− 25 11 STB 470 nF IN4+ ADSEL 470 nF n.c. 9 TDA8596 470 nF n.c. 16 dB gain open 26 dB gain 10 kΩ BC859 DZ 8.2 V 2 kΩ 18 kΩ BAW62 unmute SW2 22 kΩ legacy 1 2 3 4 10 kΩ mode I2C-bus supply 10 kΩ clip 2 10 µF mute SW3 I2C-bus 2 SDA +5V GND SCL 1 8 2 7 TDA3664 3 6 4 5 Vp 1 µF 1 address select dip switch 3 12 kΩ 4 51 kΩ diag 001aag006 Fig 31. Evaluation board; schematic TDA8596_2 Product data sheet © NXP B.V. 2007. All rights reserved. Rev. 02 — 8 November 2007 42 of 48 TDA8596 NXP Semiconductors I2C-bus controlled 4 × 45 W power amplifier with symmetrical inputs SVR Sense 22 µF C13 Vp top Gnd −OUT1+ −OUT2+ Clip2 I2C /stb +OUT4− +OUT3− address select D8 (00) TDA8596TH I2C supply enable C15 DA (01) SW5 DE (11) mode on 1 µF 2200 µF/16 V C2 D1 diag SW1 J5 C6 C5 C8 C7 C11 C12 SCL Gnd +5V SDA C14 10 µF C9 C10 SW2 26 dB gain 16 dB stby I2C 8 x 470 nF mute SW3 unmute DZ1 −IN1+ Legacy 8.2 V −IN2+ +IN4− R6 10 kΩ +IN3− Sgnd Vp Gnd NXP Semiconductors SRK ver. 2 001aag007 Fig 32. Evaluation board layout; top view bottom C3 220 nF C1 220 nF TDA8596TH ID IC1 BC859 R4 2 kΩ R2 R8 R6 R5 10 kΩ 10 kΩ 1 18 4 1 TDA3664 12 kΩ 51 kΩ R3 18 kΩ R7 22 kΩ R1 4.7 kΩ 001aag008 Fig 33. Evaluation board layout; bottom view TDA8596_2 Product data sheet © NXP B.V. 2007. All rights reserved. Rev. 02 — 8 November 2007 43 of 48 TDA8596 NXP Semiconductors I2C-bus controlled 4 × 45 W power amplifier with symmetrical inputs 14. Test information 14.1 Quality information This product has been qualified in accordance with the Automotive Electronics Council (AEC) standard Q100 - Stress test qualification for integrated circuits, and is suitable for use in automotive applications. TDA8596_2 Product data sheet © NXP B.V. 2007. All rights reserved. Rev. 02 — 8 November 2007 44 of 48 TDA8596 NXP Semiconductors I2C-bus controlled 4 × 45 W power amplifier with symmetrical inputs 15. Package outline HSOP36: plastic, heatsink small outline package; 36 leads; low stand-off height SOT851-2 D E A x c y X E2 v HE M A D1 D2 1 18 pin 1 index Q A A2 E1 (A 3) A4 θ Lp detail X 36 19 z w bp e M 0 5 10 mm scale DIMENSIONS (mm are the original dimensions) A UNIT max. A2 mm 3.5 A3 A4(1) +0.08 3.5 0.35 −0.04 3.2 D1 D2 E (2) E1 E2 e HE Lp Q 0.38 0.32 16.0 13.0 0.25 0.23 15.8 12.6 1.1 0.9 11.1 10.9 6.2 5.8 2.9 2.5 0.65 14.5 13.9 1.1 0.8 1.7 1.5 bp c D (2) v w x y 0.25 0.12 0.03 0.07 Z θ 2.55 2.20 8° 0° Notes 1. Limits per individual lead. 2. Plastic or metal protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION REFERENCES IEC JEDEC JEITA EUROPEAN PROJECTION ISSUE DATE 04-05-04 SOT851-2 Fig 34. Package outline SOT851-2 (HSOP36) TDA8596_2 Product data sheet © NXP B.V. 2007. All rights reserved. Rev. 02 — 8 November 2007 45 of 48 TDA8596 NXP Semiconductors I2C-bus controlled 4 × 45 W power amplifier with symmetrical inputs 16. Abbreviations Table 18. Abbreviations Acronym Description BCDMOS Bipolar CMOS/DMOS CMOS Complementary Metal-Oxide Semiconductor DMOS Double-diffused Metal-Oxide Semiconductor DSP Digital Signal Processor ESR Equivalent Series Resistance NMOS Negative-channel Metal-Oxide Semiconductor NMOST Negative-channel Metal-Oxide Semiconductor Transistor PMOS Positive-channel Metal-Oxide Semiconductor PMOST Positive-channel Metal-Oxide Semiconductor Transistor SOAR Safe Operating ARea 17. Revision history Table 19. Revision history Document ID Release date Data sheet status Change notice Supersedes TDA8596_2 20071108 Product data sheet - TDA8596_1 Modifications: TDA8596_1 • • Figure 30: Value of base-emitter resistor changed from 10 kΩ to 5.6 kΩ Section 14: Quality information reference updated 20070705 Preliminary data sheet TDA8596_2 Product data sheet - - © NXP B.V. 2007. All rights reserved. Rev. 02 — 8 November 2007 46 of 48 TDA8596 NXP Semiconductors I2C-bus controlled 4 × 45 W power amplifier with symmetrical inputs 18. Legal information 18.1 Data sheet status Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. [1] Please consult the most recently issued document before initiating or completing a design. [2] The term ‘short data sheet’ is explained in section “Definitions”. [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 18.2 Definitions Draft — The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet — A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. 18.3 Disclaimers General — Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Right to make changes — NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use — NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in medical, military, aircraft, space or life support equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer’s own risk. Applications — Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Limiting values — Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) may cause permanent damage to the device. Limiting values are stress ratings only and operation of the device at these or any other conditions above those given in the Characteristics sections of this document is not implied. Exposure to limiting values for extended periods may affect device reliability. Terms and conditions of sale — NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, including those pertaining to warranty, intellectual property rights infringement and limitation of liability, unless explicitly otherwise agreed to in writing by NXP Semiconductors. In case of any inconsistency or conflict between information in this document and such terms and conditions, the latter will prevail. No offer to sell or license — Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. 18.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. I2C-bus — logo is a trademark of NXP B.V. 19. Contact information For additional information, please visit: http://www.nxp.com For sales office addresses, send an email to: [email protected] TDA8596_2 Product data sheet © NXP B.V. 2007. All rights reserved. Rev. 02 — 8 November 2007 47 of 48 TDA8596 NXP Semiconductors I2C-bus controlled 4 × 45 W power amplifier with symmetrical inputs 20. Contents 1 2 2.1 2.2 3 4 5 6 6.1 6.2 7 7.1 7.2 7.3 7.4 7.4.1 7.4.2 7.5 7.5.1 7.5.2 7.6 7.7 7.8 7.9 7.10 7.11 7.12 7.13 7.14 7.15 8 8.1 8.2 9 10 11 12 13 13.1 14 14.1 15 16 17 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 I2C-bus mode . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Quick reference data . . . . . . . . . . . . . . . . . . . . . 2 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pinning information . . . . . . . . . . . . . . . . . . . . . . 4 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 4 Functional description . . . . . . . . . . . . . . . . . . . 5 Output stage . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Gain selection . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Distortion (clip-) detection. . . . . . . . . . . . . . . . . 6 Output protection and short circuit operation . . 6 SOAR protection. . . . . . . . . . . . . . . . . . . . . . . . 7 Speaker protection . . . . . . . . . . . . . . . . . . . . . . 7 Standby and mute operation. . . . . . . . . . . . . . . 7 I2C-bus mode . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Legacy mode (pin ADSEL connected to ground) . . . . . . . . . . 7 Start-up and shut-down sequence . . . . . . . . . . 8 Power-on reset and supply voltage spikes . . . 12 Engine start and low voltage operation. . . . . . 12 Overvoltage and load dump protection. . . . . . 15 Thermal pre-warning and thermal protection . 15 Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Offset detection. . . . . . . . . . . . . . . . . . . . . . . . 17 DC load detection . . . . . . . . . . . . . . . . . . . . . . 18 AC load detection . . . . . . . . . . . . . . . . . . . . . . 18 I2C-bus diagnostic bits read out . . . . . . . . . . . 19 2 I C-bus specification . . . . . . . . . . . . . . . . . . . . 20 Instruction bytes . . . . . . . . . . . . . . . . . . . . . . . 21 Data bytes. . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . 27 Thermal characteristics. . . . . . . . . . . . . . . . . . 28 Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . 28 Performance diagrams . . . . . . . . . . . . . . . . . . 34 Application information. . . . . . . . . . . . . . . . . . 40 PCB schematic and layout . . . . . . . . . . . . . . . 42 Test information . . . . . . . . . . . . . . . . . . . . . . . . 44 Quality information . . . . . . . . . . . . . . . . . . . . . 44 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 45 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 46 18 18.1 18.2 18.3 18.4 19 20 Legal information . . . . . . . . . . . . . . . . . . . . . . Data sheet status . . . . . . . . . . . . . . . . . . . . . . Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . Disclaimers. . . . . . . . . . . . . . . . . . . . . . . . . . . Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . Contact information . . . . . . . . . . . . . . . . . . . . Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 47 47 47 47 47 48 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section ‘Legal information’. © NXP B.V. 2007. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: [email protected] Date of release: 8 November 2007 Document identifier: TDA8596_2