FSA201 — USB2.0 Full-Speed and Audio Switches with Negative Signal Capability Features Description 3Ω Typical ON Resistance Power-off Protection on Common D+/R, D-/L Ports The FSA201 is a Double-Pole, Double Throw (DPDT) multiplexer that combines a low-distortion audio and a USB2.0 Full-Speed (FS) switch path. This configuration enables audio and USB data to share a common connector port. The architecture is designed to allow audio signals to swing below ground. This means a common USB and headphone jack can be used for personal media players and similar portable peripheral devices. -3db Bandwidth: > 250MHz Low Power Consumption Packaged in Pb-free 10-pin MSOP and 10-Lead MicroPak™ (1.6 x 2.1mm) Since USB2.0 is an industry standard for shared datapath in portable devices, the FSA201 also incorporates a VBUS detection capability. The FSA201 includes a power-off feature to minimize current consumption when VBUS is not present. This power-off circuitry is available for the common D+/R, D-/L ports only. Typical applications involve switching in portables and consumer applications, such as cell phones, digital cameras, and notebooks with hubs or controllers. Automatically Detects VBUS for Switch Path Selection Applications Cell Phone, PDA, Digital Camera, and Notebook LCD Monitor, TV, and Set-Top Box Ordering Information Part Number Package Number Packing Description FSA201L10X MAC010A 10-Lead MicroPak, JEDEC MO-255, 1.6 x 2.1mm FSA201MUX MUA10A 10-Lead MSOP, JEDEC MO-187, 3.0mm Wide Vbus ASel Switch Select Control Circuitry Vaudio Rpd D+ GND D+/R R D-- D-/L L Figure 1. © 2006 Fairchild Semiconductor Corporation FSA201 Rev. 1.2.2 FSA201 Analog Symbol www.fairchildsemi.com FSA201 USB2.0 Full-Speed and Audio Switches with Negative Signal Capability June 2012 Vbus 10 D+ 1 9 ASel D-- 2 8 D+/R R 3 7 D-/L L 4 6 Vaudio D+ 1 10 Vbus D- 2 9 ASel R 3 8 D+/R L 4 7 D-/L 5 6 Vaudio GND 5 GND Figure 2. MicroPak™ 10-Pin Figure 3. MSOP 10-Pin Pin Descriptions Pin # Name 1, 2 D+, D- Description USB data bus input sources 6 VAUDIO 3, 4 R, L Audio right and left input sources 9 ASEL Audio select to override auto USB detect when VAUDIO supply is present 10 VBUS 8, 7 D+/R, D-/L Power supply (audio) Power supply (USB) and auto USB switch-path select USB and audio common connector ports Truth Table ASEL(1) VAUDIO VBUS L, R D+, D- LOW LOW LOW OFF OFF (2) LOW LOW High OFF ON LOW HIGH(2) LOW ON OFF LOW HIGH(2) HIGH(2) OFF ON HIGH LOW LOW OFF OFF HIGH LOW HIGH(2) OFF ON LOW ON OFF ON OFF HIGH HIGH (2) HIGH (2) HIGH (2) HIGH Notes: 1. ASEL- Internal resistor to GND provides auto-VBUS detect if there is no external connection. Forcing ASEL HIGH when VAUDIO is present overrides the USB path even if VBUS is present. 2. H - Value is the threshold as defined to meet USB2.0 VBUS requirements and audio supply threshold in a system (see DC Tables). © 2006 Fairchild Semiconductor Corporation FSA201 Rev. 1.2.2 www.fairchildsemi.com 2 FSA201 USB2.0 Full-Speed and Audio Switches with Negative Signal Capability Pin Assignments control, to the audio path. The ASEL pin is internally terminated by a resistor to GND (typical value 3M) and requires no connection for the standard ultra-portable (cell-phone, MP3, or Portable Media Player). In an application where the supply to the FSA201 VBUS pin is not guaranteed to be removed, a GPIO pin can be used to switch out of full-speed USB mode into audio mode, using the ASEL pin. The FSA201 is a combined USB and audio switch that enables sharing the D+/D- lines of a USB connector with stereo audio CODEC outputs. The switch is optimized for full-speed USB signals and includes an automatic VBUS-detection circuit. When a USB connector, rather than a headphone, is connected to the ultra-portable device the switch is automatically configured for fullspeed USB data transfer. If no VBUS is detected, and yet VAUDIO is present, the switch is configured for the lowdistortion audio switch path. The audio switch path also handles negative signals (down to -2V), which eliminates the need for large coupling capacitors. The FSA201 VBUS pin must be connected directly to VBUS or a supply > 3.8V, not an LDO regulated down to 3.6V or a Vbat-generated supply that may fall below 3.8V in normal operation (see the Application Diagram). For those applications where the VBUS is generated as a self-powered device or where VBUS is not removed, the ASEL pin provides the ability to switch, under software Application Diagram Vbus 3.0V - 3.6V Vaudio FS-USB Source Switch Select Control Circuitry 5V D+/R Vbus Rpd D+ GND R D- Audio CODEC ASel D-/L USB Mini -AB Connector ID L GND Figure 4. © 2006 Fairchild Semiconductor Corporation FSA201 Rev. 1.2.2 Application Diagram www.fairchildsemi.com 3 FSA201 USB2.0 Full-Speed and Audio Switches with Negative Signal Capability Functional Description Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings are stress ratings only. Symbol Parameter Min. Max. Unit -0.5 6.0 V VBUS -7.0 VBUS +0.3 V VAUDIO -7.0 VAUDIO -0.3 V VAUDIO / VBus Supply Voltage D+, D-, D+/R, D-/L Pins VSW Switch I/O Voltage(3) ASEL Control Input Voltage -0.5 IIK Input Clamp Diode Current -50 ISW Switch I/O Current (Continuous) ISWPEAK TSTG R, L, Pins Peak Switch Current (Pulsed at 1ms Duration, <10% Duty Cycle) 6.0 mA USB 50 Audio 250 USB 100 Audio 500 Storage Temperature Range -65 V mA mA +150 °C TJ Maximum Junction Temperature +150 °C TL Lead Temperature (Soldering, 10 seconds) +260 °C ESD Human Body Model (JEDEC: JESD22-A114) I/O to GND 10 All Other Pins 8 Charged Discharge Model (JEDEC: JESD22-C101) kV 2 Note: 3. The input and output negative ratings may be exceeded if the input and output diode current ratings are observed. Recommended Operating Conditions The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended operating conditions are specified to ensure optimal performance to the datasheet specifications. Fairchild does not recommend exceeding them or designing to Absolute Maximum Ratings. Symbol Parameter Minimum Maximum VAUDIO Supply Voltage 2.7V 3.6V VBUS Supply Voltage 4.25V 5.50V ASEL Control Input Voltage 0V VAUDIO VSW Switch I/O Voltage VAUDIO– 6.5V VAUDIO– 0.3V -40°C 85°C TA Operating Temperature JA Thermal Resistance (free air) © 2006 Fairchild Semiconductor Corporation FSA201 Rev. 1.2.2 MicroPak 10 330ºC / W (estimated) www.fairchildsemi.com 4 FSA201 USB2.0 Full-Speed and Audio Switches with Negative Signal Capability Absolute Maximum Ratings All typical values are at 25ºC unless otherwise specified. Symbol VAUDIO (V) Parameter TA=- 40ºC to +85ºC Condition Min. Unit Typ. Max. Common Pins VIK Clamp Diode Voltage VIH Control Input Voltage HIGH 2.7 to 3.6 VIL Control Input Voltage LOW 2.7 to 3.6 IIN IOFF 2.7 ASEL Input HIGH Current 3.6 Power Off Leakage Current (Common Port Only D+/R, D-/L) INO(0FF) Off Leakage Current of Port D+, D-, R, L INC(0N) On Leakage Current of Port D+/R or D-/L USB Switch Path VAUDIO= VBUS=0V IIK=-18mA 1.3 ∆ RONUSB V 0.5 VCNTRL=0V to 3.6V -3 Common Port (D+/R, D-/L) VSW=0V to 5.5V 3 µA 1 µA 3.6 VBUS=0V, 5. 5V D+/R, D-/L=0.3V, VAUDIO – 0.3V D+, D-, R, L=0.3V, VAUDIO – 0.3V or Floating Figure 14 -50 10 50 nA 3.6 VBUS=0V, 5.5V D+/R, D-/L=0.3V, VAUDIO – 0.3V, D+, D-, R, L=Floating Figure 15 -100 50 100 nA 3.6 V 6 Ω VBUS (V) USB Analog Signal Range RONUSB -1.2 (4) FS Switch On Resistance FS Delta RON(4,6) Audio Switch Path 0 4.25 VD+/D-=0V, 3.0V, ION=-8mA Figure 6, Figure 13 4.25 VD+/D-=3V, ION=-8mA 3 0.35 Ω VAUDIO (V) VAUDIO – 6.5 Audio Analog Signal Range VAUDIO V 2.7 VL/R=-2V, 0V, 0.7V, VAUDIO0.7V, VAUDIO ION=-100mA, VBUS=0V Figure 5, Figure 13 0.5 1.0 Ω ∆ RONAudio Audio Delta RON(4) 2.7 VL/R=0.7V ION=-100mA 0.01 0.10 Ω RFLAT(Audio) Audio RON Flatness(5) 2.7 VL/R=-2V, 0V, 0.7V, 2V, 2.7V ION=-100mA 0.35 Ω RONAUDIO Audio Switch On (7) Resistance Notes: 4. ∆RON=RON max – RON min measured at identical VCC, temperature, and voltage. Worst-case signal path, audio or USB channel, is characterized. 5. Flatness is defined as the difference between the maximum and minimum values of on resistance over the specified range of conditions. 6. Guaranteed by characterization, not production tested. 7. On resistance is determined by the voltage drop between the A and B pins at the indicated current through the switch. © 2006 Fairchild Semiconductor Corporation FSA201 Rev. 1.2.2 www.fairchildsemi.com 5 FSA201 USB2.0 Full-Speed and Audio Switches with Negative Signal Capability DC Electrical Characteristics All typical values are at 25ºC unless otherwise specified. Symbol Parameter VAUDIO (V) Condition TA=- 40ºC to +85ºC Min. Typ. Max. Unit Power Supply Vbusth VBUS Threshold Voltage 3.2 3.8 V Vaudioth VAUDIO Threshold 0.5 1.5 V ICC(Audio) Quiescent Supply Current (Audio) VASEL=0 to VAUDIO, IOUT=0 10 µA ICC(VBUS) Quiescent Supply Current (VBUS) VASEL=0 to VAUDIO, IOUT=0 VBUS=5.5V 20 µA VASEL=2.6V, VBUS=Floating 15 VASEL=1.8V, VBUS=Floating 18 ICCT Increase in ICC Current per Control Voltage and VCC © 2006 Fairchild Semiconductor Corporation FSA201 Rev. 1.2.2 3.0 3.0 µA www.fairchildsemi.com 6 FSA201 USB2.0 Full-Speed and Audio Switches with Negative Signal Capability DC Electrical Characteristics (Continued) All typical value are for VAUDIO=3.3V and VBUS=5.0 at 25ºC unless otherwise specified. Condition TA=- 40°C to +85°C Symbol Parameter tONAUDIO1 Turn-On Time VAUDIO↑ to Output VD+/R, D-/L=1.0V RL=50Ω, CL=50pF Figure 16, Figure 18 10 μs tOFFAUDIO1 V D-/L=1.0V Turn-Off Time VBUS↑ to VAUDIO=2.7 for D+/R, RL=50Ω, CL=50pF Output VBUS ↑ Figure 16, Figure 18 10 μs tONAUDIO2 Turn-On Time ASEL to Output VBUS=4.25V VAUDIO=2.7 VD+/R, D-/L=1.0V RL=50Ω, CL=50pF Figure 16, Figure 17 1 μs tOFFAUDIO2 Turn-Off Time ASEL to Output VBUS =4.25V VAUDIO=2.7 VD+/R, D-/L=1.0V RL=50Ω, CL=50pF Figure 16, Figure 18 1 μs tONAUDIO3 Turn-On Time VBUS↓ to VAUDIO=2.7 Output VD+/R, D-/L=1.0V RL=50Ω, CL=50pF Figure 16, Figure 17 10 μs tONUSB Turn-On Time VUSB↑ to VAUDIO = 2.7 Output VD+/R, D-/L=1.0V RL=50Ω, CL=50pF Figure 16, Figure 18 10 μs tOFFUSB Turn-Off Time VUSB↓ to VAUDIO=2.7 Output VD+/R, D-/L=1.0V RL=50Ω, CL=50pF Figure 16, Figure 18 10 μs tPDUSB USB Switch Propagation Delay(8) VAUDIO=2.7 VBUS=4.25V RL=50Ω, CL=50pF Figure 19 0.25 ns OIRRUSB Off-Isolation - USB VAUDIO=2.7 VBUS=4.25V f=6MHz, RT=50Ω, CL=0pF Figure 8, Figure 23 -55 dB OIRRA Off-Isolation - Audio VAUDIO=2.7 VBUS=4.25V f=6MHz, RT=50Ω, CL=0pF Figure 7, Figure 23 -37 dB XtalkUSB Non-Adjacent Channel VAUDIO=2.7 Crosstalk - USB VBUS=4.25V f=6MHz, RT=50Ω, CL=0pF Figure 10, Figure 24 -49 dB XtalkA Non-Adjacent Channel VAUDIO=2.7 VBUS=4.25V Crosstalk - Audio f=6MHz, RT=50Ω, CL=0pF Figure 9, Figure 24 -39 dB RT=50Ω, CL=0pF, Signal 0dBm Figure 11, Figure 12, Figure 22 400 MHz VAUDIO/VBUS (V) VBUS = 0V Min. Typ. Max. Unit BW -3db Bandwidth VAUDIO=2.7 VBUS=4.25V THD Total Harmonic Distortion VAUDIO=2.7 VBUS=0V f=20Hz to 20kHz, RL=32Ω, VR,L=2Vpp Figure 27 0.05 % PSRR Power Supply Rejection Ratio VAUDIO=3.3 VBUS=0V f=217Hz on VAUDIO VR,L=1.0V, RT=32Ω, VRipple=600mVpp -56 dB Note: 8. Guaranteed by characterization, not production tested. © 2006 Fairchild Semiconductor Corporation FSA201 Rev. 1.2.2 www.fairchildsemi.com 7 FSA201 USB2.0 Full-Speed and Audio Switches with Negative Signal Capability AC Electrical Characteristics Symbol Parameter VAUDIO / VBUS(V) Condition TA=-40ºC to +85ºC Min. Typ. Max. Unit tSK(o) Channel-to-Channel Skew(9) VAUDIO=2.7V VBUS=4.25V tR=tF=12ns (10-90%) at 6MHz CL=50pF, RL=50Ω Figure 20, Figure 21 150 ps tSK(P) Skew of Opposite Transitions of the Same (9) Output VAUDIO=2.7V VBUS=4.25V tR=tF=12ns (10-90%) at 6MHz CL=50pF, RL=50Ω Figure 20, Figure 21 150 ps VAUDIO=2.7V VBUS=4.25V RL=50Ω, CL=50pF, tR=tF=12ns (10-90%) at 12Mbps (PRBS=215 – 1) 1.6 ns tJ Total Jitter (9) Note: 9. Guaranteed by characterization, not production tested. Capacitance Symbol Parameter CIN (ASEL) Control Pin Input Capacitance (ASEL) CON(D+/R, D-/L) VAUDIO / VBUS(V) VAUDIO=2.7V VBUS=4.25V VAUDIO=2.7V VBUS=4.25V ASEL=0V D+/R, D-/L (Common Port) (CONUSB) On Capacitance VAUDIO=2.7V VBUS=4.25V ASEL=2.7V (CONAudio) Condition TA=-40ºC to +85ºC Min. Typ. VBias=0.2V 2.5 VBias=0.2V, f=6MHz Figure 26 25 Max. Unit pF pF VBias=0.2V, f=6MHz Figure 26 29 COFF(D+, D-) USB Input Source Off Capacitance VAUDIO=2.7V VBUS=4.25V ASEL=2.7V f=6MHz, Figure 25 5 pF COFF(R/L) Audio Input Source Off Capacitance VAUDIO=2.7V VBUS=4.25V ASEL=0V f=6MHz, Figure 25 17 pF © 2006 Fairchild Semiconductor Corporation FSA201 Rev. 1.2.2 www.fairchildsemi.com 8 FSA201 USB2.0 Full-Speed and Audio Switches with Negative Signal Capability USB Full-Speed Related AC Electrical Characteristics 0.80 RON (ohms) 0.70 0.60 0.50 0.40 25°C -40°C 0.30 85°C 0.20 0.10 0.00 -4 -3 -2 -1 0 1 2 3 4 VIN (V) Figure 5. RON Audio Characterization (RON Audio R, VAUDIO=2.7V) 7 RON ( ohms) 6 5 - 40°C 25°C 85°C 4 3 2 1 0 -1 0 Figure 6. © 2006 Fairchild Semiconductor Corporation FSA201 Rev. 1.2.2 1 2 VIN (V) 3 4 5 RON USB Characterization (RON USB D+) www.fairchildsemi.com 9 FSA201 USB2.0 Full-Speed and Audio Switches with Negative Signal Capability Typical Characteristics 1 10 100 1000 0 Off Isolation (dB) -10 -20 -30 -40 -50 -60 -70 -80 Frequency (MHz) Figure 7. Off-Isolation (Audio) Characterization, Frequency Response at VCC (VAUDIO)=2.7V Off Isolation (dB) 1 10 100 1000 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 Frequency (MHz) Figure 8. Off-Isolation (USB) Characterization, Frequency Response at VCC (VBUS)=4.25V © 2006 Fairchild Semiconductor Corporation FSA201 Rev. 1.2.2 www.fairchildsemi.com 10 FSA201 USB2.0 Full-Speed and Audio Switches with Negative Signal Capability Typical Characteristics (Continued) 1 10 100 1000 Crosstalk (dB) 0 -10 -20 -30 -40 -50 -60 -70 -80 -90 -100 Frequency (MHz) Figure 9. Figure 10. Non-Adjacent Channel Crosstalk (Audio) Characterization at VCC (VAUDIO)=2.7V Non-Adjacent Channel Crosstalk (USB) Characterization at VCC (VBUS)=4.25V © 2006 Fairchild Semiconductor Corporation FSA201 Rev. 1.2.2 www.fairchildsemi.com 11 FSA201 USB2.0 Full-Speed and Audio Switches with Negative Signal Capability Typical Characteristics (Continued) Figure 11. Bandwidth Characterization, Frequency Response at CL=0pF, VCC (VAUDIO)=2.7V Figure 12. Bandwidth Characterization, Frequency Response at CL=0pF, VCC (VBUS)=4.25V © 2006 Fairchild Semiconductor Corporation FSA201 Rev. 1.2.2 www.fairchildsemi.com 12 FSA201 USB2.0 Full-Speed and Audio Switches with Negative Signal Capability Typical Characteristics (Continued) VON I (OFF) A Dn or R/L V sw D+/R or D-/L V SW I ON GND D+/R or D-/L - GND D+, D-or R/L GND V CNTRL = RON= VON / ION Figure 13. V CNTRL = fn (Vaudio and Vbus) On Resistance Figure 14. fn (Vaudio and Vbus) Off Leakage D+, D-- or R,L D+/R or D-/L - V OUT D+, D-- or R/L I A(ON) CL A D+/R or D-/L GND V sw Figure 15. RL , RS and CL are function of application environment (see AC Tables for specific values) CL includes test fixture and stray capacitance On Leakage Figure 16. AC Test Circuit Load tFALL = 2.5ns tRISE = 1µs 3V 3 90% Input - V ASel GND fn (Vaudio and Vbus) GND fn (Vaudio and Vbus) tRISE = 2.5ns V sw GND V CNTRL = GND V CNTRL = RL RS 10% 50% 50% Vbus 10% Input - V CNTRL V OH 90% 90% GND Output - V OUT V OL tFALL = 1µs 90% 10% 90% Vth(max)) Vth(min) 10% V OH 90% tON V OL V CNTRL = Figure 17. Turn-On / Turn-Off Waveforms (ASEL) © 2006 Fairchild Semiconductor Corporation FSA201 Rev. 1.2.2 90% Output - VOUT tOFF Vth = Vbusth or V audioth tON tOFF fn (Vaudio and Vbus) Figure 18. Turn-On / Turn-Off Waveforms (USB/Audio) www.fairchildsemi.com 13 FSA201 USB2.0 Full-Speed and Audio Switches with Negative Signal Capability Test Diagrams tRISE = 12ns tFALL = 12ns tRISE = 12ns 3V Input – V D+/D-GND 10% 90% 3V 90% 50% 50% 10% V OH V OL Figure 19. 90% Input – V D+/D- 50% 10% GND Output-- V OUT tFALL = 12ns 90% 50% 10% V OH Output-- V OUT 50% 50% tpLH V OL tpHL USB Switch Propagation Delay Waveforms Figure 20. tRISE = 12ns 50% 50% tpLH tpHL Pulse Skew: tSK(P)=| tPHL – tPLH | tFALL = 12ns 3V Input – V D+/DGND 10% 90% 90% 50% 50% 10% V OH Output1-- V OUT V OL 50% 50% tpLH1 tpHL1 t sk (o) V OH Output2-- V OUT V OL Figure 21. © 2006 Fairchild Semiconductor Corporation FSA201 Rev. 1.2.2 50% 50% tpLH2 tpHL2 Output Skew: tSK(O)=| tPLH1 – tPLH2 | or | tPHL1 – tPHL2 | www.fairchildsemi.com 14 FSA201 USB2.0 Full-Speed and Audio Switches with Negative Signal Capability Test Diagrams (Continued) Network Analyzer RS V IN GND VS GND V CNTRL GND VCNTRL= fn (Vaudio and Vbus) GND V OUT RT GND RS and RT are functions of the application environment (see AC Tables for specific values ) Figure 22. USB Bandwidth Network Analyzer RS V CNTRL GND V CNTRL = V IN GND RT VS GND GND V OUT fn (Vaudio andVbus) GND RT RS and RT are functions of the application environment (see AC Tables for specific values) GND OFF-Isolation = 20 Log (VOUT / VIN ) Figure 23. Channel Off Isolation Network Analyzer NC RS GND V IN VS V CNTRL GND GND RT GND V CNTRL = fn Vaudio and Vbus) GND RS and RT are functions of the application environment (see AC Tables for specific values) RT V OUT GND CROSSTALK = 20 Log (VOUT / VIN ) Figure 24. © 2006 Fairchild Semiconductor Corporation FSA201 Rev. 1.2.2 Non-Adjacent Channel-to-Channel Crosstalk www.fairchildsemi.com 15 FSA201 USB2.0 Full-Speed and Audio Switches with Negative Signal Capability Test Diagrams (Continued) FSA201 USB2.0 Full-Speed and Audio Switches with Negative Signal Capability Test Diagrams (Continued) Dn or R/L or D+/R or D-/L Capacitance Meter VCNTRL= Dn or R/L or D+/R or D-/L - f = 6MHz Figure 25. Capacitance Meter fn (VAUDIO and VBUS) Channel Off Capacitance Dn or R/L or D+/R or D-/L V CNTRL = f = 6MHz fn (Vaudio and Vbus) Dn or R/L or D+/R or D-/L Figure 26. Channel On Capacitance Audio Analyzer RS GND V IN VS GND V CNTRL GND VCNTRL = fn (Vaudio and Vbus) GND RT V OUT GND RS and RT are functions of the application environment (see AC Tables for specific values) Figure 27. © 2006 Fairchild Semiconductor Corporation FSA201 Rev. 1.2.2 Total Harmonic Distortion www.fairchildsemi.com 16 0.10 C 2.10 2X A 1.62 B KEEPOUT ZONE, NO TRACES OR VIAS ALLOWED (0.11) PIN1 IDENT IS 2X LONGER THAN OTHER LINES 0.56 1.12 1.60 0.10 C 2X TOP VIEW (0.35) 10X (0.25) 10X 0.50 RECOMMENDED LAND PATTERN 0.55 MAX 0.05 C 0.05 C 0.05 0.00 C (0.20) 0.35 0.25 SIDE VIEW D 0.65 0.55 DETAIL A 0.35 0.25 4 1 0.35 0.25 DETAIL A 2X SCALE 0.56 10 (0.29) (0.15) (0.36) NOTES: A. PACKAGE CONFORMS TO JEDEC REGISTRATION MO-255, VARIATION UABD . B. DIMENSIONS ARE IN MILLIMETERS. C. DIMENSIONS AND TOLERANCES PER ASME Y14.5M, 1994. D. PRESENCE OF CENTER PAD IS PACKAGE SUPPLIER DEPENDENT. IF PRESENT IT IS NOT INTENDED TO BE SOLDERED AND HAS A BLACK OXIDE FINISH. E. DRAWING FILENAME: MKT-MAC10Arev5. 5 6 9 0.50 0.25 9X 0.15 1.62 0.35 9X 0.25 0.10 0.05 C A B C ALL FEATURES BOTTOM VIEW Figure 28. Package Designator L10X 10-Lead MicroPak™ Tape Section Number Cavity Cavity Status Cover Tape Status Leader (Start End) 125 (typical) Empty Sealed Carrier 5000 Filled Sealed Trailer (Hub End) 75 (typical) Empty Sealed Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild’s worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. Always visit Fairchild Semiconductor’s online packaging area for the most recent package drawings: http://www.fairchildsemi.com/packaging/. For current tape and reel specifications, visit Fairchild Semiconductor’s online packaging area: http://www.fairchildsemi.com/products/logic/pdf/micropak_tr.pdf. © 2006 Fairchild Semiconductor Corporation FSA201 Rev. 1.2.2 www.fairchildsemi.com 17 FSA201 USB2.0 Full-Speed and Audio Switches with Negative Signal Capability Physical Dimensions FSA201 USB2.0 Full-Speed and Audio Switches with Negative Signal Capability Physical Dimensions Figure 29. 10-Lead Molded Small Outline Package (MSOP) Tape Size A B C D N 13 0.059 (12mm) (330) (1.5) 0.512 0.795 7.008 (13) (20.2) (178) W1 W2 W3 0.448 0.724 0.486-0.606 (12.4) (18.4) (11.9-15.4) Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild’s worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. Always visit Fairchild Semiconductor’s online packaging area for the most recent package drawings: http://www.fairchildsemi.com/packaging/. For current tape and reel specifications, visit Fairchild Semiconductor’s online packaging area: http://www.fairchildsemi.com/products/analog/pdf/msop10_tr.pdf. © 2006 Fairchild Semiconductor Corporation FSA201 Rev. 1.2.2 www.fairchildsemi.com 18 FSA201 USB2.0 Full-Speed and Audio Switches with Negative Signal Capability © 2006 Fairchild Semiconductor Corporation FSA201 Rev. 1.2.2 www.fairchildsemi.com 19