Get Datasheet - Rochester Electronics

REI Datasheet
MM74C911
4-Digit Expandable Segment Display Controller
The MM74C911 display controller is an interface element with memory that drives a 4-digit,
8-segment LED display. The MM74C911 allows individual control of any segment in the 4-digit
display. The number of segments per digit can be expanded without any external components. For
example, two MM74C911’s can be cascaded to drive a 16-segment alpha-numeric display.
Rochester Electronics
Manufactured Components
Rochester branded components are
manufactured using either die/wafers
purchased from the original suppliers
or Rochester wafers recreated from the
original IP. All recreations are done with
the approval of the OCM.
Parts are tested using original factory
test programs or Rochester developed
test solutions to guarantee product
meets or exceeds the OCM data sheet.
Quality Overview
•
•
•
•
ISO-9001
AS9120 certification
Qualified Manufacturers List (QML) MIL-PRF-38535
• Class Q Military
• Class V Space Level
Qualified Suppliers List of Distributors (QSLD)
•
Rochester
is a critical supplier to DLA and
meets all industry and DLA standards.
Rochester Electronics, LLC is committed to supplying
products that satisfy customer expectations for
quality and are equal to those originally supplied by
industry manufacturers.
The original manufacturer’s datasheet accompanying this document reflects the performance
and specifications of the Rochester manufactured version of this device. Rochester Electronics
guarantees the performance of its semiconductor products to the original OEM specifications.
‘Typical’ values are for reference purposes only. Certain minimum or maximum ratings may be
based on product characterization, design, simulation, or sample testing.
© 2014 Rochester Electronics, LLC. All Rights Reserved 01202014
To learn more, please visit www.rocelec.com
Revised January 1999
MM74C911
4-Digit Expandable Segment Display Controller
General Description
The MM74C911 display controller is an interface element
with memory that drives a 4-digit, 8-segment LED display.
The MM74C911 allows individual control of any segment in
the 4-digit display. The number of segments per digit can
be expanded without any external components. For example, two MM74C911’s can be cascaded to drive a 16-segment alpha-numeric display.
The display controllers receive data information through 8
data lines a, b…DP, and digit information through 2
address inputs K1 and K2. The input data is written into the
register selected by the address information when CHIP
ENABLE, CE, and WRITE ENABLE, WE, are LOW and is
latched when either CE or WE return HIGH. Data hold time
is not required.
A self-contained internal oscillator sequentially presents
the stored data to high drive (100 mA typ.) 3-STATE output
drivers which directly drive the LED display. The drivers are
active when the control pin labeled SEGMENT OUTPUT
ENABLE, SOE, is LOW and go into 3-STATE when SOE is
HIGH. This feature allows for duty cycle brightness control,
or for disabling the output drive for power conservation.
The digit outputs directly drive the base of the digit transistor when the control pin labeled DIGIT INPUT OUTPUT,
DIO, is LOW. When DIO is HIGH, the digit lines turn into
inputs and the internal scanning multiplexer is disabled.
When any digit line is forced HIGH by an external device,
usually another MM74C911, the data information for that
digit is presented to the output. In this manner, 16-segment
alpha-numeric displays, 24- or 32-segment displays, or an
array of discrete LED's can be controlled by the simple cascading of expandable segment display controllers. All
inputs except digit inputs are TTL compatible and do not
clamp input voltages above VCC.
Features
■ Direct segment drive (100 mA typ.) 3-STATE
■ 4 registers addressed like RAM
■ Internal oscillator and scanning circuit
■ Direct base drive to digit transistor
■ Segment expandability without external components
■ TTL compatible inputs
■ Power saver mode—5 µW (typ.)
Ordering Code:
Order Number
MM74C991N
Package Number
N28B
Package Description
28-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS−010, 0.600” Wide
Connection Diagram
Pin Assignments for DIP
Top View
© 1999 Fairchild Semiconductor Corporation
DS005915.prf
www.fairchildsemi.com
MM74C911 4-Digit Expandable Segment Display Controller
October 1987
MM74C911
Truth Tables
Input Control
Output Control
Digit
CE
Address
WE
DIO
SOE
0
0
Operation
Digit Lines
Operation
D4 D3 D2 D1
K2
K1
R
R
R
R
Refresh Display
0
0
0
0
Write Digit 1
0
1
R
R
R
R
Disable Segment Outputs
0
0
0
1
Latch Digit 1
1
0
0
0
0
0
Digits Are Now Inputs
0
0
1
0
Write Digit 2
1
0
0
0
0
1
Display Digit 1
0
0
1
1
Latch Digit 2
1
0
0
0
1
0
Display Digit 2
0
1
0
0
Write Digit 3
1
0
0
1
0
0
Display Digit 3
0
1
0
1
Latch Digit 3
1
0
1
0
0
0
Display Digit 4
0
1
1
0
Write Digit 4
1
1
0
0
0
0
Power Saver Mode
0
1
1
1
Latch Digit 4
1
X
X
X
Disable Writing
R = Refresh (digit lines sequentially pulsed)
X = Don’t Care
Functional Description
ten into. In normal operation, the internal multiplexer scans
the registers and refreshes the display. In cascaded operation, 1 MM74C911 serves as a master refresh device and
cascaded MM74C911’s are slaved to it through digit lines
operating as inputs.
The MM74C911 display controller is manufactured on standard metal gate CMOS technology. A single 5V 74 series
TTL supply can be used for power and should be bypassed
at the VCC pin to suppress current transients.
The digit outputs directly drive the base of a grounded
emitter digit transistor without the need of a Darlington configuration. If an MM74C911 is driving a digit transistor and
also supplying digit information to a cascaded MM74C911,
base resistors are needed in the digit transistors to provide
an adequate high level to the digit inputs of the cascaded
MM74C911.
The MM74C911 appears to a microprocessor as memory
and to the user as a self-scan display. Since every segment is under microprocessor control, great versatility is
obtained.
Low power standby operation occurs with both SOE and
DIO inputs HIGH. This condition forces the MM74C911 to a
quiescent state typically drawing less than 1 µA of supply
current with a standby supply voltage as low as 3V.
As seen in the Block Diagram, these display controllers
contain four 8-bit registers; any one may be randomly writ-
Logic Diagram
www.fairchildsemi.com
2
Operating VCC Range
Absolute Maximum VCC
3V to 6V
6.5V
Lead Temperature
Voltage at Any Pin
(Soldering, 10 seconds)
−0.3V to VCC + 0.3V
except Inputs
Voltage at Any Input
Note 1: “Absolute Maximum Ratings” are those values beyond which the
safety of the device cannot be guaranteed. Except for “Operating Range”,
they are not meant to imply that the device should be operated at these limits. The table of “Electrical Characteristics” provides conditions for actual
device operation.
−0.3V to +15V
except Digits
Operating Temperature
−40°C to +85°C
Range, (TA)
−65°C to +150°C
Storage Temperature Range
Power Dissipation (PD)
260°C
Note 2: All voltage reference to ground.
Refer to PD(MAX) vs TA Graph
DC Electrical Characteristics
Min/Max limits apply at −40°C ≤ TJ ≤ +85°C, unless otherwise noted
Symbol
Parameter
Conditions
VCC = 5V
VIN(1)
Logical “1” Input Voltage
VIN(0)
Logical “0” Input Voltage
IIN(1)
Logical “1” Input Current
VCC = 5V, VIN = 15V
IIN(0)
Logical “0” Input Current
VCC = 5V, VIN = 0V
ICC
Supply Current (Normal)
VCC = 5V, Outputs Open
ICC
Supply Current (Power Saver)
Min
Typ
Max
3.0
V
1.5
V
1.0
µA
0.50
2.5
mA
1
600
µA
0.03
10
µA
0.8
V
0.005
−1.0
VCC = 5V, SOE, DIO = “1”,
Units
−0.005
µA
D1, D2, D3, D4 = “0”
IOUT
3-STATE Output Current
VO = 5V
VO = 0V
−10
−0.03
CMOS/LPTTL INTERFACE
VIN(1)
Logical “1” Input Voltage
VCC = 4.75V
VIN(0)
Logical “0” Input Voltage
VCC = 4.75V
VCC − 2
V
OUTPUT DRIVE
ISH
IDH
HIGH Level Segment Current
HIGH Level Digit Current
VCC = 5V, VO = 3.4V
TJ = 25°C
−60
−100
mA
TJ = 100°C
−40
−60
mA
TJ = 25°C
−10
−20
mA
TJ = 100°C
−7
−10
mA
TJ = 25°C
−15
−40
mA
TJ = 100°C
−10
−15
mA
VCC = 5V, IO = −360 µA
4.6
VCC = 5V, VO = 3V
VCC = 5V, VO = 1V
VOUT(1)
Logical “1” Output Voltage,
V
Any Digit
VOUT(0)
Logical “0” Output Voltage,
VCC = 5V, IO = 360 µA
0.4
V
Any Output
θJA
Thermal Resistance
(Note 3)
100
°C/W
Note 3: θJA measured in free-air with device soldered into printed circuit board.
3
www.fairchildsemi.com
MM74C911
Absolute Maximum Ratings(Note 1)
(Note 2)
MM74C911
AC Electrical Characteristics
(Note 4)
VCC = 5V, tr = tf = 20 ns, CL = 50 pF
Symbol
tCW
tAW
tWW
tDW
tWD
tWA
tWC
t1H, t0H
tH1, tH0
tD1, tD0
tIB
Parameter
Chip Enable to Write Enable Set-Up Time
Address to Write Enable Set-Up Time
Write Enable Width
Data to Write Enable Set-Up Time
Write Enable to Data Hold Time
Write Enable to Address Hold Time
Write Enable to Chip Enable Hold Time
Min
Typ
TJ = 25°C
Conditions
35
15
Max
Units
ns
TJ = 125°C
50
20
ns
TJ = 25°C
35
15
ns
TJ = 125°C
50
20
ns
TJ = 25°C
400
225
ns
TJ = 125°C
450
250
ns
TJ = 25°C
390
225
ns
TJ = 125°C
430
250
ns
TJ = 25°C
0
−10
ns
TJ = 125°C
0
−15
ns
TJ = 25°C
0
−10
ns
TJ = 125°C
0
−15
ns
TJ = 25°C
55
30
ns
TJ = 125°C
75
40
ns
Logical “1”, Logical “0” Levels into 3-STATE RL=10k, CL=10 pF
TJ = 25°C
275
500
ns
TJ = 125°C
325
600
ns
3-STATE to Logical “1” or
RL=10k, CL=10 pF
Logical “0” Levels
TJ = 25°C
325
600
ns
TJ = 125°C
375
700
ns
Propagation Delay from Digit Input to
TJ = 25°C
500
1000
ns
Segment Output
TJ = 125°C
700
1400
ns
Interdigit Blanking Time
TJ = 25°C
5
10
TJ = 125°C
10
20
µs
TJ = 25°C
525
Hz
TJ = 125°C
375
µs
fMUX
Multiplex Scan Frequency
CIN
Input Capacitance
(Note 5)
5
7.5
pF
COUT
3-STATE Output Capacitance
(Note 5)
30
50
pF
Note 4: AC Parameters are guaranteed by DC correlated testing.
Note 5: Capacitance guaranteed by periodic testing.
Switching Time Waveforms
Write Data Waveforms
www.fairchildsemi.com
3-STATE Waveforms
4
Hz
(Continued)
Multiplexing Output Waveforms
Read Data Waveforms
Note A: All other digit lines are at a low level. DIO at a HIGH level.
Typical Performance Characteristics
VCE is the saturation voltage of the digit drive transistor.
Segment outputs if shorted to ground will exceed maximum
power dissipation of the device.
Power Dissipation vs
Temperature for
Plastic Packages
Applications
Segment Output Structure
Digit Output Structure
5
www.fairchildsemi.com
MM74C911
Switching Time Waveforms
MM74C911
Input Protection
Segment Expansion
Typical Application
*Base resistors may be necessary to limit base current.
www.fairchildsemi.com
6
MM74C911
4-Digit, 16-Segment Alpha-Numeric Display
Segment
Identification
7
www.fairchildsemi.com
MM74C911 4-Digit Expandable Segment Display Controller
Physical Dimensions inches (millimeters) unless otherwise noted
28-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-010, 0.600” Wide
Package Number N28B
LIFE SUPPORT POLICY
FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD
SEMICONDUCTOR CORPORATION. As used herein:
2. A critical component in any component of a life support
1. Life support devices or systems are devices or systems
device or system whose failure to perform can be reawhich, (a) are intended for surgical implant into the
sonably expected to cause the failure of the life support
body, or (b) support or sustain life, and (c) whose failure
device or system, or to affect its safety or effectiveness.
to perform when properly used in accordance with
instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the
www.fairchildsemi.com
user.
Fairchild does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and Fairchild reserves the right at any time without notice to change said circuitry and specifications.