To all our customers
Regarding the change of names mentioned in the document, such as Mitsubishi
Electric and Mitsubishi XX, to Renesas Technology Corp.
The semiconductor operations of Hitachi and Mitsubishi Electric were transferred to Renesas
Technology Corporation on April 1st 2003. These operations include microcomputer, logic, analog
and discrete devices, and memory chips other than DRAMs (flash memory, SRAMs etc.)
Accordingly, although Mitsubishi Electric, Mitsubishi Electric Corporation, Mitsubishi
Semiconductors, and other Mitsubishi brand names are mentioned in the document, these names
have in fact all been changed to Renesas Technology Corp. Thank you for your understanding.
Except for our corporate trademark, logo and corporate statement, no changes whatsoever have been
made to the contents of the document, and these changes do not constitute any alteration to the
contents of the document itself.
Note : Mitsubishi Electric will continue the business operations of high frequency & optical devices
and power devices.
Renesas Technology Corp.
Customer Support Dept.
April 1, 2003
MITSUBISHI MICROCOMPUTERS
M35060-XXXSP
SCREEN CHARACTER and PATTERN DISPLAY CONTROLLERS
DESCRIPTION
M35060-XXXSP is CATV screen display control IC which can display 40 (horizontal) ✕ 16 (vertical). It has built-in SYRAM which can
be used with character ROM.
It uses a silicon gate CMOS process and it housed in a small 32-pin
shrink DIP package. For M35060-001SP and M35060-002SP that
are standard ROM version of M35060-XXXSP, the character patterns are also mentioned.
• Screen composition ................................ 40 characters ✕ 17 lines
(at scrolling ........................................... 40 characters ✕ 16 lines)
• Number of characters displayed .................................. 680 (Max.)
• Character composition ..................................... 12 ✕ 13 dot matrix
• Characters available character ROM .................. 256 characters
SYRAM ............................... 63 characters
• Character sizes available horizontal ................... 2 (once, twice)
vertical ....................... 2 (once, twice)
setting by every line
• Display locations available
Horizontal direction ............................................... 480 locations
Vertical direction .................................................... 235 locations
• Blinking .................................................................. character units
Cycle ... approximately 1 second, or approximately 0.5 seconds
Duty ................................................................ 25%, 50% or 75%
• Data input ............................................................ 8-bit parallel ✕ 3
• Coloring Character coloring ....... 8 colors choices per character
Background coloring .... 8 colors choices per character
Raster coloring ................ 8 colors choices per screen
• Blanking
Character size blanking
Border size blanking
Matrix-outline
Halftone blanking
Can be set by every line
• General-purpose output ports
Combined port output ............. 6
(switching to RGB output)
• RAM erase .............................. Display RAM erasing by every line
SYRAM erasing separately
• Scrolling ............ Bit by bit smooth scroll implemented by software
• Composite synchronizating signal generation .................... Built-in
(PAL, NTSC, M-PAL)
• Display oscillation circuit ..................................................... Built-in
• Synchronous separation circuit .......................................... Built-in
• Synchronous correction circuit ........................................... Built-in
Note: Superimpose black and white display. (NTSC, PAL, M-PAL)
Rev.1.3
AD0
1
32
CS
AD1
2
31
SCK
AD2
3
30
TESTA
AD3
4
29
P5
AD4
5
28
P4
AD5
AD6
6
27
P3
26
P2
AD7
8
25
P1
AC
9
24
VDD1
10
23
P0
TESTB
22
OSCIN
21
OSCOUT
7
M35060-XXXSP
FEATURES
PIN CONFIGURATION (TOP VIEW)
VSS
11
CVIDEO
12
LECHA
13
20
LP2
LEBK
14
19
VDD2
CVIN
15
18
LP1
HOR
16
17
VREF
Outline 32P4B
MITSUBISHI MICROCOMPUTERS
M35060-XXXSP
SCREEN CHARACTER and PATTERN DISPLAY CONTROLLERS
PIN DESCRIPTION
Symbol
AD0~AD7
Pin name
Parallel data input
AC
Auto-clear input
VDD1
Power pin
Earthing pin
VSS
CVIDEO
Composite video
signal output
LECHA
Character level input
LEBK
CVIN
Black level input
Composite video
signal input
HOR
Synchronous signal
input
Slice level input
VREF
LP1
VDD2
LP2
OSCOUT
OSCIN
TESTB
P0
P1
P2
P3
P4
P5
TESTA
SCK
CS
2
Input/Output
Input
Input
—
—
Output
Input
Input
Input
Input
Input
Filter output 1
Power pin
Filter output 2
Output
—
Output
The pins for attaching an external oscillator circuit for generating the synchronization signal.
Output
Test input
Port output
Port output
Port output
Port output
Port output
Port output
Test input
Clock input for data
input
Chip select input
Input
Output
Output
Output
Output
Output
Output
Input
Input
Input
Input
Function
These input pins determine address and data of the Display RAM, Control RAM, and
Overlay RAM (SYRAM) by 8-bit parallel. Hysteresis input is required.
When this input pin transitions from “H” to “L”, the device is reset. Built-in a pull-up
resistor. Hysteresis input is required.
Digital power supply pin. This pin must be connected to + 5V.
Ground pin. This pin must be connected to 0V.
This pin outputs the composite video signal. The output signal is 2Vp-p. In superimpose mode, this pin’s signal consists of the OSD signal combined with the input
composite signal CVIN.
This input pin is used for controlling the “white” character color level of the OSD signal.
This input pin is used for controlling the “black” character color level of the OSD signal.
This input pin is used for the superimpose mode. An external composite signal may be
input through this pin and mixed with the internally generated OSD signal.
This input pin is used to input the same signal as CVIN. The horizontal and vertical
sync signals are then extracted internally within the device.
This input pin is used to determine the slice voltage for extracting the sync signals from
the video composite signal.
This is filter output pin 1.
Analog power supply pin. This pin must be connected to +5V.
This is filter output pin 2.
These are the pins for attaching an external oscillator circuit for generating the
synchronization signal:
NTSC (3.580MHz), PAL (4.434MHz), M-PAL (3.576MHz).
Factory test pin. The pin must be connected to GND.
This output pin can be configured to port P0 or YM output.
This output pin can be configured to port P1 or BLNK output.
This output pin can be configured to port P2 or B output.
This output pin can be configured to port P3 or G output.
This output pin can be configured to port P4 or R output.
This output pin can be configured to port P5 or CSYN output.
Factory test pin. The pin must be connected to GND.
This pin is enabled when the CS pin is “L”. Data input to pins AD0 to AD7 is latched at
the rising edge of this signal. This pin is hysteresis input.
This is chip selection input pin. When this pin is “L”, transmission is enabled. This pin is
hysteresis input.
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
8
7
6
5
4
3
2
1
32
CS
19
VDD2
10
VDD1
VSS
11
Shift
Blinking
AC
9
SYRAM
Display RAM
Write access
control
Character
Pattern ROM
Input control circuit
31
SCK
BLOCK DIAGRAM
Display control
25
26
27
P0 P1 P2 P3
/YM /BLNK /B /G
24
Sync
generation
Timing
generator
P4
/R
28
Port output/Selection
Display
position
detection
Display control register
Read access
control
30
TESTA
29
P5
/CSYN
17
Video signal
output
NTSC, PAL,
M-PAL
Quadruple
frequency circuit
Synchronous
correction circuit
Vsync
separation
Sync
separation
16
HOR VREF
LECHA
CVIDEO
12
LEBK
14
13
CVIN
TESTB
23
15
LP2
20
OSCIN
OSCOUT
21
22
LP1
18
MITSUBISHI MICROCOMPUTERS
M35060-XXXSP
SCREEN CHARACTER and PATTERN DISPLAY CONTROLLERS
3
MITSUBISHI MICROCOMPUTERS
M35060-XXXSP
SCREEN CHARACTER and PATTERN DISPLAY CONTROLLERS
MEMORY CONSTRUCTION
The internal circuit is reset and all display control registers (address
2A816 to 2B016) are set to “0”. The memory constitution of display
RAM and register is shown in Figure 1 and the memory constitution
of SYRAM is shown in Figure 2.
Address 00016 to 2A716 are assigned to the display RAM, 2A816 to
2B016 are assigned to the display control registers and 30016 to
6EC16 are assigned to SYRAM.
Table 1 The memory constitution of display RAM and register
addDA17 DA16 DA15 DA14 DA13 DA12 DA11 DA10 DAF
ress
~
00016 SB
SG
DAE
DAD
DAC
DAA
DA9
DA8
DA7
DA6
DA5
DA4
DA3
DA2
DA1
DA0
SR SYC5 SYC4 SYC3 SYC2 SYC1 SYC0 BB
BG
BR BLINK CB
CG
CR
C7
C6
C5
C4
C3
C2
C1
C0
C1
C0
SY color setting
SG
2A816
–
2A916
–
2AA16
–
2AB16
–
2AC16
–
2AD16
–
TEST TEST TEST
3
2
1
BLINK
–
–
3
TEST
–
–
12
TEST
TEST
–
25
26
TEST
–
–
21
TEST TEST SERS
3
23
22
2AE16
–
–
Raster color setting BLINK Character color setting
SYRAM setting
2A716 SB
SR SYC5 SYC4 SYC3 SYC2 SYC1 SYC0 BB
–
–
TEST TEST TEST
10
0
11
BLINK BLINK BLINK
0
2
1
TEST
HIDE
EQP
20
PHASE PHASE PHASE
2
1
0
LINE LINE LINE
B
G
R
SERS SERS SERS
2
1
0
SEND
SEND
–
4
3
DAB
BG
BR BLINK CB
CG
CR
Character setting
C7
C6
C5
C4
C3
C2
HP8 HP7 HP6 HP5 HP4 HP3 HP2 HP1 HP0 VP7 VP6 VP5 VP4 VP3 VP2 VP1 VP0
HSZ
16
VSZ
16
HSZ
15
VSZ
15
HSZ
14
VSZ
14
HSZ
13
VSZ
13
HSZ
12
VSZ
12
HSZ
11
VSZ
11
HSZ
10
VSZ
10
HSZ
9
VSZ
9
HSZ
8
VSZ
8
HSZ
7
VSZ
7
HSZ
6
VSZ
6
HSZ
5
VSZ
5
HSZ
4
VSZ
4
HSZ
3
VSZ
3
HSZ
2
VSZ
2
HSZ
1
VSZ
1
HSZ
0
VSZ
0
DSP0
16
DSP1
16
ERS
16
SEND
2
DSP0
15
DSP1
15
ERS
15
SEND
1
DSP0
14
DSP1
14
ERS
14
SEND
0
DSP0
13
DSP1
13
ERS
13
SST
4
DSP0
12
DSP1
12
ERS
12
SST
3
DSP0
11
DSP1
11
ERS
11
SST
2
DSP0
10
DSP1
10
ERS
10
SST
1
DSP0
09
DSP1
09
ERS
9
SST
0
DSP0
08
DSP1
08
ERS
8
SLIN
4
DSP0
07
DSP1
07
ERS
7
SLIN
3
DSP0
06
DSP1
06
ERS
6
SLIN
2
DSP0
05
DSP1
05
ERS
5
SLIN
1
DSP0
04
DSP1
04
ERS
4
SLIN
0
DSP0
03
DSP1
03
ERS
3
SBIT
3
DSP0
02
DSP1
02
ERS
2
SBIT
2
DSP0
01
DSP1
01
ERS
1
SBIT
1
DSP0
00
DSP1
00
ERS
0
SBIT
0
2AF16 PC7 PC6 PC5 PC4 PC3 PC2 PC1 PC0 ALL24 SRAND SRAND SRAND PTD PTD PTD PTD PTD PTD PTC PTC PTC PTC PTC PTC
2
1
0
5
4
3
2
1
0
5
4
3
2
1
0
INT
TEST
TEST
TEST
TEST
LEVEL
LEVEL
LEVEL
PAL
TEST
TEST
DSP
DSP
SEL
2B016 –
MPAL PALH
SEPV1 SEPV0 BLK –
–
–
EX
NON NTSC
19
18
17
24
2
1
0
16
15
ONV ON
COR
TESTn (n = number) is MITSUBISHI test memory. Set 0 to all bits.
DAC
DAB
DAA
DA9
DA8
DA7
DA6
DA5
DA4
DA3
DA2
DA1
DA0
SYEX
S00B
S00A
S009
S008
S007
S006
S005
S004
S003
S002
S001
S000
SYEX
SYEX
S00B
S01B
S00A
S01A
S009
S019
S008
S018
S007
S017
S006
S016
S005
S015
S004
S014
S003
S013
S002
S012
S001
S011
S000
S010
…
…
…
…
…
…
…
…
…
…
…
…
SYEX
S01B
S01A
S019
S018
S017
SYEX
S3DB
S3DA
S3D9
S3D8
S3D7
S3D6
…
…
…
…
…
…
…
…
…
…
SYEX
SYEX
S3DB
S3EB
S3DA
S3EA
S3D9
S3E9
S3D8
S3E8
S3D7
S3E7
S3D6
S3E6
S3D5
S3E5
S3D4
S3E4
S3D3
S3E3
…
…
…
…
…
…
…
…
…
SYEX
S3EB
S3EA
S3E9
S3E8
S3E7
S3E6
S3E5
S3E4
S3E3
…~
4
…
…
…
…
S015
S014
S013
S012
S011
S010
S3D5
S3D4
S3D3
S3D2
S3D1
S3D0
…
…
…
S3D2
S3E2
S3D1
S3E1
S3D0
S3E0
…
…
S3E2
S3E1
S3E0
~
: Name or value changes by definite ratio.
: The same name or value continues.
0116
~
…
…
S016
…
0
…
…
6EC16
…
…
~
6DC16
6E016
…
…
0
…
…
~
6D016
SYRAM code
0016
…
…
~
~
~
addDA17 ~ DAD
ress
30016
0
30C16
31016
0
31C16
…
Table 2 The memory constitution of SYRAM
3D16
3E16
The hexadecimal numbers in the boxes show the display RAM address
Line 16 280 281 282 283 284 285 286 287 288 289 28A 28B 28C 28D 28E 28F 290 291 292 293 294 295 296 297 298 299 29A 29B 29C 29D 29E 29F 2A0 2A1 2A2 2A3 2A4 2A5 2A6 2A7
Line 15 258 259 25A 25B 25C 25D 25E 25F 260 261 262 263 264 265 266 267 268 269 26A 26B 26C 26D 26E 26F 270 271 272 273 274 275 276 277 278 279 27A 27B 27C 27D 27E 27F
230 231 232 233 234 235 236 237 238 239 23A 23B 23C 23D 23E 23F 240 241 242 243 244 245 246 247 248 249 24A 24B 24C 24D 24E 24F 250 251 252 253 254 255 256 257
208 209 20A 20B 20C 20D 20E 20F 210 211 212 213 214 215 216 217 218 219 21A 21B 21C 21D 21E 21F 220 221 222 223 224 225 226 227 228 229 22A 22B 22C 22D 22E 22F
1E0 1E1 1E2 1E3 1E4 1E5 1E6 1E7 1E8 1E9 1EA 1EB 1EC 1ED 1EE 1EF 1F0 1F1 1F2 1F3 1F4 1F5 1F6 1F7 1F8 1F9 1FA 1FB 1FC 1FD 1FE 1FF 200 201 202 203 204 205 206 207
1B8 1B9 1BA 1BB 1BC 1BD 1BE 1BF 1C0 1C1 1C2 1C3 1C4 1C5 1C6 1C7 1C8 1C9 1CA 1CB 1CC 1CD 1CE 1CF 1D0 1D1 1D2 1D3 1D4 1D5 1D6 1D7 1D8 1D9 1DA 1DB 1DC 1DD 1DE 1DF
190 191 192 193 194 195 196 197 198 199 19A 19B 19C 19D 19E 19F 1A0 1A1 1A2 1A3 1A4 1A5 1A6 1A7 1A8 1A9 1AA 1AB 1AC 1AD 1AE 1AF 1B0 1B1 1B2 1B3 1B4 1B5 1B6 1B7
168 169 16A 16B 16C 16D 16E 16F 170 171 172 173 174 175 176 177 178 179 17A 17B 17C 17D 17E 17F 180 181 182 183 184 185 186 187 188 189 18A 18B 18C 18D 18E 18F
140 141 142 143 144 145 146 147 148 149 14A 14B 14C 14D 14E 14F 150 151 152 153 154 155 156 157 158 159 15A 15B 15C 15D 15E 15F 160 161 162 163 164 165 166 167
118 119 11A 11B 11C 11D 11E 11F 120 121 122 123 124 125 126 127 128 129 12A 12B 12C 12D 12E 12F 130 131 132 133 134 135 136 137 138 139 13A 13B 13C 13D 13E 13F
0F0 0F1 0F2 0F3 0F4 0F5 0F6 0F7 0F8 0F9 0FA 0FB 0FC 0FD 0FE 0FF 100 101 102 103 104 105 106 107 108 109 10A 10B 10C 10D 10E 10F 110 111 112 113 114 115 116 117
0C8 0C9 0CA 0CB 0CC 0CD 0CE 0CF 0D0 0D1 0D2 0D3 0D4 0D5 0D6 0D7 0D8 0D9 0DA 0DB 0DC 0DD 0DE 0DF 0E0 0E1 0E2 0E3 0E4 0E5 0E6 0E7 0E8 0E9 0EA 0EB 0EC 0ED 0EE 0EF
0A0 0A1 0A2 0A3 0A4 0A5 0A6 0A7 0A8 0A9 0AA 0AB 0AC 0AD 0AE 0AF 0B0 0B1 0B2 0B3 0B4 0B5 0B6 0B7 0B8 0B9 0BA 0BB 0BC 0BD 0BE 0BF 0C0 0C1 0C2 0C3 0C4 0C5 0C6 0C7
078 079 07A 07B 07C 07D 07E 07F 080 081 082 083 084 085 086 087 088 089 08A 08B 08C 08D 08E 08F 090 091 092 093 094 095 096 097 098 099 09A 09B 09C 09D 09E 09F
050 051 052 053 054 055 056 057 058 059 05A 05B 05C 05D 05E 05F 060 061 062 063 064 065 066 067 068 069 06A 06B 06C 06D 06E 06F 070 071 072 073 074 075 076 077
Line 1 028 029 02A 02B 02C 02D 02E 02F 030 031 032 033 034 035 036 037 038 039 03A 03B 03C 03D 03E 03F 040 041 042 043 044 045 046 047 048 049 04A 04B 04C 04D 04E 04F
Line 0 000 001 002 003 004 005 006 007 008 009 00A 00B 00C 00D 00E 00F 010 011 012 013 014 015 016 017 018 019 01A 01B 01C 01D 01E 01F 020 021 022 023 024 025 026 027
Row
MITSUBISHI MICROCOMPUTERS
M35060-XXXSP
SCREEN CHARACTER and PATTERN DISPLAY CONTROLLERS
SCREEN CONSTITUTION
The screen lines and rows are determined from each address of the display RAM.
The screen constitution is shown in Figure 1.
Fig. 1 Screen constitution
5
MITSUBISHI MICROCOMPUTERS
M35060-XXXSP
SCREEN CHARACTER and PATTERN DISPLAY CONTROLLERS
REGISTERS DESCRIPTION
(1) Address 2A816
Register
0
VP0
1
VP1
2
VP2
3
VP3
4
VP4
5
VP5
6
VP6
7
VP7
8
HP0
9
HP1
A
HP2
B
HP3
C
HP4
D
E
HP6
F
HP7
10
HP8
11
TEST10
12
TEST11
13
TEST0
14
TEST1
15
TEST2
16
TEST3
17
—
Note: The mark
6
HP5
Contents
Status
Function
0
If VS is the vertical display start location,
1
0
1
0
7
Remarks
The vertical start location is
specified using the 8 bits from
VP7 to VP0.
VP7 to VP0 < 1416 are not
available.
VS = H ✕ ( Σ 2 VPn )
n
n=0
H: Cycle with the horizontal synchronizing pulse
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
8
HS = T ✕ ( Σ 2n HPn + 9 )
n=0
T: Cycle with the display clock
HOR
TV screen
VS
HS
1
0
1
0
1
0
The horizontal start location is
specified using the 9 bits from
HP8 to HP0.
HP8 to HP0 < 1916 are not
available.
If HS is the horizontal display start location,
VERT
DA
Character
displaying area
1 bit weights 1 clock.
Test mode (Must be cleared to 0.)
1
0
1
0
1
0
1
0
1
0
1
Must be cleared to 0.
__
around the status value means the reset status by the “L” level is input to AC pin.
MITSUBISHI MICROCOMPUTERS
M35060-XXXSP
SCREEN CHARACTER and PATTERN DISPLAY CONTROLLERS
(2) Address 2A916
DA
Register
0
HSZ0
1
HSZ1
2
HSZ2
3
HSZ3
4
HSZ4
5
HSZ5
6
HSZ6
7
HSZ7
8
HSZ8
9
HSZ9
A
HSZ10
B
HSZ11
C
HSZ12
D
HSZ13
E
HSZ14
F
HSZ15
10
HSZ16
11
BLINK0
12
BLINK1
13
BLINK2
14
BLINK3
15
—
16
—
17
—
Contents
Function
Status
0
1
0
1
Remarks
HSZx
Horizontal direction character size
0
1T/dot
1
2T/dot
0
1
0
1
Set to line 1 of display RAM
Set to line 2 of display RAM
T: Display clock
0
1
0
Set to line 5 of display RAM
Set to line 6 of display RAM
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
Set to line 7 of display RAM
Set to line 8 of display RAM
Set to line 9 of display RAM
Set to line 10 of display RAM
Set to line 11 of display RAM
Set to line 12 of display RAM
Set to line 13 of display RAM
Set to line 14 of display RAM
Set to line 15 of display RAM
1
0
1
1
0
1
Set to line 3 of display RAM
Set to line 4 of display RAM
1
0
1
0
1
0
Set to line 0 of display RAM
Set to line 16 of display RAM
BLINK0
BLINK1
0
1
0
Blinking OFF
Duty 50%
1
Duty 25%
Duty 75%
Cycle approximately 1 second.
0
Cycle approximately 0.5 second.
Normal blinking
1
Normal character, reversed character alternation display.
0
1
Must be cleared to 0.
Blinking duty ratio can be altered.
Blinking cycle can be altered.
Character is in flashing state.
Character is always displayed
(normal character, reversed character).
0
1
0
1
7
MITSUBISHI MICROCOMPUTERS
M35060-XXXSP
SCREEN CHARACTER and PATTERN DISPLAY CONTROLLERS
(3) Address 2AA16
8
DA
Register
0
VSZ0
1
VSZ1
2
VSZ2
3
VSZ3
4
VSZ4
5
VSZ5
6
VSZ6
7
VSZ7
8
VSZ8
9
VSZ9
A
VSZ10
B
VSZ11
C
VSZ12
D
VSZ13
E
VSZ14
F
VSZ15
10
VSZ16
11
HIDE
12
TEST20
13
EQP
14
TEST12
15
—
16
—
17
—
Status
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
Contents
Function
VSZx
Vertical direction character size
0
1H/dot
1
2H/dot
H: Horizontal synchronous pulse
Remarks
Set to line 0 of display RAM
Set to line 1 of display RAM
Set to line 2 of display RAM
Set to line 3 of display RAM
Set to line 4 of display RAM
Set to line 5 of display RAM
Set to line 6 of display RAM
Set to line 7 of display RAM
Set to line 8 of display RAM
Set to line 9 of display RAM
Set to line 10 of display RAM
Set to line 11 of display RAM
Set to line 12 of display RAM
Set to line 13 of display RAM
Set to line 14 of display RAM
Set to line 15 of display RAM
Set to line 16 of display RAM
SYRAM writting over
SYRAM writting over or character erasing
Test mode (Must be cleared to 0.)
It does not include equivalent pulse.
It includes equivalent pulse.
Test mode (Must be cleared to 0.)
Must be cleared to 0.
Decided by register LINER, G and
B or DAC bit of SYRAM.
MITSUBISHI MICROCOMPUTERS
M35060-XXXSP
SCREEN CHARACTER and PATTERN DISPLAY CONTROLLERS
(4) Address 2AB16
DA
Register
0
DSP0 00
1
DSP0 01
2
DSP0 02
3
DSP0 03
4
DSP0 04
5
DSP0 05
6
DSP0 06
7
DSP0 07
8
DSP0 08
9
DSP0 09
A
DSP0 10
B
DSP0 11
C
DSP0 12
D
DSP0 13
E
DSP0 14
F
DSP0 15
10
DSP0 16
Status
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
PHASE 0
1
0
12
PHASE 1
1
0
13
PHASE 2
1
14
TEST25
15
TEST26
16
—
17
—
DSP0XX
Remarks
Set to line 0 of display RAM
0
1
0
Character
Border
1
Matrix-outline
DSP1XX
Halftone
(Note)
Set by combination of DSP0XX (address 2AB16 and DSP1XX)
and DSP1XX (address 2AC16).
At internal synchronous mode (EX = 1), display monitor signal
area is all blanking signal (BLNK output) area.
0
1
0
1
0
1
Set to line 1 of display RAM
Set to line 2 of display RAM
Set to line 3 of display RAM
Set to line 4 of display RAM
Set to line 5 of display RAM
Note: For halftone display, it is necessary to input the external
Set to line 6 of display RAM
composite video signal to the CVIN terminal, and externally connect a 100 to 200 resistor in series.
However, the halftone display is possible only with superim- Set to line 7 of display RAM
posed displays.
Set to line 8 of display RAM
Set to line 9 of display RAM
Set to line 10 of display RAM
Set to line 11 of display RAM
Set to line 12 of display RAM
Set to line 13 of display RAM
Set to line 14 of display RAM
Set to line 15 of display RAM
0
1
0
11
Contents
Function
Set to line 16 of display RAM
PHASE PHASE PHASE
2
1
0
0
0
0
0
1
0
1
0
0
1
1
0
0
0
1
0
1
1
1
0
1
1
1
1
Raster color setting.
Color
SELCOR=0
Black
Red
Green
Yellow
Blue
Magenta
Cyan
White
SELCOR=1
Black
Red–2
Green–2
Yellow
Gray
Yellow–2
Cyan
White
Refer Fig 3, 4 about phase angle.
Test mode (Must be cleared to 0.)
Must be cleared to 0.
0
1
9
MITSUBISHI MICROCOMPUTERS
M35060-XXXSP
SCREEN CHARACTER and PATTERN DISPLAY CONTROLLERS
(5) Address 2AC16
DA
Register
0
DSP1 00
1
DSP1 01
2
DSP1 02
3
DSP1 03
4
DSP1 04
5
DSP1 05
6
DSP1 06
7
DSP1 07
8
DSP1 08
9
DSP1 09
A
DSP1 10
B
DSP1 11
C
DSP1 12
D
DSP1 13
E
DSP1 14
F
DSP1 15
10
DSP1 16
Status
0
1
0
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
LINER
0
LINEG
1
0
13
LINEB
1
10
14
TEST21
15
—
16
—
17
—
Set to line 0 of display RAM
0
1
0
Character
Border
1
Matrix-outline
Halftone
(Note)
Set by combination of DSP0XX (address 2AB16 and DSP1XX)
and DSP1XX (address 2AC16).
At internal synchronous mode (EX = 1), display monitor signal
area is all blanking signal (BLNK output) area.
0
1
0
1
0
1
0
1
Set to line 1 of display RAM
Set to line 2 of display RAM
Set to line 3 of display RAM
Set to line 4 of display RAM
Set to line 5 of display RAM
Note: For halftone display, it is necessary to input the external
composite video signal to the CVIN terminal, and externally con- Set to line 6 of display RAM
nect a 100 to 200 resistor in series.
However, the halftone display is possible only with superimSet to line 7 of display RAM
posed displays.
Set to line 8 of display RAM
Set to line 9 of display RAM
Set to line 10 of display RAM
Set to line 11 of display RAM
Set to line 12 of display RAM
Set to line 13 of display RAM
Set to line 14 of display RAM
Set to line 15 of display RAM
0
1
1
12
DSP0XX
Remarks
DSP1XX
1
0
1
0
11
Contents
Function
Set to line 16 of display RAM
LINE
B
0
0
0
0
1
1
1
1
LINE
G
0
0
1
1
0
0
1
1
LINE
R
0
1
0
1
0
1
0
1
Color
SELCOR=0
Black
Red
Green
Yellow
Blue
Magenta
Cyan
White
Test mode (Must be cleared to 0.)
Must be cleared to 0.
SELCOR=1
Black
Red–2
Green–2
Yellow
Gray
Yellow–2
Cyan
White
SYRAM color setting.
Color is decided by DAC bit
(SYEX) of SYRAM or HIDE
register.
Refer Fig. 3, 4 about phase angle.
MITSUBISHI MICROCOMPUTERS
M35060-XXXSP
SCREEN CHARACTER and PATTERN DISPLAY CONTROLLERS
(6) Address 2AD16
DA
Register
0
ERS0
1
ERS1
2
ERS2
3
ERS3
4
ERS4
5
ERS5
6
ERS6
7
ERS7
8
ERS8
9
ERS9
A
ERS10
B
ERS11
C
ERS12
D
ERS13
E
ERS14
F
ERS15
10
ERS16
11
SERS0
12
SERS1
13
SERS2
14
SERS3
15
TEST22
16
TEST23
17
—
Status
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
Contents
Function
Erase display RAM
ERSx
0
1
Remarks
Set to line 0 of display RAM
RAM erase
do erase
do not erase
It is unnecessary to reset these registers to “0”.
Multiple settings of ERSn is not allowed.
Set to line 1 of display RAM
Set to line 2 of display RAM
Set to line 3 of display RAM
Set to line 4 of display RAM
Set to line 5 of display RAM
Set to line 6 of display RAM
Set to line 7 of display RAM
Set to line 8 of display RAM
Set to line 9 of display RAM
Set to line 10 of display RAM
Set to line 11 of display RAM
Set to line 12 of display RAM
Set to line 13 of display RAM
Set to line 14 of display RAM
Set to line 15 of display RAM
Set to line 16 of display RAM
Erase SYRAM
SERSx
0
1
Set to SYRAM code 0016 to 0F16
SYRAM erase
do erase
do not erase
It is unnecessary to reset these registers to “0”.
Multiple settings of SERSn is not allowed.
Set to SYRAM code 1016 to 1F16
Set to SYRAM code 2016 to 2F16
Set to SYRAM code 3016 to 3E16
Test mode (Must be cleared to 0.)
Must be cleared to 0.
11
MITSUBISHI MICROCOMPUTERS
M35060-XXXSP
SCREEN CHARACTER and PATTERN DISPLAY CONTROLLERS
(7) Address 2AE16
DA
Register
0
SBIT0
1
SBIT1
2
SBIT2
3
SBIT3
4
SLIN0
5
SLIN1
6
SLIN2
7
SLIN3
8
SLIN4
9
SST0
A
SST1
B
SST2
C
SST3
D
SST4
E
SEND0
F
SEND1
10
SEND2
11
SEND3
12
SEND4
13
—
14
—
15
—
16
—
17
—
Contents
Function
Status
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
Set display start bit of scroll block:
3
SA = Σ 2 (SBITn)
n
n=0
Set display start line of scroll block:
4
SB = Σ 2 (SLINn)
n
n=0
Set start line of scroll block
(last line number of the fixed block 1):
4
SC = Σ 2n (SSTn)
n=0
Set start line of fixed block 2
(last line number of the scroll block):
4
SD = Σ 2 (SENDn)
n
n=0
Must be cleared to 0.
1
0
1
0
1
0
1
Note: When the scrolling on, set the ratio which will be SC < SB < SD.
12
Setting valid
SA = 0 to 12
invalid
SA = 13 to 15
Setting valid
SB = 0 to 16
invalid
SB = 17 to 31
Setting valid
SC = 0 to 15
invalid
SC = 16 to 31
When the scrolling on
setting valid SD = 2 to 17
invalid
SD = 18 to 31
When the scrolling off
set SD = 0
SD > SC + 2
1
0
1
0
1
0
Remarks
MITSUBISHI MICROCOMPUTERS
M35060-XXXSP
SCREEN CHARACTER and PATTERN DISPLAY CONTROLLERS
(8) Address 2AF16
Contents
DA
Register
0
PTC0
1
PTC1
2
PTC2
3
PTC3
4
PTC4
5
PTC5
6
PTD0
7
PTD1
8
PTD2
9
PTD3
A
PTD4
0
1
B
PTD5
0
1
C
SRAND0
D
SRAND1
E
SRAND2
Status
0
Port P0 output
1
YM output
0
Port P1 output
1
BLNK output
0
Port P2 output
1
0
B output
1
0
1
11
PC1
12
PC2
13
PC3
14
PC4
15
PC5
16
PC6
17
PC7
Port P3 output
G output
Select P3 pin
Port P4 output
Select P4 pin
CSYN output
When port output: 0 output, when YM output: negative polarity.
1
When port output: 1 output, when YM output: polarity.
When port output: 0 output, when BLNK output: negative polarity.
When port output: 1 output, when BLNK output: polarity.
When port output: 0 output, when B output: negative polarity.
0
1
0
1
0
1
0
1
0
1
1
PC0
Select P2 pin
1
0
ALL24
10
Select P1 pin
0
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
When port output: 1 output, when B output: polarity.
When port output: 0 output, when G output: negative polarity.
When port output: 1 output, when G output: polarity.
When port output: 0 output, when R output: negative polarity.
When port output: 1 output, when R output: polarity.
When port output: 0 output, when CSYN output: negative polarity.
When port output: 1 output, when CSYN output: polarity.
SRAND2
SRAND SRAND
0
1
1
0
Complete border = 1 dot Right and dot border = 1 dot
0
0
Complete border = 2 dot Right and dot border = 2 dot
0
1
Complete border = 3 dot Right and dot border = 3 dot
1
0
Complete border = 4 dot Right and dot border = 4 dot
1
1
Vertical direction is 1 dot only.
Blanking with all 40 characters in matrix-outline mode
Horizontal display period fully blanked with all characters in
matrix-outline size.
Display frequency fT control
7
Remarks
Select P0 pin
R output
Port P5 output
0
F
Function
Select P5 pin
Select data of P0 pin
Select data of P1 pin
Select data of P2 pin
Select data of P3 pin
Select data of P4 pin
Select data of P5 pin
Condition of border display is
changeable.
Horizontal display range can be
altered when all characters are in
matrix-outline size.
At external synchronous, set to 0.
Operation of character code FF16
becomes ineffective.
PC7 to PC0 < 3616,
PC7 to PC0 > C616 is not
available.
fT = fH ✕ { Σ (2 PCn) + 512 }
n
n=0
Note: At EX (address 2B016) = “0” (external synchronous), setting “1” of ALL24 register is not available.
Refer Fig. 2 about PTC0 to 5, PTD0 to 5.
13
MITSUBISHI MICROCOMPUTERS
M35060-XXXSP
SCREEN CHARACTER and PATTERN DISPLAY CONTROLLERS
(9) Address 2B016
DA
Register
0
EX
1
—
2
SELCOR
3
—
4
DSPON
5
DSPONV
6
—
7
BLK
8
SEPV0
Status
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
9
SEPV1
1
A
TEST15
B
TEST16
C
PALH
D
MPAL
E
PAL/NTSC
F
INT/NON
10
LEVEL0
11
LEVEL1
12
LEVEL2
13
TEST24
14
TEST17
15
TEST18
16
TEST19
17
—
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
Contents
Function
External synchronization
Internal synchronization
Set to “0”.
Normal
Mode of expansion
Must be cleared to 0.
Remarks
(Note)
Refer to Table 3, 4, 7 and 8.
Digital output display OFF
Digital output display ON
Composite video output display OFF
Composite video output display ON
Must be cleared to 0.
Matrix outline
Matrix outline + border
Only at register “DSP1XX”
= 1 (XX = 00 to 16) is available.
Method of sync separation from composite video.
SEPV1 SEPV0
0
0
0
1
1
0
1
1
Composite Sync Spearation Function
Separation is performed during (1) in vertical blanking period
Separation is performed during (2) in vertical blanking period 1
Separation is performed during (3) in vertical blanking period
Unavailable
2
1
3
Case (1) condition: vertical sync must repeat 2X
within (2) or (3); indicates this area.
Test mode (Must be cleared to 0.)
Interlace/noninterlace normal mode
Interlace/noninterlace expansion mode
Only at PAL and MPAL mode are
available.
PAL/NTSC
MPAL
Format
0
0
NTSC
0
1
M-PAL
1
0
PAL
1
1
unavailable
Interlace
Noninterlace
Composite video generation is off.
Composite video generation is on.
Display clock is on (oscillating).
Display clock is off (not oscillating).
Sync separation is disabled.
Sync separation is enabled.
Test mode (Must be cleared to 0.)
Refer to Table 5 and 6.
Must be cleared to 0.
Note: For internal synchronization, shut out (mute) the external video signal input to the CVIN terminal, outside the IC. This avoids external video signal leaks
inside the IC.
14
MITSUBISHI MICROCOMPUTERS
M35060-XXXSP
SCREEN CHARACTER and PATTERN DISPLAY CONTROLLERS
REGISTER CONSTRUCTION COMPOSITION
Table 3 Color and phase of NTSC, PAL (SELCOR = 0)
PHASE2 PHASE1 PHASE0
/
/
/
LINEB LINEG LINER
0
0
0
0
0
1
R (G, B, YM, BLNK, CSYN)
1
Color
NTSC
PAL
—
7 /16
—
± 7 /16
Black
Red
1
0
27 /16
±
5 /16
Green
0
1
1
0
1
0
/16
17 /16
± /16
15 /16
±
Yellow
Blue
1
0
1
11 /16
± 11 /16
Magenta
1
1
1
1
0
1
23 /16
—
9 /16
—
Cyan
White
0
±
Table 4 Color and phase of NTSC, PAL (SELCOR = 1)
0
0
1
1
1
1
1
1
0
1
0
1
—
/16
23 /16
—
Black
± 7 /16
5 /16
± /16
Red-2
Green-2
Yellow
—
± /16
Gray
Yellow-2
±
1
1
Color
±
0
Phase (rad)
NTSC
PAL
—
—
9 /16
Cyan
—
White
0
Polarity
Select
PTD
Fig. 2 Switching port output with R, G and B output
Table 5 Setting condition at LEVEL 0, 1 and 2
At display clock operates
At display clock stops
0
1
1
0
LEVEL1
7 /16
27 /16
/16
PTC
1
Phase (rad)
0
PHASE2 PHASE1 PHASE0
/
/
/
LINEB LINEG LINER
0
0
0
1
0
0
0
1
0
PTD
DSPON
DSPONV
CS pin
1
0
L
H
No character display at display clock
Table 6 Setting condition at LEVEL 0, 1 and 2 (at operation)
LEVEL0
LEVEL1
LEVEL2
Operation state
1
Stop state
0
0
1
1
0
Table 7 Video signal level (SELCOR = 0)
PAL
—
—
±4 /16
—
± 7 /16 ± 2 /16
5 /16 ± 2 /16
± /16 ± 2 /16
15 /16 ± 2 /16
± 11 /16 ± 2 /16
9 /16 ± 2 /16
—
±
±
Sync
Pedestal
Color Burst
Black
Red
Green
Yellow
Blue
Mazenta
Cyan
White
Phase (rad)
NTSC
—
—
0
—
7 /16 ± 2 /16
27 /16 ± 2 /16
/16 ± 2 /16
17 /16 ± 2 /16
11 /16 ± 2 /16
23 /16 ± 2 /16
—
±
Color name
Luminance level (V)
Chroma amplitude (vs. color burst)
Min.
1.3
Typ.
1.5
Max.
1.7
Min.
—
Typ.
—
Max.
—
1.9
1.9
2.1
2.3
2.7
3.1
2.0
2.5
2.9
3.1
2.1
2.1
2.3
2.5
2.9
3.3
2.2
2.7
3.1
3.3
2.3
2.3
2.5
2.7
3.1
3.5
2.4
2.9
3.3
3.5
—
—
—
1.5
1.4
1.0
1.0
1.4
1.5
—
—
1.0
—
3.0
2.8
2.0
2.0
2.8
3.0
—
—
—
—
4.5
4.2
3.0
3.0
4.2
4.5
—
15
MITSUBISHI MICROCOMPUTERS
M35060-XXXSP
SCREEN CHARACTER and PATTERN DISPLAY CONTROLLERS
Table 8 Video signal level (SELCOR = 1)
Phase (rad)
Color name
Luminance level (V)
Chroma amplitude (vs. color burst)
NTSC
PAL
Min.
Typ.
Max.
Min.
Typ.
Max.
Sync
—
—
Pedestal
Color Burst
—
0
—
±4 /16
1.3
1.9
1.5
2.1
1.7
2.3
—
—
—
—
—
—
1.9
2.1
2.3
—
1.0
—
Black
Red-2
—
7 /16 ± 2 /16
—
± 7 /16 ± 2 /16
2.1
2.6
2.3
2.8
2.5
3.0
—
1.5
—
2.0
—
3.0
Green-2
27 /16 ± 2 /16
±
5 /16 ± 2 /16
3.1
3.1
3.3
3.3
3.5
3.5
0.5
1.0
1.0
2.0
1.5
3.0
2.8
3.0
3.2
—
—
—
3.2
2.9
3.4
3.1
3.6
3.3
0.4
1.5
0.8
3.0
1.2
4.5
3.1
3.3
3.5
—
—
—
Yellow
Gray
/16 ± 2 /16
—
± /16 ± 2 /16
—
Yellow-2
/16 ± 2 /16
± /16 ± 2 /16
23 /16 ± 2 /16
—
±
Cyan
White
9 /16 ± 2 /16
—
Table 9 Display forms
DISPLAY FORMS
1. Blanking mode
Display mode
Display forms are shown in Table 9, display forms at each display
mode are shown in Fig. 3.
12 dots
12 dots
c
c
DSP1 XX
DSP0 XX
(Address 2AC16) (Address 2AB16)
BLNK output
Character
Border
Matrix-outline
0
0
1
0
1
0
Character size
Border size
All blanking
Halftone
1
1
Blanking OFF
14 dots
14 dots
Scanning
13
dots
BLNK
R,G,B
b
c
b
YM L
b
c
b
b
c
b
L
CVIDEO
(Internal sync)
b
c
b
b
a
a
c
b
b
c
b
(External sync)
a
(1)Character size
(2)Border size
Fig. 3 Display forms at each display mode
16
a
a
(3)Matrix-outline size
a
(4)Halftone size
a: External display
signal
b: Background color
c: Character color
MITSUBISHI MICROCOMPUTERS
M35060-XXXSP
SCREEN CHARACTER and PATTERN DISPLAY CONTROLLERS
For matrix and halftone, a character’s number of dots in the horizontal direction increases to 14.
Figure 4 shows a display example for a case where adjacent characters have different background colors and for character code FF16.
13 dots
12 dots
13 dots
11 dots
11 dots
14 dots
11 dots
40 characters
Character code FF 16
Fig. 4 Number of dots in the horizontal direction at matrix-outline or halftone
2. Border mode
In border mode, characters are displayed with borders. (Refer to
Table 9.) In matrix and halftone modes also, characters are displayed with borders if the BLK register (address 2B016) is set to 1.
Table 10 lists the types of borders.
Table 10 Bordering
SRAND1, 0
SRAND2
(Address 2AF 16)
00
01
10
11
1dot in horizontal
direction
2 dots in horizontal
direction
3 dots in horizontal
direction
4 dots in horizontal
direction
1 dot in horizontal
direction
2 dots in horizontal
direction
The zero
dot
0
1
3 dots in horizontal
direction
4 dots in horizontal
direction
Horizontal direction bordering is only 1 dot. When the character extends to the top line of the matrix, no border is left at the top, and when the
character extends to the bottom (12th) line of the matrix, no border is left at the bottom.
17
MITSUBISHI MICROCOMPUTERS
M35060-XXXSP
SCREEN CHARACTER and PATTERN DISPLAY CONTROLLERS
3. Setting matrix outline
The ALL24 register (address 2AF16) allows you to set a matrix
out-line. A matrix outline can be set for each line by using the
DSP1XX register (address 2AC16) .
However, this setting is inhibited if the EX register (address 2B016)
is 0 (external sync). An example of how you set a matrix outline is
shown in Figure 5.
Setting example of register
DSP1xx
DSP1 00
ALL24
“0”
to characters all matrix-outline
“0”
.....
DSP1 08
DSP1 09
DSP1 10
40 characters
“0”
“1”
“0”
.....
DSP1 16
ALL24
“1”
Horizontal display area all
matrix-outline
OSD display area
BR,BG,BB
Line 9
“0”
TV Screen
PHASE0,PHASE1,PHASE2
Note : It is not available to set when external synchronous(register EX = “0”)
Fig. 5 Setting example all matrix-outline area
4. Blinking mode
Two patterns blinking by register BLINK3 (address 2A916) or
BLINK bit of display RAM.
Blinking mode is shown in Table 11 (SYRAM do not blink).
Table 11
Blinking mode
Blinking mode
BLINK3
Table 12 Setting of duty ratio
at blinking OFF
Blinking
Normal
Normal character, reversed
character alternation display
Reverse
0
1
Use registers BLINK0, 1, and 2 (address 2A916) to set the duty
ratio and period that determines the blinking time. Tables 12 and
13 list the relationship between the register settings and the duty
ratio and period.
BLINK0
BLINK1
0
1
1
Blink OFF
Duty 50%
Duty 25%
Duty 75%
Table 13 Setting of cycle
BLINK2
0
1
18
0
Cycle
Approximately 1 second (Vertical sync
divided into 1/64)
Approximately 0.5 second (Vertical sync
divided into 1/32)
MITSUBISHI MICROCOMPUTERS
M35060-XXXSP
SCREEN CHARACTER and PATTERN DISPLAY CONTROLLERS
5. Scroll display mode
on the (SB)’th line.
The screen can be scrolled up or down by successively
incrementing or decrementing SA and SB.
Figure 6 shows examples of how the display is scrolled. The scroll
range in these examples contains 12 lines (second to the 13th lines).
However, the screen can display only 11 lines at a time, and the
remaining one line is handled as a dummy line and not displayed.
The scroll display mode is entered by setting registers SBIT0 to 3
(SA), SLIN0 to 4 (SB), SST0 to 4 (SC), and SEND0 to 4 (SD) (all
at address 2AE16). (Scroll is turned off when SD = 0.)
The screen is scrolled in the range from the (SC)’th line to the
(SD-1)’th line, and sections above and below this range are fixed.
The beginning line and beginning dot of scroll are the (SA)’th dot
Setting example 1
SA = 0
SB = 2
SC = 2
SD = 14
Setting example 2
SA = 3
SB = 5
SC = 2
SD = 14
Line number when
on screen display
0
1
Zero line
1st line
< fixed block >
2
3
4
5
6
7
8
9
10
11
12
2nd line (0 dot to 12 dots)
3rd
4th line
5th line
6th line
< Scrolling
7th line
8th line
9th line
10th line
11th line
12th line (0 dot to 12 dots)
13
14
15
14th line
15th line
16th line
block >
Dummy line
13th line (0 dot to 12 dots)
< fixed block >
Line number when
on screen display
0
1
Zero line
1st line
< fixed block >
5th line (3 dots to 12 dots)
2
3
4
5
6
7
8
9
10
11
12
6th line
7th line
8th line
9th line
10th line
11th line
12th line
13th line
2nd line
3rd line
13
14
15
14th line
15th line
16th line
< Scrolling
block >
Dummy line
5th line (0 dot to 2 dots)
or
4th line (3 dots to 12 dots)
4th line (0 dot to 2 dots)
< fixed block >
When displayed in order of SA = 0, 1, 2, and so on, the screen scrolls up. When displayed in order of SA = 12, 11, 10, and so on, the
screen scrolls down.
(1) To scroll the screen up, write the dummy line after you set the 0th dot in SA but before setting the 1st dot.
(2) To scroll the screen down, write the dummy line after you set the 0th dot in SA but before setting the 12th dot of the preceding line.
Fig. 6 Scrolling example
19
MITSUBISHI MICROCOMPUTERS
M35060-XXXSP
SCREEN CHARACTER and PATTERN DISPLAY CONTROLLERS
6. Character font
(1) Character ROM
Images are composed on a 12 ✕ 13 dot matrix, and characters
can be linked vertically and horizontally with other characters to
allow the display the continuous symbols.
Character code FF16 is fixed as blank, without a background.
(2) SYRAM
You can set characters for 63 letters per screen (SYRAM code
0016 to 3E16). Figure 9 shows an example of how to set.
Use display RAM’s SYC5 to 0 (0016 to 3E16) to specify SYRAM.
Note that SYRAM code 3F16 is fixed to a blank, so you cannot set
a character font to this code.
If you do not put SYRAM and a character together, use code
3F16.
.
13 dots
12 dots
Fig. 7 Character construction
13 dots
12 dots
Fig. 8 Example for displaying a continuous pattern
20
MITSUBISHI MICROCOMPUTERS
M35060-XXXSP
SCREEN CHARACTER and PATTERN DISPLAY CONTROLLERS
(ex) SYRAM code 0016 .................. Set character by setting data to address 30016 to 30C16
Address
30016
30116
30216
13 dots
30316
12 dots
30416
30516
30616
30716
30816
30916
30A16
30B16
30C16
17
0
0
0
0
0
0
0
0
0
0
0
0
0
…
…
…
…
…
…
…
…
…
…
…
…
…
…
Color expansion bit SYEX (set for each dot line)
The HIDE register (address 2AA16) becomes valid for
only the dot line where* = 1.
For details, refer to the next section, “(3) Compounding character ROM and SYRAM.”
DA
D C B A 9 8 7 6 5 4 3 2 1 0
0 * 0 0 0 0 0 0 0 0 0 0 0 0
0 * 0 0 0 0 0 0 0 0 0 0 0 1
0 * 0 0 0 0 0 0 0 0 0 0 1 1
0 * 0 0 0 0 0 0 0 0 0 1 1 1
0 * 0 0 0 0 0 0 0 0 1 1 1 1
0 * 0 0 0 0 0 0 0 1 1 1 1 1
0 * 0 0 0 0 0 0 1 1 1 1 1 1
0 * 0 0 0 0 0 1 1 1 1 1 1 1
0 * 0 0 0 0 1 1 1 1 1 1 1 1
0 * 0 0 0 1 1 1 1 1 1 1 1 1
0 * 0 0 1 1 1 1 1 1 1 1 1 1
0 * 0 1 1 1 1 1 1 1 1 1 1 1
0 * 1 1 1 1 1 1 1 1 1 1 1 1
13 dots
12 dots
1 bit: 1 dot of character
Fig. 9 Setting example of SYRAM
21
MITSUBISHI MICROCOMPUTERS
M35060-XXXSP
SCREEN CHARACTER and PATTERN DISPLAY CONTROLLERS
(3) Compounding character ROM and SYRAM
You can compound characters in character ROM with SYRAM.
The compounding method is determined by the SYEX color expansion bit and the HIDE register (address 2AA16).
For dot lines where SYEX = 0, the SYRAM color is set by the display RAM’s SR, SG, and SB irrespective of the HIDE register’s
content.
If the HIDE register’s content is 0, the SYRAM color for dot lines
where SYEX = 1 is set by the LINER, LINEG, and LINEB registers (address 2AC16).
If the HIDE register’s content is 1, the character ROM part of the
dot lines where SYEX = 1 is overwritten in HIDE mode with colors
set by the LINER, LINEG, and LINEB registers irrespective of the
ROM’s content and color. The color of the SYRAM part is set by
the display RAM’s SR, SG, and SB as in the case of dot lines
where SYEX = 0.
Figure 10 shows an example for each instance of compounding.
SYRAM
Character ROM
Compounding
Contents of
register HIDE
Ex. 1
Ex. 2
0 (normal mode)
SYEX
0
0
0
0
0
0
0
0
0
0
0
0
0
SYEX
1
1
1
1
1
0
0
0
0
0
0
0
0
1 (HIDE mode)
SR,
SG,
SB
LINER,
LINEG,
LINEB
SR,
SG,
SB
SYEX
0
0
0
0
0
0
0
0
0
0
0
0
0
SYEX
1
1
1
1
1
0
0
0
0
0
0
0
0
When HIDE = 1, the character ROM’s contents for dot lines where SYEX = 1 become invisible.
Fig. 10 Compounding example
22
SR,
SG,
SB
LINER,
LINEG,
LINEB
SR,
SG,
SB
4
3
2
1
825
824
823
822
Data (00116)
0
0
0
0
0
0
16
0
0
0
0
0
0
15
0
0
0
0
0
0
14
0
0
0
0
0
0
1
0
0
0
0
0
12
13
0
0
0
0
0
0
11
0
0
0
0
1
0
10
0
0
0
0
0
0
F
0
0
C
A
0
0
B
0
0
0
1
9
0
0
8
0
1
7
0
0
6
0
1
5
0
1
4
2
0
0
3
0
0
0
0
1
0
0
0
0 SYEX S01B S01A S019 S018 S017 S016 S015 S014 S013 S012 S011 S010
0 SYEX S00B S00A S009 S008 S007 S006 S005 S004 S003 S002 S001 S000
0
0
D
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0 SYEX S3EB S3EA S3E9 S3E8 S3E7 S3E6 S3E5 S3E4 S3E3 S3E2 S3E1 S3E0
0
0
0
0
0
E
0
0
0
0
0
0
0
0
0
0
PC7 PC6 PC5
0
Data (2AA16)
Data (2AB16)
Data (2AC16)
Data (2AD16)
Data (2AE16)
Data (2AF16)
Data (2B016)
1506
1507
1508
1509
1510
1511
1512
0
0
0
Data (2A916)
1505
Display ON
0
0
Data (2A816)
1504
0
0
0
0
0
0
0
0
SB SG SR
Data (2A716)
1503
Set registers
address
2A816 to 2AF16
SYC SYC SYC SYC SYC SYC
BB BG BR BLINK CB CG CR C7 C6 C5 C4 C3 C2 C1 C0
Set registers SB SG SR 5
4
3
2
1
0
address
SYC SYC SYC SYC SYC SYC
BB BG BR BLINK CB CG CR C7 C6 C5 C4 C3 C2 C1 C0
display RAM SB SG SR
5
4
3
2
1
0
00016 to 2A716
0
Address (00016)
Data (00016)
0
0
0
0
0
17
DA DA DA DA DA DA DA DA DA DA DA DA DA DA DA DA DA DA DA DA DA DA DA DA
Data (6EC16)
Set address
Set addresses
SYRAM
30016 to 6EC16
Data (30016)
Data (30116)
Display OFF
Address setting
Address (2B016)
Data (2B016)
Remarks
Address/data
Contents
~
0
0
0
0
1
0
1
1
0
0
0
HSZ
12
VSZ
12
DSP
012
DSP
112
ERS
12
SST
3
SRAND
0
0
HSZ
11
VSZ
11
DSP
011
DSP
111
ERS
11
SST
2
PTD
5
HSZ HSZ HSZ
8
10 9
VSZ VSZ VSZ
8
10 9
DSP DSP DSP
010 009 008
DSP DSP DSP
110 109 108
ERS ERS ERS
8
10 9
SST SST SLIN
0
4
1
PTD PTD PTD
3
2
4
SEPV
SEPV
0
1
0
BLK
HSZ
7
VSZ
7
DSP
007
DSP
107
ERS
7
SLIN
3
PTD
1
0
HSZ
6
VSZ
6
DSP
006
DSP
106
ERS
6
SLIN
2
PTD
0
1
HSZ
5
VSZ
5
DSP
005
DSP
105
ERS
5
SLIN
1
PTC
5
1
HSZ
4
VSZ
4
DSP
004
DSP
104
ERS
4
SLIN
0
PTC
4
HSZ HSZ
2
3
VSZ VSZ
2
3
DSP DSP
003 002
DSP DSP
103 102
ERS ERS
2
3
SBIT SBIT
2
3
PTC PTC
2
3
SEL
0
COR
0
HSZ
1
VSZ
1
DSP
001
DSP
101
ERS
1
SBIT
1
PTC
1
EX
HSZ
0
VSZ
0
DSP
000
DSP
100
ERS
0
SBIT
0
PTC
0
0 HP8 HP7 HP6 HP5 HP4 HP3 HP2 HP1 HP0 VP7 VP6 VP5 VP4 VP3 VP2 VP1 VP0
BLINK BLINK BLINK BLINK HSZ HSZ HSZ HSZ
3
2
1
0 16 15 14 13
VSZ VSZ VSZ VSZ
0 EQP 0 HIDE
16 15 14 13
PHASE PHASE PHASE DSP DSP DSP DSP
0
2
1
0 016 015 014 013
LINE LINE LINE DSP DSP DSP DSP
0
B G R 116 115 114 113
SERS SERS SERS ERS ERS ERS ERS
0
2
1
0 16 15 14 13
SEND SEND SEND SEND SEND SST
0
0
4
3
2
1
0
4
SRAND
SRAND
PC4 PC3 PC2 PC1 PC0 ALL24
2
1
0
SYC SYC SYC SYC SYC SYC
BB BG BR BLINK CB CG CR C7 C6 C5 C4 C3 C2 C1 C0
5
4
3
2
1
0
~
~
~
~
~
~
~
~
~
No.
MITSUBISHI MICROCOMPUTERS
M35060-XXXSP
SCREEN CHARACTER and PATTERN DISPLAY CONTROLLERS
EXAMPLE FOR DATA INPUT
Use an 8-bit parallel ✕ 3 serial input to set data in the display RAM,
display control register, and SYRAM. Table 14 lists an example of
how data is set.
Table 14 Data setting
23
MITSUBISHI MICROCOMPUTERS
M35060-XXXSP
SCREEN CHARACTER and PATTERN DISPLAY CONTROLLERS
SERIAL DATA INPUT TIMING
(1) The address consists of 8 bits ✕ 3.
(2) The data consists of 8 bits ✕ 3.
(3) The 8 bits ✕ 3 in the SCK after the CS signal has fallen are the
address, and for succeeding input data, the address is
incremented every 24 bits (8 bits ✕ 3). Refer to Fig.12 about detail for address increment.
CS
SCK
DA7 to DA0
(MSB) (LSB)
LSB
MSB
Address (8 bits ✕ 3)
Fig. 11 Serial input timing
24
LSB
MSB
Data N (8 bits ✕ 3)
LSB
MSB
Data N + 1(8 bits ✕ 3)
N=1,2,3............
MITSUBISHI MICROCOMPUTERS
M35060-XXXSP
SCREEN CHARACTER and PATTERN DISPLAY CONTROLLERS
address
00016
...
display RAM
..
2A716
2A816
*Jump to address 000 16
automatically
2B016
2B116
..
unused address area
2FF16
30016
...
30D16
.. ...
*Jump to address 310 16
automatically
register
SYRAM code 00 16
unused address area
31016
SYRAM code 01 16
31D16
..
*Jump to address 320 16
automatically
unused address area
32016
SYRAM code 02 16
... ..
*Jump to address 330 16
automatically
32D16
...
60016
unused address area
..
*Jump to address 6E0 16
automatically
unused address area
.......
33016
6E016
...
SYRAM code 3E 16
6ED16
...
*Jump to address 000 16
automatically
unused address area
FFF16
Following FFF 16 is not available
When entering data, note that although addresses are incremented every data entry (8 bits ✕ 3), if an address value falls in the unused
address area, it is automatically converted to the address value indicated by the arrow. When entering SYRAM data, for example, you
can set this data simply by setting address 30016 first and then entering data 30016 to 30C16 (SYRAM code 0016) and next data 31016 to
31C16 (SYRAM code 0116). The same applies for SYRAM code 0216 to 3E16.
Fig. 12 Address construction
25
26
Fig.13 M35060-XXXSP example of peripheral circuit
470
220
120
220
2.2k
47 µ
+
Note 1
1.50V
10k
+5.0V
Note 2 Set basic electric potential in
consideration of dynamic range
of the transistor.
Note 1 Clamp sync chip to 1.50V.
62
220 µ
+
+7.0V
+7.0V
Composite video
signal output
47 µ
+
Note 2
From microcomputer
External composite
video
signal input
+
11
10
9
8
100p
470
AD0
HOR
CVIN
LEBK
LECHA
CVIDEO
VSS
VDD1
AC
AD7
AD6
AD5
AD4
AD3
AD2
AD1
Note 6
16
15
14
13
100 µ 1 µ 0.01 µ 12
+
1µ
+
Note 5
7
6
5
4
3
2
1
VREF
LP1
VDD2
LP2
OSCOUT
OSCIN
TESTB
P0
P1
P2
P3
P4
P5
TESTA
SCK
CS
1.75V
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
1µ
680
Note 4
4700p
Note 3
4.434MHz
+
Note 3
100 µ 1 µ
+
0.01 µ
1k
Note 7
0.01 µ
+5.0V
470p
M-PAL: 3.576MHz
PAL:
NTSC: 3.580MHz
Note 7 Connect crystal vibrator.
Note 6 This is provisional value of
sync separation noise eliminate filter.
Note 5 Construct integral circuit by
built-in 30kΩ of AC pin and an
external condenser.
Attention to supply voltage
rise time about this CR constant.
Note 4 Set electric potential of VREF
to (Sync chip electric potential
+ 0.25) V= 1.75V.
Note 3 External loop filter constant is
provisional value.
MITSUBISHI MICROCOMPUTERS
M35060-XXXSP
SCREEN CHARACTER and PATTERN DISPLAY CONTROLLERS
M35060-XXXSP PERIPHERAL CIRCUIT
MITSUBISHI MICROCOMPUTERS
M35060-XXXSP
SCREEN CHARACTER and PATTERN DISPLAY CONTROLLERS
TIMING REQUIREMENTS (Ta = – 20°C to + 70°C, VDD = 5.00 ± 0.25V unless otherwise noted)
DATA INPUT
Symbol
Paramenter
SCK width
CS setup time
CS hold time
AD setup time
AD hold time
1 word hold time
tW (SCK)
tsu (CS)
th (CS)
tsu (AD)
th (AD)
th (SCK)
Limits
Typ.
—
—
—
—
—
—
Min.
200
200
2
200
200
2
Unit
Max.
—
—
—
—
—
—
ns
ns
ms
ns
ns
ms
tw(CS)
2 µs
(min.)
CS
tsu(CS)
tw(SCK)
tw(SCK)
th(CS)
SCK
tsu(AD)
th(AD)
AD0 to 7
CS
th(SCK)
more than
2 µs
th(SCK)
more than
2 µs
SCK
1
2
3
1
2
3
1
2
3
Fig. 14 Serial input timing requirements
27
MITSUBISHI MICROCOMPUTERS
M35060-XXXSP
SCREEN CHARACTER and PATTERN DISPLAY CONTROLLERS
PRECAUTIONS
1. Note for when starting of system
Before setting registers at the starting of system, be sure to reset the M35060-XXXSP by applying “L” level to the AC pin.
2.
When power supply noise is generated, the internal oscillator
circuit does not stabilize, whereby causing horizontal jitters
across the picture display. Therefore, connect a bypass capacitor between the power supply and GND.
3. Note for when throwing power supply into the M35060-XXXSP
When power to the M35060-XXXSP is activated, characters are
sometimes output without defining the internal display RAM,
composite RAM and register. Also, immediately after power is
turned ON, up until the oscillator circuit stabilizes, data is sometimes not set correctly in the register. Therefore, use the following start-up procedure.
(a) Throwing power supply into the M35060-XXXSP(AC pin = “ L ”)
(b) Auto-clear releasing (AC pin = “H”)
(c) 200 ms waiting state (stabilization period of internal oscillation
circuit) Data input is forbidden.
(d) Set register LEVELn
(e) Set register PAL/NTSC
(f) Set register PCn
(g) 20 ms waiting state (stabilization period of internal oscillation
circuit)
Data input is forbidden.
(h) Set other registers
(i) Set SYRAM
(j) Set display RAM
(k) Set register DSPON and register DSPONV to display ON
4. Precautions when resuming internal oscillation from the OFF
state.
The internal oscillator circuit stops oscillating when register
LEVEL = 1, DSPON = 0, DSPONV = 0 and CS terminal = H.
When resuming internal oscillation from the OFF state, up until
the oscillator circuit stabilizes, data is sometimes not set correctly in the register. Therefore, start oscillation as follows.
(a) CS pin = “H” (oscillation stop)
(b) CS pin = “L” (oscillation start)
(c) 20 ms waiting state (stabilization period of internal oscillation
circuit)
(d) Set register LEVEL 1 = 0
(e) Set other registers: SYRAM, display RAM
(f) Set register DSPON and register DSPONV to display ON
5. Note for oscillation
Make note of the fact that the internal oscillator circuit cannot
stabilize in the below situations.
(a)When the external composite video signal is discontinuous
(changing channels etc.)
(b) When change the setting of register PCn
28
(c) When change the setting of register LEVELn
When (a)~(c), set the display to OFF by registers DSPON and
DSPONV before change the setting. Other registers’ settings are
forbidden during 20ms after the setting.
6. When no external composite video signal is input (Without a signal, characters cannot be displayed by external synchronization.
Therefore, switch to internal synchronization.)
7. When signal level of the external composite video signal is extremely poor (With a weak electric field, character display is uncontrollable by external synchronization. Therefore, switch to
internal synchronization.)
8. When a crystal oscillator is connected to OSCIN (22-pin) or
OSCOUT (21-pin) (Talk with the manufacturer of the crystal oscillator you are using about matching it to this IC.)
MITSUBISHI MICROCOMPUTERS
M35060-XXXSP
SCREEN CHARACTER and PATTERN DISPLAY CONTROLLERS
ABSOLUTE MAXIMUM RATINGS (VDD = 5.00V, Ta = – 20°C to +70°C unless otherwise noted)
Symbol
VDD
VI
VO
Pd
Topr
Tstg
Conditions
Parameter
Ratings
With respect to VSS.
Supply voltage
Input voltage
Unit
V
– 0.3 to 6.0
VSS – 0.3 < VI < VDD +0.3
VSS < VO < VDD
Output voltage
Ta = 25°C
Power dissipation
Operating temperature
300
V
mW
°C
– 20 to 70
– 40 to 125
Storage temperature
V
°C
RECOMMENDED OPERATIONAL CONDITIONS (VDD = 5.00V, Ta = – 20°C to +70°C unless otherwise noted)
VDD
VIH
VIL
VCVIN
fOSCIN
Limits
Parameter
Symbol
Min.
4.75
0.8 ✕ VDD
Supply voltage
“H” level input voltage AC, CS, SCK, AD0 to AD7
“L” level input voltage AC, CS, SCK, AD0 to AD7
Composite video input supply voltage CVIN
Oscillation frequency for synchronous signal
0
—
—
Typ.
5.00
VDD
0
2Vp-p
3.580
4.434
3.576
Max.
Unit
5.25
VDD
V
V
0.2 ✕ VDD
—
V
V
—
MHz
ELECTRICAL CHARACTERISTICS (VDD = 5.00V, Ta = +25°C unless otherwise noted)
Symbol
VDD
IDD
VOH
VOL
RI
Parameter
Supply voltage
Supply current
“H” level output voltage P0 to P5
“L” level output voltage P0 to P5
Pull-up resistance AC
Test conditions
Ta = – 20°C to +70°C
VDD = 5.00V
VDD = 4.75, IOH = – 0.2mA
VDD = 4.75, IOL = 0.2mA
VDD = 5.00V
Min.
4.75
Limits
Typ.
5.00
Max.
5.25
—
3.75
—
10
30
—
—
30
60
—
0.4
100
Min.
Limits
Typ.
Max.
—
1.5
—
Unit
V
mV
V
V
kΩ
VIDEO SIGNAL INPUT CONDITIONS (VDD = 5V, Ta = – 20°C to +70°C)
Symbol
VIN-CU
Parameter
Composite video signal input clamp supply
voltage
Test conditions
Sync-chip supply voltage
Unit
V
29
MITSUBISHI MICROCOMPUTERS
M35060-XXXSP
SCREEN CHARACTER and PATTERN DISPLAY CONTROLLERS
NOTE FOR SUPPLYING POWER
(1) Timing of power supplying to AC pin
The internal circuit of M35060-XXXSP is reset when the level of
the auto clear input pin AC is “L”.
This pin is hysteresis input with the pull-up resistor. The timing
about power supplying of AC pin is shown in Figure 15.
tw is the interval after the supply voltage becomes 0.8 ✕ VDD or
more and before the supply voltage to the AC pin (VAC) becomes
0.2 ✕ VDD or more.
After supplying the power (VDD and VSS) to M35060-XXXSP, the
tW time must be reserved for 1 ms or more.
Before starting input from the microcomputer, the waiting time
(ts) must be reserved for 200 ms after the supply voltage to the
AC pin becomes 0.8 ✕ VDD or more.
(2) Timing of power supplying to VDD1 pin and VDD2 pin
The power need to supply to VDD1 and VDD2 at a time, though it
is separated perfectly between the VDD1 as the digital line and
the VDD2 as the analog line.
Voltage [V]
Data input is not available
VDD
Supply voltage
VAC
(AC pin input voltage)
0.8 ✕ VDD
0.2 ✕ VDD
tw
200ms
Time t [s]
Fig. 15 Timing of power supplying to AC pin
PRECAUTION FOR USE
Notes on noise and latch-up
Connect a capacitor (approx. 0.1µF) between pins VDD and VSS at
the shortest distance using relatively thick wire to prevent noise and
latcj up.
30
ROM ORDERING METHOD
Please submit the information described below when ordering Mask
ROM.
(1) ROM Order Confirmation Form ................................................ 1
(2) Data to be written into mask ROM ................................ EPROM
(three sets containing the identical data)
(3) Mark Specification Form ........................................................... 1
(4) Program for character font generating + froppy disk in which
character data is input.
MITSUBISHI MICROCOMPUTERS
M35060-XXXSP
SCREEN CHARACTER and PATTERN DISPLAY CONTROLLERS
STANDARD ROM TYPE: M35060-001SP
Character patterns are fixed to the contents of Figure 16 to 19.
M35060-001SP is a standard ROM type of M35060-XXXSP.
0016
0116
0216
0316
0416
0516
0616
0716
0816
0916
0A16
0B16
0C16
0D16
0E16
0F16
1016
1116
1216
1316
1416
1516
1616
1716
1816
1916
1A16
1B16
1C16
1D16
1E16
1F16
2016
2116
2216
2316
2416
2516
2616
2716
2816
2916
2A16
2B16
2C16
2D16
2E16
2F16
3016
3116
3216
3316
3416
3516
3616
3716
3816
3916
3A16
3B16
3C16
3D16
3E16
3F16
Fig. 16 M35060-001SP character patterns (1)
31
MITSUBISHI MICROCOMPUTERS
M35060-XXXSP
SCREEN CHARACTER and PATTERN DISPLAY CONTROLLERS
4016
4116
4216
4316
4416
4516
4616
4716
4816
4916
4A16
4B16
4C16
4D16
4E16
4F16
5016
5116
5216
5316
5416
5516
5616
5716
5816
5916
5A16
5B16
5C16
5D16
5E16
5F16
6016
6116
6216
6316
6416
6516
6616
6716
6816
6916
6A16
6B16
6C16
6D16
6E16
6F16
7016
7116
7216
7316
7416
7516
7616
7716
7816
7916
7A16
7B16
7C16
7D16
7E16
7F16
Fig. 17 M35060-001SP character patterns (2)
32
MITSUBISHI MICROCOMPUTERS
M35060-XXXSP
SCREEN CHARACTER and PATTERN DISPLAY CONTROLLERS
8016
8116
8216
8316
8416
8516
8616
8716
8816
8916
8A16
8B16
8C16
8D16
8E16
8F16
9016
9116
9216
9316
9416
9516
9616
9716
9816
9916
9A16
9B16
9C16
9D16
9E16
9F16
A016
A116
A216
A316
A416
A516
A616
A716
A816
A916
AA16
AB16
AC16
AD16
AE16
AF16
B016
B116
B216
B316
B416
B516
B616
B716
B816
B916
BA16
BB16
BC16
BD16
BE16
BF16
Fig. 18 M35060-001SP character patterns (3)
33
MITSUBISHI MICROCOMPUTERS
M35060-XXXSP
SCREEN CHARACTER and PATTERN DISPLAY CONTROLLERS
C016
C116
C216
C316
C416
C516
C616
C716
C816
C916
CA16
CB16
CC16
CD16
CE16
CF16
D016
D116
D216
D316
D416
D516
D616
D716
D816
D916
DA16
DB16
DC16
DD16
DE16
DF16
E016
E116
E216
E316
E416
E516
E616
E716
E816
E916
EA16
EB16
EC16
ED16
EE16
EF16
F016
F116
F216
F316
F416
F516
F616
F716
F816
F916
FA16
FB16
FC16
FD16
FE16
FF16 blank
Fig. 19 M35060-001SP character patterns (4)
34
MITSUBISHI MICROCOMPUTERS
M35060-XXXSP
SCREEN CHARACTER and PATTERN DISPLAY CONTROLLERS
STANDARD ROM TYPE: M35060-002SP
M35060-002SP is a standard ROM type of M35060-XXXSP.
Character patterns are fixed to the contents of Figure 20 to 23.
0016
0116
0216
0316
0416
0516
0616
0716
0816
0916
0A16
0B16
0C16
0D16
0E16
0F16
1016
1116
1216
1316
1416
1516
1616
1716
1816
1916
1A16
1B16
1C16
1D16
1E16
1F16
2016
2116
2216
2316
2416
2516
2616
2716
2816
2916
2A16
2B16
2C16
2D16
2E16
2F16
3016
3116
3216
3316
3416
3516
3616
3716
3816
3916
3A16
3B16
3C16
3D16
3E16
3F16
Fig. 20 M35060-002SP character patterns (1)
35
MITSUBISHI MICROCOMPUTERS
M35060-XXXSP
SCREEN CHARACTER and PATTERN DISPLAY CONTROLLERS
4016
4116
4216
4316
4416
4516
4616
4716
4816
4916
4A16
4B16
4C16
4D16
4E16
4F16
5016
5116
5216
5316
5416
5516
5616
5716
5816
5916
5A16
5B16
5C16
5D16
5E16
5F16
6016
6116
6216
6316
6416
6516
6616
6716
6816
6916
6A16
6B16
6C16
6D16
6E16
6F16
7016
7116
7216
7316
7416
7516
7616
7716
7816
7916
7A16
7B16
7C16
7D16
7E16
7F16
Fig. 21 M35060-002SP character patterns (2)
36
MITSUBISHI MICROCOMPUTERS
M35060-XXXSP
SCREEN CHARACTER and PATTERN DISPLAY CONTROLLERS
8016
8116
8216
8316
8416
8516
8616
8716
8816
8916
8A16
8B16
8C16
8D16
8E16
8F16
9016
9116
9216
9316
9416
9516
9616
9716
9816
9916
9A16
9B16
9C16
9D16
9E16
9F16
A016
A116
A216
A316
A416
A516
A616
A716
A816
A916
AA16
AB16
AC16
AD16
AE16
AF16
B016
B116
B216
B316
B416
B516
B616
B716
B816
B916
BA16
BB16
BC16
BD16
BE16
BF16
Fig. 22 M35060-002SP character patterns (3)
37
MITSUBISHI MICROCOMPUTERS
M35060-XXXSP
SCREEN CHARACTER and PATTERN DISPLAY CONTROLLERS
C016
C116
C216
C316
C416
C516
C616
C716
C816
C916
CA16
CB16
CC16
CD16
CE16
CF16
D016
D116
D216
D316
D416
D516
D616
D716
D816
D916
DA16
DB16
DC16
DD16
DE16
DF16
E016
E116
E216
E316
E416
E516
E616
E716
E816
E916
EA16
EB16
EC16
ED16
EE16
EF16
F016
F116
F216
F316
F416
F516
F616
F716
F816
F916
FA16
FB16
FC16
FD16
FE16
FF16 blank
Fig. 23 M35060-002SP character patterns (4)
38
MITSUBISHI MICROCOMPUTERS
M35060-XXXSP
SCREEN CHARACTER and PATTERN DISPLAY CONTROLLERS
PACKAGE OUTLINE
32P4B
39
MITSUBISHI MICROCOMPUTERS
M35060-XXXSP
SCREEN CHARACTER and PATTERN DISPLAY CONTROLLERS
Keep safety first in your circuit designs!
•
Mitsubishi Electric Corporation puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to
personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of non-flammable
material or (iii) prevention against any malfunction or mishap.
•
These materials are intended as a reference to assist our customers in the selection of the Mitsubishi semiconductor product best suited to the customer’s application; they do not convey any license under any intellectual property
rights, or any other rights, belonging to Mitsubishi Electric Corporation or a third party.
Mitsubishi Electric Corporation assumes no responsibility for any damage, or infringement of any third-party’s rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application examples
contained in these materials.
All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information on products at the time of publication of these materials, and are subject to change by
Mitsubishi Electric Corporation without notice due to product improvements or other reasons. It is therefore recommended that customers contact Mitsubishi Electric Corporation or an authorized Mitsubishi Semiconductor product
distributor for the latest product information before purchasing a product listed herein.
The information described here may contain technical inaccuracies or typographical errors. Mitsubishi Electric Corporation assumes no responsibility for any damage, liability, or other loss rising from these inaccuracies or errors.
Please also pay attention to information published by Mitsubishi Electric Corporation by various means, including the Mitsubishi Semiconductor home page (http://www.mitsubishichips.com).
When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms, please be sure to evaluate all information as a total system before making a final decision
on the applicability of the information and products. Mitsubishi Electric Corporation assumes no responsibility for any damage, liability or other loss resulting from the information contained herein.
Mitsubishi Electric Corporation semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake. Please contact Mitsubishi Electric
Corporation or an authorized Mitsubishi Semiconductor product distributor when considering the use of a product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical,
aerospace, nuclear, or undersea repeater use.
The prior written approval of Mitsubishi Electric Corporation is necessary to reprint or reproduce in whole or in part these materials.
If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved
destination.
Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited.
Please contact Mitsubishi Electric Corporation or an authorized Mitsubishi Semiconductor product distributor for further details on these materials or the products contained therein.
Notes regarding these materials
•
•
•
•
•
•
•
© 2001 MITSUBISHI ELECTRIC CORP.
New publication, effective Oct. 2001.
40
Specifications subject to change without notice.
REVISION DESCRIPTION LIST
Rev.
No.
M35060-XXXSP DATA SHEET
Rev.
date
Revision Description
1.0
First Edition
9804
1.1
• Deletes some Japanese font and create pdf file (some pages)
• P39 and P40 MARK SPECIFICATION FORM and PACKAGE OUTLINE are added
0007
1.2
Delete MARK SPECIFICATION FORM
• 1 FEATURES
0008
Error
Screen composition
.......... 40 characters
1.3
Correct
16 lines
Screen composition
.......... 40 characters
(At scrolling)
.......... 40 characters
17 lines
16 lines
P1 The following note is added
Note: Superimpose black and white display. (NTSC, PAL, M-PAL)
P35 Fig 20 M35060-002SP character patterns(1)
Address 0016, 0116 ........ 3E16, 3F16 are added
P36 Fig 21 M35060-002SP character patterns(2)
Address 4016, 4116 ........ 7E16, 7F16 are added
P37 Fig 22 M35060-002SP character patterns(3)
Address 8016, 8116 ........ BE16, BF16 are added
P38 Fig 23 M35060-002SP character patterns(4)
Address C016, C116 ........ FE16, FF16 are added
(1/1)
0110