RENESAS R8C32G

Preliminary Datasheet
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
RENESAS MCU
1.
R01DS0026EJ0010
Rev.0.10
Feb 08, 2011
Overview
1.1
Features
The R8C/32G Group, R8C/32H Group of single-chip MCUs incorporates the R8C CPU core, employing
sophisticated instructions for a high level of efficiency. With 1 Mbyte of address space, and it is capable of
executing instructions at high speed. In addition, the CPU core boasts a multiplier for high-speed operation
processing.
Power consumption is low, and the supported operating modes allow additional power control. These MCUs are
designed to maximize EMI/EMS performance.
Integration of many peripheral functions, including multifunction timer and serial interface, reduces the number of
system components.
The R8C/32G Group has data flash (1 KB × 4 blocks) with the background operation (BGO) function.
1.1.1
Applications
Automobiles and others
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
Page 1 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
1.1.2
1. Overview
Specifications
Tables 1.1 and 1.2 outline the Specifications for R8C/32G Group. Tables 1.3 and 1.4 outline the Specifications
for R8C/32H Group.
Table 1.1
Item
CPU
Specifications for R8C/32G Group (1)
Function
Central processing
unit
Memory
ROM, RAM, Data
flash
Power Supply Voltage detection
Voltage
circuit
Detection
I/O Ports
Programmable I/O
ports
Clock
Clock generation
circuits
Interrupts
Watchdog Timer
DTC (Data Transfer Controller)
Timer
Timer RA
Timer RB
Timer RC
Timer RD (1)
Specification
R8C CPU core
• Number of fundamental instructions: 89
• Minimum instruction execution time:
50 ns (f(XIN) = 20 MHz, VCC = 2.7 to 5.5 V)
• Multiplier: 16 bits × 16 bits → 32 bits
• Multiply-accumulate instruction: 16 bits × 16 bits + 32 bits → 32 bits
• Operation mode: Single-chip mode (address space: 1 Mbyte)
Refer to Table 1.5 Product List for R8C/32G Group.
• Power-on reset
• Voltage detection 3 (detection level of voltage detection 1 selectable)
• Input-only: 1 pin
• CMOS I/O ports: 15, selectable pull-up resistor
3 circuits: XIN clock oscillation circuit,
High-speed on-chip oscillator (with frequency adjustment function),
Low-speed on-chip oscillator
• Oscillation stop detection: XIN clock oscillation stop detection function
• Frequency divider circuit: Dividing selectable 1, 2, 4, 8, and 16
• Low power consumption modes:
Standard operating mode (high-speed clock, high-speed on-chip oscillator,
low-speed on-chip oscillator), wait mode, stop mode
• Number of interrupt vectors: 69
• External Interrupt: 7 (INT × 3, Key input × 4)
• Priority levels: 7 levels
• 14 bits × 1 (with prescaler)
• Reset start selectable
• Low-speed on-chip oscillator for watchdog timer selectable
• 1 channel
• Activation sources: 28
• Transfer modes: 2 (normal mode, repeat mode)
8 bits × 1 (with 8-bit prescaler)
Timer mode (period timer), pulse output mode (output level inverted every
period), event counter mode, pulse width measurement mode, pulse period
measurement mode
8 bits × 1 (with 8-bit prescaler)
Timer mode (period timer), programmable waveform generation mode (PWM
output), programmable one-shot generation mode, programmable wait oneshot generation mode
16 bits × 1 (with 4 capture/compare registers)
Timer mode (input capture function, output compare function), PWM mode
(output 3 pins), PWM2 mode (PWM output pin)
16 bits × 2 (with 4 capture/compare registers)
Timer mode (input capture function, output compare function), PWM mode
(output 6 pins), reset synchronous PWM mode (output three-phase
waveforms (6 pins), sawtooth wave modulation), complementary PWM mode
(output three-phase waveforms (6 pins), triangular wave modulation), PWM3
mode (PWM output 2 pins with fixed period)
Note:
1. Timer RD in these products does not support full-spec emulators. Use the on-chip debugging emulator for
debugging.
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
Page 2 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
Table 1.2
Item
Serial
Interface
1. Overview
Specifications for R8C/32G Group (2)
Function
UART0
UART2
Synchronous Serial
Communication Unit (SSU)
LIN Module
A/D Converter
Comparator B
Flash Memory
Operating Frequency/Supply
Voltage
Current consumption
Operating Ambient Temperature
Package
Specification
Clock synchronous serial I/O/UART × 1 channel
Clock synchronous serial I/O/UART, I2C mode (I2C-bus), IE mode (IEBus),
multiprocessor communication function
1
Hardware LIN: 1 (timer RA, UART0)
10-bit resolution × 4 channels, includes sample and hold function, with sweep
mode
2 circuits
• Programming and erasure voltage: VCC = 2.7 to 5.5 V
• Programming and erasure endurance: 10,000 times (data flash)
1,000 times (program ROM)
• Program security: ROM code protect, ID code check
• Debug functions: On-chip debug, on-board flash rewrite function
• Background operation (BGO) function
f(XIN) = 20 MHz (VCC = 2.7 to 5.5 V)
Typ. 7 mA (VCC = 5.0 V, f(XIN) = 20 MHz)
-40 to 85°C (J version)
-80 to 125°C (K version) (1)
20-pin SSOP
Package code: PLSP0020JB-A (previous code: 20P2F-A)
Note:
1. Specify the K version if K version functions are to be used.
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
Page 3 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
Table 1.3
Item
CPU
Memory
Power Supply
Voltage
Detection
I/O Ports
Clock
Specifications for R8C/32H Group (1)
Function
Central processing
unit
ROM, RAM
Voltage detection
circuit
Programmable I/O
ports
Clock generation
circuits
Interrupts
Watchdog Timer
DTC (Data Transfer Controller)
Timer
1. Overview
Timer RA
Timer RB
Timer RC
Timer RD (1)
Specification
R8C CPU core
• Number of fundamental instructions: 89
• Minimum instruction execution time:
50 ns (f(XIN) = 20 MHz, VCC = 2.7 to 5.5 V)
• Multiplier: 16 bits × 16 bits → 32 bits
• Multiply-accumulate instruction: 16 bits × 16 bits + 32 bits → 32 bits
• Operation mode: Single-chip mode (address space: 1 Mbyte)
Refer to Table 1.6 Product List for R8C/32H Group.
• Power-on reset
• Voltage detection 3 (detection level of voltage detection 1 selectable)
• Input-only: 1 pin
• CMOS I/O ports: 15, selectable pull-up resistor
3 circuits: XIN clock oscillation circuit,
High-speed on-chip oscillator (with frequency adjustment function),
Low-speed on-chip oscillator
• Oscillation stop detection: XIN clock oscillation stop detection function
• Frequency divider circuit: Dividing selectable 1, 2, 4, 8, and 16
• Low power consumption modes:
Standard operating mode (high-speed clock, high-speed on-chip oscillator,
low-speed on-chip oscillator), wait mode, stop mode
• Number of interrupt vectors: 69
• External Interrupt: 7 (INT × 3, Key input × 4)
• Priority levels: 7 levels
• 14 bits × 1 (with prescaler)
• Reset start selectable
• Low-speed on-chip oscillator for watchdog timer selectable
• 1 channel
• Activation sources: 28
• Transfer modes: 2 (normal mode, repeat mode)
8 bits × 1 (with 8-bit prescaler)
Timer mode (period timer), pulse output mode (output level inverted every
period), event counter mode, pulse width measurement mode, pulse period
measurement mode
8 bits × 1 (with 8-bit prescaler)
Timer mode (period timer), programmable waveform generation mode (PWM
output), programmable one-shot generation mode, programmable wait oneshot generation mode
16 bits × 1 (with 4 capture/compare registers)
Timer mode (input capture function, output compare function), PWM mode
(output 3 pins), PWM2 mode (PWM output pin)
16 bits × 2 (with 4 capture/compare registers)
Timer mode (input capture function, output compare function), PWM mode
(output 6 pins), reset synchronous PWM mode (output three-phase
waveforms (6 pins), sawtooth wave modulation), complementary PWM mode
(output three-phase waveforms (6 pins), triangular wave modulation), PWM3
mode (PWM output 2 pins with fixed period)
Note:
1. Timer RD in these products does not support full-spec emulators. Use the on-chip debugging emulator for
debugging.
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
Page 4 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
Table 1.4
Item
Serial
Interface
1. Overview
Specifications for R8C/32H Group (2)
Function
UART0
UART2
Synchronous Serial
Communication Unit (SSU)
LIN Module
A/D Converter
Comparator B
Flash Memory
Operating Frequency/Supply
Voltage
Current consumption
Operating Ambient Temperature
Package
Specification
Clock synchronous serial I/O/UART × 1 channel
Clock synchronous serial I/O/UART, I2C mode (I2C-bus), IE mode (IEBus),
multiprocessor communication function
1
Hardware LIN: 1 (timer RA, UART0)
10-bit resolution × 4 channels, includes sample and hold function, with sweep
mode
2 circuits
• Programming and erasure voltage: VCC = 2.7 to 5.5 V
• Programming and erasure endurance: 100 times (program ROM)
• Program security: ROM code protect, ID code check
• Debug functions: On-chip debug, on-board flash rewrite function
f(XIN) = 20 MHz (VCC = 2.7 to 5.5 V)
Typ. 7 mA (VCC = 5.0 V, f(XIN) = 20 MHz)
-40 to 85°C (J version)
-80 to 125°C (K version) (1)
20-pin SSOP
Package code: PLSP0020JB-A (previous code: 20P2F-A)
Note:
1. Specify the K version if K version functions are to be used.
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
Page 5 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
1.2
1. Overview
Product List
Table 1.5 lists Product List for R8C/32G Group and Figure 1.1 shows a Part Number, Memory Size, and Package of
R8C/32G Group. Table 1.6 lists Product List for R8C/32H Group and Figure 1.2 shows a Part Number, Memory
Size, and Package of R8C/32H Group.
Table 1.5
Product List for R8C/32G Group
Part No.
R5F21324GJSP (D)
R5F21326GJSP (D)
R5F21324GKSP (D)
R5F21332GKSP (D)
ROM Capacity
Program ROM
Data flash
16 Kbytes
1 Kbyte × 4
32 Kbytes
1 Kbyte × 4
16 Kbytes
1 Kbyte × 4
32 Kbytes
1 Kbyte × 4
Current of Feb 2011
RAM
Capacity
1.5 Kbytes
2.5 Kbytes
1.5 Kbytes
2.5 Kbytes
Package Type
PLSP0020JB-A
PLSP0020JB-A
PLSP0020JB-A
PLSP0020JB-A
Remarks
J version
K version
(D): Under development
Part No.
R 5 F 21 32 6 G J SP
Package type:
SP: PLSP0020JB-A (0.65 mm pin-pitch)
Classification
J: Operating ambient temperature -40°C to 85°C
K: Operating ambient temperature -40°C to 125°C
ROM capacity
4: 16 KB
6: 32 KB
Data Flash
G: Data Flash
H: None
R8C/32G Group
R8C/3x Series
Memory type
F: Flash memory
Renesas MCU
Renesas semiconductor
Figure 1.1
Part Number, Memory Size, and Package of R8C/32G Group
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
Page 6 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
Table 1.6
1. Overview
Product List for R8C/32H Group
Part No.
R5F21324HJSP (D)
R5F21326HJSP (D)
R5F21324HKSP (D)
R5F21326HKSP (D)
ROM Capacity
Program ROM
Data flash
16 Kbytes
1 Kbyte × 4
32 Kbytes
1 Kbyte × 4
16 Kbytes
1 Kbyte × 4
32 Kbytes
1 Kbyte × 4
Current of Feb 2011
RAM
Capacity
1.5 Kbytes
2.5 Kbytes
1.5 Kbytes
2.5 Kbytes
Package Type
PLSP0020JB-A
PLSP0020JB-A
PLSP0020JB-A
PLSP0020JB-A
Remarks
J version
K version
(D): Under development
Part No.
R 5 F 21 32 6 H J SP
Package type:
SP: PLSP0020JB-A (0.65 mm pin-pitch)
Classification
J: Operating ambient temperature -40°C to 85°C
K: Operating ambient temperature -40°C to 125°C
ROM capacity
4: 16 KB
6: 32 KB
Data Flash
G: Data Flash
H: None
R8C/32H Group
R8C/3x Series
Memory type
F: Flash memory
Renesas MCU
Renesas semiconductor
Figure 1.2
Part Number, Memory Size, and Package of R8C/32H Group
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
Page 7 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
1.3
1. Overview
Block Diagram
Figure 1.2 shows a Block Diagram.
I/O ports
8
4
Port P1
Port P3
3
1
Port P4
Peripheral functions
Timers
UART or
clock synchronous serial I/O
(8 bits × 2)
Timer RA (8 bits × 1)
Timer RB (8 bits × 1)
Timer RC (16 bits × 1)
Timer RD (16 bits × 2)
System clock generation
circuit
XIN-XOUT
High-speed on-chip oscillator
Low-speed on-chip oscillator
SSU
(8 bits × 1)
LIN module
Watchdog timer
(14 bits)
Low-speed on-chip oscillator
for watchdog timer
Comparator B
Voltage detection circuit
A/D converter
(10 bits × 4 channels)
DTC
Memory
R8C CPU core
R0H
R1H
R0L
R1L
R2
R3
SB
ISP
INTB
A0
A1
FB
ROM (1)
USP
RAM (2)
PC
FLG
Multiplier
Notes:
1. ROM size varies with MCU type.
2. RAM size varies with MCU type.
Figure 1.3
Block Diagram
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
Page 8 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
1.4
1. Overview
Pin Assignment
Figure 1.4 shows the Pin Assignment (Top View). Table 1.7 outline the Pin Name Information by Pin Number.
20
P3_4/SCS/TRCIOC/IVREF3/TRDIOB0
2
19
P3_3/INT3/(SSI)/CTS2/RTS2/TRCCLK/IVCMP3/TRDIOD0
RESET
3
18
P1_0/KI0/AN8/TRDIOA1
P4_7/XOUT
4
17
P1_1/KI1/AN9/TRCIOA/TRCTRG/TRDIOB1
VSS/AVSS
5
16
P4_2/VREF
P4_6/XIN
6
15
P1_2/KI2/AN10/TRCIOB/TRDIOC1
VCC/AVCC
7
14
P1_3/KI3/AN11/TRBO/TRDIOD1
MODE
8
P4_5/INT0/(RXD2/SCL2)/ADTRG
P1_7/(TRAIO)/INT1/IVCMP1
R8C/32G Group
R8C/32H Group
1
PLSP0020JB-A
(20P2F-A)
(top view)
P3_5/SSCK/TRCIOD/(CLK2)/TRDIOA0/TRDCLK
P3_7/TRAO/SSO/(RXD2/SCL2)/(TXD2/SDA2)/TRDIOC0
13
P1_4/TXD0
9
12
P1_5/RXD0/(TRAIO)/(INT1)
10
11
P1_6/CLK0/(SSI)/IVREF1
Notes:
1. Can be assigned to the pin in parentheses by a program.
2. Confirm the pin 1 position on the package by referring to the package dimensions.
Figure 1.4
Pin Assignment (Top View)
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
Page 9 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
Table 1.7
Pin
Number
Pin Name Information by Pin Number
Control Pin
Port
1
P3_5
2
P3_7
3
4
5
6
7
8
1. Overview
RESET
XOUT
VSS/AVSS
XIN
VCC/AVCC
Interrupt
I/O Pin Functions for Peripheral Modules
Serial
A/D Converter,
Timer
SSU
Interface
Comparator B
TRCIOD/TRDIOA0/
(CLK2)
SSCK
TRDCLK
TRAO/TRDIOC0
(RXD2/SCL2/ SSO
TXD2/SDA2)
P4_7
P4_6
MODE
(RXD2/SCL2)
ADTRG
CLK0
IVCMP1
IVREF1
9
P4_5
INT0
10
11
P1_7
P1_6
INT1
12
13
P1_5
P1_4
(INT1)
(TRAIO)
14
P1_3
KI3
TRBO(/TRDIOD1)
AN11
15
P1_2
KI2
(TRCIOB/
TRDIOC1)
AN10
16
P4_2
17
P1_1
KI1
TRCIOA/TRCTRG/
TRDIOB1
AN9
18
P1_0
KI0
TRDIOA1
AN8
19
P3_3
INT3
TRCCLK/TRDIOD0
20
P3_4
(TRAIO)
(SSI)
RXD0
TXD0
VREF
TRCIOC/TRDIOB0
CTS2/RTS2
(SSI)
IVCMP3
SCS
IVREF3
Note:
1. Can be assigned to the pin in parentheses by a program.
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
Page 10 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
1.5
1. Overview
Pin Functions
Tables 1.8 and 1.9 list Pin Functions.
Table 1.8
Pin Functions (1)
Item
Pin Name
I/O Type
Description
Power supply input
VCC, VSS
−
Apply 2.7 V to 5.5 V to the VCC pin. Apply 0 V to the VSS pin.
Analog power
supply input
AVCC, AVSS
−
Power supply for the A/D converter.
Connect a capacitor between AVCC and AVSS.
Reset input
RESET
I
Input “L” on this pin resets the MCU.
MODE
MODE
I
Connect this pin to VCC via a resistor.
XIN clock input
XIN
I
XIN clock output
XOUT
These pins are provided for XIN clock generation circuit I/O.
Connect a ceramic resonator or a crystal oscillator between
the XIN and XOUT pins (1). To use an external clock, input it
to the XOUT pin and leave the XIN pin open.
INT interrupt input
INT0 to INT1, INT3
I
INT interrupt input pins.
INT0 is timer RB, RC and RD input pin.
Key input interrupt
KI0 to KI3
I
Key input interrupt input pins
Timer RA
TRAIO
I/O
Timer RA I/O pin
TRAO
O
Timer RA output pin
Timer RB
TRBO
O
Timer RB output pin
Timer RC
TRCCLK
I
External clock input pin
TRCTRG
Timer RD
SSU
I
External trigger input pin
TRCIOA, TRCIOB,
TRCIOC, TRCIOD
I/O
Timer RC I/O pins
TRDIOA0, TRDIOA1,
TRDIOB0, TRDIOB1,
TRDIOC0, TRDIOC1,
TRDIOD0, TRDIOD1
I/O
Timer RD I/O pins
TRDCLK
Serial interface
I/O
I
External clock input pin
CLK0, CLK2
I/O
RXD0, RXD2
I
Serial data input pins
Transfer clock I/O pins
TXD0, TXD2
O
Serial data output pins
CTS2
I
Transmission control input pin
RTS2
O
Reception control output pin
SCL2
I/O
I2C mode clock I/O pin
SDA2
I/O
I2C mode data I/O pin
SSI
I/O
Data I/O pin
SCS
I/O
Chip-select signal I/O pin
SSCK
I/O
Clock I/O pin
SSO
I/O
Data I/O pin
I: Input
O: Output
I/O: Input and output
Note:
1. Refer to the oscillator manufacturer for oscillation characteristics.
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
Page 11 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
Table 1.9
1. Overview
Pin Functions (2)
Item
Pin Name
I/O Type
Description
Reference voltage
input
VREF
I
Reference voltage input pin to A/D converter
A/D converter
AN8 to AN11
I
Analog input pins to A/D converter
ADTRG
I
A/D external trigger input pin
IVCMP1, IVCMP3
I
Comparator B analog voltage input pins
I
Comparator B reference voltage input pins
Comparator B
IVREF1, IVREF3
I/O port
P1_0 to P1_7,
P3_3 to P3_5, P3_7,
P4_5 to P4_7
Input port
P4_2
I: Input
O: Output
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
I/O
I
CMOS I/O ports. Each port has an I/O select direction
register, allowing each pin in the port to be directed for input
or output individually.
Any port set to input can be set to use a pull-up resistor or not
by a program.
Input-only port
I/O: Input and output
Page 12 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
2.
2. Central Processing Unit (CPU)
Central Processing Unit (CPU)
Figure 2.1 shows the CPU Registers. The CPU contains 13 registers. R0, R1, R2, R3, A0, A1, and FB configure a
register bank. There are two sets of register bank.
b31
b15
R2
R3
b8b7
b0
R0H (high-order of R0) R0L (low-order of R0)
R1H (high-order of R1) R1L (low-order of R1)
Data registers (1)
R2
R3
A0
A1
FB
b19
b15
Address registers (1)
Frame base register (1)
b0
Interrupt table register
INTBL
INTBH
The 4 high order bits of INTB are INTBH and
the 16 low order bits of INTB are INTBL.
b19
b0
Program counter
PC
b15
b0
USP
User stack pointer
ISP
Interrupt stack pointer
SB
Static base register
b15
b0
FLG
b15
b8
IPL
b7
Flag register
b0
U I O B S Z D C
Carry flag
Debug flag
Zero flag
Sign flag
Register bank select flag
Overflow flag
Interrupt enable flag
Stack pointer select flag
Reserved bit
Processor interrupt priority level
Reserved bit
Note:
1. These registers comprise a register bank. There are two register banks.
Figure 2.1
CPU Registers
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
Page 13 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
2.1
2. Central Processing Unit (CPU)
Data Registers (R0, R1, R2, and R3)
R0 is a 16-bit register for transfer, arithmetic, and logic operations. The same applies to R1 to R3. R0 can be split
into high-order bits (R0H) and low-order bits (R0L) to be used separately as 8-bit data registers. R1H and R1L are
analogous to R0H and R0L. R2 can be combined with R0 and used as a 32-bit data register (R2R0). R3R1 is
analogous to R2R0.
2.2
Address Registers (A0 and A1)
A0 is a 16-bit register for address register indirect addressing and address register relative addressing. It is also
used for transfer, arithmetic, and logic operations. A1 is analogous to A0. A1 can be combined with A0 and as a 32bit address register (A1A0).
2.3
Frame Base Register (FB)
FB is a 16-bit register for FB relative addressing.
2.4
Interrupt Table Register (INTB)
INTB is a 20-bit register that indicates the starting address of an interrupt vector table.
2.5
Program Counter (PC)
PC is 20 bits wide and indicates the address of the next instruction to be executed.
2.6
User Stack Pointer (USP) and Interrupt Stack Pointer (ISP)
The stack pointers (SP), USP and ISP, are each 16 bits wide. The U flag of FLG is used to switch between
USP and ISP.
2.7
Static Base Register (SB)
SB is a 16-bit register for SB relative addressing.
2.8
Flag Register (FLG)
FLG is an 11-bit register indicating the CPU state.
2.8.1
Carry Flag (C)
The C flag retains carry, borrow, or shift-out bits that have been generated by the arithmetic and logic unit.
2.8.2
Debug Flag (D)
The D flag is for debugging only. Set it to 0.
2.8.3
Zero Flag (Z)
The Z flag is set to 1 when an arithmetic operation results in 0; otherwise to 0.
2.8.4
Sign Flag (S)
The S flag is set to 1 when an arithmetic operation results in a negative value; otherwise to 0.
2.8.5
Register Bank Select Flag (B)
Register bank 0 is selected when the B flag is 0. Register bank 1 is selected when this flag is set to 1.
2.8.6
Overflow Flag (O)
The O flag is set to 1 when an operation results in an overflow; otherwise to 0.
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
Page 14 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
2.8.7
2. Central Processing Unit (CPU)
Interrupt Enable Flag (I)
The I flag enables maskable interrupts.
Interrupts are disabled when the I flag is set to 0, and are enabled when the I flag is set to 1. The I flag is set to 0
when an interrupt request is acknowledged.
2.8.8
Stack Pointer Select Flag (U)
ISP is selected when the U flag is set to 0; USP is selected when the U flag is set to 1.
The U flag is set to 0 when a hardware interrupt request is acknowledged or the INT instruction of software
interrupt numbers 0 to 31 is executed.
2.8.9
Processor Interrupt Priority Level (IPL)
IPL is 3 bits wide and assigns processor interrupt priority levels from level 0 to level 7.
If a requested interrupt has higher priority than IPL, the interrupt is enabled.
2.8.10
Reserved Bit
If necessary, set to 0. When read, the content is undefined.
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
Page 15 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
3.
3. Memory
Memory
3.1
R8C/32G Group
Figure 3.1 is a Memory Map of R8C/32G Group. The R8C/32G Group has a 1-Mbyte address space from addresses
00000h to FFFFFh. For example, a 32-Kbyte internal ROM area is allocated addresses 08000h to 0FFFFh.
The fixed interrupt vector table is allocated addresses 0FFDCh to 0FFFFh. The starting address of each interrupt
routine is stored here.
The internal ROM (data flash) is allocated addresses 03000h to 03FFFh.
The internal RAM is allocated higher addresses, beginning with address 00400h. For example, a 2.5-Kbyte internal
RAM area is allocated addresses 00400h to 00DFFh. The internal RAM is used not only for data storage but also as
a stack area when a subroutine is called or when an interrupt request is acknowledged.
Special function registers (SFRs) are allocated addresses 00000h to 002FFh and 02C00h to 02FFFh. Peripheral
function control registers are allocated here. All unallocated spaces within the SFRs are reserved and cannot be
accessed by users.
00000h
002FFh
SFR
(Refer to 4. Special
Function Registers
(SFRs))
00400h
Internal RAM
0FFD8h
0XXXXh
02C00h
02FFFh
03000h
Reserved area
0FFDCh
SFR
(Refer to 4. Special Function
Registers (SFRs))
Undefined instruction
Overflow
BRK instruction
Address match
Single step
Internal ROM
(data flash) (1)
03FFFh
0YYYYh
Watchdog timer, oscillation stop detection, voltage monitor
Internal ROM
(program ROM)
0FFFFh
0FFFFh
Address break
(Reserved)
Reset
Internal ROM
(program ROM)
ZZZZZh
FFFFFh
Notes:
1. Data flash indicates block A (1 Kbyte), block B (1 Kbyte), block C (1 Kbyte), and block D (1 Kbyte).
2. The blank areas are reserved and cannot be accessed by users.
Internal ROM
Part Number
R5F21324GJSP, R5F21324GKSP
R5F21326GJSP, R5F21326GKSP
Figure 3.1
Internal RAM
Size
Address 0YYYYh
Address ZZZZZh
Size
Address 0XXXXh
16 Kbytes
32 Kbytes
0C000h
08000h
-
1.5 Kbytes
2.5 Kbytes
009FFh
00DFFh
Memory Map of R8C/32G Group
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
Page 16 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
3.2
3. Memory
R8C/32H Group
Figure 3.2 is a Memory Map of R8C/32H Group. The R8C/32H Group has a 1-Mbyte address space from addresses
00000h to FFFFFh. The internal ROM (program ROM) is allocated lower addresses, beginning with address
0FFFFh. For example, a 32-Kbyte internal ROM area is allocated addresses 08000h to 0FFFFh.
The fixed interrupt vector table is allocated addresses 0FFDCh to 0FFFFh. The starting address of each interrupt
routine is stored here.
The internal RAM is allocated higher addresses, beginning with address 00400h. For example, a 2.5-Kbyte internal
RAM area is allocated addresses 00400h to 00DFFh. The internal RAM is used not only for data storage but also as
a stack area when a subroutine is called or when an interrupt request is acknowledged.
Special function registers (SFRs) are allocated addresses 00000h to 002FFh and 02C00h to 02FFFh. Peripheral
function control registers are allocated here. All unallocated spaces within the SFRs are reserved and cannot be
accessed by users.
00000h
002FFh
SFR
(Refer to 4. Special
Function Registers
(SFRs))
00400h
Internal RAM
0FFD8h
0XXXXh
02C00h
02FFFh
03000h
Reserved area
0FFDCh
SFR
(Refer to 4. Special Function
Registers (SFRs))
Undefined instruction
Overflow
BRK instruction
Address match
Single step
Watchdog timer, oscillation stop detection, voltage monitor
0YYYYh
Internal ROM
(program ROM)
0FFFFh
0FFFFh
Address break
(Reserved)
Reset
Internal ROM
(program ROM)
ZZZZZh
FFFFFh
Note:
1. The blank areas are reserved and cannot be accessed by users.
Internal ROM
Part Number
R5F21324HJSP, R5F21324HKSP
R5F21326HJSP, R5F21326HKSP
Figure 3.2
Internal RAM
Size
Address 0YYYYh
Address ZZZZZh
Size
Address 0XXXXh
16 Kbytes
32 Kbytes
0C000h
08000h
−
−
1.5 Kbytes
2.5 Kbytes
009FFh
00DFFh
Memory Map of R8C/32H Group
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
Page 17 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
4.
4. Special Function Registers (SFRs)
Special Function Registers (SFRs)
An SFR (special function register) is a control register for a peripheral function. Tables 4.1 to 4.12 list the special
function registers and Table 4.13 lists the ID Code Areas and Option Function Select Area.
Table 4.1
Address
0000h
0001h
0002h
0003h
0004h
0005h
0006h
0007h
0008h
0009h
000Ah
000Bh
000Ch
000Dh
000Eh
000Fh
0010h
0011h
0012h
0013h
0014h
0015h
0016h
0017h
0018h
0019h
001Ah
001Bh
001Ch
001Dh
001Eh
001Fh
0020h
0021h
0022h
0023h
0024h
0025h
0026h
0027h
0028h
0029h
002Ah
002Bh
002Ch
002Dh
002Eh
002Fh
0030h
0031h
0032h
0033h
0034h
0035h
0036h
0037h
0038h
SFR Information (1) (1)
Register
Symbol
After Reset
Processor Mode Register 0
Processor Mode Register 1
System Clock Control Register 0
System Clock Control Register 1
Module Standby Control Register
System Clock Control Register 3
Protect Register
Reset Source Determination Register
Oscillation Stop Detection Register
Watchdog Timer Reset Register
Watchdog Timer Start Register
Watchdog Timer Control Register
PM0
PM1
CM0
CM1
MSTCR
CM3
PRCR
RSTFR
OCD
WDTR
WDTS
WDTC
00h
00h
00101000b
00100000b
00h
00h
00h
0XXXXXXXb (2)
00000100b
XXh
XXh
00111111b
High-Speed On-Chip Oscillator Control Register 7
FRA7
When shipping
Count Source Protection Mode Register
CSPR
00h
10000000b (3)
High-Speed On-Chip Oscillator Control Register 0
High-Speed On-Chip Oscillator Control Register 1
High-Speed On-Chip Oscillator Control Register 2
On-Chip Reference Voltage Control Register
FRA0
FRA1
FRA2
OCVREFCR
00h
When shipping
00h
00h
High-Speed On-Chip Oscillator Control Register 4
High-Speed On-Chip Oscillator Control Register 5
High-Speed On-Chip Oscillator Control Register 6
FRA4
FRA5
FRA6
When Shipping
When Shipping
When Shipping
High-Speed On-Chip Oscillator Control Register 3
Voltage Monitor Circuit Control Register
Voltage Monitor Circuit Edge Select Register
FRA3
CMPA
VCAC
When shipping
00h
00h
Voltage Detect Register 1
Voltage Detect Register 2
VCA1
VCA2
00001000b
00h (4)
00100000b (5)
Voltage Detection 1 Level Select Register
VD1LS
00000111b
Voltage Monitor 0 Circuit Control Register
VW0C
1100X010b (4)
1100X011b (5)
10001010b
0039h
Voltage Monitor 1 Circuit Control Register
VW1C
X: Undefined
Notes:
1. The blank areas are reserved and cannot be accessed by users.
2. The CWR bit in the RSTFR register is set to 0 after power-on and voltage monitor 0 reset. Hardware reset, software reset, or watchdog timer
reset does not affect this bit.
3. The CSPROINI bit in the OFS register is set to 0.
4. The LVDAS bit in the OFS register is set to 1.
5. The LVDAS bit in the OFS register is set to 0.
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
Page 18 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
Table 4.2
4. Special Function Registers (SFRs)
SFR Information (2) (1)
Address
Register
003Ah
Voltage Monitor 2 Circuit Control Register
003Bh
003Ch
003Dh
003Eh
003Fh
0040h
0041h
Flash Memory Ready Interrupt Control Register
0042h
0043h
0044h
0045h
0046h
0047h
Timer RC Interrupt Control Register
0048h
Timer RD0 Interrupt Control Register
0049h
Timer RD1 Interrupt Control Register
004Ah
004Bh
UART2 Transmit Interrupt Control Register
004Ch
UART2 Receive Interrupt Control Register
004Dh
Key Input Interrupt Control Register
004Eh
A/D Conversion Interrupt Control Register
004Fh
SSU Interrupt Control Register
0050h
0051h
UART0 Transmit Interrupt Control Register
0052h
UART0 Receive Interrupt Control Register
0053h
0054h
0055h
0056h
Timer RA Interrupt Control Register
0057h
0058h
Timer RB Interrupt Control Register
0059h
INT1 Interrupt Control Register
005Ah
INT3 Interrupt Control Register
005Bh
005Ch
005Dh
INT0 Interrupt Control Register
005Eh
UART2 Bus Collision Detection Interrupt Control Register
005Fh
0060h
0061h
0062h
0063h
0064h
0065h
0066h
0067h
0068h
0069h
006Ah
006Bh
006Ch
006Dh
006Eh
006Fh
0070h
0071h
0072h
Voltage Monitor 1 Interrupt Control Register
0073h
Voltage Monitor 2 Interrupt Control Register
0074h
0075h
0076h
0077h
0078h
0079h
007Ah
007Bh
007Ch
007Dh
007Eh
007Fh
X: Undefined
Note:
1. The blank areas are reserved and cannot be accessed by users.
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
VW2C
Symbol
After Reset
10000010b
FMRDYIC
XXXXX000b
TRCIC
TRD0IC
TRD1IC
XXXXX000b
XXXXX000b
XXXXX000b
S2TIC
S2RIC
KUPIC
ADIC
SSUIC
XXXXX000b
XXXXX000b
XXXXX000b
XXXXX000b
XXXXX000b
S0TIC
S0RIC
XXXXX000b
XXXXX000b
TRAIC
XXXXX000b
TRBIC
INT1IC
INT3IC
XXXXX000b
XX00X000b
XX00X000b
INT0IC
U2BCNIC
XX00X000b
XXXXX000b
VCMP1IC
VCMP2IC
XXXXX000b
XXXXX000b
Page 19 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
Table 4.3
4. Special Function Registers (SFRs)
SFR Information (3) (1)
Address
Register
0080h
DTC Activation Control Register
0081h
0082h
0083h
0084h
0085h
0086h
0087h
0088h
DTC Activation Enable Register 0
0089h
DTC Activation Enable Register 1
008Ah
DTC Activation Enable Register 2
008Bh
DTC Activation Enable Register 3
008Ch
DTC Activation Enable Register 4
008Dh
008Eh
DTC Activation Enable Register 6
008Fh
0090h
0091h
0092h
0093h
0094h
0095h
0096h
0097h
0098h
0099h
009Ah
009Bh
009Ch
009Dh
009Eh
009Fh
00A0h
UART0 Transmit/Receive Mode Register
00A1h
UART0 Bit Rate Register
00A2h
UART0 Transmit Buffer Register
00A3h
00A4h
UART0 Transmit/Receive Control Register 0
00A5h
UART0 Transmit/Receive Control Register 1
00A6h
UART0 Receive Buffer Register
00A7h
00A8h
UART2 Transmit/Receive Mode Register
00A9h
UART2 Bit Rate Register
00AAh
UART2 Transmit Buffer Register
00ABh
00ACh
UART2 Transmit/Receive Control Register 0
00ADh
UART2 Transmit/Receive Control Register 1
00AEh
UART2 Receive Buffer Register
00AFh
00B0h
UART2 Digital Filter Function Select Register
00B1h
00B2h
00B3h
00B4h
00B5h
00B6h
00B7h
00B8h
00B9h
00BAh
00BBh
UART2 Special Mode Register 5
00BCh
UART2 Special Mode Register 4
00BDh
UART2 Special Mode Register 3
00BEh
UART2 Special Mode Register 2
00BFh
UART2 Special Mode Register
X: Undefined
Note:
1. The blank areas are reserved and cannot be accessed by users.
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
Symbol
DTCTL
00h
DTCEN0
DTCEN1
DTCEN2
DTCEN3
DTCEN4
00h
00h
00h
00h
00h
DTCEN6
00h
U0MR
U0BRG
U0TB
URXDF
00h
XXh
XXh
XXh
00001000b
00000010b
XXh
XXh
00h
XXh
XXh
XXh
00001000b
00000010b
XXh
XXh
00h
U2SMR5
U2SMR4
U2SMR3
U2SMR2
U2SMR
00h
00h
000X0X0Xb
X0000000b
X0000000b
U0C0
U0C1
U0RB
U2MR
U2BRG
U2TB
U2C0
U2C1
U2RB
After Reset
Page 20 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
Table 4.4
4. Special Function Registers (SFRs)
SFR Information (4) (1)
Address
Register
00C0h
A/D Register 0
00C1h
00C2h
A/D Register 1
00C3h
00C4h
A/D Register 2
00C5h
00C6h
A/D Register 3
00C7h
00C8h
A/D Register 4
00C9h
00CAh
A/D Register 5
00CBh
00CCh
A/D Register 6
00CDh
00CEh
A/D Register 7
00CFh
00D0h
00D1h
00D2h
00D3h
00D4h
A/D Mode Register
00D5h
A/D Input Select Register
00D6h
A/D Control Register 0
00D7h
A/D Control Register 1
00D8h
00D9h
00DAh
00DBh
00DCh
00DDh
00DEh
00DFh
00E0h
00E1h
Port P1 Register
00E2h
00E3h
Port P1 Direction Register
00E4h
00E5h
Port P3 Register
00E6h
00E7h
Port P3 Direction Register
00E8h
Port P4 Register
00E9h
00EAh
Port P4 Direction Register
00EBh
00ECh
00EDh
00EEh
00EFh
00F0h
00F1h
00F2h
00F3h
00F4h
00F5h
00F6h
00F7h
00F8h
00F9h
00FAh
00FBh
00FCh
00FDh
00FEh
00FFh
X: Undefined
Note:
1. The blank areas are reserved and cannot be accessed by users.
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
Symbol
AD0
AD1
AD2
AD3
AD4
AD5
AD6
AD7
After Reset
XXh
000000XXb
XXh
000000XXb
XXh
000000XXb
XXh
000000XXb
XXh
000000XXb
XXh
000000XXb
XXh
000000XXb
XXh
000000XXb
ADMOD
ADINSEL
ADCON0
ADCON1
00h
11000000b
00h
00h
P1
XXh
PD1
00h
P3
XXh
PD3
P4
00h
XXh
PD4
00h
Page 21 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
Table 4.5
4. Special Function Registers (SFRs)
SFR Information (5) (1)
Address
Register
0100h
Timer RA Control Register
0101h
Timer RA I/O Control Register
0102h
Timer RA Mode Register
0103h
Timer RA Prescaler Register
0104h
Timer RA Register
0105h
LIN Control Register 2
0106h
LIN Control Register
0107h
LIN Status Register
0108h
Timer RB Control Register
0109h
Timer RB One-Shot Control Register
010Ah
Timer RB I/O Control Register
010Bh
Timer RB Mode Register
010Ch
Timer RB Prescaler Register
010Dh
Timer RB Secondary Register
010Eh
Timer RB Primary Register
010Fh
0110h
0111h
0112h
0113h
0114h
0115h
0116h
0117h
0118h
0119h
011Ah
011Bh
011Ch
011Dh
011Eh
011Fh
0120h
Timer RC Mode Register
0121h
Timer RC Control Register 1
0122h
Timer RC Interrupt Enable Register
0123h
Timer RC Status Register
0124h
Timer RC I/O Control Register 0
0125h
Timer RC I/O Control Register 1
0126h
Timer RC Counter
0127h
0128h
Timer RC General Register A
0129h
012Ah
Timer RC General Register B
012Bh
012Ch
Timer RC General Register C
012Dh
012Eh
Timer RC General Register D
012Fh
0130h
Timer RC Control Register 2
0131h
Timer RC Digital Filter Function Select Register
0132h
Timer RC Output Master Enable Register
0133h
Timer RC Trigger Control Register
0134h
0135h
0136h
Timer RD Trigger Control Register
0137h
Timer RD Start Register
0138h
Timer RD Mode Register
0139h
Timer RD PWM Mode Register
013Ah
Timer RD Function Control Register
013Bh
Timer RD Output Master Enable Register 1
013Ch
Timer RD Output Master Enable Register 2
013Dh
Timer RD Output Control Register
013Eh
Timer RD Digital Filter Function Select Register 0
013Fh
Timer RD Digital Filter Function Select Register 1
Note:
1. The blank areas are reserved and cannot be accessed by users.
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
Symbol
TRACR
TRAIOC
TRAMR
TRAPRE
TRA
LINCR2
LINCR
LINST
TRBCR
TRBOCR
TRBIOC
TRBMR
TRBPRE
TRBSC
TRBPR
TRCMR
TRCCR1
TRCIER
TRCSR
TRCIOR0
TRCIOR1
TRC
After Reset
00h
00h
00h
FFh
FFh
00h
00h
00h
00h
00h
00h
00h
FFh
FFh
FFh
TRCCR2
TRCDF
TRCOER
TRCADCR
01001000b
00h
01110000b
01110000b
10001000b
10001000b
00h
00h
FFh
FFh
FFh
FFh
FFh
FFh
FFh
FFh
00011000b
00h
01111111b
00h
TRDADCR
TRDSTR
TRDMR
TRDPMR
TRDFCR
TRDOER1
TRDOER2
TRDOCR
TRDDF0
TRDDF1
00h
11111100b
00001110b
10001000b
10000000b
FFh
01111111b
00h
00h
00h
TRCGRA
TRCGRB
TRCGRC
TRCGRD
Page 22 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
Table 4.6
4. Special Function Registers (SFRs)
SFR Information (6) (1)
Address
Register
0140h
Timer RD Control Register 0
0141h
Timer RD I/O Control Register A0
0142h
Timer RD I/O Control Register C0
0143h
Timer RD Status Register 0
0144h
Timer RD Interrupt Enable Register 0
0145h
Timer RD PWM Mode Output Level Control Register 0
0146h
Timer RD Counter 0
0147h
0148h
Timer RD General Register A0
0149h
014Ah
Timer RD General Register B0
014Bh
014Ch
Timer RD General Register C0
014Dh
014Eh
Timer RD General Register D0
014Fh
0150h
Timer RD Control Register 1
0151h
Timer RD I/O Control Register A1
0152h
Timer RD I/O Control Register C1
0153h
Timer RD Status Register 1
0154h
Timer RD Interrupt Enable Register 1
0155h
Timer RD PWM Mode Output Level Control Register 1
0156h
Timer RD Counter 1
0157h
0158h
Timer RD General Register A1
0159h
015Ah
Timer RD General Register B1
015Bh
015Ch
Timer RD General Register C1
015Dh
015Eh
Timer RD General Register D1
015Fh
0160h
0161h
0162h
0163h
0164h
0165h
0166h
0167h
0168h
0169h
016Ah
016Bh
016Ch
016Dh
016Eh
016Fh
0170h
0171h
0172h
0173h
0174h
0175h
0176h
0177h
0178h
0179h
017Ah
017Bh
017Ch
017Dh
017Eh
017Fh
X: Undefined
Note:
1. The blank areas are reserved and cannot be accessed by users.
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
Symbol
TRDCR0
TRDIORA0
TRDIORC0
TRDSR0
TRDIER0
TRDPOCR0
TRD0
TRDGRA0
TRDGRB0
TRDGRC0
TRDGRD0
TRDCR1
TRDIORA1
TRDIORC1
TRDSR1
TRDIER1
TRDPOCR1
TRD1
TRDGRA1
TRDGRB1
TRDGRC1
TRDGRD1
After Reset
00h
10001000b
10001000b
11100000b
11100000b
11111000b
00h
00h
FFh
FFh
FFh
FFh
FFh
FFh
FFh
FFh
00h
10001000b
10001000b
11000000b
11100000b
11111000b
00h
00h
FFh
FFh
FFh
FFh
FFh
FFh
FFh
FFh
Page 23 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
Table 4.7
4. Special Function Registers (SFRs)
SFR Information (7) (1)
Address
Register
0180h
Timer RA Pin Select Register
0181h
Timer RB/RC Pin Select Register
0182h
Timer RC Pin Select Register 0
0183h
Timer RC Pin Select Register 1
0184h
Timer RD Pin Select Register 0
0185h
Timer RD Pin Select Register 1
0186h
0187h
0188h
UART0 Pin Select Register
0189h
018Ah
UART2 Pin Select Register 0
018Bh
UART2 Pin Select Register 1
018Ch
SSU Pin Select Register
018Dh
018Eh
INT Interrupt Input Pin Select Register
018Fh
I/O Function Pin Select Register
0190h
0191h
0192h
0193h
SS Bit Counter Register
0194h
SS Transmit Data Register L
0195h
SS Transmit Data Register H
0196h
SS Receive Data Register L
0197h
SS Receive Data Register H
0198h
SS Control Register H
0199h
SS Control Register L
019Ah
SS Mode Register
019Bh
SS Enable Register
019Ch
SS Status Register
019Dh
SS Mode Register 2
019Eh
019Fh
01A0h
01A1h
01A2h
01A3h
01A4h
01A5h
01A6h
01A7h
01A8h
01A9h
01AAh
01ABh
01ACh
01ADh
01AEh
01AFh
01B0h
01B1h
01B2h
Flash Memory Status Register
01B3h
01B4h
Flash Memory Control Register 0
01B5h
Flash Memory Control Register 1
01B6h
Flash Memory Control Register 2
01B7h
01B8h
01B9h
01BAh
01BBh
01BCh
01BDh
01BEh
01BFh
X: Undefined
Note:
1. The blank areas are reserved and cannot be accessed by users.
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
Symbol
TRASR
TRBRCSR
TRCPSR0
TRCPSR1
TRDPSR0
TRDPSR1
00h
00h
00h
00h
00h
00h
After Reset
U0SR
00h
U2SR0
U2SR1
SSUIICSR
00h
00h
00h
INTSR
PINSR
00h
00h
SSBR
SSTDR
SSTDRH
SSRDR
SSRDRH
SSCRH
SSCRL
SSMR
SSER
SSSR
SSMR2
11111000b
FFh
FFh
FFh
FFh
00h
01111101b
00010000b
00h
00h
00h
FST
10000X00b
FMR0
FMR1
FMR2
00h
00h
00h
Page 24 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
Table 4.8
4. Special Function Registers (SFRs)
SFR Information (8) (1)
Address
Register
01C0h
Address Match Interrupt Register 0
01C1h
01C2h
01C3h
Address Match Interrupt Enable Register 0
01C4h
Address Match Interrupt Register 1
01C5h
01C6h
01C7h
Address Match Interrupt Enable Register 1
01C8h
01C9h
01CAh
01CBh
01CCh
01CDh
01CEh
01CFh
01D0h
01D1h
01D2h
01D3h
01D4h
01D5h
01D6h
01D7h
01D8h
01D9h
01DAh
01DBh
01DCh
01DDh
01DEh
01DFh
01E0h
Pull-Up Control Register 0
01E1h
Pull-Up Control Register 1
01E2h
01E3h
01E4h
01E5h
01E6h
01E7h
01E8h
01E9h
01EAh
01EBh
01ECh
01EDh
01EEh
01EFh
01F0h
01F1h
01F2h
01F3h
01F4h
01F5h
Input Threshold Control Register 0
01F6h
Input Threshold Control Register 1
01F7h
01F8h
Comparator B Control Register 0
01F9h
01FAh
External Input Enable Register 0
01FBh
01FCh
INT Input Filter Select Register 0
01FDh
01FEh
Key Input Enable Register 0
01FFh
X: Undefined
Note:
1. The blank areas are reserved and cannot be accessed by users.
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
Symbol
RMAD0
AIER1
After Reset
XXh
XXh
0000XXXXb
00h
XXh
XXh
0000XXXXb
00h
PUR0
PUR1
00h
00h
VLT0
VLT1
00h
00h
INTCMP
00h
INTEN
00h
INTF
00h
KIEN
00h
AIER0
RMAD1
Page 25 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
Table 4.9
4. Special Function Registers (SFRs)
SFR Information (9) (1)
Address
Register
2C00h
DTC Transfer Vector Area
2C01h
DTC Transfer Vector Area
2C02h
DTC Transfer Vector Area
2C03h
DTC Transfer Vector Area
2C04h
DTC Transfer Vector Area
2C05h
DTC Transfer Vector Area
2C06h
DTC Transfer Vector Area
2C07h
DTC Transfer Vector Area
2C08h
DTC Transfer Vector Area
2C09h
DTC Transfer Vector Area
2C0Ah
DTC Transfer Vector Area
:
DTC Transfer Vector Area
:
DTC Transfer Vector Area
2C3Ah
DTC Transfer Vector Area
2C3Bh
DTC Transfer Vector Area
2C3Ch
DTC Transfer Vector Area
2C3Dh
DTC Transfer Vector Area
2C3Eh
DTC Transfer Vector Area
2C3Fh
DTC Transfer Vector Area
2C40h
DTC Control Data 0
2C41h
2C42h
2C43h
2C44h
2C45h
2C46h
2C47h
2C48h
DTC Control Data 1
2C49h
2C4Ah
2C4Bh
2C4Ch
2C4Dh
2C4Eh
2C4Fh
2C50h
DTC Control Data 2
2C51h
2C52h
2C53h
2C54h
2C55h
2C56h
2C57h
2C58h
DTC Control Data 3
2C59h
2C5Ah
2C5Bh
2C5Ch
2C5Dh
2C5Eh
2C5Fh
2C60h
DTC Control Data 4
2C61h
2C62h
2C63h
2C64h
2C65h
2C66h
2C67h
2C68h
DTC Control Data 5
2C69h
2C6Ah
2C6Bh
2C6Ch
2C6Dh
2C6Eh
2C6Fh
X: Undefined
Note:
1. The blank areas are reserved and cannot be accessed by users.
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
Symbol
DTCD0
DTCD1
DTCD2
DTCD3
DTCD4
DTCD5
After Reset
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
Page 26 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
Table 4.10
4. Special Function Registers (SFRs)
SFR Information (10) (1)
Address
Register
2C70h
DTC Control Data 6
2C71h
2C72h
2C73h
2C74h
2C75h
2C76h
2C77h
2C78h
DTC Control Data 7
2C79h
2C7Ah
2C7Bh
2C7Ch
2C7Dh
2C7Eh
2C7Fh
2C80h
DTC Control Data 8
2C81h
2C82h
2C83h
2C84h
2C85h
2C86h
2C87h
2C88h
DTC Control Data 9
2C89h
2C8Ah
2C8Bh
2C8Ch
2C8Dh
2C8Eh
2C8Fh
2C90h
DTC Control Data 10
2C91h
2C92h
2C93h
2C94h
2C95h
2C96h
2C97h
2C98h
DTC Control Data 11
2C99h
2C9Ah
2C9Bh
2C9Ch
2C9Dh
2C9Eh
2C9Fh
2CA0h
DTC Control Data 12
2CA1h
2CA2h
2CA3h
2CA4h
2CA5h
2CA6h
2CA7h
2CA8h
DTC Control Data 13
2CA9h
2CAAh
2CABh
2CACh
2CADh
2CAEh
2CAFh
X: Undefined
Note:
1. The blank areas are reserved and cannot be accessed by users.
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
Symbol
DTCD6
DTCD7
DTCD8
DTCD9
DTCD10
DTCD11
DTCD12
DTCD13
After Reset
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
Page 27 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
Table 4.11
4. Special Function Registers (SFRs)
SFR Information (11) (1)
Address
Register
2CB0h
DTC Control Data 14
2CB1h
2CB2h
2CB3h
2CB4h
2CB5h
2CB6h
2CB7h
2CB8h
DTC Control Data 15
2CB9h
2CBAh
2CBBh
2CBCh
2CBDh
2CBEh
2CBFh
2CC0h
DTC Control Data 16
2CC1h
2CC2h
2CC3h
2CC4h
2CC5h
2CC6h
2CC7h
2CC8h
DTC Control Data 17
2CC9h
2CCAh
2CCBh
2CCCh
2CCDh
2CCEh
2CCFh
2CD0h
DTC Control Data 18
2CD1h
2CD2h
2CD3h
2CD4h
2CD5h
2CD6h
2CD7h
2CD8h
DTC Control Data 19
2CD9h
2CDAh
2CDBh
2CDCh
2CDDh
2CDEh
2CDFh
2CE0h
DTC Control Data 20
2CE1h
2CE2h
2CE3h
2CE4h
2CE5h
2CE6h
2CE7h
2CE8h
DTC Control Data 21
2CE9h
2CEAh
2CEBh
2CECh
2CEDh
2CEEh
2CEFh
X: Undefined
Note:
1. The blank areas are reserved and cannot be accessed by users.
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
Symbol
DTCD14
DTCD15
DTCD16
DTCD17
DTCD18
DTCD19
DTCD20
DTCD21
After Reset
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
Page 28 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
4. Special Function Registers (SFRs)
SFR Information (12) (1)
Table 4.12
Address
Register
2CF0h
DTC Control Data 22
2CF1h
2CF2h
2CF3h
2CF4h
2CF5h
2CF6h
2CF7h
2CF8h
DTC Control Data 23
2CF9h
2CFAh
2CFBh
2CFCh
2CFDh
2CFEh
2CFFh
2D00h
:
2FFFh
X: Undefined
Note:
1. The blank areas are reserved and cannot be accessed by users.
Table 4.13
ID Code Areas and Option Function Select Area
Address
:
FFDBh
:
FFDFh
:
FFE3h
:
FFEBh
:
FFEFh
:
FFF3h
:
FFF7h
:
FFFBh
:
FFFFh
Area Name
Notes:
1.
2.
Option Function Select Register 2
Symbol
DTCD22
DTCD23
Symbol
OFS2
After Reset
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
XXh
After Reset
(Note 1)
ID1
(Note 2)
ID2
(Note 2)
ID3
(Note 2)
ID4
(Note 2)
ID5
(Note 2)
ID6
(Note 2)
ID7
(Note 2)
Option Function Select Register
OFS
(Note 1)
The option function select area is allocated in the flash memory, not in the SFRs. Set appropriate values as ROM data by a program.
Do not write additions to the option function select area. If the block including the option function select area is erased, the option function select
area is set to FFh.
When blank products are shipped, the option function select area is set to FFh. It is set to the written value after written by the user.
When factory-programming products are shipped, the value of the option function select area is the value programmed by the user.
The ID code areas are allocated in the flash memory, not in the SFRs. Set appropriate values as ROM data by a program.
Do not write additions to the ID code areas. If the block including the ID code areas is erased, the ID code areas are set to FFh.
When blank products are shipped, the ID code areas are set to FFh. They are set to the written value after written by the user.
When factory-programming products are shipped, the value of the ID code areas is the value programmed by the user.
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
Page 29 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
5.
5. Electrical Characteristics
Electrical Characteristics
Table 5.1
Symbol
Absolute Maximum Ratings
Rated Value
Unit
VCC/AVCC
Supply voltage
Parameter
Condition
−0.3 to 6.5
V
VI
Input voltage (1)
−0.3 to VCC + 0.3
V
IIN
Input current (1)
−4 to 4
mA
VO
Output voltage
Pd
Power dissipation
Topr
Operating ambient temperature
Tstg
Storage temperature
(2, 3, 4)
−40°C ≤ Topr ≤ 85°C
85°C < Topr ≤ 125°C
Notes:
1.
2.
3.
4.
−0.3 to VCC + 0.3
V
300
mW
125
−40 to 85 (J version) /
−40 to 125 (K version)
°C
−65 to 150
°C
Meet the specified range for the input voltage or the input current.
Applicable ports: P1, P3_3 to P3_5, P3_7, P4_5
The total input current must be 12 mA or less.
Even if no voltage is supplied to Vcc, the input current may cause the MCU to be powered on and operate. When a voltage
is supplied to Vcc, the input current may cause the supply voltage to rise. Since operations in any cases other than above are
not guaranteed, use the power supply circuit in the system to ensure the supply voltage for the MCU is stable within the
specified range.
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
Page 30 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
Table 5.2
5. Electrical Characteristics
Recommended Operating Conditions (1)
Symbol
Parameter
Conditions
Standard
Min.
Typ.
Max.
Unit
VCC/AVCC Supply voltage
2.7
−
5.5
VSS/AVSS Supply voltage
−
0
−
V
0.8 VCC
−
VCC
V
VIH
Input “H” voltage
Other than CMOS input
CMOS Input level Input level selection
input
switching : 0.35 VCC
function
Input level selection
(I/O port)
: 0.5 VCC
4.0 V ≤ VCC ≤ 5.5 V
Input level selection
: 0.7 VCC
0.5 VCC
−
VCC
V
2.7 V ≤ VCC < 4.0 V 0.55 VCC
−
VCC
V
4.0 V ≤ VCC ≤ 5.5 V
0.65 VCC
−
VCC
V
2.7 V ≤ VCC < 4.0 V
0.7 VCC
−
VCC
V
4.0 V ≤ VCC ≤ 5.5 V
0.85 VCC
−
VCC
V
2.7 V ≤ VCC < 4.0 V 0.85 VCC
−
VCC
V
1.2
−
VCC
V
0
−
0.2 VCC
V
External clock input (XOUT)
VIL
Input “L” voltage
Other than CMOS input
CMOS Input level
input
switching
function
(I/O port)
V
Input level selection
: 0.35 VCC
4.0 V ≤ VCC ≤ 5.5 V
0
−
0.2 VCC
V
2.7 V ≤ VCC < 4.0 V
0
−
0.2 VCC
V
Input level selection
: 0.5 VCC
4.0 V ≤ VCC ≤ 5.5 V
0
−
0.4 VCC
V
2.7 V ≤ VCC < 4.0 V
0
−
0.3 VCC
V
Input level selection
: 0.7 VCC
4.0 V ≤ VCC ≤ 5.5 V
0
−
0.55 VCC
V
2.7 V ≤ VCC < 4.0 V
0
−
0.45 VCC
V
0
−
0.4
V
External clock input (XOUT)
IOH(sum)
Peak sum output “H” current Sum of all pins IOH(peak)
−
−
−80
mA
IOH(sum)
Average sum output “H” current Sum of all pins IOH(avg)
−
−
−40
mA
IOH(peak)
Peak output “H” current
−
−
−10
mA
IOH(avg)
Average output “H” current
−
−
−5
mA
IOL(sum)
Peak sum output “L” current
−
−
80
mA
IOL(sum)
Average sum output “L” current Sum of all pins IOL(avg)
−
−
40
mA
IOL(peak)
Peak output “L” current
−
−
10
mA
IOL(avg)
Average output “L” current
−
−
5
mA
f(XIN)
XIN clock input oscillation frequency
MHz
Sum of all pins IOL(peak)
2.7 V ≤ VCC ≤ 5.5 V
−
−
20
fOCO40M When used as the count source for timer RC or timer RD (3)
2.7 V ≤ VCC ≤ 5.5 V
32
−
40
MHz
fOCO-F
fOCO-F frequency
2.7 V ≤ VCC ≤ 5.5 V
−
−
20
MHz
−
System clock frequency
2.7 V ≤ VCC ≤ 5.5 V
−
−
20
MHz
f(BCLK)
CPU clock frequency
2.7 V ≤ VCC ≤ 5.5 V
−
−
20
MHz
Notes:
1. VCC = 2.7 to 5.5 V and Topr = −40 to 85°C (J version) / −40 to 125°C (K version), unless otherwise specified.
2. The average output current indicates the average value of current measured during 100 ms.
3. fOCO40M can be used as the count source for timer RC or timer RD in the range of VCC = 2.7 V to 5.5V.
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
Page 31 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
Table 5.3
5. Electrical Characteristics
Recommended Operating Conditions (2)
Symbol
Parameter
Conditions
Standard
Min.
Typ.
Max.
Unit
IIC(H)
High input injection current
P1, P3_3 to P3_5, P3_7, P4_5 VI > VCC
−
−
2
mA
IIC(L)
Low input injection current
P1, P3_3 to P3_5, P3_7, P4_5 VI < VSS
−
−
−2
mA
Σ|IIC|
Total injection current
−
−
8
mA
Note:
1. VCC = 4.5 to 5.5 V and Topr = −40 to 85°C (J version) / −40 to 125°C (K version), unless otherwise specified.
P1
P3
P4
Figure 5.1
30pF
Ports P1, P3 and P4 Timing Measurement Circuit
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
Page 32 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
Table 5.4
Symbol
−
A/D Converter Characteristics
Parameter
Resolution
Absolute accuracy
−
5. Electrical Characteristics
Conditions
10-bit mode
8-bit mode
φAD
−
tCONV
tSAMP
IVref
Vref
VIA
A/D conversion clock
Tolerance level impedance
Conversion time
10-bit mode
8-bit mode
Sampling time
Vref current
Reference voltage
Analog input voltage (3)
OCVREF On-chip reference voltage
Standard
Typ.
Max.
−
10
−
±3
−
±5
−
±2
−
±2
−
20
Unit
4.0 V ≤ Vref = AVCC ≤ 5.5 V (2)
Min.
−
−
−
−
−
2
2.7 V ≤ Vref = AVCC ≤ 5.5 V (2)
2
−
10
MHz
2.2 V ≤ Vref = AVCC ≤ 5.5 V (2)
2
−
5
MHz
−
−
−
AVCC
Vref
kΩ
µs
µs
µs
µA
V
V
1.54
V
Vref = AVCC
Vref = AVCC = 5.0 V
Vref = AVCC = 3.0 V
Vref = AVCC = 5.0 V
Vref = AVCC = 3.0 V
AN8 to AN11 input
AN8 to AN11 input
AN8 to AN11 input
AN8 to AN11 input
Vref = AVCC = 5.0 V, φAD = 20 MHz
Vref = AVCC = 5.0 V, φAD = 20 MHz
φAD = 20 MHz
VCC = 5 V, XIN = f1 = φAD = 20 MHz
2.2
2.2
0.80
−
2.7
0
3
−
−
−
45
−
−
2 MHz ≤ φAD ≤ 4 MHz
1.14
1.34
−
−
−
Bit
LSB
LSB
LSB
LSB
MHz
Notes:
1. VCC/AVCC = Vref = 2.7 to 5.5 V, VSS = 0 V and Topr = −40 to 85°C (J version) / −40 to 125°C (K version), unless otherwise
specified.
2. The A/D conversion result will be undefined in wait mode, stop mode, when the flash memory stops, and in low-currentconsumption mode. Do not perform A/D conversion in these states or transition to these states during A/D conversion.
3. When the analog input voltage is over the reference voltage, the A/D conversion result will be 3FFh in 10-bit mode and FFh in
8-bit mode.
Table 5.5
Symbol
Vref
VI
−
td
ICMP
Comparator B Electrical Characteristics
Parameter
Condition
IVREF1, IVREF3 input reference voltage
IVCMP1, IVCMP3 input voltage
Offset
Comparator output delay time (2)
Comparator operating current
VI = Vref ± 100 mV
VCC = 5.0 V
Min.
0
−0.3
−
−
−
Standard
Typ.
Max.
−
VCC − 1.4
−
VCC + 0.3
5
100
0.1
−
17.5
−
Unit
V
V
mV
µs
µA
Notes:
1. VCC = 2.7 to 5.5 V, Topr = −40 to 85°C (J version) / −40 to 125°C (K version), unless otherwise specified.
2. When the digital filter is disabled.
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
Page 33 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
Table 5.6
Symbol
−
−
−
−
td(SR-SUS)
−
−
5. Electrical Characteristics
Flash Memory (Program ROM) Electrical Characteristics
Parameter
Program/erase endurance (2)
Conditions
Unit
Max.
−
times
1,000 (3)
R8C/32H Group
100 (3)
−
−
−
times
80
300
µs
−
80
500
µs
−
−
0.3
−
s
ms
0
−
4
5+CPU clock ×
3 cycles
−
−
−
µs
−
−
2.7
2.7
−40
−
20
−
30+CPU clock ×
1 cycle
30+CPU clock ×
1 cycle
5.5
5.5
85 (J version)
125 (K version)
−
Byte program time
(program/erase endurance ≤ 100 times)
Byte program time
(program/erase endurance > 100 times)
Block erase time
Time delay from suspend request until
suspend
Interval from erase start/restart until
following suspend request
Time from suspend until erase restart
Data hold time (7)
Standard
Typ.
−
R8C/32G Group
td(CMDRST- Time from when command is forcibly
READY)
terminated until reading is enabled
−
Program, erase voltage
−
Read voltage
−
Program, erase temperature
−
Min.
Ambient temperature =
55°C (8)
−
−
µs
µs
V
V
°C
year
Notes:
1. VCC = 2.7 to 5.5 V at Topr = -40 to 85°C (J version) / -40 to 125°C (K version) (under consideration), unless otherwise
specified.
2. Definition of programming/erasure endurance
The programming and erasure endurance is defined on a per-block basis.
If the programming and erasure endurance is n (n = 100, 1,000), each block can be erased n times. For example, if 4,096 1byte writes are performed to different addresses in block, a 4 Kbyte block, and then the block is erased, the
programming/erasure endurance still stands at one.
However, the same address must not be programmed more than once per erase operation (overwriting prohibited).
3. Endurance to guarantee all electrical characteristics after program and erase. (1 to Min. value can be guaranteed).
4. In a system that executes multiple programming operations, the actual erasure count can be reduced by writing to sequential
addresses in turn so that as much of the block as possible is used up before performing an erase operation. For example,
when programming groups of 16 bytes, the effective number of rewrites can be minimized by programming up to 128 groups
before erasing them all in one operation. It is also advisable to retain data on the erasure endurance of each block and limit
the number of erase operations to a certain number.
5. If an error occurs during block erase, attempt to execute the clear status register command, then execute the block erase
command at least three times until the erase error does not occur.
6. Customers desiring program/erase failure rate information should contact their Renesas technical support representative.
7. The data hold time includes time that the power supply is off or the clock is not supplied.
8. This data hold time includes 3,000 hours in Ta = 125°C and 7,000 hours in Ta = 85°C.
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
Page 34 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
Table 5.7
Symbol
−
−
−
−
−
td(SR-SUS)
−
−
5. Electrical Characteristics
Flash Memory (Data flash Block A to Block D) Electrical Characteristics
Parameter
Conditions
Program/erase endurance (2)
Byte program time
(program/erase endurance ≤ 1,000 times)
Byte program time
(program/erase endurance > 1,000 times)
Block erase time
(program/erase endurance ≤ 1,000 times)
Block erase time
(program/erase endurance > 1,000 times)
Time delay from suspend request until
suspend
Interval from erase start/restart until
following suspend request
Time from suspend until erase restart
Data hold time (7)
Max.
−
times
−
160
950
µs
−
300
950
µs
−
0.2
1
s
−
0.3
1
s
−
−
ms
0
−
3+CPU clock × 3
cycles
−
−
−
µs
−
−
2.7
2.7
−
−40
−
20
−
30+CPU clock × 1
cycle
30+CPU clock × 1
cycle
5.5
5.5
85°C (J version),
125°C (K version)
−
10,000 (3)
td(CMDRST- Time from when command is forcibly
READY)
terminated until reading is enabled
−
Program, erase voltage
−
Read voltage
−
Program, erase temperature
−
Standard
Typ.
−
Min.
Ambient temperature =
55 °C (8)
−
Unit
µs
µs
V
V
°C
year
Notes:
1. VCC = 2.7 to 5.5 V and Topr = −40 to 85°C (J version) / −40 to 125°C (K version), unless otherwise specified.
2. Definition of programming/erasure endurance
The programming and erasure endurance is defined on a per-block basis.
If the programming and erasure endurance is n (n = 10,000), each block can be erased n times. For example, if 1,024 1-byte
writes are performed to different addresses in block A, a 1 Kbyte block, and then the block is erased, the
programming/erasure endurance still stands at one.
However, the same address must not be programmed more than once per erase operation (overwriting prohibited).
3. Endurance to guarantee all electrical characteristics after program and erase. (1 to Min. value can be guaranteed).
4. In a system that executes multiple programming operations, the actual erasure count can be reduced by writing to sequential
addresses in turn so that as much of the block as possible is used up before performing an erase operation. For example,
when programming groups of 16 bytes, the effective number of rewrites can be minimized by programming up to 128 groups
before erasing them all in one operation. In addition, averaging the erasure endurance between blocks A to D can further
reduce the actual erasure endurance. It is also advisable to retain data on the erasure endurance of each block and limit the
number of erase operations to a certain number.
5. If an error occurs during block erase, attempt to execute the clear status register command, then execute the block erase
command at least three times until the erase error does not occur.
6. Customers desiring program/erase failure rate information should contact their Renesas technical support representative.
7. The data hold time includes time that the power supply is off or the clock is not supplied.
8. This data hold time includes 3,000 hours in Ta = 125°C and 7,000 hours in Ta = 85°C.
Suspend request
(FMR21 bit)
FST7 bit
FST6 bit
Fixed time
Clock-dependent
time
Access restart
td(SR-SUS)
FST6, FST7: Bit in FST register
FMR21: Bit in FMR2 register
Figure 5.2
Time delay until Suspend
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
Page 35 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
Table 5.8
5. Electrical Characteristics
Voltage Detection 0 Circuit Electrical Characteristics
Symbol
Parameter
Condition
Vdet0
Voltage detection level
−
Voltage detection 0 circuit response time (3)
−
td(E-A)
Voltage detection circuit self power consumption
Waiting time until voltage detection circuit
operation starts (2)
At the falling of VCC
At the falling of VCC from 5 V
to (Vdet0_0 − 0.1) V
VCA25 = 1, VCC = 5.0 V
Min.
Standard
Typ.
Max.
2.70
−
2.85
6
3.05
150
−
1.5
−
−
100
−
Unit
V
µs
µA
µs
Notes:
1. The measurement condition is VCC = 2.7 V to 5.5 V and Topr = −40 to 85°C (J version) / −40 to 125°C (K version).
2. Necessary time until the voltage detection circuit operates when setting to 1 again after setting the VCA25 bit in the VCA2
register to 0.
3. Time until the voltage monitor 0 reset is generated after the voltage passes Vdet0.
Table 5.9
Voltage Detection 1 Circuit Electrical Characteristics
Symbol
Parameter
Condition
Standard
Typ.
Max.
3.25
3.55
Unit
Voltage detection level Vdet1_7 (2)
At the falling of VCC
Min.
2.95
Voltage detection level Vdet1_8 (2)
At the falling of VCC
3.10
3.40
3.70
V
Voltage detection level Vdet1_9
(2)
At the falling of VCC
3.25
3.55
3.85
V
Voltage detection level Vdet1_A
(2)
At the falling of VCC
3.40
3.70
4.00
V
Voltage detection level Vdet1_B (2)
At the falling of VCC
3.55
3.85
4.15
V
Voltage detection level Vdet1_C (2)
At the falling of VCC
3.70
4.00
4.30
V
Voltage detection level Vdet1_D (2)
At the falling of VCC
3.80
4.15
4.45
V
(2)
4.00
4.30
4.60
V
−
Voltage detection level Vdet1_E
Hysteresis width at the rising of Vcc in voltage
detection 1 circuit
At the falling of VCC
−
0.10
−
V
−
Voltage detection 1 circuit response time (3)
−
60
150
µs
−
td(E-A)
Voltage detection circuit self power consumption
Waiting time until voltage detection circuit operation
starts (4)
At the falling of VCC from
5 V to (Vdet1_7 − 0.1) V
VCA26 = 1, VCC = 5.0 V
−
1.7
−
−
100
µA
Vdet1
Notes:
1.
2.
3.
4.
−
V
µs
The measurement condition is VCC = 2.7 V to 5.5 V and Topr = −40 to 85°C (J version) / −40 to 125°C (K version).
Select the voltage detection level with bits VD1S0 to VD1S3 in the VD1LS register.
Time until the voltage monitor 1 interrupt request is generated after the voltage passes Vdet1.
Necessary time until the voltage detection circuit operates when setting to 1 again after setting the VCA26 bit in the VCA2
register to 0.
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
Page 36 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
Table 5.10
Voltage Detection 2 Circuit Electrical Characteristics
Symbol
Vdet2
5. Electrical Characteristics
Parameter
Condition
Voltage detection level Vdet2
At the falling of VCC
Hysteresis width at the rising of Vcc in voltage detection
2 circuit
At the falling of Vcc from
Voltage detection 2 circuit response time (2)
5 V to (Vdet2_0 − 0.1) V
Voltage detection circuit self power consumption
VCA27 = 1, VCC = 5.0 V
Waiting time until voltage detection circuit operation
starts (3)
−
−
−
td(E-A)
Min.
3.70
−
Standard
Typ.
Max.
4.00
4.30
0.10
−
Unit
V
V
−
20
150
µs
−
1.7
−
−
100
µA
−
µs
Notes:
1. The measurement condition is VCC = 2.7 V to 5.5 V and Topr = −40 to 85°C (J version) / −40 to 125°C (K version).
2. Time until the voltage monitor 2 interrupt request is generated after the voltage passes Vdet2.
3. Necessary time until the voltage detection circuit operates after setting to 1 again after setting the VCA27 bit in the VCA2
register to 0.
Table 5.11
Power-on Reset Circuit (2)
Symbol
trth
Parameter
Condition
External power VCC rise gradient
(1)
Min.
0
Standard
Unit
Typ.
Max.
−
50,000 mV/msec
Notes:
1. The measurement condition is Topr = −40 to 85°C (J version) / −40 to 125°C (K version), unless otherwise specified.
2. To use the power-on reset function, enable voltage monitor 0 reset by setting the LVDAS bit in the OFS register to 0.
Vdet0 (1)
Vdet0 (1)
trth
trth
External
Power VCC
0.5 V
tw(por) (2)
Voltage detection 0
circuit response time
Internal
reset signal
1
× 32
fOCO-S
1
× 32
fOCO-S
Notes:
1. Vdet0 indicates the voltage detection level of the voltage detection 0 circuit. Refer to 6. Voltage Detection
Circuit of User’s Manual: Hardware for details.
2. tw(por) indicates the duration the external power VCC must be held below the valid voltage (0.5 V) to enable
a power-on reset. When turning on the power after it falls with voltage monitor 0 reset disabled, maintain
tw(por) for 1 ms or more.
Figure 5.3
Power-on Reset Circuit Electrical Characteristics
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
Page 37 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
Table 5.12
High-speed On-Chip Oscillator Circuit Electrical Characteristics
Symbol
−
5. Electrical Characteristics
Parameter
High-speed on-chip oscillator frequency after
reset
High-speed on-chip oscillator frequency when
the FRA4 register correction value is written into
the FRA1 register and the FRA5 register
correction value into the FRA3 register (3)
High-speed on-chip oscillator frequency when
the FRA6 register correction value is written into
the FRA1 register and the FRA7 register
correction value into the FRA3 register
High-speed on-chip oscillator frequency
temperature • supply voltage dependence (2)
Oscillation stability time
Self power consumption at oscillation
−
−
Condition
VCC = 2.7 V to 5.5 V,
−40°C ≤ Topr ≤ 85°C (J) /
−40°C ≤ Topr ≤ 125°C (K)
VCC = 5.0 V, Topr = 25°C
Min.
−
Standard
Typ.
40
Max.
−
MHz
−
36.864
−
MHz
−
32
−
MHz
−5
−
5
%
−
200
400
−
µs
−
µA
−
Unit
Notes:
1. The measurement condition is VCC = 2.7 to 5.5 V, Topr = −40 to 85°C (J version) / −40 to 125°C (K version).
2. This indicates the precision error for the oscillation frequency of the high-speed on-chip oscillator.
3. This enables the setting errors of bit rates such as 9600 bps and 38400 bps to be 0% when the serial interface is used in
UART mode.
Table 5.13
Low-speed On-Chip Oscillator Circuit Electrical Characteristics
Symbol
Parameter
fOCO-S
Low-speed on-chip oscillator frequency
fOCO-WDT
Low-speed on-chip oscillator frequency for watchdog
timer
−
Oscillation stability time
Self power consumption at oscillation
−
Condition
2.7 V ≤ VCC < 4.2 V
4.2 V ≤ VCC ≤ 5.5 V
2.7 V ≤ VCC < 4.2 V
4.2 V ≤ VCC ≤ 5.5 V
VCC = 5.0 V, Topr = 25°C
VCC = 5.0 V, Topr = 25°C
Min.
106.25
112.5
106.25
112.5
−
−
Standard
Typ.
125
125
125
125
30
3
Max.
143.75
137.5
143.75
137.5
100
−
Unit
kHz
kHz
µs
µA
Note:
1. The measurement condition is VCC = 2.7 to 5.5 V, Topr = −40 to 85°C (J version) / −40 to 125°C (K version).
Table 5.14
Power Supply Circuit Timing Characteristics
Symbol
td(P-R)
Parameter
Time for internal power supply stabilization during
power-on (2)
Condition
Min.
−
Standard
Typ.
Max.
−
2,000
Unit
µs
Notes:
1. The measurement condition is VCC = 2.7 V to 5.5 V and Topr = -40 to 85°C (J version) / -40 to 125°C (K version).
2. Waiting time until the internal power supply generation circuit stabilizes during power-on.
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
Page 38 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
Table 5.15
Symbol
Timing Requirements of Synchronous Serial Communication Unit (SSU) (1)
Parameter
tSUCYC
SSCK clock cycle time
tHI
tLO
tRISE
SSCK clock “H” width
SSCK clock “L” width
SSCK clock rising
time
tFALL
5. Electrical Characteristics
SSCK clock falling
time
Conditions
Standard
Typ.
−
−
Max.
−
tCYC (2)
tSUCYC
tSUCYC
−
−
−
−
−
−
100
1
−
1
−
−
tCYC (2)
µs
ns
−
−
tCYC (2)
Slave
1tCYC + 50
−
−
ns
Slave
1tCYC + 50
−
−
ns
−
−
1
−
−
−
−
1.5tCYC + 100
1.5tCYC + 100
tCYC (2)
ns
ns
Master
Slave
Master
Slave
SSO, SSI data input setup time
SSO, SSI data input hold time
tLEAD
SCS setup time
tOD
SCS hold time
SSO, SSI data output delay time
tSA
tOR
SSI slave access time
SSI slave out open time
2.7 V ≤ VCC ≤ 5.5 V
2.7 V ≤ VCC ≤ 5.5 V
−
0.6
0.6
1
Unit
0.4
0.4
−
tSU
tH
tLAG
Min.
4
1
1
tCYC (2)
µs
Notes:
1. VCC = 2.7 to 5.5 V, VSS = 0 V and Topr = −40 to 85°C (J version) / −40 to 125°C (K version), unless otherwise specified.
2. 1tCYC = 1/f1(s)
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
Page 39 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
5. Electrical Characteristics
4-Wire Bus Communication Mode, Master, CPHS = 1
VIH or VOH
SCS (output)
VIL or VOL
tHI
tFALL
tRISE
SSCK (output)
(CPOS = 1)
tLO
tHI
SSCK (output)
(CPOS = 0)
tLO
tSUCYC
SSO (output)
tOD
SSI (input)
tSU
tH
4-Wire Bus Communication Mode, Master, CPHS = 0
VIH or VOH
SCS (output)
VIL or VOL
tHI
tFALL
tRISE
SSCK (output)
(CPOS = 1)
tLO
tHI
SSCK (output)
(CPOS = 0)
tLO
tSUCYC
SSO (output)
tOD
SSI (input)
tSU
tH
CPHS, CPOS: Bits in SSMR register
Figure 5.4
I/O Timing of Synchronous Serial Communication Unit (SSU) (Master)
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
Page 40 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
5. Electrical Characteristics
4-Wire Bus Communication Mode, Slave, CPHS = 1
VIH or VOH
SCS (input)
VIL or VOL
tLEAD
tHI
tFALL
tRISE
tLAG
SSCK (input)
(CPOS = 1)
tLO
tHI
SSCK (input)
(CPOS = 0)
tLO
tSUCYC
SSO (input)
tSU
tH
SSI (output)
tSA
tOD
tOR
4-Wire Bus Communication Mode, Slave, CPHS = 0
VIH or VOH
SCS (input)
VIL or VOL
tLEAD
tHI
tFALL
tRISE
tLAG
SSCK (input)
(CPOS = 1)
tLO
tHI
SSCK (input)
(CPOS = 0)
tLO
tSUCYC
SSO (input)
tSU
tH
SSI (output)
tSA
tOD
tOR
CPHS, CPOS: Bits in SSMR register
Figure 5.5
I/O Timing of Synchronous Serial Communication Unit (SSU) (Slave)
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
Page 41 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
5. Electrical Characteristics
tHI
VIH or VOH
SSCK
VIL or VOL
tLO
tSUCYC
SSO (output)
tOD
SSI (input)
tSU
Figure 5.6
tH
I/O Timing of Synchronous Serial Communication Unit (SSU) (Clock Synchronous
Communication Mode)
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
Page 42 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
Table 5.16
Electrical Characteristics (1) [4.2 V ≤ Vcc ≤ 5.5 V]
Symbol
Parameter
VOH
Output “H” voltage
Other than XOUT
VOL
Output “L” voltage
XOUT
Other than XOUT
VT+-VT-
Hysteresis
IIH
IIL
RPULLUP
RfXIN
Input “H” current
Input “L” current
Pull-up resistance
Feedback
resistance
RAM hold voltage
XOUT
INT0, INT1, INT3,
KI0, KI1, KI2, KI3,
TRAIO, TRBO,
TRCIOA, TRCIOB,
TRCIOC, TRCIOD,
TRDIOA0, TRDIOB0,
TRDIOC0, TRDIOD0,
TRDIOA1, TRDIOB1,
TRDIOC1, TRDIOD1,
TRCTRG, TRCCLK,
ADTRG,
RXD0, RXD2, CLK0,
CLK2, SSI, SCL,
SDA, SSO
RESET
VRAM
5. Electrical Characteristics
Condition
IOH = −5 mA
IOH = −200 µA
IOH = −200 µA
IOL = 5 mA
IOL = 200 µA
IOL = 200 µA
VCC = 5.0 V
VCC = 5.0 V
VI = 5 V, VCC = 5.0 V
VI = 0 V, VCC = 5.0 V
VI = 0 V, VCC = 5.0 V
XIN
During stop mode
Min.
VCC − 2.0
VCC − 0.3
1.0
−
−
−
0.1
Standard
Typ.
−
−
−
−
−
−
1.2
0.1
1.2
−
V
−
−
µA
−
25
−
−
50
0.3
1.0
−1.0
100
−
µA
kΩ
MΩ
2.0
−
−
V
Max.
VCC
VCC
VCC
2.0
0.45
0.5
−
Unit
V
V
V
V
V
V
V
Note:
1. 4.2 V ≤ VCC ≤ 5.5 V and Topr = −40 to 85°C (J version) / −40 to 125°C (K version), f(XIN) = 20 MHz, unless otherwise
specified.
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
Page 43 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
Table 5.17
Symbol
ICC
5. Electrical Characteristics
Electrical Characteristics (2) [3.3 V ≤ Vcc ≤ 5.5 V]
(Topr = −40 to 85°C (J version), unless otherwise specified.)
Parameter
Condition
Power supply
High-speed
current
clock mode
(VCC = 3.3 to 5.5 V)
Single-chip mode,
output pins are
open, other pins
are VSS
High-speed
on-chip
oscillator mode
Low-speed
on-chip
oscillator mode
Wait mode
Stop mode
XIN = 20 MHz (square wave)
High-speed on-chip oscillator off
Low-speed on-chip oscillator on = 125 kHz
No division
XIN = 16 MHz (square wave)
High-speed on-chip oscillator off
Low-speed on-chip oscillator on = 125 kHz
No division
XIN = 10 MHz (square wave)
High-speed on-chip oscillator off
Low-speed on-chip oscillator on = 125 kHz
No division
XIN = 20 MHz (square wave)
High-speed on-chip oscillator off
Low-speed on-chip oscillator on = 125 kHz
Divide-by-8
XIN = 16 MHz (square wave)
High-speed on-chip oscillator off
Low-speed on-chip oscillator on = 125 kHz
Divide-by-8
XIN = 10 MHz (square wave)
High-speed on-chip oscillator off
Low-speed on-chip oscillator on = 125 kHz
Divide-by-8
XIN clock off
High-speed on-chip oscillator on fOCO-F = 20 MHz
Low-speed on-chip oscillator on = 125 kHz
No division
XIN clock off
High-speed on-chip oscillator on fOCO-F = 20 MHz
Low-speed on-chip oscillator on = 125 kHz
Divide-by-8
XIN clock off
High-speed on-chip oscillator off
Low-speed on-chip oscillator on = 125 kHz
Divide-by-8, FMR27 = 1, VCA20 = 0
XIN clock off
High-speed on-chip oscillator off
Low-speed on-chip oscillator on = 125 kHz
While a WAIT instruction is executed
Peripheral clock operation
VCA27 = VCA26 = VCA25 = 0
VCA20 = 1
XIN clock off
High-speed on-chip oscillator off
Low-speed on-chip oscillator on = 125 kHz
While a WAIT instruction is executed
Peripheral clock off
VCA27 = VCA26 = VCA25 = 0
VCA20 = 1
XIN clock off, Topr = 25°C
High-speed on-chip oscillator off
Low-speed on-chip oscillator off
CM10 = 1
Peripheral clock off
VCA27 = VCA26 = VCA25 = 0
XIN clock off, Topr = 85°C
High-speed on-chip oscillator off
Low-speed on-chip oscillator off
CM10 = 1
Peripheral clock off
VCA27 = VCA26 = VCA25 = 0
Min.
−
Standard
Typ.
Max.
7.0
15
Unit
mA
−
5.6
12.5
mA
−
3.6
−
mA
−
3.0
−
mA
−
2.2
−
mA
−
1.5
−
mA
−
7.0
15
mA
−
3.0
−
mA
−
90
180
µA
−
15
110
µA
−
5.0
100
µA
−
2.0
5.0
µA
−
15.0
−
µA
Note:
1. The typical value (Typ.) indicates the current value when the CPU and the memory operate.
The maximum value (Max.) indicates the current when the CPU, the memory, and the peripheral functions operate and the
flash memory is programmed/erased.
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
Page 44 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
Table 5.18
Symbol
ICC
5. Electrical Characteristics
Electrical Characteristics (3) [3.3 V ≤ Vcc ≤ 5.5 V]
(Topr = −40 to 125°C (K version), unless otherwise specified.)
Parameter
Condition
Power supply
High-speed
current
clock mode
(VCC = 3.3 to 5.5 V)
Single-chip mode,
output pins are
open, other pins
are VSS
High-speed
on-chip
oscillator mode
Low-speed
on-chip
oscillator mode
Wait mode
Stop mode
XIN = 20 MHz (square wave)
High-speed on-chip oscillator off
Low-speed on-chip oscillator on = 125 kHz
No division
XIN = 16 MHz (square wave)
High-speed on-chip oscillator off
Low-speed on-chip oscillator on = 125 kHz
No division
XIN = 10 MHz (square wave)
High-speed on-chip oscillator off
Low-speed on-chip oscillator on = 125 kHz
No division
XIN = 20 MHz (square wave)
High-speed on-chip oscillator off
Low-speed on-chip oscillator on = 125 kHz
Divide-by-8
XIN = 16 MHz (square wave)
High-speed on-chip oscillator off
Low-speed on-chip oscillator on = 125 kHz
Divide-by-8
XIN = 10 MHz (square wave)
High-speed on-chip oscillator off
Low-speed on-chip oscillator on = 125 kHz
Divide-by-8
XIN clock off
High-speed on-chip oscillator on fOCO-F = 20 MHz
Low-speed on-chip oscillator on = 125 kHz
No division
XIN clock off
High-speed on-chip oscillator on fOCO-F = 20 MHz
Low-speed on-chip oscillator on = 125 kHz
Divide-by-8
XIN clock off
High-speed on-chip oscillator off
Low-speed on-chip oscillator on = 125 kHz
Divide-by-8, FMR27 = 1, VCA20 = 0
XIN clock off
High-speed on-chip oscillator off
Low-speed on-chip oscillator on = 125 kHz
While a WAIT instruction is executed
Peripheral clock operation
VCA27 = VCA26 = VCA25 = 0
VCA20 = 1
XIN clock off
High-speed on-chip oscillator off
Low-speed on-chip oscillator on = 125 kHz
While a WAIT instruction is executed
Peripheral clock off
VCA27 = VCA26 = VCA25 = 0
VCA20 = 1
XIN clock off, Topr = 25°C
High-speed on-chip oscillator off
Low-speed on-chip oscillator off
CM10 = 1
Peripheral clock off
VCA27 = VCA26 = VCA25 = 0
XIN clock off, Topr = 125°C
High-speed on-chip oscillator off
Low-speed on-chip oscillator off
CM10 = 1
Peripheral clock off
VCA27 = VCA26 = VCA25 = 0
Min.
−
Standard
Typ.
Max.
7.0
15
Unit
mA
−
5.6
12.5
mA
−
3.6
−
mA
−
3.0
−
mA
−
2.2
−
mA
−
1.5
−
mA
−
7.0
15
mA
−
3.0
−
mA
−
90
400
µA
−
15
330
µA
−
5.0
320
µA
−
2.0
5.0
µA
−
60
−
µA
Note:
1. The typical value (Typ.) indicates the current value when the CPU and the memory operate.
The maximum value (Max.) indicates the current when the CPU, the memory, and the peripheral functions operate and the
flash memory is programmed/erased.
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
Page 45 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
5. Electrical Characteristics
Timing Requirements
(Unless Otherwise Specified: VCC = 5 V, VSS = 0 V at Topr = −40°C to 85°C (J ver)/−40°C to 125°C (K ver))
Table 5.19
External Clock Input (XOUT)
Symbol
tc(XOUT)
tWH(XOUT)
tWL(XOUT)
Standard
Min.
Max.
50
−
24
−
24
−
Parameter
XOUT input cycle time
XOUT input “H” width
XOUT input “L” width
tC(XOUT)
Unit
ns
ns
ns
VCC = 5 V
tWH(XOUT)
External Clock Input
tWL(XOUT)
Figure 5.7
Table 5.20
External Clock Input Timing Diagram when VCC = 5 V
TRAIO Input
Symbol
tc(TRAIO)
tWH(TRAIO)
tWL(TRAIO)
Standard
Min.
Max.
100
−
40
−
40
−
Parameter
TRAIO input cycle time
TRAIO input “H” width
TRAIO input “L” width
tC(TRAIO)
Unit
ns
ns
ns
VCC = 5 V
tWH(TRAIO)
TRAIO input
tWL(TRAIO)
Figure 5.8
TRAIO Input Timing Diagram when VCC = 5 V
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
Page 46 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
Table 5.21
Serial Interface
Symbol
tc(CK)
tW(CKH)
tW(CKL)
td(C-Q)
th(C-Q)
tsu(D-C)
th(C-D)
td(C-Q)
tsu(D-C)
th(C-D)
5. Electrical Characteristics
Parameter
Condition
CLKi input cycle time
CLKi input “H” width
CLKi input “L” width
TXDi output delay time
TXDi hold time
RXDi input setup time
RXDi input hold time
TXDi output delay time
RXDi input setup time
RXDi input hold time
When external clock selected
When internal clock selected
Standard
Min.
Max.
200
−
100
−
100
−
−
90
0
−
10
−
90
−
−
10
90
−
90
−
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
i = 0, 2
VCC = 5 V
tC(CK)
tW(CKH)
CLKi
tW(CKL)
th(C-Q)
TXDi
td(C-Q)
tsu(D-C)
th(C-D)
RXDi
i = 0, 2
Figure 5.9
Table 5.22
Serial Interface Timing Diagram when VCC = 5 V
External Interrupt INTi (i = 0 to 1, 3) Input, Key Input Interrupt KIi (i = 0 to 3)
INTi input “H” width, KIi input “H” width
Standard
Min.
Max.
−
250 (1)
INTi input “L” width, KIi input “L” width
250 (2)
Symbol
tW(INH)
tW(INL)
Parameter
−
Unit
ns
ns
Notes:
1. When selecting the digital filter by the INTi input filter select bit, use an INTi input HIGH width of either (1/digital filter clock
frequency × 3) or the minimum value of standard, whichever is greater.
2. When selecting the digital filter by the INTi input filter select bit, use an INTi input LOW width of either (1/digital filter clock
frequency × 3) or the minimum value of standard, whichever is greater.
VCC = 5 V
INTi input
(i = 0 to 1, 3)
tW(INL)
KIi input
(i = 0 to 3)
Figure 5.10
tW(INH)
Input Timing Diagram for External Interrupt INTi and Key Input Interrupt KIi when Vcc
=5V
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
Page 47 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
Table 5.23
Electrical Characteristics (4) [2.7 V ≤ Vcc < 4.2 V]
Symbol
Min.
VCC − 0.5
1.0
−
−
0.1
Standard
Typ.
−
−
−
−
0.4
0.1
0.5
−
V
−
−
µA
XIN
−
42
−
−
84
0.3
1.0
−1.0
168
−
µA
kΩ
MΩ
XCIN
−
8
−
MΩ
2.0
−
−
V
Parameter
VOH
Output “H” voltage
VOL
Output “L” voltage
VT+-VT-
Hysteresis
IIH
IIL
RPULLUP
RfXIN
Input “H” current
Input “L” current
Pull-up resistance
Feedback
resistance
Feedback
resistance
RAM hold voltage
Other than XOUT
XOUT
Other than XOUT
XOUT
INT0, INT1, INT3,
KI0, KI1, KI2, KI3,
TRAIO, TRBO,
TRCIOA, TRCIOB,
TRCIOC, TRCIOD,
TRDIOA0, TRDIOB0,
TRDIOC0, TRDIOD0,
TRDIOA1, TRDIOB1,
TRDIOC1, TRDIOD1,
TRCTRG, TRCCLK,
ADTRG,
RXD0, RXD2, CLK0,
CLK2, SSI, SCL,
SDA, SSO
RESET
RfXCIN
VRAM
5. Electrical Characteristics
Condition
IOH = −1 mA
IOH = −200 µA
IOL = 1 mA
IOL = 200 µA
VCC = 3.0 V
VCC = 3.0 V
VI = 3 V, VCC = 3.0 V
VI = 0 V, VCC = 3.0 V
VI = 0 V, VCC = 3.0 V
During stop mode
Max.
VCC
VCC
0.5
0.5
−
Unit
V
V
V
V
V
Note:
1. 2.7 V ≤ VCC < 4.2 V and Topr = −40 to 85°C (J version) / −40 to 125°C (K version), f(XIN) = 10 MHz, unless otherwise
specified.
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
Page 48 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
Table 5.24
Symbol
ICC
5. Electrical Characteristics
Electrical Characteristics (5) [2.7 V ≤ Vcc < 3.3 V]
(Topr = −40 to 85°C (J version), unless otherwise specified.)
Parameter
Condition
Power supply current High-speed
(VCC = 2.7 to 3.3 V)
clock mode
(1)
Single-chip mode,
output pins are open,
other pins are VSS
High-speed
on-chip
oscillator
mode (1)
Low-speed
on-chip
oscillator
mode
Wait mode
Stop mode
XIN = 20 MHz (square wave)
High-speed on-chip oscillator off
Low-speed on-chip oscillator on = 125 kHz
No division
XIN = 16 MHz (square wave)
High-speed on-chip oscillator off
Low-speed on-chip oscillator on = 125 kHz
No division
XIN = 10 MHz (square wave)
High-speed on-chip oscillator off
Low-speed on-chip oscillator on = 125 kHz
No division
XIN = 20 MHz (square wave)
High-speed on-chip oscillator off
Low-speed on-chip oscillator on = 125 kHz
Divide-by-8
XIN = 16 MHz (square wave)
High-speed on-chip oscillator off
Low-speed on-chip oscillator on = 125 kHz
Divide-by-8
XIN = 10 MHz (square wave)
High-speed on-chip oscillator off
Low-speed on-chip oscillator on = 125 kHz
Divide-by-8
XIN clock off
High-speed on-chip oscillator on fOCO-F = 20 MHz
Low-speed on-chip oscillator on = 125 kHz
No division
XIN clock off
High-speed on-chip oscillator on fOCO-F = 20 MHz
Low-speed on-chip oscillator on = 125 kHz
Divide-by-8
XIN clock off
High-speed on-chip oscillator off
Low-speed on-chip oscillator on = 125 kHz
Divide-by-8, FMR27 = 1, VCA20 = 0
XIN clock off
High-speed on-chip oscillator off
Low-speed on-chip oscillator on = 125 kHz
While a WAIT instruction is executed
Peripheral clock operation
VCA27 = VCA26 = VCA25 = 0
VCA20 = 1
XIN clock off
High-speed on-chip oscillator off
Low-speed on-chip oscillator on = 125 kHz
While a WAIT instruction is executed
Peripheral clock off
VCA27 = VCA26 = VCA25 = 0
VCA20 = 1
XIN clock off, Topr = 25°C
High-speed on-chip oscillator off
Low-speed on-chip oscillator off
CM10 = 1
Peripheral clock off
VCA27 = VCA26 = VCA25 = 0
XIN clock off, Topr = 85°C
High-speed on-chip oscillator off
Low-speed on-chip oscillator off
CM10 = 1
Peripheral clock off
VCA27 = VCA26 = VCA25 = 0
Min.
−
Standard
Typ.
Max.
7.0
14.5
Unit
mA
−
5.6
12.0
mA
−
3.6
−
mA
−
3.0
−
mA
−
2.2
−
mA
−
1.5
−
mA
−
7.0
14.5
mA
−
3.0
−
mA
−
85
180
µA
−
15
110
µA
−
5
100
µA
−
2.0
5.0
µA
−
13.0
−
µA
Note:
1. The typical value (Typ.) indicates the current value when the CPU and the memory operate.
The maximum value (Max.) indicates the current when the CPU, the memory, and the peripheral functions operate and the
flash memory is programmed/erased.
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
Page 49 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
Table 5.25
Symbol
ICC
5. Electrical Characteristics
Electrical Characteristics (6) [2.7 V ≤ Vcc < 3.3 V]
(Topr = −40 to 125°C (K version), unless otherwise specified.)
Parameter
Condition
Power supply current High-speed
(VCC = 2.7 to 3.3 V)
clock mode
(1)
Single-chip mode,
output pins are open,
other pins are VSS
High-speed
on-chip
oscillator
mode (1)
Low-speed
on-chip
oscillator
mode
Wait mode
Stop mode
XIN = 20 MHz (square wave)
High-speed on-chip oscillator off
Low-speed on-chip oscillator on = 125 kHz
No division
XIN = 16 MHz (square wave)
High-speed on-chip oscillator off
Low-speed on-chip oscillator on = 125 kHz
No division
XIN = 10 MHz (square wave)
High-speed on-chip oscillator off
Low-speed on-chip oscillator on = 125 kHz
No division
XIN = 20 MHz (square wave)
High-speed on-chip oscillator off
Low-speed on-chip oscillator on = 125 kHz
Divide-by-8
XIN = 16 MHz (square wave)
High-speed on-chip oscillator off
Low-speed on-chip oscillator on = 125 kHz
Divide-by-8
XIN = 10 MHz (square wave)
High-speed on-chip oscillator off
Low-speed on-chip oscillator on = 125 kHz
Divide-by-8
XIN clock off
High-speed on-chip oscillator on fOCO-F = 20 MHz
Low-speed on-chip oscillator on = 125 kHz
No division
XIN clock off
High-speed on-chip oscillator on fOCO-F = 20 MHz
Low-speed on-chip oscillator on = 125 kHz
Divide-by-8
XIN clock off
High-speed on-chip oscillator off
Low-speed on-chip oscillator on = 125 kHz
Divide-by-8, FMR27 = 1, VCA20 = 0
XIN clock off
High-speed on-chip oscillator off
Low-speed on-chip oscillator on = 125 kHz
While a WAIT instruction is executed
Peripheral clock operation
VCA27 = VCA26 = VCA25 = 0
VCA20 = 1
XIN clock off
High-speed on-chip oscillator off
Low-speed on-chip oscillator on = 125 kHz
While a WAIT instruction is executed
Peripheral clock off
VCA27 = VCA26 = VCA25 = 0
VCA20 = 1
XIN clock off, Topr = 25°C
High-speed on-chip oscillator off
Low-speed on-chip oscillator off
CM10 = 1
Peripheral clock off
VCA27 = VCA26 = VCA25 = 0
XIN clock off, Topr = 125°C
High-speed on-chip oscillator off
Low-speed on-chip oscillator off
CM10 = 1
Peripheral clock off
VCA27 = VCA26 = VCA25 = 0
Min.
−
Standard
Typ.
Max.
7.0
14.5
Unit
mA
−
5.6
12.0
mA
−
3.6
−
mA
−
3.0
−
mA
−
2.2
−
mA
−
1.5
−
mA
−
7.0
14.5
mA
−
3.0
−
mA
−
85
390
µA
−
15
320
µA
−
5
310
µA
−
2.0
5.0
µA
−
55.0
−
µA
Note:
1. The typical value (Typ.) indicates the current value when the CPU and the memory operate.
The maximum value (Max.) indicates the current when the CPU, the memory, and the peripheral functions operate and the
flash memory is programmed/erased.
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
Page 50 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
5. Electrical Characteristics
Timing Requirements
(Unless Otherwise Specified: VCC = 3 V, VSS = 0 V at Topr = −40°C to 85°C (J ver)/−40°C to 125°C (K ver))
Table 5.26
External Clock Input (XOUT)
Symbol
tc(XOUT)
tWH(XOUT)
tWL(XOUT)
Standard
Min.
Max.
50
−
24
−
24
−
Parameter
XOUT input cycle time
XOUT input “H” width
XOUT input “L” width
tC(XOUT)
Unit
ns
ns
ns
VCC = 3 V
tWH(XOUT)
External Clock Input
tWL(XOUT)
Figure 5.11
External Clock Input Timing Diagram when VCC = 3 V
Table 5.27
TRAIO Input
Symbol
tc(TRAIO)
tWH(TRAIO)
tWL(TRAIO)
Standard
Min.
Max.
300
−
120
−
120
−
Parameter
TRAIO input cycle time
TRAIO input “H” width
TRAIO input “L” width
tC(TRAIO)
Unit
ns
ns
ns
VCC = 3 V
tWH(TRAIO)
TRAIO input
tWL(TRAIO)
Figure 5.12
TRAIO Input Timing Diagram when VCC = 3 V
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
Page 51 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
Table 5.28
Serial Interface
Symbol
tc(CK)
tW(CKH)
tW(CKL)
td(C-Q)
th(C-Q)
tsu(D-C)
th(C-D)
td(C-Q)
tsu(D-C)
th(C-D)
5. Electrical Characteristics
Parameter
Condition
CLKi input cycle time
CLKi input “H” width
CLKi Input “L” width
TXDi output delay time
TXDi hold time
RXDi input setup time
RXDi input hold time
TXDi output delay time
RXDi input setup time
RXDi input hold time
When external clock selected
When internal clock selected
Standard
Min.
Max.
300
−
150
−
150
−
−
120
0
−
30
−
90
−
−
30
120
−
90
−
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
i = 0, 2
VCC = 3 V
tC(CK)
tW(CKH)
CLKi
tW(CKL)
th(C-Q)
TXDi
td(C-Q)
tsu(D-C)
th(C-D)
RXDi
i = 0, 2
Figure 5.13
Table 5.29
Serial Interface Timing Diagram when VCC = 3 V
External Interrupt INTi (i = 0 to 1, 3) Input, Key Input Interrupt KIi (i = 0 to 3)
INTi input “H” width, KIi input “H” width
Standard
Min.
Max.
−
380 (1)
INTi input “L” width, KIi input “L” width
380 (2)
Symbol
tW(INH)
tW(INL)
Parameter
Unit
ns
−
ns
Notes:
1. When selecting the digital filter by the INTi input filter select bit, use an INTi input HIGH width of either (1/digital filter clock
frequency × 3) or the minimum value of standard, whichever is greater.
2. When selecting the digital filter by the INTi input filter select bit, use an INTi input LOW width of either (1/digital filter clock
frequency × 3) or the minimum value of standard, whichever is greater.
VCC = 3 V
INTi input
(i = 0 to 1, 3)
tW(INL)
KIi input
(i = 0 to 3)
Figure 5.14
tW(INH)
Input Timing Diagram for External Interrupt INTi and Key Input Interrupt KIi when Vcc
=3V
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
Page 52 of 53
Under development
Preliminary document
Specifications in this document are tentative and subject to change.
R8C/32G Group, R8C/32H Group
Package Dimensions
Package Dimensions
Diagrams showing the latest package dimensions and mounting information are available in the “Packages” section of
the Renesas Electronics website.
JEITA Package Code
P-LSSOP20-4.4x6.5-0.65
RENESAS Code
PLSP0020JB-A
MASS[Typ.]
0.1g
11
*1
E
20
HE
Previous Code
20P2F-A
NOTE)
1. DIMENSIONS "*1" AND "*2"
DO NOT INCLUDE MOLD FLASH.
2. DIMENSION "*3" DOES NOT
INCLUDE TRIM OFFSET.
F
1
Index mark
10
c
A1
Reference
Symbol
D
L
*2
A2
A
S
*3
e
y S
bp
Detail F
D
E
A2
A
A1
bp
c
HE
e
y
L
R01DS0026EJ0010 Rev.0.10
Feb 08, 2011
Dimension in Millimeters
Min
6.4
4.3
Nom Max
6.5 6.6
4.4 4.5
1.15
1.45
0.1 0.2
0
0.17 0.22 0.32
0.13 0.15 0.2
0°
10°
6.2 6.4 6.6
0.53 0.65 0.77
0.10
0.3 0.5 0.7
Page 53 of 53
REVISION HISTORY
Rev.
Date
0.01
Sep 30, 2010
—
0.10
Feb 08, 2011
9
16
21
30 to 52
R8C/32G Group, R8C/32H Group Datasheet
Description
Summary
Page
First Edition issued
Figure 1.4 P3_3 “CTS2/RTS2” → “CTS2/RTS2
3.1 “The internal ROM ... with address 0FFFFh.” deleted
Table 4.4 “00E0h”, “00E2h”, “00E9h”, “00EBh” deleted
“5. Electrical Characteristics” added
All trademarks and registered trademarks are the property of their respective owners.
C-1
General Precautions in the Handling of MPU/MCU Products
The following usage notes are applicable to all MPU/MCU products from Renesas. For detailed usage notes
on the products covered by this manual, refer to the relevant sections of the manual. If the descriptions under
General Precautions in the Handling of MPU/MCU Products and in the body of the manual differ from each
other, the description in the body of the manual takes precedence.
1. Handling of Unused Pins
Handle unused pins in accord with the directions given under Handling of Unused Pins in the
manual.
 The input pins of CMOS products are generally in the high-impedance state. In operation
with an unused pin in the open-circuit state, extra electromagnetic noise is induced in the
vicinity of LSI, an associated shoot-through current flows internally, and malfunctions occur
due to the false recognition of the pin state as an input signal become possible. Unused
pins should be handled as described under Handling of Unused Pins in the manual.
2. Processing at Power-on
The state of the product is undefined at the moment when power is supplied.
 The states of internal circuits in the LSI are indeterminate and the states of register
settings and pins are undefined at the moment when power is supplied.
In a finished product where the reset signal is applied to the external reset pin, the states
of pins are not guaranteed from the moment when power is supplied until the reset
process is completed.
In a similar way, the states of pins in a product that is reset by an on-chip power-on reset
function are not guaranteed from the moment when power is supplied until the power
reaches the level at which resetting has been specified.
3. Prohibition of Access to Reserved Addresses
Access to reserved addresses is prohibited.
 The reserved addresses are provided for the possible future expansion of functions. Do
not access these addresses; the correct operation of LSI is not guaranteed if they are
accessed.
4. Clock Signals
After applying a reset, only release the reset line after the operating clock signal has become
stable. When switching the clock signal during program execution, wait until the target clock
signal has stabilized.
 When the clock signal is generated with an external resonator (or from an external
oscillator) during a reset, ensure that the reset line is only released after full stabilization of
the clock signal. Moreover, when switching to a clock signal produced with an external
resonator (or by an external oscillator) while program execution is in progress, wait until
the target clock signal is stable.
5. Differences between Products
Before changing from one product to another, i.e. to one with a different part number, confirm
that the change will not lead to problems.
 The characteristics of MPU/MCU in the same group but having different part numbers may
differ because of the differences in internal memory capacity and layout pattern. When
changing to products of different part numbers, implement a system-evaluation test for
each of the products.
Notice
1.
All information included in this document is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas
Electronics products listed herein, please confirm the latest product information with a Renesas Electronics sales office. Also, please pay regular and careful attention to additional and different information to
be disclosed by Renesas Electronics such as that disclosed through our website.
2.
Renesas Electronics does not assume any liability for infringement of patents, copyrights, or other intellectual property rights of third parties by or arising from the use of Renesas Electronics products or
technical information described in this document. No license, express, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights of Renesas Electronics or
others.
3.
You should not alter, modify, copy, or otherwise misappropriate any Renesas Electronics product, whether in whole or in part.
4.
Descriptions of circuits, software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples. You are fully responsible for
the incorporation of these circuits, software, and information in the design of your equipment. Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the
use of these circuits, software, or information.
5.
When exporting the products or technology described in this document, you should comply with the applicable export control laws and regulations and follow the procedures required by such laws and
regulations. You should not use Renesas Electronics products or the technology described in this document for any purpose relating to military applications or use by the military, including but not limited to
the development of weapons of mass destruction. Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose manufacture, use, or sale is
prohibited under any applicable domestic or foreign laws or regulations.
6.
Renesas Electronics has used reasonable care in preparing the information included in this document, but Renesas Electronics does not warrant that such information is error free. Renesas Electronics
7.
Renesas Electronics products are classified according to the following three quality grades: "Standard", "High Quality", and "Specific". The recommended applications for each Renesas Electronics product
assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein.
depends on the product's quality grade, as indicated below. You must check the quality grade of each Renesas Electronics product before using it in a particular application. You may not use any Renesas
Electronics product for any application categorized as "Specific" without the prior written consent of Renesas Electronics. Further, you may not use any Renesas Electronics product for any application for
which it is not intended without the prior written consent of Renesas Electronics. Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the
use of any Renesas Electronics product for an application categorized as "Specific" or for which the product is not intended where you have failed to obtain the prior written consent of Renesas Electronics.
The quality grade of each Renesas Electronics product is "Standard" unless otherwise expressly specified in a Renesas Electronics data sheets or data books, etc.
"Standard":
Computers; office equipment; communications equipment; test and measurement equipment; audio and visual equipment; home electronic appliances; machine tools;
personal electronic equipment; and industrial robots.
"High Quality": Transportation equipment (automobiles, trains, ships, etc.); traffic control systems; anti-disaster systems; anti-crime systems; safety equipment; and medical equipment not specifically
designed for life support.
"Specific":
Aircraft; aerospace equipment; submersible repeaters; nuclear reactor control systems; medical equipment or systems for life support (e.g. artificial life support devices or systems), surgical
implantations, or healthcare intervention (e.g. excision, etc.), and any other applications or purposes that pose a direct threat to human life.
8.
You should use the Renesas Electronics products described in this document within the range specified by Renesas Electronics, especially with respect to the maximum rating, operating supply voltage
range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. Renesas Electronics shall have no liability for malfunctions or damages arising out of the
use of Renesas Electronics products beyond such specified ranges.
9.
Although Renesas Electronics endeavors to improve the quality and reliability of its products, semiconductor products have specific characteristics such as the occurrence of failure at a certain rate and
malfunctions under certain use conditions. Further, Renesas Electronics products are not subject to radiation resistance design. Please be sure to implement safety measures to guard them against the
possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas Electronics product, such as safety design for hardware and software including but not limited to
redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. Because the evaluation of microcomputer software alone is very difficult,
please evaluate the safety of the final products or system manufactured by you.
10. Please contact a Renesas Electronics sales office for details as to environmental matters such as the environmental compatibility of each Renesas Electronics product. Please use Renesas Electronics
products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. Renesas Electronics assumes
no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations.
11. This document may not be reproduced or duplicated, in any form, in whole or in part, without prior written consent of Renesas Electronics.
12. Please contact a Renesas Electronics sales office if you have any questions regarding the information contained in this document or Renesas Electronics products, or if you have any other inquiries.
(Note 1)
"Renesas Electronics" as used in this document means Renesas Electronics Corporation and also includes its majority-owned subsidiaries.
(Note 2)
"Renesas Electronics product(s)" means any product developed or manufactured by or for Renesas Electronics.
http://www.renesas.com
SALES OFFICES
Refer to "http://www.renesas.com/" for the latest and detailed information.
Renesas Electronics America Inc.
2880 Scott Boulevard Santa Clara, CA 95050-2554, U.S.A.
Tel: +1-408-588-6000, Fax: +1-408-588-6130
Renesas Electronics Canada Limited
1101 Nicholson Road, Newmarket, Ontario L3Y 9C3, Canada
Tel: +1-905-898-5441, Fax: +1-905-898-3220
Renesas Electronics Europe Limited
Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K
Tel: +44-1628-585-100, Fax: +44-1628-585-900
Renesas Electronics Europe GmbH
Arcadiastrasse 10, 40472 Düsseldorf, Germany
Tel: +49-211-65030, Fax: +49-211-6503-1327
Renesas Electronics (China) Co., Ltd.
7th Floor, Quantum Plaza, No.27 ZhiChunLu Haidian District, Beijing 100083, P.R.China
Tel: +86-10-8235-1155, Fax: +86-10-8235-7679
Renesas Electronics (Shanghai) Co., Ltd.
Unit 204, 205, AZIA Center, No.1233 Lujiazui Ring Rd., Pudong District, Shanghai 200120, China
Tel: +86-21-5877-1818, Fax: +86-21-6887-7858 / -7898
Renesas Electronics Hong Kong Limited
Unit 1601-1613, 16/F., Tower 2, Grand Century Place, 193 Prince Edward Road West, Mongkok, Kowloon, Hong Kong
Tel: +852-2886-9318, Fax: +852 2886-9022/9044
Renesas Electronics Taiwan Co., Ltd.
7F, No. 363 Fu Shing North Road Taipei, Taiwan
Tel: +886-2-8175-9600, Fax: +886 2-8175-9670
Renesas Electronics Singapore Pte. Ltd.
1 harbourFront Avenue, #06-10, keppel Bay Tower, Singapore 098632
Tel: +65-6213-0200, Fax: +65-6278-8001
Renesas Electronics Malaysia Sdn.Bhd.
Unit 906, Block B, Menara Amcorp, Amcorp Trade Centre, No. 18, Jln Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia
Tel: +60-3-7955-9390, Fax: +60-3-7955-9510
Renesas Electronics Korea Co., Ltd.
11F., Samik Lavied' or Bldg., 720-2 Yeoksam-Dong, Kangnam-Ku, Seoul 135-080, Korea
Tel: +82-2-558-3737, Fax: +82-2-558-5141
© 2011 Renesas Electronics Corporation. All rights reserved.
Colophon 1.0